Satellite L450D lost wireless connection

I have a laptop Toshiba L450D and just put Win 7 Pro 64-bit on with a clean install and downloaded all the drivers and install them BUT now I can connect only to the internet will open the Earthnet cable connected.

Any help please?

Hello

Your wireless network card is recognized correctly in the Device Manager?
Do you see a yellow exclamation mark in device-> network cards Manager?
Check it!

If there is a yellow exclamation points, it means that your Wlan driver was not installed.

The right WLan driver can be found here:
http://APS2.toshiba-tro.de/WLAN/

Tags: Toshiba

Similar Questions

  • Satellite L500 - lost wireless connection

    My Satellite L500 recently lost the wireless connection. I looked towards the top of the Realtek wireless device in Device Manager and it says that the device is functioning properly. I tried to use "ping 192.168.1.1" join the router, and I get "error Transmit - general failure."

    Any ideas?

    Hey Buddy,

    And now Windows recognize some WIFI networks at your fingertips? Your validation lost wireless connection isn't very useful

    You should try a WLAN driver update that you can download from the official page of Toshiba:
    http://APS2.toshiba-tro.de/WLAN/

    If you can't find or connect to WLAN networks deactivate in the Windows of the WLAN power save mode power profiles. You will need to set for maximum performance.

  • My laptop lost wireless connection after hibernation I or stop it. Then I have to reset the automatic Wireless Configuration to find my wireless connection

    I just bought a new NetGear wireless router and now my laptop lost wireless connection after hibernation I or stop it.  Then I have to reset the automatic Wireless Configuration to find my wireless connection.  Whenever I stopped him it and I have to choose.  This does not happen on another laptop or desktop that I have.  Is there a safe solution for this?

    Hi Ron,

    1 Windows operating system you are using?

    2. you receive messages or error codes?

    You can read the following article and check.

    Windows wireless and wired network connection problems

    If you use Windows XP, then read the following article:

    How to troubleshoot wireless network connections in Windows XP Service Pack 2

    This problem can also occur when the power management profile turns off your network card.

    You can try the following steps and check if it helps.

    a. click Start, type device manager in start search and press ENTER.

    (b) in Device Manager, expand network adapter.

    c. now you will see your network adapter or adapters if you have more than one. Right-click on the network component, and then click Properties.

    d. go to the power management tab.

    e. ensure that all check boxes are unchecked (check boxallow the computer to turn off this device to save power is off).

    f. If you have disabled the boxes, click ok and restart your system. Put the computer in Hibernate mode and check if you still have any questions.

  • Satellite L450D-13 x - lost wireless connection and will not sign up to all the

    I have a Satellite L450D - 13 X, I was able to use the wireless until today where it has stopped working. No matter what I do, it says that the wireless device is disabled.
    I tried to update and diagnoses, but they all come back fine.

    Can anyone help?

    Try to restore OS to an earlier time using System Restore tool. Maybe some update Microsoft screwed up the WLAN functionality. Very often the driver WLAN is displayed as an option to update.

    Try this as the first step.
    Also try restarting your router.

  • Satellite L450D-128 - Wireless internet does not connect

    Hello

    I have a Toshiba Satellite L450D-128 and it won't let me connect to a wireless network and I can't find the switch wireless and ive tried FN + F8, but it does not work. Could you please help.

    Thank you Ryan

    Hello Ryan

    I don't know what version of Win7 do you use and what can be the problem of using WLAN but if you use original recovery image, everything should work properly.

    At first check please if the wireless network card is installed correctly. You can check in the Device Manager.
    If the wireless network adapter is installed correctly, it must be enabled. Usually, this can be done by using the FN + F8 key combination.
    >.. .and ive tried FN + F8, but it does not work
    What does not work exactly? You have problem with the FN keys in general or just using FN + F8?

    When you press the FN key you find cards flash at the top of the screen?

  • Satellite L300 - losing wireless connection

    Hello

    (loss of wireless connection)
    I'm not technical interest in this area, but rather disturbing and it is worse, I thought I would post this question to see if anyone new what it was.

    This laptop is new (Toshiba Satellite L300-1BV) Home premium 32-bit.
    This happens a lot and it can be "A PAIN" and really fustrating, I suddenly lost my wireless connection and I can't view available wireless networks to try to connect again, especially since I have to restart the laptop and everthing is back to normal.

    He can be nice days then all of a sudden, this will happen, but why am I not pick up all other available networks.

    Network provider... BT YAHOO TO BROADBAND
    Router... BT HOMEHUB 2.0
    network card... REALTEK RTL8187B WIRELESS 802. 11B / G 54MBPS USB 2.0 NETWORK ADAPT.

    I know for interference and have done everthing possible to avoid this...

