Satellite Pro A200 - 18 p - mic / headset does not work with Vista

Similar Questions

• Satellite Pro A200 series - CD/DVD-rw does not work

  I've had the laptop for a few months and it's great but now I try to add documents and music on CD or DVD and it will not write. The machine can play DVD +/-R/RW and CD.

  I have tried both DVD + RW is simply not found and the CD - RW try to write, but then the operation cannot have place towards the end of the process it says it cannot be completed.

  Any advice?
  Drives running on my desktop drives are very good.

  Hi Rebecca

  In most cases, these CD/DVD burning issues are related to mediums is not compatible.
  You should know that not all of the CDs or DVDs of different manufacturers are compatible and supported
  I would recommend so test different CD and DVD.

  What burning software do you use?
  I use the program Nero Burning Rom. It of great and supports many useful features. This software tested the CD/DVD drive and controls and sets the best burning speed.
  Sometimes it s useful to run these tests to ensure the best combustion parameters.

  But you question might be linked to the failure of hardware too.
  Sometimes the reader cannot process a CD or a DVD because the lens can not calibrate correctly. In this case, the disk must be replaced :(

  So finally I recommend that you check the different CD & DVD, and if the problem persists, contact the ASP in your country for a control.

  Bye and good luck

• Bluetooth headset does not work with Windows 7 - device is detected.

  I have a Dell XPS 1530, which had Vista 32 bit running. I have recently upgraded to Windows 7 Ultimate. Ever after that the Bluetooth of DELL BH 200 headset does not work with my laptop.

  The bluetooth adapter and the device is fine since I'm able to search and find all bluetooth devices, including my helmet. However, I get a yellow exclamation on the headset under devices. The headset can be paired with other devices such as my mobile and works very well.

  I tried to update the drivers and reinstall the device and the adapter from the Device Manager. We have a similar setup on my brother's computer and it works fine.

  Another thing to watch, would be what battery is used.  I know from personal exp some devices work with Toshiba stack, vs the MSFT pile up.  Do a search and see if anyone else uses a different battery with these devices. Network systems engineer * Zvetco biometrics * Windows Server 2008 R2 * Core 2 6600 @ 3.30 GHz * 16 GIGS RAM * NVIDIA 9400GT * * > please VOTE MESSAGES ALSO USEFUL TO HELP OTHER USERS

• Re: Satellite L300D-13s - WiFi does not work with Vista

  I have a L300D-13s that came with Visa Home Premium on it.

  His work very well outside the wireless that refuses to work.
  I always "Wireless Association failed because Windows did not receive response from the access point or wireless router.

  The wiresless is a Realtek RTL8187B Wireless 802. 11b / g 54Mbps USB 2.0 Network adapt
  I am running the latest version of the BIOS and the 6.1148.924.2008 drivers dated 2008-09-24. If I use the latest drivers on the RealTek site, I get a message about an unknown error.

  If I use the NETWORK Ethernet card, then he gets a fine IP address so this isn't the show indicator to publish.
  Its not wireless security (I understand that Vista does not support WEP 128 bit). I turned off and it still does.

  Other laptops running XP connect correctly and this laptop connects fine using no security or WEP or WAP so I boot Linux.
  If the problem obviously lies with Vista and/or the drivers.

  If someone has solved this.

  And no - don't tell me to go out and buy a router "Vista compatible".
  If Vista does not work with router XP and other operating systems compatible with Vista is wrong.

  Hello

  > Other portable XP connect correctly and this laptop connects fine using no security or WEP or WAP so I boot Linux. If the problem obviously lies with Vista and/or the drivers.
  I would say it is not a Vista problem or a Realtek driver problem because I have a Vista and Realtek WLan card and I can connect properly to my router.
  In you case, I would say that there is a compatibility problem between the router and the Vista because as you said the laptop can connect properly using Linux.

  I have goggled a bit and could solve most of the people who have had this issue, update the firmware on the router s.

  Maybe you should try that too.

• Logitech USB microphone does not work with Vista, Service Pack 2, PC. ____

  My Logitech USB Desktop Microphone does not work with my Vista, Service Pack 2, the PC.  He asks the driver, but Logitech says it's in the Vista software, here is the largest part of the error message:

  Windows has detected a new device attached to your computer, but did not find the driver software, to make the device usable. Each device manufacturer typically includes the driver from a CD that comes with the device, or for download on its Web site.

  Signature of the problem: Problem event name: PnPDriverNotFound Architecture: x 64

  This seems to be a problem that's happened, but after searching for hours, I can't find a quick solution.  Any help?

