Screen flashes on then off quickly when it is locked and you press the power button / stop?

Similar Questions

• PowerEdge T410 won't do anything when you press the power button / stop.

  My work has recently retired this t410 server. It worked without any problems when he was arrested. I had to remove and destroy the hard drives from the system. After that, I was allowed to bring home for my own use. I installed a new sata drive and plugged into the power supply and a free sata port on the motherboard. I get nothing when I tried to boot the system. This version has the unique power. Power light only lights up when you press the test button. System fan is going at full speed, but stops when you release the power button. Also on the control panel lights 1,2 and 4 and HDD power on and turn until the test button is released. There is a single green light lit on the motherboard, while it is plugged. Apart from that, I have no response when you press the main power button. Can anyone tell how to try to get it up and running again.

  -Who-

  I have not received the answers more so I think that this issue is ignored. So I'll let everyone know what finally happened. I solved my problem after a lot of electrical testing. I found a diagram of the arrangement of the power dell power supply pins and I made myself the best possible meter test. After several rounds of tests, I found several pins that did not have the right voltage. I bought a new power supply. I installed and replace everything. I plugged into the system and it auto fed on itself. I loaded from an OS and it works perfectly.

  Problem solved

• Why Satellite Pro A300 does not start when you press the power button?

  Suddenly my new Satellite Pro A300 does not start correctly when you press the power button. The situation is the following: when I press the power button is displayed the opening of Toshiba (Leading Innovation) and the disappers image quickly. Then there is a black screen for about 30 seconds. There is a rectangular frame with the text Microsoft Corporation under. And nothing happens however long wait.

  In order to get with the trial starting I then shut down the computer by pressing the power button until the computer turns off. ("The hard way to close")
  Now, I press the power button shortly to turn on the computer. Then, the computer starts normally with the photo to open Toshiba and after a few seconds, I wonder to open the computer in safe mode or in normal mode. I now choose to open in normal mode and the computer opens normally and is ready to work.

  What should I do to get a normal departure procedure?

  When the laptop starts normally (after choosing normal mode) stop your laptop properly using START > shut down option. Next launch should be normal.

  When the OS is moving towards the low irregularly will always ask you how to start this new (secure or normal mode).
  The same thing happen on my Satellite A300.

• PC does not start when you press the power button, after that starts automatically as a ghost!

  I have HP Pavilion a6030in, my pc does not start when I press the power button / stop ther, but she starts automatically after some time after that, it works fine.

  Even once when I closed and leave it for a while and still the problem is not resolved.

  Help, please

  I solved the problem

• My his laptop makes a beep when I press the power button / stop and it does not start

  Hello

  I bought a new Dell Inspiron 15z touch ultrabook and when I pressed the power button, it starts to beep and won't start. The screen is totally blank. What should do? Help, please

  -Mayur gala

  Hi Mayur,

  Welcome to the community,

  Sound signal can be used as a diagnostic indicator. The computer may emit a series of beeps at startup if errors or problems. This series of beeps identifies a problem and is called "beep code".

  See the table below which shows the beep codes and the possible problem:

  Overview of beep Code
  Beeps	Description	Possible cause
  1	ROM BIOS checksum failure	The map system, covers BIOS corruption or errors ROM failure
  2	No memory (RAM) detected	Memory or memory slot failure
  3	Chipset error (North and South Bridge error) Time-Of-Day Clock test failure Gate A20 failure Super i/o chip failure Keyboard controller failure	System board failure
  4	Memory read / write failure	Memory failure
  5	Real Time Clock (RTC) power failure	CMOS battery failure
  6	Video BIOS	Video/smart card failure
  7	Failure of the CPU	Processor failure
  8	LCD SCREEN	Failure of the LCD

  Let me know if you need assistance.

  Thank you

• Tecra A4 does not light when you press the power button

  When I press the power on button it turns green for 4/5 seconds then turns off.
  "I do all the tests the support on the page:
  
  * Press on and press and hold the Fn key and press the F5 key repeatedly. If an image appears on the display, this indicates that the image has been activated to a connector for a monitor outside, causing only appear to be off the computer.

  * Connect the adapter to the computer.

  * Remove the battery and unplug the AC adapter and then connect only the AC adapter. Make sure that the power adapter is one that comes with the computer. Try to turn on the computer again, without the battery in the computer.

  * Plug the power adapter into a different plug.

  * The battery, ensure that there are enough energy to start the computer.

  * Press and hold the power switch for 10 seconds (to make sure that the computer is turned off). Wait five seconds, and then tap on and again, hold the switch for three seconds (turn on the computer).

