Satellite P10-304 turns on but the screen is off.

Similar Questions

• Equium A300D - 16 c turns on but the screen does not show anything / remains black

  Hi, I have a laptop Toshiba Equium A300D - 16 c.

  It was fine until now...

  When I press the power button, my laptop turns on but the screen remains black / off.
  The indicator disk HARD is not Flash or anything... (in case that helps)
  I also tried to remove the battery, hold the power button for 30 seconds and then reconnect the power cord... Same laptop turns on but the screen is black.

  I tried to connect my laptop to my PC using a HDMI cable screen, but without success... Laptop turned on but monitor my pc showed nothing.

  I have not changed anything inside my computer laptop or unscrewed it.

  PS:
  Quite often, I kept my laptop on the bed/pillow it may have something to do with overheating or something.

  How did I get to this point:

  Yesterday, my laptop was fine, there was nothing wrong with her... I turned off during the night, but when I tried to turn it on this morning it is where I have faced this problem.

  Any help would be appreciated.

  Thank you very much
  Rejanu.

  Long ago, I had similar problem on my old Satellite. CPU was faulty. After replacing the CPU, everything was OK again.
  I put t really know what to say.
  Maybe you should contact Toshiba and let check your laptop. They have diagnostic tools and may know what is the problem.

  What do you think?

• Qosmio X 770 turns on but the screen remains blank

  So my Qosmio X 770 turns on but the screen remains blank, it was randomly turning every so often, but now it is just blank.

  The hd works fine again, I tried to plug it into a TV to see if it works, but no signal is found. I was informed by a friend that it could be a problem with the graphics card, I wonder if it can simply be exchanged if I buy a new one or if he joined, and I have to replace the whole motherboard?

  Any help would be appreciated.

  Even if the HARD drive is faulty, the laptop should be able to IT and you should see the home Toshiba on the internal display screen.
  If its definitely NOT drive HARD problem.

  You said that you have connected the laptop to the TV. You see the start of Toshiba on the external monitor (TV) screen? Are you able to access the BIOS by pressing F2?

  If this is not the case, there is certainly a hardware problem.
  It could be a fault of memory modules, graphics card or the same motherboard malfunction could be possible.

  GPU problems or the motherboard, the whole motherboard must be replaced and that's expensive fix because mobo belongs more expensive laptop.

• Satellite L40 is power on but the screen is blank

  Can someone help me with a problem?

  I'm not a computer expert and my laptop won't do anything. If I put power turns on but the screen remains blank

  Hello

  Try this:
  -Remove the battery and unplug the AC adapter from the portable computer
  -wait for about ~ 40 min and reconnect the two parts
  -then try to turn on the laptop

  If this does not work and the laptop does not start in windows OS, then you could try to insert a bootable recovery disk Toshiba and could attempt to reinstall new OS.

  If the procedure still does not have a hardware malfunction is possible, and in this case only the authorized service provider would be able to help.

  Good luck

• Satellite A300 - system still works, but the screen is blank

  Hello

  I was downloading an update of tempro toshiba (synco or something in that sense) for my laptop Satellite A300 and the frozen screen. I pressed the power button for 5-10 seconds until it is turned off. When I turned it the system seemed to work but the screen is completely black.

  I tried to remove the battery, and fn + F5 but the screen still won't turn on.

  Any help or advice would be appreciated.

  Rob.

  Hello

  It happened because of the updated BIOS, or during the common software update?
  In case it was an update of the BIOS I recommend contact the ASP in your country, because it seems that the ROM module must be flashed again.

  If it happened during a common software update, so I advise to remove the battery and the AC adapter and wait an hour.
  Then reconnect the two parts and check to see if you could power the laptop properly!

  Check it out!

• MacBook Pro 2015 turns on but the screen remains black...

  Hello

  Today, I tried to turn on my MacBook Pro, but my screen stays black. When I press the caps lock button, it turns green which I guess means he lit. I've also heard the startup chime it generally makes when you turn on. I already tried to turn it on and off several times and reset the SMC and the LANDAU... The screen is always black.

  Could someone help me please?

  Also a few minutes ago the fan has started to make noise in the macbook...

  But the screen remains black.

  Thank you

  Shaynidw

  Hi shaynidw,

  From your description, it seems that your MacBook Pro is powered, as soon as you hear the startup chime and see the light on the keyboard.  Thus, it seems that the problem may be with your screen or the video card.

  On the screens you see when you start your Mac

  Power on

  

  When you turn on your Mac, display is off (black) and you hear a startup chime. Your Mac Initializes his BootROM and memory (RAM live). It then performs a power - on that self test (POST) and a test of BootROM. If you hear beeps or chimes at this stage, this indicates a possible hardware problem and start stops. If you add memory to your Mac, check that it is installed correctly.

