Satellite L30-134 no sound through speakers using Win XP SP3

Similar Questions

• Satellite L30-134 PSL33E sound card driver does not

  There is no setup.exe for the sound card in the download?
  and it will not install manually with the inf file

  can someone point out the correct link for the drivers for sound card for this laptop

  Satellite L30-134 PSL33E

  Have you tried C:\Toolscd in the RealTek folder? I removed, because it takes too much space, and when I had the problem with the driver (I also Satellite L30-134), I downloaded from:

  http://support.toshiba-tro.de/tools/satellite/sl30psl33/XP/sound-PSL33-XP-51005273.zip

• Re: Satellite A200 PSAF6A - his plays through speakers using headphones

  When I plug my headphones into the port, nothing happens, still plays through the speakers.
  Is it drivers or something, because I want it redownload.
  I have a Toshiba Satellite A200 PSAF6A.

  Hello

  This seems to be an Australian series for Toshiba laptop.
  You can find it here:
  http://www.ISD.Toshiba.com.au

  You will find the audio driver and the most recent BIOS.

  But I recommend to check the sound settings first.
  I guess that's a Realtek audio chip in the Realtek audio Manager panel you could supply some parameters that control the headphones and speakers.

  Tab of reading on the right you will find the headset by clicking right into this and check the options that are available.

• Satellite L30-134 - after HDD upgrade PC freezes and won't start

  Hello
  I upgraded my Satellite L30-134 of the standard 60 GB HDD for a new 120 GB. After that, I have the following problem:

  (1) after installing XP form to the recovery House DVDs works fine but after that 2-3 weeks of normal use it instantly freeze pc and after hard reboot the OP start up can do anything but to format the HARD drive. After that format cannot install original XP and Vista, the progress bar show me that the installation is complete but after reboot, nothing happens. This problem persists long wery. After 3-4 clean up one after another the pc starts and runs very well about 3 weeks. What is the problem? Any idea?

  (2) when I first install Vista or Linux PC is runing fine, but not in normal parameters. Always freeze but after hard reset works fine for about 2-3 days. When I install XP first that the PC is useles after hard reboot the only thing I can do is to format the HARD drive and do a clean install.

  PS: The HARD disk is produced Original Toshiba.

  Hello

  This strange boyfriend s but to me it sounds like that, these problems are caused from the new HARD drive that may be defective.

  I think you should test the HDD using Hitachi Drive Fitness Test:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT
  With the Drive Fitness Test, you can test your HARD drive. Download the CD image, burn it to a CD and boot from it. You can then the HARD drive test.
  On the same site is a user's guide if you want to know more.

  Good luck and give us feedback, what happened! :)

• Unable to connect the mouse or the keyboard on Satellite L30-134

  Just bought new Satellite L30-134. Try to connect monitor via a belkin, switching, separate keyboard and mouse device. Keep an eye on fine, but the keyboard connection problem or the mouse. Both are connections PS2, I used PS2 to USB switching device. Sounds complicated, but I thought that it would be "plug and play". Whenever I connect keyboard or mouse, error message saying device connected unknown.

  ANY HELP APPRECIATED

  Thank you

  Mark

  Hello Mark

  Can you please try to connect to some new keyboard or mouse? May be time to use recent hardware components with new laptop models. Use some modern mouse and keyboard and it will certainly be "plug and play" device.

• For the Archives: The upgrade of the Satellite L30-134

  I'm one of those old cell phones off a friend who had retired as being obsolete.

  However with a little time and money, it is possible to upgrade to a very usable machine.

  Not a power by any stretch but perfectly adequate for browsing the internet and watching videos (about 720 p watchable) standard definition etc.

  So as the search of these forums for more information for this project, I found a lot of conflicting advice, and some of my questions were not answered at all. I hope by documenting my experiences here I can help someone in the same position in the future.

  * Model *.

  This machine is the Toshiba Satellite L30-134, part number: PSL33E-00E013G3. It's probably very similar, but not necessarily the same as the other models L30. No invert them.

  * Original configuration *.

  Processor - Intel Celeron m 410 (Cache of 1 MB, 1.46 GHz, 533 MHz FSB, Socket M). It is a simple version of the Core Duo (Yonah core) processor core. It shares nothing in common and is not swapable with the previous generation Pentium M or processors Celeron Mr. He is also incompatible with the next generation of Core 2 Duo/Solo and Pentium and Celeron processors derived from these.

  Memory - A single 512MB SODIMM PC2 - 4200 (DDR2-533 MHz). This differs from the previous generation of DDR and the next generation of DDR3. The controller memory only supports single channel mode. There is no loss that the FSB of the processor is not fast enough to take advantage of the dual channel anyway.

  * BIOS *.

  My laptop came with very old version 1.3. Toshiba provides the latest version (3.10) for download. This is reported to be buggy and mess with the profiles of fan so I decided to leave it alone. I can confirm that my updates work without updating the BIOS.

  * Updates *.