  * Ensure that nothing beats (a sliding plastic cover) in the path by pressing the power switch.

  * Disconnect all devices (printers, pointing devices, keyboards, etc.) connected to one of the ports on the computer.

  * Remove any additional memory, beyond the computer built in memory, or the first module of memory in the computer. If the computer starts correctly, reinsert the memory and turn the computer back on. If it does not start successfully, memory can be inserted incorrectly, it may be defective or the support of memory may be damaged. "Try to replace the module memory."
  In vain:]

  You know? THX

  Hello

  There must be a hardware malfunction.
  You have tested a lot and nothing has worked
  I think there is not much to do, you all tired and I guess the authorized service provider could help you

  If your warranty is valid all should be done for free, so don t you worry and ask the experts ;)

• HP DV6 6115TX UP STARTS NOT WHEN I PRESS THE POWER BUTTON / STOP NOTING HAPPENS

  LAPTOP: HP DV6 6115TX

  1. WITH THE BATTERY AND CONNECTED AC-

  WHEN I PRESS POWER BUTTON NOTHING HAPPNS ONLY INDICATOR LIGHT NEAR THE POWER SUPPLY BECOMES WHITE AND STAYS ON UNTIL I HAVE TO REMOVE THE BATTERY.

  2. WITH THE BATTERY ONLY

  WHEN I PRESS POWER BUTTON NOTHING HAPPNS ONLY INDICATOR LIGHT NEAR THE POWER SUPPLY BECOMES WHITE AND STAYS ON UNTIL I HAVE TO REMOVE THE BATTERY.

  Hello @HPDV6-6115TX ,.

  Welcome to the HP Forums!

  I understand that you laptop is not turning on.

  If the laptop has no power, other than the AC adapter connection indication, there is little that can be done.

  The adapter ring is HQ shows a white LED would suggest the adapter supply fine and offer pay-per-view mother, or at least the internal power connector. This means it is a flaw in the motherboard of the laptop and most likely requires a repair.

  You will want to check that the RAM and HARD drive are in place and connected, as well as internal power cable. You can do it by following your product Maintenance & Service Guide.

  HARD drive: Page 62.

  RAM: Page 66.

  Power cable: Page 83.

  If it does not, you will need to contact the HP support by phone for service options. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.

  Hope this helps!

• Two Macbook Pro, both does not start up, when I press the power button, I hear two disc bit Caryl, I see little light on the front on the displasy release button, black screen, no edge

  It was weird because I've NEVER had two computers have the same problem before. They are the model 2008 2.2 Ghz Core 2 Duo, 6 g of RAM, models of 128 GB of hard drive, the two Yosemite running, both had new hard drives, cables, batteries and RAM installed OWC (Apple approved reseller) and I use Macs for at least 20 years. In about a week, one just blacked out while sitting on my desk doing nothing, the other does the same on a week later. When I press the power button, I hear the drive hard hum twice, then all I get is the little light on the screen release button, that's all. Black screen. fails, nothing. I can press the power button and it will fit off the coast. Is it possible that some of them have infected somehow, or possibly send me the malware that has infected my system? I would not normally only, but for all of them to go down to one right after the other with the same problem just made me think, it must be the same cause, but what?  I had been in a war of fire recently with very ugly people, and I've never seen two Macs have the same exact problem in a row like that right.

  I took readers on the Macbook Pro, put them on sleds and threw them in my PowerMac, and both seemed fine, no problem, started well upward, ran utility disk on them, no problem, so I started to the checklist. Reset the PRAM. Nothing. SHIFT key at startup. Nothing. D at the start. Nothing. V order at startup. nothing. I wouldn't mind even their evisceration and making a portable useful with the parts of the two, but until I find out what the problem is, what can I do?

  If anyone has any suggestions, I would really appreciate it, I've supported every button I can think at the start, tried an inch USB key, boot and disk, this is the same Caryl bit both of the car, no chime, black screen, that's all.

  Thanks for your help.

  Damicon999 wrote:

  Is \Is possible for someone they have infected somehow, or possibly send me the malware that has infected my system?

  no chime, black screen, that's all.

  I don't think they are infected.

  The startup chime indicates that the Mac has made the initial diagnostic tests and there is no hardware problems or fundamental software.

  No edge in your case is a problem.  I think it's the luck of the draw to have 2 failures.

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• Compaq 6710 b: my HP Compaq power on only when I plug in power. Don't turn on with the power button / stop!

  I have a laptop HP Compaq 6710 b... Its more than 6 years...

