Satellite M40 - cannot boot from the recovery cd after format HARD drive

Similar Questions

• Satellite A10: Cannot boot from the recovery CD after the replacement of the motherboard

  Heres one in your brain is going...

  I recently started a format hard drive via the normal recovery CD, but it never finished as long as the power cut.

  Not to worry I thought, I kept all my data and a new motherboard was on order.

  The fitting of the new Council, I tried to boot from the recovery disc and all I get is 'non-system disk '.

  Then I replaced the HARD drive with a former to check the functionality of the Cd. The old disks (I tried two) both still booted from the cd and their HDs has worked fine once in windows.

  However...

  When I try to start any of these 'good' HDs from the cd nothing happens, nada zilch. In fact they will not start even to a 'Beginner PC' recovery disk either, so it's not the Toshy recovery disk.

  Another weird thing is when I go into the bios by pressing ESC the power upward and then F1 and try to change the boot sequence and press end to exit and save, nothing happens.

  If the CD is not defective because it is recognized in windows
  The recovery disks may not be at fault because the other disks also fail to start.

  This is not a drive problem hard as other HDs start normally (but not Cd)

  This could be a fault on the new motherboard, perhaps a problem with bios, or the sequence of events suggests something else?

  Any suggestions would be welcome

  Paul h

  Hello

  Long story. In my opinion you should write is a little shorter but with more useful information.
  I am interested in one thing: have you got a new mainboard or used one?

  To be honest, I'm also confused with the recovery disc you are using. The history is confusing.

  > so this isn't the Toshy recovery disk.
  Can you please tell us what kind of recovery CD are you using exactly?

• Satellite A200 - cannot boot from the recovery disc - code 1

  I have Vista business and my laptop is running slow and is full of rubbish.
  I have in the past used my drive recovery to completely re - install vista and start from a fresh version.

  However, I tried this once and it says that it cannot boot from cd - code 1.

  Can someone tell me what it is and how to reinstall vista?

  Hmm. strange.
  Are you sure you have the right recovery disk?
  Are you abele to boot using another drive as MS Win XP CD or Linux CD bootable?

• Satellite M45: Cannot boot from the CD-ROM or HARD drive

  I get the following messages...

  WHEN BOOTING FROM HDD: "Invalid partition table".

  At the START of the CD: "No Bootable CD in ATAPI CD-ROM.
  By so, even though I have the recovery CD and the computer can not read them.

  I tried to change the order of boot without result. Created a bootable CD Bart, who works in my other computer, but not in this laptop. Are there special drivers, I need for this CD?
  I'm out on this one.

  Thank you

  Hello

  I think that your partition on the HARD disk is damaged and so you cannot boot from the HARD drive.
  In this case, the HARD drive must be formatted completely and then you could try to install the OS.

  It seems also that your drive cannot recognize the CD bootable (WinXP?) and, therefore, it of not possible to boot from the drive.
  Well, it really stupid s :_| situation really stupid!

  However, did you try to boot from another CD? For example Microsoft Windows original CD?
  If not I recommend you to do and eventually the reader will be able to read the CD.
  If this isn't the case, so I think that the reader must be checked. Possibly it also corrupted s.

• How can I configure Satellite A300-148 boot from the recovery partition?

  Hello

  I had some problems when trying to install MAC - OSX, for her, where the partition table is deleted, then I retrieve the entire score as it is, but I can not start in any case.
  Then I decide temproraly install another copy of vista drive Vista (not the partition), then set up my laptop to boot from the recovery partition and reinstall the good copy.
  My problem is, it's all here, the only problem is, I need to configure the system to boot from the recovery partition.

  My device is:
  Satellite A300-148

  Thanks to the device.
  Ahmed.

  Hello

  If you have already changed the partitions of HARD drive and deleted files from the HARD disk, then your HARD drive recovery is too bad!

  But to make sure that the HARD drive recovery is not possible please press F8 immediately after the power of the laptop. Usually a start menu should appear and you should be able to choose the option called fix my computer. Then you should be able to choose recovery option.

  But like I said that this is only possible if your HARD drive was not formatted!

  If you have formatted the HARD drive and changed partitions then you will need a Toshiba DVD recovery that you have not because you didn t he create at the beginning. Is this good? Well, then you must order the recovery DVDs if you want to retrieve the laptop to factory settings.

  Welcome them

• I want to use the recovery disc for re - install my pavilion dv6, but cannot boot from the recovery disc?

