Scan mode security 'sleep'

Similar Questions

• After scanning essentials security said my computer has not been scanned and it is not protected

  After that says security essentials scan my computer has not been digitized and is not protected. It is on a weekly auto scan and does not work. Why

  Hi Pat,

  Thanks for choosing Windows 8 and welcome to the Community Forums of Microsoft.

  According to the description provided, automatic scanning of Microsoft Security Essentials not happens on your computer.

  1. What is the operating system on your computer?
  2. you use security software?
  3. did you of recent changes to the computer?

  A possible reason for this problem is that you have installed entirely or partially on the PC security software conflict. Remove all other computer security software.

  Method 1:

  
  Uninstall program anti-virus and check if it helps.

  How to uninstall antivirus or antispyware programs?

  http://Windows.Microsoft.com/en-us/Windows/how-do-i-uninstall-antivirus-or-antispyware-programs

  Important: Antivirus software can help protect your computer against viruses and other security threats.

  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:

  1. to run, the PC must be on and connected to the internet (it cannot be stopped, "standby mode", hybrid sleep or Hibernate mode)
  2. saving settings must be such that the PC not to close or to go asleep during analysis.
  3 analyses do not begin precisely when demand - some may start earlier or later than the officially set time hour (according to Microsoft servers and charges at the time).

  You can also refer to the article mentioned below for more information.

  Microsoft Security Essentials - Installation Checklist and frequently asked Questions

  http://experts.Windows.com/w/experts_wiki/89.aspx

  If Microsoft Security Essentials problem or if you experience problems of Windows in the future, let us know and we would be happy to help you.

• My printer 3050 J610 goes in standby mode or sleep, and then I can't print docs it wireless

  Whenever I have don't print something for a few hours, my printer goes into sleep mode or sleep.  When it does, it can be used to print from my laptop or android for it.  Y at - it a way to put in place so that it doesn't "go to sleep", and it is always available for me to print with.  I like the printer, but it seems few off that you can't print on it wireless and it is considered as a wireless printer.  That's the only reason why I bought it and now I can't even use it without stepping down and turning the printer back again.  If I wanted to do this every time I was going to just print from my main computer!

  Thank you

  Ashley

  Well, I activated the incoming and outgoing settings under sharing files and printers in the firewall. I've also set up a connection between the router and the printer security rule. Since then, I was able to ping the router and the router by its IP number regularly for more than 72 hours. I hope that this solves the problem and everyone helps the dilemma.

  Mike

• Satellite A100-775 wake mode not sleep by call or fax

  "Nine" Satellite A100-775 (core 2 dual multiprocessor) wakes up mode not sleep by call or fax (ISDN Controller):
  AVM FRITZ! X USB with corresponding power management features).

  BIOS and software patches are up-to-date, motherboard already changed by Toshiba service.
  Devive Manager is no 'power management' tab of this network adapter. In addition, standby and hibernation work generally.

  On my Satellite 1110 everything works fine.
  What is a special problem with DC or something else?

  Post edited by: Kykladen

  Hi everyone out there!

  No idea of the outside world? It might be a problem with the State of the power to the laptop:
  Satellite goes to previous day "S3" so that my old laptop uses "S1". I tried - unsuccessfully - to force the
  "S1" to the level of the dumppo.exe utitilty and I am now using a Hubv (self powered) USB root 'active', but: zero. "."
  All the ideas in the world?

  Thank you!

  Hello

  Unfortunately I have no much experience with fax and I don't use AVM Fritz! X USB but I can you recommend to check the properties of the USB device and see if option called allow this device to wake the computer from the mode standby on the property power management dialog box in Device Manager is enabled.

• Could Scan mode and FPGA mode be used in a project?

  Hi all

  I need a project that the current NI9203 with mode of analysis samples and samples of the accelerometer of the NI 9237 with FPGA mode. It could be achieved? Could Scan mode and FPGA mode be used in a project?

  I use labview2009.

  Thank you very much.

  Yes, they can. This mode is called hybrid mode. To use the Mode of LabVIEW FPGA IO modules, simply slide the module to the target FPGA in the LabVIEW project, disconnected from scan mode. Then use LabVIEW FPGA to program the modules and use I/O variables for read and write I/O on the remaining modules. When you use a LabVIEW FPGA Mode on one or more modules, the logic of the scan Mode CompactRIO on the FPGA, known as the RIO Scan Interface, is compiled in a single application of FPGA with LabVIEW FPGA VI. If no module is configured to use the scan mode, the RIO Scan Interface is not included in the compilation.

• limitations with cRIO in Scan Mode

  Hello!

  I use a cRIO to get five channels of analog voltage in Scan Mode. I have three parallel Timed-while loops. When I use a 1ms dt, the vi does not run and cRIO is disconnected from the project (it is said that cRIO does not). When I use a 100ms dt vi works normally. But the acquisitions must be made with an interval of 1ms. The possibility exists to be a limitation of the Scan Mode?

  Thank you!

  The analytical engine should be able to manage the acquisitions 1ms, but make sure that you configure the engine to scan for 1ms period.  You can synchronize call analysis engine loops instead (it's one of the timed loop timing options).

