Satellite P200D died - nothing on the screen, no HARD drive noise

Similar Questions

• Low beginning on Satellite M40-145 after changing the 160 GB HARD drive

  Hello

  I own a Satellite M40-145 since 2005. After more than two years without any problem, two weeks ago the 80 GB hard drive to the original address has been damaged. So I had to replace it with a new, 160 GB (this replacement was made in a store because it's out of warranty).

  I used successfully on the new HARD drive recovery CD to install Windows XP and all the drivers (just as when it was new).
  I used Partition Magic to create a partition of D for data. Also, I installed Office 2003, Norton 360 and connected to the Internet.
  It worked quickly with only small problems than perhaps with little patience I could fix: as this Bluetooth hardware is not detected and the wireless switch began with the lights off even being in the position we (it worked with new just switching out-lit again). But suddenly, after only one day of use, Windows starts became very slow. It takes about 4-5 minutes until it is possible to use the laptop.

  Now, I tried many possibilities to solve the problem, but always ending on the same problem: I used the recovery CD again and try to use the computer with or without updates (I thought that maybe the problem was due to a bad update), with and without Internet access, etc.
  I also tried in vain the program Microsoft Bootvis to try to speed up the startup, etc.

  I even created an image with Acronis to only with XP and Office running fast, so that I could install it again and try new things.
  I also tried to clean the registry with various programs like CCleaner, TuneUp 2008
  Also the defrag JKDefrag and PageDefrag. But always returning to the same problem after a few days of good conduct.

  I don't know what else I could do. I wonder if maybe the new HD is damaged (although I test and no error or no damage was detected) or if the update BIOS might resolve this problem (I'm not and that's a big risk).

  Please, could someone help me?
  Thank you very much for your attention.
  Pablo

  In my view, that there is nothing wrong with the software or all drivers on you laptop.
  I think the key is the enormous size of the HARD drive.

  The difference between 80 and 160 GB is huge.

  To my knowledge, the BIOS supports a limit on the size of HARD drive and I really wonder why the 160 GB HARD drive has been recognized by the BIOS.

  However, I think you should test a 100 GB, 120 GB HDD if the same question perhaps if poster using a HDD a size smaller.

  Best regards

• Satellite A210 - 11 p - gos black screen and HARD drive does not

  Hello

  My Satellite A210 - 11 p suddenly goes to a black screen and the hard drive stops working. It is always under tension and if I want to restart I have to unplug the unit and remove the battery.

  I thought it was overheating and checked the time and they were really high in the 1980s. I took the fan and cleaned (very dusty) and the basic form of thermal paste. Temperatures plummeted now immediately but I still have the same problem, I updated the graphics driver and watched the temp on GPU (which is fine) but the problem is still happening. I used a number of programs to check for errors on the hard drive and no reported problems. I reloaded Windows 7 but still no joy.
  The problem seems to occur at any time and is not due to the execution of a given program, even just browsing with firefox

  Not too sure what to do and any advice would be welcome.

  Hey Buddy,

  > I reloaded Windows 7 but still no joy.
  Have you ever tried with Toshiba Recovery disk operating system?

  The Toshiba recovery disc there is an image of the settings from the factory with all the drivers and tools. If you install Windows on this disk, you factory back.

  That would mean if you have the same problem after the installation of recovery it s really bad hardware working because you have pretested settings of Toshiba. In this case an authorized service provider can help you make an accurate diagnosis what part is affected.

• Satellite A100-906: Question on the processor and HARD drive temperature

  Hey guys,.

  I want to ask u for the level of normal temperature of this laptop? I want to know the temperature of the CPU (1,2) and the temperature of the HARD drive, because I think that my laptop is overheating and it is a problem for me :/ (my temperature is now around 50 for the 2 hearts and nearly 40 for hard disk) Is this ok or? Ty ;)

  Hello

  Believe me, the 50 degrees C for the CPU and C 40 degrees for the disk HARD is a normal temperature! It's rare!
  On my laptop the CPU temperature increases up to 60 degrees C if no application works.

  But be aware that the temperature varies.
  If you run different applications on the laptop, the performance of the processor will be increased and the temperature rises.
  That is a fact.

  There is nothing wrong GUY ;)

• loud fan after the addition of hard drive noise

  I installed a second hdd in my Mac Pro 2008 and as soon as I started there was a noise constant very loud fan as I never had before. Here's what I put: WD2003FZEX WD Black 2 t 7200 RPM SATA 6 gb/s 64 MB cache. I formatted using disk utility. This is my first time, install a hard drive and I basically screw them into the bracket and connected. Did I miss something?