  Processor - I swapped the Celeron for a Core Duo T2350 (1.87 GHz). Everything I read that all the Yonah core Core Duo/solo, Pentium and Celeron with a FSB of 533 are compatible. The FSB 667 models are not.

  The Core Duo T2450 at 2 GHz is the highest performing compatible processor but double the price on eBay. I paid just £12 (used) for the T2350 so there is really no reason to go down now, all of these parts are obsolete.

  RAM - there are 2 slots on this machine. Toshiba State a maximum of 2 GB, 1 GB in each slot. Unfortunately, the memory controller is very picky and survey of the weird errors, unless you get just the right ones.

  There is not enough information to understand it so for me it was a process of trial and error. Fortunately, I found an online retailer that guaranteed compatibility in 100% and returned by mail for free.

  The second pair of Poles worked well.

  Thanks for sharing!

• Re: Satellite L30 - 134 PSL33e shows 896 MB of RAM, but 1.5 GB are inserted

  Satellite L30 - 134 psl33e-00e013g3.
  I have 2 memory slots, in the first place there are 1 GB kvr, then I add to the second slot 512 MB Hynix
  All of the memory two modules are ddr-533 (little difference in hours between them is present)

  If I click on my windows computer properties shows me only 896?
  On the official form of toshiba. subject memory says I can go to 2 GB of ram.
  BIOS is the latest version!

  How can I add more ram in this model?
  Aida64 shows me in the slot1 = kingston 1 GB
  SLOT2 = 512 hynix
  but aida shows that the memory system 896.
  All modules in memory works great separately in all slots...

  Thank you

  Post edited by: workman24

  Hello

  That says the BIOS?
  BIOS sees the 1.5 GB of RAM?

  As far as I know that the laptop can be upgraded up to 2 GB of RAM (2 x 1 GB)
  The ATI graphics chip also shared memory.
  This means that if you installed 2 GB of RAM, a main part of this memory would be shared by GPU.

  It would be interesting to know what value would be reported by system using a single module (1 GB or 512 MB)

  by the way: what memory is shown in DXDIAG?

• Satellite L30-134 - question about upgrade CPU and video performance

  Hi have updated my satellite l30 - 134 with a bus t2450 dual core @2 ghz 533 Mhz = cpu is runing swell-marks look nice... BUT - my video performance droped a lot - grafics 2d - to top but 3d grafics are very poor why? driver problem?
  have also 2 g ram 2 x 1 g kinmax @ 6xx runing @533

  can anyone help? see that are some similar configs on this site... then maybe you can help me
  I'll try editing a xp 64 bit (curently runing xp sp3 32-BIT)

  > I'll try editing a xp 64 bit (curently runing xp sp3 32-BIT)
  Forget that don t recommend install Win XP 64-bit.
  Why? Because the Win XP 64 bit was not so popular as Win 32 bit or Vista/Win 7 64 bit and you won't find many drivers for Win XP 64 bit.
  Stay with XP 32 bit or you can change to Win 7 64 bit.

  Regarding the graphical issue;
  Have you noticed that also using the old CPU (Intel Celeron M Processor 410)?
  If this were not the case, then I guess this could be a problem between the CPU and BIOS.
  Otherwise I would recommend upgrading the graphics card driver.

• Satellite L30-134 will not accept 2 GB of RAM

  I looked at my laptop and it takes a maximum of 2 GB of DDR2 RAM, I tried two different pairs of sticks of 1 GB and the two blue screen that loads the OS.

  When the sticks do not go it simply ignores the second run, but I can't seem to accept 2 GB.

  BTW I have upgraded to a core duo processor, don't give me no problem.

  Known fixes for this problem?

  Hello

  Your laptop can be upgraded up to 2 GB of RAM. That s is definitely possible!
  You can use 2 modules of memory vivid x1024MB.

  If you would taka glance at this page, you will find information that you must use the DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM modules.

  [Memory for Toshiba Satellite L30-134 | http://www.orcalogi.co.uk/asp/prodtype.asp?prodtype=25737&ft=m&st=3]

  I presume that you always get a BSPD because the RAM modules are not fully consistent or simply malfunctioned.

  Welcome them

• Toll-free indicated what power disconnected from the Satellite L30-134

  I don't know it this the appropriate category, because I'm not sure of the source of the problem.

  Okay, here it is:
  I have Toshiba Satellite L30-134.

  Normally, when I unplug the cable of the AC adapter, 2 things happen:
  1 ATP icon shows that the current generator is the battery, and it shows invoiced % and about working time remaining before the battery is empty.

  2. the power management becomes more energy saving settings, and implementation Hibernate just until the battery is completely down.

  Well... Last few days things have changed:

  Now, when I unplug the power cable, the system does not recognize this and she continues to display: ' course Power Source: AC Power ', for the remaining capacity of the displays: "S/o" and the system is not hibernate, because he does not feel the difference.
  I'm not sure that this has something in common, buy, I found that the UPS SERVICE has been stopped, I tried to start it manually, but there is ERROR 2481: the UPS service is not configured correctly.
  Need help, please :-)
  OS: Windows XP, automatic updates, I did not notice if this happen after installation or any other measure of speciffic, I did...