  White screen

  

  After that only walking self-test is completed, your Mac sends a video signal to your connected screens. The screen may appear black or grey at this point in the boot sequence and backlight of the screen should light up. If you do not see the image appears on your screen after a few moments, try increasing the brightness of your screen. If you use an external monitor, make sure it is properly connected and turned on.

  shaynidw, if set up the brightness of your screen does not help, you have an external display (computer screen or TV) that you can attach to your MacBook Pro to test?

  In addition, you can try to start your computer in safe mode to see if you get different results.

  Try safe mode if your Mac does not end commissioning

  If the problem persists, you may need to take your computer to an Apple Store or service provider authorized Apple , so they can inspect the video card and cables to isolate the problem.

  Take care.

• Satellite P10-304: bad sectors on the disk - how to fix?

  My drive HARD drive bad sectors developed and replacement needs, does anyone know how to do this?

  My model is a P10-304.

  In addition, Windows will not start upward in my old HDD because of bad sectors and the drive is protected by Norton and back, does anyone know how to bypass or disable round trip

  Hello

  I found these tips how to disable the Norto Go Back tool.
  You can uninstall it from your computer, disable GoBack to your laptop press 'space' GoBack screen button and select the option "disable" GoBack.

  Follow these steps:
  1. reboot your computer.
  2. when the Norton GoBack splash screen appears, press the SPACEBAR.
  3. in the Norton GoBack boot menu, click on disable.
  A message informs you that disable Norton GoBack erases history and you will not be able to run the hard drive or hard disk restore advanced restore until Norton GoBack is turned back on.
  4. click on Yes.
  5. click on continue.
  Your computer restarts automatically, and Norton GoBack is off
  After restarting the laptop, I recommend once again using the following key: CTRL + ALT + G.
  Immediately press on and hold the keys Ctrl + Alt + G after restarting the laptop you. A message you giving the possibility to force the removal of GoBack master boot record. Press F to force the removal of GoBack master boot record.

  If failure of keys Ctrl + Alt + G in the first time then try this again for three or four times until you get the prompt to remove the master boot record of GoBack.
  Finally, restart the computer.

  To fix bad sectors on the HARD drive, you could boot from the XP CD to use the console of "repair".
  And then use the CHKDSK /p command to repair the bad sectors.

  Good luck

• HP Desktop turns on but the screen says no signal?

  I have a hp slimline s3020n PC which used fully turn on... monitor reads "no signal", but the office is on (lights up and I can hear the fan). I already bought a new monitor and a new cable, but it still does the same thing, which leads me to believe this is not not a parts problem. I also tried to reset the BIOS of the computer but nothing happens... can someone help me as to what I can do?

  Hello

  As there is a message 'no signal' you work your way back to the screen and the connection cable to the graphics card and the motherboard to make sure that everything is connected.

  Buying a new monitor is an expensive way to solve this problem, you can swap comes to a friend's computer to see, this is the cause.

  Here are the specs of your computer:

  http://www.HP.com/hpinfo/newsroom/press_kits/2007/desktopdesign/ds_s3020n.PDF

  You have replaced the monitor and cable between the monitor and the computer, the next thing to look at is the graphics card.

  As it is a desktop computer, you can open and edit the graphics hardware.

  If it is not the graphics card (onboard), this is normally a problem within the motherboard itself.

  Do you get that unique "beep" when you turn on your computer, which means that the motherboard has spent his own self test (POST), or you receive a series of 'beeps '?

  If you do not receive a single "beep" you have hardware problems.

  See you soon.

• HP Pavilion g7-1261nr turns on but the screen remains blank

  I turned on my HP Pavilion g7-1261nr the other day, and the fan ran hard, as well as the caps lock and number lock LED flashes once every two seconds. The screen remains blank during the process. Could someone help me with this problem please?

  PcMatic I invite you to read the links provided, because they are there to help.

  If you entered my link, you would have seen this:

  Caps Lock/Num Lock LED component tested error Condition

  LED flashes 1 time CPU CPU not functional

  2 times for BIOS BIOS corruption failure LEDs blinking

  LED flashes 3 times non-functional Memory Module error

  LED flashes 4 times Graphics Graphics controller not functional

  Map of 5 times the system board failure system general LEDs flashing

  Authentication failed for the BIOS BIOS 6 times blinking of the LEDs

  According to the times that they blink, of what I mean, it's once and then a pause. Which would indicate that the CPU is broken.