  Now my system Windows 7 Home premium canbe accessed, but with a lot of problems. That's why I want to reinstall it. I burned my own recovery (totally 4 disks) successfully disks. I insert the first disc of recovery CD-rom and restart my laptop, but it can not recognized but in win 7 automatically. could you tell me how to use my recovery disks to reinstall the system win 7 when that is not totally broken?

  Hello

  Probably go to BIOS and configuration of the machine to boot from the CD/DVD ROM. Please follow the instructions from HP:

  http://support.HP.com/us-en/document/c00364979

  Kind regards

• Portege A200 - cannot boot from the recovery disc

  Hi, I have a Portege A200 and an original unused Toshiba Recovery CD.

  When I go to recover, the DVD drive just turns and turns and nothing happens. I have tried different methods of booting with the disk to like, by pressing the C key, select boot from CD/DVD or just turn it on with the DVD in the drive. Same problem, the disc turns right away.

  I also checked the drivers TOshiba download page and let down when I found out that there are several drivers for the same thing, like the 3 drivers LAN! Which should I use? Also, I can confirm that the CD/DVD drive works fine because I already loaded windows XP, no problem.

  Any suggestion is appreciated.

  Kieran99.

  Hey Kieran99,

  I also think that s is not a problem of the CD/DVD drive. If it turns over and over again once he recognizes a disc but it can t be read correctly.

  Regarding your question about drivers I think that it of fairly easy. I can recommend the vendor and device ID in Device Manager. With these identification numbers, you can search on this website http://www.pcidatabase.com/ to determine the LAN controller. All that s! :)

  In addition, you can check the ID s in Device Manager, if you click the LAN card properties > Details > PCI\VEN_xxxx & DEV_xxxx

• Iconia W3-810 cannot boot from the recovery disc

  Hi, I have a 32 GB Iconia W3-810.  The original recovery disk was lost.

  I made a Bootable DVD of 8.1 and also Win 8.1 bootable USB key.  These two have been tested on another laptop, and both can start this laptop to the installation environment.

  I also followed the guide to enter the BIOS of the Acer Tablet settings and change the boot order and change remove secure boot option.

  Unfortunately the unit keeps trying to start in Windows 8.1 - one who is full of viruses and should be flattened and start over.

  Help, please...

  Many of these cables power the Tablet via the splitter, but do not provide power at the side of the data cable from the side power (I don't think I explained that well). They are designed to power your device on the motor side while allowing access to data on the other side. If connected:

  Tablet- + - power
  
              |
  
              |
  
             DVD

  The Tablet receives power supply and Tablet provides the voltage and sends and receives data from DVD, but power does not give voltage on DVD. This means that the DVD does not necessarily receive the budget power that he needs.

  If you can, try the DVD connected to a powered hub. Turn upwards and actually to work are two different things, and tablets offer far less than the maximum power on their USB ports.

• Qosmio G35: Cannot boot from the recovery disc

  I'm in trouble from the screen of my Qosmio G35 showing lines vertical, gel, then a loop on and outside.

  I used the Toshiba factory restore disc to reformat and the problem remains, I went further and chose the maquis of the HARD drive option. Bad choices made by this beginner, because now it does not recognize the drive at all, prompting me to "initialize".

  Lines remain, but it is not the material of the screen happens during some process that I follow, OK.

  A friend more computer over the phone prompted me to go into the BIOS, but we cannot access them. Research on the web, I tried the F12 suggested, but this does not work, just push me through in a screen offering 'Safe Mode' etc.

  Any help would be welcome. Thank you

  Hello

  Usually the vertical display lines looks like a hardware problem, in my view, it could be related to GPU failure.

  In any case, we should start first of all the problem of CD/DVD drive you must check if the disc is properly recognized in the BIOS.

  For this, it must Access the BIOS press the ESC (if Toshiba BIOS) or the key F2 (if Phoenix BIOS). Please check these two options because I m not 100% sure what the BIOS the Qosmio G35 uses.

  But like I said earlier the issue looks like a malfunction of the graphics card and you must contact the ASP in your country for assistance.

  Best regards & friend good luck

• Cannot complete the recovery process after replacing HARD drive

  Hello

  I changed my hard drive it for 15 days because he showed abnormalities, so I bought a new hard drive Seagate Western brand with the same technical characteristics as the existing hard drive (product for the product).

  I was then on TOSHIBA HDD RECOVERY to burn to CD system recovery disks, then I went to replace the hard drive.

  After the change, I raised my PC with system restore CD.
  The procedure is successfully completed and orders of comments asking me to remove the disk and restart the PC.

  I raise the PC, everything goes well, launch windows, installation of perfect records system then comes the stage of installation and settings of the system here after the error message:

  "Windows Setup could not configure Windows to run on the hardware in the computer."

