SD2008 - Port 3 dead

Similar Questions

• Satellite Pro C650 - USB ports now DEAD

  Over the past 48 hours have really struggled to get my USB ports work,
  Toshiba SATELLITE PRO C650 lappy running W7... At only 2 usb ports.

  A couple of days, I bought a new stick of memory... 16 GB SanDisk Cruzer Blade... He stuck in lappy and anything that happened outside my mouse attached wireless stopped working.
  Since then, the ports were completely dead. (stick now appears on anotherPC)
  That's what I did so far, after a search web solutions thro...

  Device Manager display ports everything is OK with no exclamations...
  When I insert any USB device... no sound confirmation of PC and Dev Mgr flinch...
  Tried to uninstall port/hubs and leaving W7 re-install them using... Still dead...
  Trying to remove battery and power sector during the centuries, then re start off the power... Still dead...

  I think that my last resort looking for a factory system by default re install... but one have a mountain of things astro which must be saved and cannot be done through many many discs.
  I really want to be sure ive tried everything before you do this.

  Could I have really damaged the MB. ??
  I now nowhere so fast if theres anyone out there has any suggestions please shout...

  > I think that my last resort looking for a factory system by default re install... but one have a mountain of things astro which must be saved and cannot be done through many many discs

  Even if it s really painful to get everything installed it again, I would recommend to recover the laptop using the Toshiba recovery disc or HARD drive recovery.

  > Could I have really damaged the MB. ??
  Well, it's hard to say before trying the recovery procedure.
  If the USB ports are not working after using the recovery disk (or HDD recovery), then of course: the mobo may be affected, therefore, in my view, the laptop must be set to the factory settings.

• WRT160N V2 physical ports seem to be dead... * beep *.

  I got this router installed in my home network for about a year.  The firmware is updated.  Brief description of the home network:

  Comcast Cable Modem

  WRT160N v2

  2 wireless laptops connected to the router

  HP Business Inkjet wireless connected to the router

  1 iMac hard wired (or wireless) to the router

  1 NAS200 hard wired to the router

  1 Epson printer connected to PSUS4 connected to the router

  Sunday night while he was working on the mac, I got a message that I lost the internet connection. I tried powercycling the modem and the router, no change.  I can't connect to the modem (192.168.1.1) of the Mac when connected to the router hard.  If I turn on the wireless on the mac, or use a laptop computer connected wireless, I can connect to 192.168.1.1.  When I do, none of the wired devices appear in the table of network. The Modem is connected to the router, but not connected (DHCP 0.0.0.0) and there is no internet connectivity. If I connect a computer directly to the modem cable, there is a link and it works fine.

  Any troubleshooting I can do, it seems that the physical ports are dead.

  Explanations, or suggestions would be appreciated.

  Justin

  Time to reset the router and reconfigure.  Press and hold the button of reset for 30 seconds and then release.  Wait 30 seconds and now the router power cycle.  Disconnect the modem for now.   Connect to the router via a computer wired to 192.168.1.1 with empty user name, admin password.  Now, reconfigure the router back to your configuration.

• USB ports not working not not on Satellite Pro C650 - 18 d

  Hello
  I have a Satellite Pro C650 - 18 d on which USB ports are dead.
  So far, I've updated the chipset and BIOS - but they stay dead. It doesn't seem to be a power either. I have a USB key with LED and it does not light.

  Any ideas? It's under warranty and so unable to try something wild!

  Thanks for any help
  Jim

  Hi Jim

  I recommend you to reinstall the OS and test the feature with the factory settings. Please, test it with several different USB devices. If none of them works, you must contact the Toshiba service provider in your country and leave check s portable.

  Do you know how to find the addresses and phone numbers?

• Toshiba Canvio 5 TB carving UBS ports

  Hi, I bought this unit two weeks ago and I have a real problem with an intermittent fault. I tried to reduce the issue down as much as possible, but just when I thought that I solved it, he did it again.