  If you try to run 1ms loops and there are a lot of things in the loops, you may lose the connection with the cRIO because the thread that serves the TCP connections runs at a lower priority than call loops.  If the call loops all the time take processor, there is no time CPU to manage communication.  Do you need to process each sample as you receive it, or you can read data from each ms but more slowly process it in batches?  If you download your code, we can help you eliminate inefficient code that slows down your curls.

• How can I get channel z (zero) data encoder with a NEITHER-9411 in scan mode?

  Hello

  I use a cRIO to read a quadrature encoder, and I need z-Canel (zero channel) data using a NOR-9411 in scan mode.

  Chassis: NEITHER cRIO-9074

  Module C-series: 9411

  Encoder: EIB H25 series (model # XH25D-SS-1440-ABZC-28V/V-SM18)

  Now, I installed it using in scan mode and the properties > Configuration parameters of specialty as follows:

  Lifestyle specialty: Quadrature

  Input filter: disabled

  Time base of speed: 4096us

  Index Mode: Disabled

  This replaces Position0 position 1, Velocity0 and Velocity1 module instead of et0, DI1 channels, etc.  It works well to get a reading of the speed, but not the Z.

  I need to know Z as in the rest of my program calculations depend on.  (For this encoder Z is a digital signal that goes low when the encoder reaches 360 °.  It is also a very fast signal.  7200 RPM, it has a width of approximately 3.3us pulse.

  How can I get the data Z in Scan Mode?

  Agile Hello,

  The mode setting of index is the only way to access the Z channel in Scan Mode.  If selected the position will reset when the z channel is detected and the phase of the two other channels corresponds to your selection.

  It seems that you have the real z signal elsewhere in your code.  You may use the position data to generate the Z channel for this purpose?

  Let me know if you have any other questions,

  Sebastian

• Strange error with cRIO and scan Mode

  I'm scanning two modules cRIO on a controller of 9012 + 9112 bottom of basket 8 channels in scan mode, and I call the function 'read the Variable scanned '.

  I see this error, each a few scans:

  Error -2132869099 occurred at Property Node (arg 1) in PolymorphicModuleScan.vi:7->sampleData2.vi->ZDAQ_cRIO_Target_Main.vi
  
  Possible reason(s):
  
  LabVIEW:  (Hex 0x80DF0015) A deployment transaction is in progress.
  

  The search for this error on NI.com gives no help at all.  This is the first time I see this (I've been running this code for some time without error).  All software is since the dev of August 2011.

  Resolved: I was calling the function "Get the Period.VI of Scan" scan at 1 Hz.  This seems to have caused the 9205 (not the 9237) produce this error.

  I removed the call to the offending function and this has solved the problem,

• FPGA: R-series scan mode

  Available for PXI RT Systems FPGA scan Mode uses the R-series cards? Or you can use the Mode of the FPGA Interface to access the FPGA?

  Thank you

  Craig

  Scan mode interface cannot be used with the r series devices as far as I know, so you want to use the read/write and DMA FIFO nodes to communicate with the FPGA.

• Default sampling frequency NI9235/9236 equipment in scan mode.

  Hello

  I am currently using NI9235 with cRIO under scan mode, which allows sample rates up to 500 Hz. I realize that the card module has 12.8 MHz internal and under mode FPGA software and hardware time base combined anti-aliasing filter will be adjusted automatically depending on the installer of data rate, which is a set of values from 10 kHz to 794 Hz. Unfortunately, I do not have the FPGA package for now.

  My question is that what will be the flow of material data, if NI9235 the samples at 500 Hz in the scan mode. The anti-aliasing filter still works just below half the data rate material?

  Marco

  BMT WBM

  Hello Marco,.

  When it is used in scan mode the 9235 and 9236 are configured to sample at 10 KHz.  Unfortunately, this parameter is not configurable in scan mode.

  Let me know if you have any other questions.

  Sebastian

• Access 9236 shunt cal with scanning mode?

  How allow us calibration shunt with scanning on the module 9236 quarter bridge strain gasoline

  We are very happy with the release of Labview 2009 and RIO 3.2 because most of the cRIO modules now supported the scan mode.

  We want to use the interface in scan mode with the quarter bridge strain Guage 9236 module, but we must be able to access the features of Shunt calibration. With the FPGA interface, you acquire a set of data. Then allow you the shunt calibration and gain a second set of data. Then you compare the two to get to a scalar value using some equations. This eliminates lead resistance in your calculations, which can be less than ignorable in certain circumstances.

  Thank you

  It was easy. I just hung out and left down the constant IO then right mouse clicked on it and all its I/O write properties come. Very cool. All too easy to be crio programming, lol.

• Using the scan Mode 9411 cRIO-9074

  Hello

  I use an entrance Module differential differential NI9411 under cRIO-9074 with scan Mode, but I noticed that some problems are present.

  My application needs two encoder and we choose two incremental encoders with 1024pulses/rev. I have configured the NI9411 quadrature Mode, so I can read the position and speed of the encoder. Each shaft turn at different speeds.

