Satellite Pro 6000 continuous beep and do not post

Similar Questions

• During BIOS update by Satellite Pro A60 went down and did not start

  Hi all

  I have a Satellite Pro A60 and I've updated the bios. To halfway the update, my laptop came down and started Hasna´t since. It only give a couple of beeps (trying to tell me the bios is damaged, I guess) and turns off again.

  Tried to start with (~) key pressed (a tip I received from a friend), but without success.

  I live in a country where there is no available Toshiba dealer and I rather not ship the laptop for repair.

  Does anyone know how to fix this? Any help would be greatly appreciated.

  Thank you

  This doesn't sound good.
  If during the POST, the BIOS detects a problem, it will normally display an error message visual on the monitor explaining what the problem is. However, if a problem is detected before it initializes BIOS video card or a video card is not present or not detected then BIOS will play through the Speaker beeps to let you know there is a problem.
  Depending on the type of BIOS you have the BIOS can play beeps in a specific pattern to indicate what the problem is, or emits the signal even a few times indicating the problem.

  In your case, it is possible to s you used a bad BIOS or bad BIOS procedure. Both can damage the motherboard.
  To avoid such damage and mistakes, Toshiba published FAQ document.
  How to upgrade the BIOS on most of the units!

  That you should read before making updates to the BIOS!
  Unfortunately, I n t think that you can fix yourself. I think you should ask to help ASP.

• Satellite Pro L450D black screen and will not respond to any keys

  Hello

  My niece has used his Toshiba L450D for almost a year now and he really liked it, who was until last month. She turned on her laptop and when she presses the button of the mouse, the button cracked and he fell into the laptop.

  Now my brother contacted Toshiba and I was told because it is under warranty it might return for repair because it was a common fault. Then he he packed in loads of air bubbles and a box to make sure it was safe.

  A few weeks later he came back repaired but we were all shocked that the laptop was put in a very loose box and you could hear this rattling noise. When we turned on the battery was flat and we had a new boot menu.

  As she installed it Windows 7 laptop would boot directly into Windows 7, but now after the repair of the laptop shows a menu black screen with as follows:

  + Windows 7 +.
  + Recover Windows to Factory Settings [active EMS] +.

  So we started in Windows and everything went well, but now after 5 or 10 or even 20 minutes, laptop displays a black screen and will not respond to keys or mouse movement. There is nothing on the screen its just black.

  I started in SafeMode (which was more difficult with the new menu) and it does the same thing. I even managed to do a virus scan quick who took 3-4 minutes and was clean.

  I would like some advice on what my niece is very angry, and it's difficult to explain what is happening to a child in the primary school.

  Any help would be grateful.

  Hello

  Have you tried the option of HARD drive recovery?

  If this is not the case, try to set the notebook back to factory settings using HARD drive recovery.
  Turn on the device, press F12, choose repair my computer, then select Toshiba HDD recovery.

  I hope it will work!

• Satellite Pro 6000 stop reboot

  Hi, can anyone help? I installed sp2 on satellite pro 6000. Now, it will not be stopped, just restarts. Did not it before sp2. Any ideas?

  HI Martin,

  I myself remember when I installed SP2, it needs to stop and restart the laptop in order to complete the installation process. It would seem that there problems on your system. I suggest you remove SP2 and re - apply to see if that remedies the situation.

  HTH

• Satellite Pro 6000 and Windows Vista

  I bought a Satellite Pro 6000 and I want to put Windows Vista on it. I did an Upgrade Advisor and I was told that this graphics card will not work. Is this true?

  Thanks, Nick

  I'm afraid that's true. Satellite Pro 6000 is old enough for laptop and it will not supported in Vista. Install Windows XP Home edition and enjoy your life.

• Satellite Pro 6000; sleep function does not work after upgrade W98 SE to XP

  I bought a windows XP cd and installed on W98 on my Satellite Pro 6000. The sleep function does not work now. I probably need a software of Toshiba. What do I need? Where can I find? What is the order of installation?