  > Normally, when I unplug the cable of the AC adapter, 2 things happen:
  > 1. ATP icon shows the current generator is the battery, and it shows invoiced % and about working time remaining before the battery is empty.
  > 2. Power management becomes more energy saving settings, and implementation Hibernate just until the battery is completely.

  This process is correct. After disconnecting the AC adapter the laptop switches to the battery power and uses the Toshiba power saver mode the power created for the use of the battery.

  > Now, when I unplug the power cable, the system does not recognize this and she continues to display: ' course Power Source: AC Power ', for the remaining capacity of the displays: "S/o" and the system is not hibernate, because he does not feel the difference.
  > I don't know he has something in common, buy, I found that the UPS SERVICE has been stopped, I tried to start it manually, but there is ERROR 2481: the UPS service is not configured correctly.

  Well the ups (uninterruptible power supply) service could be responsible for this problem!
  If you are not able to start it manually, then it might be a problem with OS software.
  I studied a bit and found this article in the Microsoft Knowledge base about this problem.

  + Cannot start the UPS Service.
  http://support.Microsoft.com/kb/310437

  Good bye

• Re: Can I upgrade RAM on Satellite L30-134?

  Hello!

  My laptop is Satellite L30-134 (PSL33E-00E00WRU).

  I want to use RAM DDR2 800 Mhz 2 x 1 Gb in there. Is this possible?

  On the motherboard FSB speed is 533 MHz so I advise you to use compatible RAM modules.
  I don't know why you want to use these Rams from 800 MHz. For more performance or what?

• Where can I download Toshiba Satellite L30 - 134 dirvers?

  Hello!.

  I have a Toshiba laptop Satellite L30-134, but I don't have a CD for it. I downloaded the drivers on the side, but he could not work. Please help me!
  THX!

  Your ad is quite confusing so here some facts for you:

  Satellite L30-134 obviously comes with Windows XP Home Edition operating system.
  Laptop comes with two brackets: support recovery and CD of additional software.

  All the drivers, tools and utilities for this model of laptop, which you can find on Toshiba download page under http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=EU
  Here, you can find all this for Windows XP Home and Vista edition.

  I don't know what you're doing, but if you use install own OS please follow the order of facilities listed in the Instructions of facilities document.

  For WXP installation please use the CD of Windows XP SP2 home edition installations only.

• Upgrade memory for Satellite L30-134

  I have a Satellite L30-134, which seems to work pretty slowly - I think that due to the large amount of photos and music from itunes.

  I wonder which is the best way to solve - buy a memory upgrade (no idea how to change memory well) or get an external hard drive?
  And if I change the memory I'll lose what is already saved on the laptop?

  I agree with Ganz most HARD drive will not improve performance but increase the disk space available HARD, it would be you can store more music and picture on HARD drive ;) files

  Upgrade memory also would not provide a performance gain of course performance could be a little better because most of the things would be handled directly in memory and not in time on the HARD drive, but generally it s not really noticeable.

  In any case if you want to improve memory, check this:

  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=25737&ft=m&St=3

  You must use DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

• Satellite L30-134: is it possible to determine the frequency of 533 MHz RAM?

  Hello!

  I have Satellite L30-134 and used a module of 1 GB / 667 MHz (sic!) for a while. Same Toshiba says maximum speed 533 MHz memory he recognizes module PC-5300 and sets exactly to 667 MHz.

  I decided to increase the RAM and bought another PC-5300 1 GB stick.
  ... RAM is only 1 GB with two modules together. The two sticks are OK - L30 sees 1 GB and works well with each of them separately.

  I know that the reason is that Toshiba couldn't work with greater speed on the two banks (or something like that).

  So. It seems to be a good idea to set the frequency of 533 MHz and it should work.
  The only question is to know how to do it? BIOS Setup is almost empty and does not have these settings.

  One advise, please (except to buy sticks more :)

  Hello

  Laptop Satellite L30-134 is a processor 1.5 GHz of Intel-Celeron-M (Yonah).
  Is this good?

  This processor supports a 533 Mhz bus and if you use modules of 533 Mhz RAM then will automatically solve this value!
  Simply put, you do not need to change anything manually! Everything is controlled automatically.

  Concerning

• No sound through speakers, no sound through headphones, with the exception of a few videos.

  DV7-6c90us w/Beats audio Entertainment PC. IDT High Definition Audio Codec. The drivers are "up to date". Device Manager indicates that this sound card does not work correctly. No sound through speakers. No sound of Blurays / DVDs. DVD reading slow and erratic. Sound will play with some videos, both on the hard drive and online. Sounds Windows play in the headphones. I did a scan of root of Avast Antivirus and PC Cillin Housecall. Not found any viruses.

  Please, any help would be appreciated.

  Download & save the last Audio driver. Go into the Control Panel, programs & features - software uninstall IDT. Reboot the laptop. After loading Windows, install IDT audio by using the downloaded file.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5218634