  One of them can turn 4.6 rad/s as a maximum speed, while the other hit it up to 402 rad/s. Then, the configuration of the module input filter is set to 1microsed, the time base speed 32768 microseconds and the disabled index mode. These values make for a correct reading? The cRIO scanning speed is set to 1ms.

  On the other hand, watching the tutorials or (http://zone.ni.com/devzone/eda/tut/p/id/7109), that the degree of rotation depends on the encoding type, what type of encoding is used in Scan Mode? X 4?

  Using System Manager OR distributed, one of the encoders to read impulses sometimes sporadic (up to 2 digits) Although the encoder is stopped. However, the other bed is always 0. It seems that the encoder is broken, isn´t it?

  Thanks in advance for your comments

  Hi Juancar,

  I think that the values are suitable. The issue of reading 0 is explained in this KB:

  http://digital.NI.com/public.nsf/allkb/C9088DFDF803CD8B862575F3007C40FD?OpenDocument

  In addition, according to this document:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/7338

  decoding type must be set to X 4.

  I hope this helps! Suerte con ello.

  Jesus

• scanning mode of scanning screen. Cannot change the option of transparency-postive.

  Hi, I need help please, I have a hp photosmart c7180 while a printer and scanner, OS mavricks 10.9.3 when scanning window opens it says waiting for scanner, the screen flashes to another screen with a sidebar on the side right which has the following options. Scan mode; Kind; colors; Resolution; Size; Scanning; Name; Format; Image correction; Adapaptive lighting. Sharpen. "" I can not change the transparency-Postive scan mode or any other function in the sidebar, at the top of the screen displays a box of ' Scanner reported an error ' and the beach ball is everything. The only way to get rid of this is to force quit the printer. I also tried to restart and download the latest patch printer but every time that you open the option scan the same things happen more. any help with this problem would be great.

  jm44

  Hi Sunshyn 2005,

  We thank you for your email on how to reinstall and and remove the printer and repair disk permissions. I carried out all the instructions in your email and kept happening the same thing, so I thought to what might solve this problem? then the answer came to me, that would fit the tray of slides (with slides) and remove the white plate then allowing the transparency-postive option to be changed again flat. If you don't analyze a transparency it won't let you change it back flat. I want to say thank you for the help with the matter and I hope that this email explains what went wrong.

  Thanks a lot for your help.

  jm44

• read the temperature of the chassis of a cRIO in Scan Mode?

  I am trying to create a section for monitoring my VI which monitors the status of the cRIO 9022 and backplane (9104) I use. I understood how monitor memory, CPU utilization, and the input power voltage.

  I know that you can monitor the temperature of the chassis using the FPGA options, but I want to keep my cRIO in Scan mode. Is it possible to access the scan mode chassis temperature probe?

  I found the solution I was looking for. NOR has built a VI to get the temperature of the cRIO, but it's not easy to find or in the open air.

  It is located here:

  c:\Program Files\LabVIEW 8.6\examples\CompactRIO\Controller Specific\9022 voltage and temperature Monitor\cRIO-902 x Support files

  "The cRIO-902 x Support Files" is a library that contains 2 VI is used for the sub - VI voltage monitor, and a third VI called "get Council Temperature.vi.

  Drop in the cRIO app and the Vi shows the temperature of the CPU cRIO in ° C card.

• CPU temp is-128C after the resumption of the mode S3 Sleep

  Hello

  As says my title, my temp cpu bed-128 C after waking mode S3 sleep.

  This affects my fan control, and while not particularly dangerous, it is annoying as my fans are set to 100% and do not return to their modes of thermal cruise.

  However, when I restart my computer temperature readings are fine and the fans run in accordance with their respective temperature readings.

  The really weird thing is that as I get S3, I look at the temperature of my cpu and it reads 40 c (same as idle temperature), but this only lasts for about a second how the temperature reading goes up to C - 128, while my fans are working up to 100%, such as fans and temperature readings are pegged to their "extreme" until I restart the computer.

  I tried to close the temperature monitor and re run after S3 wake up without result. I also tried to launch a processor intensive task to see if that would record at least a change in temperature, also without success, the temperature reading remains pegged to c - 128.  Is it possible to correct the stray cpu temperature read during his awakening of S3, because it seems that the sleep mode S3 everything resets all leaving the cpu temperature sensors in limbo?

  Im running:

  Win Xp pro SP3 and Speedfan 4.45 (temperature monitor)

  2 GB of ram

  T8300 CPU @ 2.4 Ghz

  Card mother MS-9803 w/FRIEND BIOS 2.2

  O.K.

  After combing through the net re: the above question, I determined that the problem I see with the temperature monitor is only a superficial, but light always news, of a larger problem.

  I contacted the mfr of cpu and my cpu temperature is within specifications, even after the release of the S3 despite what said Speedfan.

  So the problem I have is not so much with the temperature of the cpu that the fact that my cpu is "spinning its wheels" after the exit of the S3 with cpu common use anywhere from 15 to 35% (via the Task Manager) with no visibly active application/process. .... IM thinking to start a new thread and the closure of it.