    Hello

    -Update the display driver
    -Update the BIOS
    -Disable the Save feature in WLAN power Windows power management
    -Check the WLAN standard (for example: 802.11 g or Draft N)

    In addition, you should read the hundreds of threads here in the forum on the problems of WIFI. It might be very useful! ;)

  • On Satellite L750/0 wireless connectivity issues s 5

    I own a laptop L750/0 s 5.

    I seem to have a problem with my wireless connection, where anywhere not at 10 m from the router the connection cuts in and out with the yellow sign 'limited connectivity' always appears. disconnect and reconnect solves the problem for a few minutes. Ive resorted to the close session of the router.

    the computer is 2 months old, the Wlan driver is up-to-date. power options have been configured to be on maximum performance for Wlan etc etc.

    The main thing that annoys me, it's all the others (much older laptops) in our House very much work where mine doesn't. I actually lost performance from where I can get my old toshiba portege m300 to this new wireless signals.

    In terms of information, the computer is running windows 7. Wireless network card is Atheros AR9002WB-1NG.

    If theres any other information that you need, as im sure there will be, I would like to know and ill try my best.

    The router is really new.

    Thanks for your help

    > the computer is 2 months old, the Wlan driver is up-to-date. power options have been configured to be on maximum performance for Wlan etc etc.

    The latest Wlan drivers can be found here:
    http://APS2.toshiba-tro.de/WLAN/?page=downloads

    Please keep in mind that you use the latest driver v9.2.0.419.0

    To be honest, I had the same idea to disable the power save for Wlan and it more often it should work are you sure that you have changed this in the same power station that is used when the laptop is running on battery power?

    However, it would be interesting to know if the Satellite L750 uses the same Wlan 802.11 standard, as do other portable
    In the Device Manager-> properties-> Advanced tab Wlan card, you can choose the standard Wlan 802.11
    Recommend to check this

  • Satellite L450D-11V - wireless issues

    Help, please!

    My Satellite L450D not find or connect to wireless networks. I tried to connect my laptop in various places where I know that wireless connections are available, but it keeps prompting me to use an ethernet cable.

    Any help or advice would be most appreciated as has happened for the last 6 months or more.

    If your laptop can not find any WLAN in your area, then you must check WLAN card.
    Open the Device Manager and check if the WLAN card is listed and installed properly.
    Wireless network card is enabled? Use the key combination FN + F8 to toggle WLAN card.

    Can you also tell us what OS you use and don't use original Toshiba preinstalled OS or your own installation?

  • Satellite L450D - need wireless driver for Linux system

    Hello

    I have a satellite L450D, with a Realtek RTL8191SE wireless card (windows 7). I use Linux for College and I can't get on the internet when I use linux cause the oporating system dose not find my wireless card.

    When I check from command line for wireless cards, it shows that there is not.
    I know other people who have had this problem and basically I need a driver for it.

    Can someone make me know what driver I need or where to find? I would really appriciate what I need to use Linux for the College.

    Thank you

    Hello

    I googled a bit and found some tips in the internet.
    It seems that there is no driver for Realtek rtl8192se WLan Linux and card rtl8191se.
    Had someone managed WLan installation by installing ndiswrapper from synaptic in Ubuntu + GUI. He downloaded the net8192se.sys driver W2K and net8192se.inf.

    W2k driver work but the combination W2Kxp driver or the xp or vista doesn t work.
    After that, you can use WPA because the WEP encryption is not supported

  • Satellite L300-1BW - wireless connection stops working after 10-15 minutes

    Hey!

    Just brought me a new laptop. Sound of the Toshiba Satellite L300-1BW. However, I've encountered a problem. I can connect to my home network wireless fine. However 10-15 minutes after browing internet, my just wireless connection will stop working.

    When does he say 'Local & Internet', 10-15 Minutes after that, I would say just "Local."

    I know full well it's not my Netgear because it work fine on all the other my computer.

    IM wondering if anyone could possibally help me. I would be grateful anyhelp.

    Thank you.

    Edit - seems work correctly with my laptop not charging. However when the power adapter is in charge of the laptop, it work for 10 minutes then stop.

    Hello!

    If you use Windows Vista, you must disable the WLAN energy saving function. You can find it in the Vista power management options. Check it!

    In addition, you should try to update the driver WLAN and the BIOS. The two you can find on the Toshiba site:
    http://EU.computers.Toshiba-Europe.com-online downloads support & -online Download Driver

    Last but not least, I would recommend that you read hundreds of discussions on the problems of WIFI. You will find so much tips and tricks how to increase the WLAN functionality and troubleshooting.

    Good bye

  • Re: Satellite P850 138: Wireless connection drops

    Hello

    I'm having the following problem:

    Sometimes the WiFi on my P850 138 will drop and the symbol beside the clock network connection displays an exclamation point.
    To solve the problem, I have to open my wireless network connection and disconnect and reconnect to my router manually.