  Then it asks me to restart, then it comes back every time on this message, I'm stuck on this step.
  I tried to change the mode of the disc source hard 'compatibility' instead of 'AHCI' but it's even worse, it completely without error buggy.

  Please give me an explanation of this phenomenon.

  Sincerely.

  Guillaume

  Have you tried to repeat the whole recovery procedure?
  If this is not the case, do.

  I recommend to format the whole HARD drive and create an NTFS partition.
  Then start the laptop using the Toshiba Recovery disk and start the recovery procedure.

  I read about the problem of disk HARD similar in the past and especially NFS partition creation has helped to solve these problems.

• easy transfer can be used to reload the data files after formatting hard drive?

  I have been informed by level microsoft 2 I have to reformat my hard drive to fix the problem with windows backup (snapshot won't work).  easy transfer will copy all THE data files, including OUTLOOK 2007 on hard drive and then I can reinstall on reformatted drive.

  Easy transfer copy some things but not all things. He does more that can make a simple copy/paste (such as the settings for example) but, for example, not programs transfer (those who need to be put back in place).  Here is a description of what it does (and does not): http://support.microsoft.com/kb/928635.  It will transfer Outlook 2007 PDF files and other personal data if they are selected - you need to know which files you need and where to select them - but it won't transfer the program (which must be put back in place).  It must be run before you reformat the hard disk to collect data and then you can transfer everything what you have registered once the system is re-installled.  You would do the re-setup prior to the transfer.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Satellite L40 - 18W - USB ports does not work after format HARD drive

  I formatted my laptop "L40 - 18w" after that all usb ports do not work.

  Could you please help me on this issue

  Thank you

  Ben is right. After the installation of the operating system as a first step, you need to install driver chipset.
  Please see the download page for Toshiba under http://eu.computers.toshiba-europe.com
  There you can find all the drivers for your model of laptop including driver chipset.

• Vista 64 does not start after the bios screen. Can not boot from the recovery cd or help

  Last night a MS pushed a windows update and my pc restarted automatically.  But it does not actually restart.

  The PC goes through the bios tests, passes and then crashes and does not start in Vista.

  I can't start at all, including safe mode.

  I can't the system recovery option in HP bios to load.  Can I only use my Vista64 system recovery bootable cd or actually start.

  First of all, I thought it was a HARD drive problem, but tests of the bios disk hard that all spend, even the 2 hours 'SMART' test that he was running.

  Help

  Hello

  What happens when you try to boot from the recovery CD? You receive messages or error codes?

  You can check if the boot in the BIOS settings priority is configured to boot to CD\DVD.

  NOTE: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  For more information, you can consult the following article:

  BIOS: Frequently asked questions

  If you still experience the problem, you may need to contact HP for assistance.

  HP support

  Hope this information is useful.

• Can not boot from the recovery disc - 0x000000D1 Driver_IRQL_not_less_or_Equal

  original title: cannot boot from the Vista recovery disc

  A real problem. Vista is prompting me to boot from my recovery disc and allow the repair of Windows. However, when I insert the disk it shows loading Windows, but once he starts to launch I get the BSOd with the "Driver_IRQL_not_less_or_Equal" error report with the error code Stop 0x000000D1. I searched on advice but all I can get into the repair mode, but I can't. F8 does not work in safe mode. Week last ChkDisc has run on every start and yesterday I received a number of parts of Vista won't load does not with error reports. Today, it started with Windows can not load the warning and instructions for use the recovery disk... I'm in a loop as I cannot cross the BSOD! Help please

  Mick

  Computers are strange animals. After my response to you, I had another attempt to go beyond the blue screen. Hey hop this time my computer decided that he had enough rest and proceeded without delay to start and I would like to action, the recovery disk. There then reinstall Windows Vista and am now to a new computer! It's time to move to Windows 7! The only thing I did yesterday was to unplug my printer to my laptop!

• How can I get WIndows8 TouchSmart to boot from the recovery disc

  How can I get WIndows8 TouchSmart to boot from the recovery disc? With the recovery in the drive disk when I do a reboot or stop and start it does not read anything from the DVD player. My computer is a HP TouchSmart 23-D160QD.

  @AirForce9731,

  You may need to change the boot order to boot from the DVD drive first.  The steps to do this are in the document below.

  http://support.HP.com/us-en/document/c00364979

  These are recovery disks made by the recovery discs sent by HP?  They will not work in a different system (you will receive an error message), but you are able to get the boot floppies in a different system?  They should be able to start up to a point where the error message will be displayed.