  Only a repair can fix that.

• BlackBerry phone of Q10 is on but the screen is OFF

  Hello

  My problem came from nowhere. I have no leave falling or damage my Q10 (OS 10.3). My battery was almost full, but when I wanted to check something the screen just lights. The keyboard-lighthouse was lit, I could hold the mute button to start the votes programm and I heard the sound of starting the program. everything seems to work, the screen is totally black.

  what I tried:

  -J' took out the battery, tried to restart... nothing fixed it.

  -J' loaded for 10 hours

  -J' have now pushed start button-> a red light is displayed for 3 seconds and sometimes the keyboard light went

  - I could connect to the computer and make a backup, even if I removed the battery before and could not restart it!

  After about an hour, it fixed itsself. I could use it as usual again. These situation keep stacking and I count 3 times now. what I can also send it in?

  Thanks for the help!

  Eric

  Is the unit under warranty? Otherwise, you can remove and reinstall all connections to the motherboard if you feel uncomfortable with it, or bring it to a repairer and ask them to do.

• Laptop turn on but the screen is completely black

  Hi guys,.

  I was wondering if someone have an idea as to why my laptop (which was working perfectly last night), now has a black screen when I try to turn it on.
  I read in some other forums who offered to take out the battery and hold the power button, but that didn't work...

  Remedies?
  Thank you.
  Jess.

  Hi Jess

  Is a busy HARD disk when you start your laptop?
  You hear Windows sound?

  If possible try to connect your laptop to the external screen or a TV to see if you can see anything on an external device.

• Need drivers for Satellite P10-304

  Hi all

  I was wandering if someone could point me in the right direction.

  I bought a second hand satellite P10-304, had to replace the hard drive and operating system and now need drivers. Unfortunately the P10-304 model doesn't seem to be on the list of drivers.

  If someone could let me know what letter it is or it is a pro, etc, I would be very grateful.

  Thanks in advance

  Steverino

  Hello

  All drivers for older models of laptops you can find under http://eu.computers.toshiba-europe.com > support & downloads. But please, under product type choose ARCHIVE. In the lower corner you can find the label with the exact model number. This model number must be set to download under Model No short option page.

  If you have any other questions please post again.

  Bye and good luck!

• Satellite L40 - does not start and the screen is completely blank

  Hey guys,.

  A good friend of mine has a laptop Toshiba Satellite L40, who died recently, and she has not been able to find the warranty documents yet, so I wanted to ask if maybe you could help.

  Basically, what's happened is that one day she was using the computer and not have noticed that it was not plugged in to charge, and before completely lost all power, the computer went into automatic hibernation mode.
  It plugged into the charger, the lights indicated that he was in charge. A few hours later she was trying to turn on, but nothing. the computer itself gives off a sound very low, as if turned on, but the screen is completely blank. She said that it's almost like she couldn't make the thing out of hibernation mode. He continues to give sound and some indicators remain lit until the battery is running out of charge.
  She has Windows XP is installed on the computer.

  Perhaps someone could help as to what is happening here? 1 million thanks!

  ME

  Hello

  Weird, but have you tried to remove the adaptor AC/DC and battery? Wait one hour and then reconnect the adapter AC/DC and battery. Maybe the laptop restarts.

  If this isn't the case, I think that you need assistance from an authorized service provider. It seems to be a hardware problem and the laptop should be checked by a technician from Notepad to determine the cause of this problem.
  On the Toshiba site, you can search the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Good luck!

• NB200-10Z starts but the screen is blank

  Hello

  I have a Toshiba NB200-10Z netbook.
  It turns on but the screen is blank.

  Can someone help me coz I don't know the cause of her

  Hello

  Try this:
  Remove the battery and unplug the AC adapter.
  Then wait a little (1 hour should be enough)
  Then reconnect both sides and try to turn on your NB200.

  If it s not a serious issue, then your NB200 should turns correctly.
  Otherwise it s a serious question, and you will need professional help from a technician of the ASP.

• Acer blue 720 and the fan are on but the screen remains black

  Hello

  I appreciate any help that can be provided.  I tried to remove the batter on my daughter 720 and reinsert, but this problem persists.  I can hear the fan and the blue light turns on but the screen remains black.  I tried to rest for 30 seconds and esc, refresh and power.

  Thank you

  Well, when the scrween does not at all (even in text mode which allows a recovery) then it is most often a problem with the cable bwteeen the motherboard and screen, most often following it is a failure of the screen (which requires generally a matter of co-location as cracked screen) and from time to time, it is the motherboard. Probably time to contact Acer support to see on a repair.