  Hello

  Please do as I suggested in the answer above is probably the solution.

  You can also do this after the above.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Satellite Pro L10 - FN + F5 view command does not work

  When I attach my Satellite Pro to an external CRT, LCD monitor or projector, I get the same problem each end every time.

  the Fn + F key to toggle the display of control does not work.

  When I start the laptop with the attached external display device, everything is fine, and the display is exclusively channeled in the external display. but as soon as windows has started, the display switches to the screen of the laptop, and there is no way to make it back.

  y at - it an update for this problem, or another solution I know not?

  Thank you.

  Hello

  Seems to be a simple software problem.
  I put t know how long you OS runs on the laptop, but maybe some files registry entries are corrupted and therefore the FN key does not work as it should.

  Could help to reinstallation of the OS and the use of the recovery CD

• Satellite Pro A60: TV S-VHS on does not work

  I have a Satellite Pro a60 and I'm pulling out my S-VHS to function... This does not work very well.

  I connected all the cables right and right click on the desktop, again choose preferences, then on Preferences, but I can't find anything on the transmission of the video signal.

  I have not though as the configuration standard of Toshiba, but that shouldn't matter. I'm running WinXP SE, but the drivers for my card ATI is about two years old and I can not find a suitable one anywhere, this is the problem, or should I program utility ATI?

  Best regards!

  Hello

  You should also check the TV settings. You must choose the right channel.
  As in the previous announcement suggested, you can change the display device using the FN + F9 key combination.
  If you want to play the DVD with the WinDVD player for example if you first need to change the output of the TV and then start the WinDVD.

• Satellite Pro L20-212 - USB 2.0 does not work

  Hello

  I own a * Satellite Pro L20-212 *, * Windows XP (SP2) is installed, but USB2.0 does not work *. I see nothing on USB 2.0 in the Devicemanager and the speed of the USB 2.0 devices attached is at the level of the USB 1.1.

  I don't know what information is needed to help me with this problem as it should normally work on my laptop (and I know that the laptop has USB 2.0 ports).

  What I have to install a special driver to use USB2.0 or is there any software on my laptop that I need to activate?

  Thank you very much
  Frank

  Hello

  Did you install the image on the Toshiba Recovery CD? This image contains the Windows operating system, Toshiba drivers and additional utilities. After installation, everything should work fine, and also the USB ports should work also.

  The USP ports, you can find in Device Manager in the serial BUS controller universal section. Open the tree and check if there is some yellow exclamation points.
  Then try to remove the Device Manager, the controllers and the USB hub and restart the laptop. After restarting again the OS should recognize USB controllers deleted again.

  I hope that this accelerated procedure will help you.

  Greetings

• Satellite Pro 4200 overheating because the fan does not work

  I have a satellite Pro 4200 and it keeps overheating because the fan does not work I went in and everything seems ok but then I power it upward but the fan does not work someone can help? all cables are connected the fan run at all.

  Hello

  And how to help her in this situation? If you are sure that it cooling fan doesn t work 100% needs to be replaced.
  By the way: did you clean the unit and remove the dust?

• Satellite Pro C850-1EQ - 8 tiles Windows does not work

  Hello

  I'm desperate for help try to solve this problem with my laptop. When I got my laptop (at Christmas) the majority of the tiles on the home screen windows 8 worked, however after a week or two they have gradually stopped working, which is very frustrating.

  When I click on a tile, it opens on the screen but the wheel continues to turn and nothing loads. I spoke to Microsoft online, however, they said that the problem with Toshiba as the laptop was purchased with Windows 8 already integrated.

  Suggestions, they did involving anti-virus and updates did not work.
  The most frustrating part is the Windows tile store does not work so I can't try to updates or new downloads to see if they will not solve the problem.

  Of course, I can use my laptop without the tiles, but I'm upset that I paid extra for Windows 8 and chooses the best part of it not working!

  Any advice on what to do next would be great, thanks in advance.

  Guess what? Try to restore the system Windows 8 back to the factory settings.
  Here you will find documentation how to do this:

  [Windows 8 recovery & repair | http://aps2.toshiba-tro.de/kb0/TSB2A03ES0000R01.htm]

  I recommend using the option * reset your PC *.