    My P850 138 is connected to the internet via a connection from WPA2-PSK with a BT Home Hub 3.
    Note: The connection to the router is actually not lost, just connect to the internet.
    Also, the router remains connected to the internet.

    I would really appreciate some advice.

    Thanks in advance!

    > In order to solve the problem, I have to open my wireless network connection and disconnect and reconnect to my router manually.

    From my point of view this is not question of portable but a router problem.
    Have you tried to connect the laptop to another wifi hotspot in your area to test the feature?
    Recommend doing this

    In addition, you can also check if there is updated firmware for Wlan hub.

  • Satellite M70-173: wireless connection is not working properly

    Hello

    I am a novice and need help with Wi - Fi. I have laptop Satellite M70-173. My desktop pc is connected to the Netgear MR814v3
    802 11b cable/DSL with wireless router. I have connected the router to my broadband (telewest) and have access to the internet on my desktop pc. I turned on the connection Wireless via the menu of the router (the lights is on the router it's transmission). My wireless laptop is switiched on, BUT when I use windows on the laptop to get a wireless connection, nothing is detected. The laptop is 50 cm from the router. I tried and did the following:

    Firmware update,
    Made sure the SSID is the same on the router and the laptop.
    Wireless on laptop mode is on infrastructure,
    Wireless access point is enabled.
    List of access on the router is enabled,
    No encryption is used until I have run

    Any ideas any help?

    Thank you

    Hello

    Have you activated the wireless antenna?
    Please check if the switch wireless on the side of the unit is on. Also check if the wireless is turned on with the FN + F8 key combination

    Please check this possibility

    Concerning

  • On the Satellite A200-1CR wireless connection is not working properly

    Hello

    I have a problem with my wireless connection. In spite of I stay close to my router I can't access the Internet.
    If I have the connection, it is the level of 1 to 3 (5 is best).
    I have the same problem with "hot spot". I can't access the Internet or use only messenger, can't surf the Internet, check my emails, etc..
    Another person do not have this problem in the same places. They can access the Internet. What's wrong? Can you help me?
    I have a Satellite A200-1CR.

    Piotr

    Hello

    For most Wlan issues are related to problems of compatibility between the wireless network card and the Wlan router.
    Sometimes the Wlan driver allows to obtain the best performance.
    So, try to update the WLan driver first. Maybe it helps.

    Good luck

  • OfficeJet Pro L7780: Printer lost wireless connectivity

    The printer (which worked before wireless) has lost the connection to the router (wi - fi) for wireless printing and can not find the router when you run "Wireless Wizard". Have restarted the printer several times, but no chance connection. Summary diagnosis said the network name 'failed '. (I have with other devices wireless connectivity). The Configuration Page shows wireless status is disconnected and shows all zeros for the IP address and the subnet mask.

    Need suggestions on what to try next. Thank you.

    Turn off the router and back on again was! Printer has now found the router and is wireless printing. Thank you very much!

  • Equium L40 - lost wireless connection

    I have an Equium L40-156 under Vista and wireless became intermittent. The switch light would go out or maybe turn on at startup. In the end, I did a restore of the entire system from scratch and installed the latest drivers (Realtek) wireless.

    This seemed to cure the problem and it has been fine for the last 2 months. However, the light is now out again (it was working an hour ago), and there is no wireless connection.

    I tried a restore of the system and also installed the latest driver from Toshiba, but I still can't run. I hesitate to start over again once it takes all day to load programs and updates. Can anyone suggest what I can do or is this another bug of Vista?

    Great news

Maybe you are looking for

  • Satellite T130-11U: where can I get the original box?

    HelloI have a Satellite T130-11u, but I lost the original box. Where can I get another?Thanks for your reply. Juju

  • Windows Malicious Software Removal Tool - October 2011 (KB890830) bug

    Hello! After you install this update on my system I couldn't start over.My system has 2 to 3 monitors video cards. When I tried to start it, I saw the windows logo and the indicator of loading of the screen where it asks for the password never appear

  • Hard drive error, but passes diagnostic

    I have a vostro 320 all in one computer. Yesterday he left initializing with a hard drive error, but when I run the hardware diagnostics all past. When I go into the installer the Bious does not see the hard drive. Current Bious is 1.2.0 and current

  • Issue of signature PB SDK 2.0

    In previous versions of the SDK software PB file bbwp/bin/bbwp.properties used to have commented on the line [code] < !="" -="" -=""> company name -> [/ code] We need to remove the comment and add the company name, sign the apps. Now in the SDK 2.0,

  • Check the software on the client before granting access

    Hello I was wondering if it is possible to do an audit of the programs installed on the client before allowing access. Customers would be Win7 / Win10 machines with client anyconnect, that connects to an ASA 5512. I want to achieve the following obje