  Hello

  All drivers Windows XP Home edition, tools and utilities you can find on Toshiba support page under http://eu.computers.toshiba-europe.com > support & downloads. You have old laptop model and because of this type of product, you choose option ARCHIVE.

  Order of the facilities is as follows:
  -Windows XP
  -Display driver
  -Audio driver
  Toshiba - common modules
  -SD Card host driver
  -SD Card Driver
  -BlueTooth Stack
  BlueTooth - Easy Connect
  -Mouse driver
  -Modem driver
  -LAN driver included with Windows XP
  -Infrared driver
  -Toshiba Power Saver
  Utilities - Toshiba
  Toshiba - post Mobile
  -Toshiba Console worm.
  -Toshiba Hotkey for display devices

  I hope that you will be able to install Windows XP Home edition successfully.

  Good luck!

• Not detected in satellite pro 6000 integrated wireless card

  Hello

  my company has two satellite pro 6000 with wifi built-in.
  I'm sure that when we have received laptops led wifi turn properly when the wifi switch is activated.
  Since we had no wifi, never bothered us check.
  Now, it seems that the card is not detected, it does not appear in Device Manager.
  Runing xp SP2.

  Fred

  Hi Fred

  Y at - it the same problem with two laptops?

  Have you tried to start the Hardware Wizard? If the card is there it will be shown, and if the card will not be detected that it is possible that this card has been removed.

  Check it out.

• Satellite Pro 6000 - new RAM does not work

  Hi all

  New to this forum sorry if this was asked before, I did a search but could not find anything so here goes.

  I just bought a new RAM for my Satellite Pro 6000. When I install it nothing happens the laptop won't boot. If I put the old stick in no problem. The ram I bought is unb 512 MB PC133 CL3 and old RAM 256 MB PC133s. I think little small to read with these old eyes.

  I was told I might need an update of the BIOS but cannot find one for my laptop under 1.4 for the moment.
  Any help would be thank Lindsey

  I think that the new RAM is not compatible with the motherboard or laptop.

  The manufacturing of the new RAM you said does not for me so I would buy an another RAM, such as Kingston. Kingston makes high quality RAM and many users here buy Kingston RAM to upgrade its RAM.

  By the way: do you use the RAM or only the new? Normally, if you use two memory modules live, you must use it with the same specifications.

  The update of the BIOS, you can find the Toshiba site, but this doesn t affect the compatibility of Aries.

• Satellite Pro 6000 and SD-R6472 DVD burner

  In response to my previous posting (now locked), the engraver of the SD-R6472 DVD can be used with Satellite Pro 6000.

  Firstly used the dreaded IDE 1 # error will be encountered, but not panic, this can be overcome by asking the Technical Support CSEL-Changer Toshiba Software and this will change the master/slave setting of the drive.
  After that, everything works fine.

  Hello

  Thanks for the useful information.
  I'm sure that this information will help other users who have similar problems.

  Good bye

• How to remove the old fan and heatsink of the Satellite Pro 6000

  Hey people,

  Is there anyone who can help me with instructions step by step to remove the fan and the heatsink, I have a Toshiba Satellite Pro 6000...

  Concerning

  Barnie

  Try this guide shown here:
  http://www.irisvista.com/tech/laptops/Toshiba6100/Toshiba_Satellite_Pro6100_dismantle_1.htm

  The 6100 is almost the same as the 6000. This guide should be a big help. (Click on each image for a more detailed view).

  Kind regards

  chain

• Satellite Pro 6000 display turns off sometimes

  Hello

  I hope someone can shed some light on a problem with a laptop Toshiba Satellite Pro 6000 that I can't seem to get to the bottom.

  The laptop has Windows XP Professional installed and works fine, except for the fact that intermittently (could be 5 minutes, maybe 90 minutes) the display screen is what I can only describe as 'blocks '.

  The o/s plant (I ran BACK and Tests of diagnosis when the problem occurred) I would say movement of waves of mouse to the screen and activity HARD drive software continues running, except the screen is unreadable with blocks of color scheme.