  + This option "Reset your PC" is useful when a PC is changed hands, or when you want to get a completely fresh start on a PC, without previous files of the selected configuration. +
  + The delete all, then reinstall Windows option permanently removes your personal files and the PC applications and returns 8 Windows to its original state. That the State of origin is a clean install of Windows 8, nor the default configuration of OEM factory, depending on the medium used for the operation. +

• Re: Satellite Pro L500-1VX-accessibility (FN key) does not work correctly

  I need your help to fix this problem on my Accessibility button does not work, when I press the FN key to turn my wireless on it does not work.
  When I go to program files > Toshiba > utilities > TACSPROP.exe a warning alert telling me it does not allow in this operating system.
  And for your information I have Windows 7 32 bit.

  If you are very popular to tell me what to do with this problem.

  Hello

  All the stuff for Win7 32 bit, you can find on the Toshiba support page in the download section > http://eu.computers.toshiba-europe.com > support & downloads.

  As Akuma written already install the most recent value package and check the functionality of the FN keys.
  Wireless network card is installed correctly?

• Satellite Pro A120: DVD/CD-RW drive does not work

  Hello: the dvd/CD-RW drive does not work. apparently it has been disabled somehow! Any ideas on how I can turn it back on?

  Have you tried the Device Manager and it says it works normally!

  Any ideas please?

  Thanks :)

  > apparently it has been disabled somehow
  I put t think that the disc has been disabled!

  How someone or something should turn off the drive? You have disabled the drive? I don't think so!

  You said that the drive appears in Device Manager. So I guess that the drive is enabled and is recognized by the OS.
  You are getting error messages or what's wrong?

  Perhaps the reader can read or burn CDs or DVDs.
  This happens if the lens of the drive cannot calibrate properly and can not handle the inserted media.

  Maybe the replacement drive is required!

• Satellite A300 - 1GN PASGCE - LED light button does not work with Win 7

  I improve my laptop for windows 7 everything works fine but the touchpad multimedia light led power button does not work.
  Play, stop, next work earlier but not the light / off does not work.

  No idea why?

  Hello

  Maybe it's a question of s a Win 7.
  I mean that the software is not intended for Win 7 but only for Vista.

  But you should check if you can reconfigure this button again.
  In Toshiba Assist-> optimize, you can find the Support of Toshiba Button tool.
  This tool can be used for the new configuration of the control buttons.

  First click on the button that you want to reconfigure and target path you can then choose the path to the exe file that must be executed by pressing this button.

  As far as I know that the exe files are placed in the program files/Toshiba/TSB folder.

  You will find different applications and one of these applications control the light on/off.

• Scanner does not work with Vista Windows Equium A210-171on

  I have a Toshiba equium laptop (Vista)
  I am wanting to buy a scanner so I can scan documents to computer. (I have an all-in - one but the scanner does not work)

  Please indicate where to go?

  Thank you

  Hi Suzanne,.

  Sorry, I Don t understand why you want to buy a new scanner. First of all, it would be nice if you tell us what satellite you have. Other useful information would be exactly, what does NOT work on your satellite and your 'all-in-one '...

  Please provide more information on this subject and maybe you shouldn't buy a new scanner.

  THX

• Windows Installer does not work with Vista Home Premium 32-bit system.

  My computer did not an automatic update in over 6 months.  I discovered this when I could not install my tax preparation software.  the error message is gone "windows installer does not work, a file may be damaged, contact support windows technique.»

  SFC

  Check the alteration of the file by clicking on Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type

  sfc/scannow
  

  For the results of the SFC
   
  Check the alteration of the file by clicking on Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type
   

  findstr/c: "[SR] cannot" %windir%\logs\cbs\cbs.log|more "

  The system update tool

  Ensures the consistency of the folder WinSxS (Side by Side).

  http://Windows.Microsoft.com/en-AU/Windows7/what-is-the-system-update-readiness-tool

  For 32-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=504

  For 64-bit Windows

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=1540

  To see the results click on Start - All Programs - Accessories - right click on command prompt and choose run as administrator. Type (or copy the below line and a line empty below and right click in the command prompt window and choose Paste).

  Notepad %SYSTEMROOT%\Logs\CBS\CheckSUR.log

  Reregister Windows install

  Desktop shortcuts are shortcuts to the Windows Installer which then starts the Office program.

  Click Start - all programs - Accessories - right click on command prompt and choose run as administrator. Type

  regsvr32 c:\Windows\System32\msi.dll
  regsvr32 c:\Windows\System32\msihnd.dll
  regsvr32 c:\Windows\System32\msimtf.dll
  regsvr32 c:\Windows\System32\msisip.dll
  c:\Windows\System32\Msiexec.exe/reg

  That you re-register Windows Installer.