  Try resetting the SMC

  Reset of the management system (SCM) on your Mac controller

• Satellite P200 - 14: nothing on the screen when the power

  Hello

  I have Satellite P200 - 14 h, and a few days ago I started having a problem power on my lap.
  I press the power button / stop, all three LEDs light up, battery, power supply and the first that shows that the adapter is plugged.

  Now my problem is that the Satellite txt is not lit, and nothing indicated on my screen.
  It's the mouth vent, black, on the bottom of the laptop, spin for a couple of times, and they stop

  Does anyone know how to fix this
  Thanks to 1 million...

  Sounds like a serious problem of material.
  Please don t understand me wrong. This is only my personal opinion... If you want to know exactly what's wrong and then the laptop must be controlled by an ASP.

  But try this first before you contact the ASP.
  Remove the battery and unplug the AC adapter
  Wait about 30 minutes and then reconnect the two parts.

  Try turning on the laptop computer.
  If that does not help, ASP is your next step

• Re: Satellite Pro A200 - no activity - nothing on the screen

  Hello!

  I have a lot of problems with the Toshiba Satellite Pro A200.
  Same problem for all: when you connect the power adapter led turns blue!
  When I press on "on" button the second led turns blue, the fan runs for a while, but there is not activity: nothing on the screen.
  No thing hard disk led...

  I have a lot of this problem with the Satellite A200. The motherboard is a LA - 3481P.
  I am an electronic engineer and I m specialized in laptop repair card main but I did not understand this problem.

  Can U help me telling me that maybe the defective chip?
  Thank you very much

  Hello

  I don't know if you saw that this forum is the forum of users and you should not wonder if nobody can give the exact answer. As an electronic engineer, you must know that no one can answer specifically and to find the good chip, you must run diagnostic tool.

  So I think that you need professional help. Try to contact nearest Toshiba authorized maintainer and ask for help.

  BTW: I am really interested about new comments here.

• Equium L10-273: fan of CPU/HDD / lights come on but nothing on the screen

  I have an Equium L10-273 and had to put in a new power outlet in the mobo.
  I removed the wide and electronics. A friend of my put news on that to get back together.

  It sounds if the HARD disc / CPU fan / lights come on but nothing on the screen.
  Have unplugged the cable from the screen and he recovered but not good.

  Any suggestions welcome

  PS: A mobo out on a Toshiba Equium A60-155 will be mine?

  To me, this looks like a motherboard problem.
  In my view, replace the whole motherboard.
  But it s only my personal suggestion, if you want to be 100% sure what's exactly wrong with you laptop, then go you and technician of the notebook check.

  PS: Don't think that a card mother Equium A60 - 155 to insert in the notebook Equium L10-273.

  Greetings

• Nothing on the screen when Tecra A7 reboot

  For about a week, my Tecra A7-201 shows a strange question.

  When I reboot then there is nothing on the screen, but the machine continues to boot.
  I can connect to the machine with MS Office remotely and in the Device Manager I see that there is no graphics cards and also without monitors listed.
  I can stop the machine and then remotely and the same thing happens again to restart.
  To get the screen back, I need to disconnect the power to the machine, remove the batteries, wait about 30 seconds, put battery back/ac on and now I have my screen back.
  As I can't even Toshiba/BIOS boot screen to display everything that this happening before that windows never loads.
  It happens too regardless the State of home (docked/undocked) or voltage (AC or battery only).

  I have no idea if the partners, but also the screen sometimes "flashing" - like lightning just a fraction of a second and returns to normal.

  I'm running the latest BIOS 5.60.

  Clues? The machine is still under warranty (and has been back to Toshiba for another problem already - so it could be a machine on Monday).
  I asked Toshiba here in Switzerland and I get no response, just need to look at the machine (which means that it is gone for another week).

  Thanks for any help

  Peter

  Hello Peter

  I don't really know what the problem is here (probably related equipment), but please do not contact Toshiba but partner service authorized in Switzerland. If you need address, you can find them under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true

• 3 beeps pause 3 beeps pause nothing on the screen

  3 beeps pause 3 beeps pause nothing on the screen

  Hello

  Sound beeps are error codes that describe a problem with your machine. A continuous beep
  can mean keyboard (loose or bad cable), losing the card, power, a short circuit or other matter according to the
  System/BIOS manufacturer. The model 3 beep indicates similar type problems.

  Startup and select CONFIGURATION/SETTINGS (BIOS/CMOS) - usually F2 that you start - look to see BIOS
  Creator, then see here:

  Computer MESSAGE / beep codes
  http://www.computerhope.com/beep.htm

  If my computer beeps and won't start, what do the beeps mean?
  http://KB.IU.edu/data/afzy.html how to troubleshoot Beep Codes
  http://pcsupport.about.com/od/nonworkingcomponent/HT/beepcodestb.htm

  POSTAL Codes beep
  http://www.technick.NET/public/code/cp_dpage.php?aiocp_dp=guide_beep_codes

  Power on Beep Codes post
  http://www.pchell.com/hardware/beepcodes.shtml

  It may have other check so with system Maker or a real computer store (the one that makes its own internal
  service and not of leeks and glances at a Best Buy or other stores).