  The problem is really annoying... The laptop powers on only when I force taken into the spindle of the charger and the laptop works very well after that...
  But the laptop never turns on when I try to power by pressing the power button!
  I did not understand the reason why...

  Any thoughts on this problem?  Help!

  There are no settings in the BIOS that affect the use of the power button.

  The power button works at the level of the material (firmware).

  By pressing the button translates the action of the Commission of the conditions of the logic system.  There must be voltage at specific points in the power circuit. If the voltages are not present, then the power button does not work. This can be caused by a failure resistance, mlcc capacitor or a bad solder joint, if the power button has been tested and shown to work normally. Fluff even could cause this to happen. This can help out-performed by Visual inspection and using a multimeter.

• When my computer goes into sleep mode, I have to press the power button to turn it back on.

  original title: sleep/hibernation

  When my computer goes into sleep mode, I have to press the power button to turn it back on.  I used only having to press a key on the keyboard.

  Can someone tell me how to solve this problem, as if it was before?

  Well, on the theory that your computer is awkward, try to change the settings to another thing and OK your way out the control panel.  Then go back and put them in the way they were and OK your way out.  Occasionally, it will reset the internal parameters and things can return to normal.

  HTH,
  JW

• Dell PC randomly freezes and now require the power button to turn off

  original title: PC freezing

  My old DellPC of 11 months has started to freeze. Use the power button / stop to turn off. Once it will not re-start twice it turned off my Mcafee security.

  1. Uninstall Mcafee. Install something else like program AV from Microsoft.

  2. start in safe mode / networking. Install the Microsoft AV program, update, then scan the entire hard drive

• all in a single j6480 won't turn on or off by pressing the power button

  my all in one j6480 won't turn on or off by pressing the power button. from pluging in the power cable to the output, the display panel stays on by a flashing point moving from left to right, repeatedly. also, there is a faded beeps coming from the printer on the left side. See no empty self am unable to do anything on this subject.

  There may be a problem with the power supply/power cord module brick.  Try following the steps described in this document.  If that does not receive the printer works properly again, you can try to contact tech support to buy a new power module (if still available), or you need to replace the printer.  You can join the 1-800-474-6836 technical support to the United States and the Canada International users click here.  Let me know what happens.

• Hello, when installing Adobe Creative cloud, you get the error: program stopped working "Adobe Creative Cloud" Windows can check online for a solution to fix this error on the Internet. The next step is really for a solution online

  Hello, when installing Adobe Creative cloud, you get the error: program stopped working "Adobe Creative Cloud" Windows can check online for a solution to fix this error on the Internet. The next step really is to get an online solution and close the program, close the program. Signature of the problem:

  Problem event name: BEX

  Application name: Cloud.exe Creative

  Application version: 3.4.3.189

  The timestamp of the application: a 56702, 75

  The name of the module with the error: StackHash_0a9e

  Version of the module with the error: 0.0.0.0

  The module of time with error stamp: 00000000

  The exception of compensation: 00000000

  Exception code: c0000005

  Exception data: 00000008

  OS version: 6.1.7601.2.1.0.768.2

  Language code: 1049

  Additional information 1: 0a9e

  More information 2: 0a9e372d3b4ad19135b953a78882e789

  Additional information 3: 0a9e

  Additional information 4: 0a9e372d3b4ad19135b953a78882e789

  
  

  uninstall all cc on your computer.

  clean a http://www.adobe.com/support/contact/cscleanertool.html

  Restart your computer

  suspend your antivirus/antimalware

  Right-click on the file to install the desktop application, and then click "Run as Administrator".

• Windows XP will not be closed. I have to press the power button to turn it off.

  original title: WINDOWS XP WONT SHUT DOWN - I HAVE power to the BOTTOM BY pressing POWER BUTTON COMPUTER

  WINDOWS XP DOES NOT - STOP I HAVE TO POWER COMPUTER DOWN BY PRESSING THE POWER BUTTON

  I had a computer that had posted these symptoms.

  In the end, I did the following:

  1. in Control Panel, "Power Options."

  2. click on the "tab APM" " ".»

  3. check "Enable Advanced Power Management Support"

  4. click on OK

  Check the result.

  Reference: http://support.microsoft.com/kb/313290

  Hope this helps

  Post back if necessary

  ________________________________________________________

  If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• A font I need is not available in italics. Corel Paint Shop Pro produces the police in italics when you press the Italic button in the software, but I don't see any way to do this in Illustrator. Help, please.

  A font I need is not available in italics. Corel Paint Shop Pro produces the police in italics when you press the Italic button in the software, but I don't see any way to do this in Illustrator. Help, please.

  Select the text and use the Warp tool to give a fake italic.