  Any ideas or suggestions as to what this could be, and how I could go about repairing it?

  Hello

  It's very strange question.
  Have you tried to update the graphics driver? If not then please select this option.

  Besides if the update doesn't fix this eventually it there something wrong with the hardware. In this case, it is not easy to say what could be wrong.
  In your case, I recommend you connect the external monitor if the problem occurs.
  If the color blocks will also appear on the external monitor so eventually the graphics card or motherboard is corrupt.

  But, if the problem occurs only on the internal laptop display, so I would say that there is something wrong with the display or the FL-inverter.
  In this case, you should contact the technicians to solve this problem, because guys have more experience than each common user like me and you.

  Good luck

• Satellite Pro 6000: video controller - driver compatible vga

  Hello

  I have a Satellite Pro 6000 but I can't watch DVD because they run very slowly.
  That's probably because my video controller is not installed, but I can't find a
  Driver video controller for a 6000 SP. My OS is XP.
  Can someone help me?
  Thank you

  Hello

  You need to install the Trident display driver. You can find it on the European driver Toshiba page in the Archive folder.
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Choose Archive-> Archive Pro Satellite-> Satellite Pro 60xx-> Satellite Pro 6000-> Win XP

  By the way; You must use a special software like PowerDVD or WinDVD to play and watch DVD movies!

• Satellite Pro 6000 won't start or do something

  Hello

  My satellite pro 6000 stopped working all of a sudden.
  Power led, battery, keyboard LED is on, but nothing happens, tried to remove the battery, cd, hd and put them back, nothing seems bad.
  Also tried the back button back in case but no tip was not all good.
  It just won't start at all.

  Any ideas out there?

  Thank you

  [Edited by: moderation of the Forum]

  Do the job of seem´to LEDs ok, or they do a code flashing for you say that it is something wrong?

• Damaged BIOS 1 - Satellite Pro 6000 block

  Hi all

  I bought a laptop, a Satellite Pro 6000, but after a few weeks, he refused to start and gave me the bios message 1 damaged block.

  I downloaded the update to bios on the toshiba site, but it does not work.
  I have an external floppydisc. When I put the .exe to upgrade the bios on a floppy disk and turn on the laptop with the ~ button, I get the message "ready for the update of the bios, place the update disk and press any key when ready."
  I can hear the disk is searched, but nothing happened.

  How do I update the bios or is there something else wrong?
  Any help would be appreciated!

  In my opinion with the BIOS update you can't do anything wrong.
  If you BIOS, update by following the procedure described in the document FAQ Toshiba and the BIOS update can not be done properly, I'm afraid there is a problem with the BIOS chip and it may be defective.

  I can't say for sure, but if the BIOS chip is damaged, then you have a big problem.

• Satellite Pro 6000 - how can I update the BIOS?

  Hi all

  I have the problem that my laptop does not start 9 of 10 times with the message: * block 1 BIOS is damaged, call your service man.

  I want to update BIOS but for the Satellite Pro 6000 I can only find an update the BIOS from Windows. But my laptop does not start! Rarely the machine starts, but when I try to update the BIOS, I get the message that I already have the latest version of the BIOS

  My questions:
  * Is there a BIOS update file that is a BIOS floppy? (for example the Satellite Pro 6100 has 2 BIOS files, 1 Windows and 1 making a floppy disk)
  * Is it possible to update the BIOS with the same version of Windows?

  Or perhaps there is another solution for this problem? Has no need to update my BIOS?

  Thank you.

  Hans

  Hello

  I agree with Luke.
  The rom Bios module seems to be damage.
  Either it must be replaced or flashed again.

  But you won't be able to do that! The update of the Bios on the Toshiba page focuses on winning and you will not be able to update if the windows are not running.

  You last chance is an ASP that could check the BIOS ROM.
  As I said, most high, maybe new reflash module Rom help but cela can be answered simply by an ASP technician who checked this.