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Nothing on the screen, wallpaper only. The office has no icons and the taskbar are missing.

  Original title: nothing on the screen, just wallpaper

  I can't turn on my computer, and when I click on my user name I have to enter a password after clicking on enter nothing appers only my background wallpaper but not the icons, the taskbar or anything, the only thing I ca see is the cursor when I move the mouse. What can I do to get my icons and my taskbar and everything back on my screen?

  "blankdesktop" wrote in message news: e3df0065-10 c 4-47f1-8199-8a750f4c3b90...
  > I can turn on my computer, and when I click on my user name I have to
  > enter a password, once by clicking on enter nothing appers only my desktop background, but
  > no icons, the taskbar or anything like that, the only thing I ca see is the
  > cursor when I move the mouse. What can I do to get my icons and my taskbar
  > and everything back on my screen?
   
   
  Try to use the salvation of three fingers (C-A-D, Ctrl + Alt + Delete) to bring up the task
  Manager - then click on file > new task (run...)
  type
  SOLUTION EXPLORER. EXE
  and see what happens - so try a system restore to a working system.
   
  HTH
   
  --
  Noel
   
   

  Noel Paton | Nil Carborundum Illegitemi | CrashFixPC

• Start Windows vista, nothing on the screen, only the pointer of the mouse

  I have a gateway desktop vista, nothing on the screen, only the pointer of the mouse
  I used the recovery tools nothing fixs

  Hello

  "I used the recovery tools nothing fixs.

  It helps us if you tell us what they were.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If necessary, here's how to reinstall back to new condition.

  "Gateway Recovery Center in Windows Vista® '

  http://support.gateway.com/s/software/MICROSOF/Vista/7515418/7515418asi.shtml

  Read these options to the gateway address:

  Gateway System Recovery from the hard - the following are methods to recover or repair the computer using the recovery of hard drive partition.

  • Complete recovery plant
  • Restoration with automatic data backup
  • Windows recovery environment

  See you soon.

• My computer makes a noise but nothing on the screen, theres a light on the modem if

  for the past few weeks that my computer will not start up - which is nothing on the screen, yesterday he started upward and today for a few minutes then froze now cannot get on... I got a blue screen problem as well... do you think that there is nothing I can do or not? I am running windows vista

  Hey doz1990,

  I was not able to locate the specific page for this model computer. I suggest you email or by looking at the manual (if you do not find your they're online too, just use a search engine) and go to them via e-mail or a phone call.

  Looks like it could be a serious hardware problem, but I can't say without more information.

• M17x R1 does not start - black screen - fan turns, turns on the keyboard, nothing on the screen.

  Hi all

  Newbie here and desperate.

  I have a problem with M17x my son this morning. Everything worked very well and after some time, turned off the machine it self.  Now it does not start even - at least I think, it won't because there is nothing on the screen as it is empty.

  I've tried several things, including trying to move on and outside, with or without a battery of the power cord.

  I'm at a loss as to what could have happened.

  Help, please.

  Smakwam.

  The gpu of cooking is very easy in fact, that you have designated your oven to about 275 degrees cover a cookie sheet with paper and configure the map out of it by winding 4 balls of aluminum foil and their definition on each corner of the map. you never want to have it put all directly on the sheet. do Cook for about 10 minutes then cool before coming back into the laptop. Always be sure to remove all of the components and the radiator and any residue of thermal paste. After sick cooking you need to reapply a fresh thermal paste. I use artic silver 5. It is has more detailed instructions on this online, as well as photos. You want to make sure it's your video card before you do it just to be sure. I just had to do it again last week, works like a charm for me every time.

• Satellite L70-A-139 - guaranteed zero when removing the cover for the RAM and HARD drive

  Hi all

  I have a Satellite L70-A-139 youcef.
  And at the back of the laptop, there is a cover that is fixed with a screw.

  Wil I void the warranty when I unscrew and take a look?
  I want to upgrade my HDD to SSD.
  The motherboard supports Sata III: D.

  Thank you!

  No, the mandate must still be valid.
  There is a removable cover at the bottom of the unit as shown here:
  [Toshiba Satellite C70 / C75 / C70D / C75D / L70 / L70t / S70 / HARD S70t drive replacement procedure | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm]

  Then you should be able to upgrade the RAM and HARD drive.
  I think this info should be mentioned in the user manual too.