  Basically I use the drive as my storage drive for synchronization of the box, 360cloud, onedrive, drobbox, google reader and the location for my portal for recorded tv and plex media storage. And my system backups.
  Things seem to start but then as soon as Acronis True Image 2015 runs to back up my system, it starts but little time after 15-25mins (this cut just one out to 11.27 GB) in the backup, the USB port will cancel followed by my usb port mouse, my dongle wifi port.
  I checked the power management settings and they are not to disable usb ports when it is idle, hhds etc will not be closed after x time being idle. I ran acronis true image with all my cloud storage synchronization off, plex and media extender Portal off the power. I even stopped things as process lasso and kerish doctor and my internet security off, but he always does.
  I tried on windows 8.1 and windows 10 and its does on both and also tried on a windows xp laptop. On the xp laptop, it has not cut off the ports, but he could have done if used for more.
  After a short time, a few minutes after closed ports it tells me that the last device that I have connected malfunctions, but he does not recognize the USB so cannot reload the reader, each time I have to restart the computer, which is not very sure that without the usb ports, I have no mouse or keyboard to restart windows without using the reset button on the case! Even if I remove the devices and then reinsert them ports seem dead, nothing is picked up until I restart the machine.

  Without the drive connected everything works fine if its something to do with the drive

  I'm stuck. I need this sorting ASAP because I need to access the files I put on the disk regularly.

  I hope that there is an easy fix as the drive back would be very embarrassing that I need the data off the drive before it is replaced and I don't have another drive to do.

  I think it might be a problem with the power supply of the USB port...

  The USB 2.0 port common provides only 500mA

  The USB 3.0 device needs 900mA

  That's why I recommend you this HARD disk to connect to two USB 2.0 ports using the USB Y cable

• Satellite Pro C850-19W got a USB port broken in 2 days only

  Just got my new laptop and tried to install all my programs and move all my old files from my other laptop for two days.
  He was works well, I left it and when I woke it standby mode, the mouse connected to this USB port is on but does not. The mouse works fine in the other 2 USB ports...
  I have two USB 2.0 ports and a USB 3.0 on this machine, and the USB port which is placed in the left side next to the power connector has stopped working.
  It has the power it turns on Microsoft's USB mouse which has been connected since the first start, but it will not accept any communication at all.

  I rebooted in safe mode, uninstalled all the USB controllers and restarted, advice, I found here in the forum, but the USB port remains dead.
  Looks like this is a question with many Toshiba laptops and not even sure, I want it to be more I m.

  What to do now?

  > There since she lights the mouse Microsoft USB which has been connected since the first start, but it will not accept any communication at all.
  Have you tested the feature with another device like USB key?

• R7000 WAN Port does not use LAN as a substitute?

  I have a problem with my R7000. The WAN port is dead. I used it in access point mode for some time connected to one of my LAN ports, but I need to go back to a main router. Is it possible to run it in router mode outside of a LAN port, or I'm out of options and need to replace the router? Past the WAN port, everything works fine. Thank you!

  Ive never used Merlin, but I think you need to activate the dual WAN mode and just use the secondary interface for your main WAN while leaving the other disconnected.

• Front USB Ports suddenly inoperative

  I installed an SSD as drive 0 and moved the former player to Player 1. In doing so, I can have disconnected something because now my front USB ports are dead.

  Can someone tell me what controls the front USB ports or where I can get a diagram of the motherboard for the 8700-1262 XPS?

  Thank you.

  It is located in the owner's manual on the link below, download it and go to page 13 0f the PDF document

  www.Dell.com/.../manuals

• NB100 no usb not power - how to reset

  The NB 100 has 2 usb ports on the right side. I tried plugging in an external cd drive and got a box with red indicator of the background task bar indicating something on the device of drawing too much power and that the supply would be stopped.
  Since then the usb ports 'appear' dead. Nothing I plug is recognized by the NB100.

  It is said in the user's manual if it is found an overload of the power to the usb ports can be stopped. However, it does not say how to reset ports IE power to 'em.

  The card reader and the usb port on the left front work yet.

  I tried the update of the BIOS to the latest 2.10, affecting all the parameters of the default bios with F2 at startup and even bought "Device Driver" to make sure that all drivers are up-to-date.

  Can anyone help? I don't know there is a simple answer but just don't see it.

  Ideally, I would like to avoid having to reinstall XP because I do not have the disk and the hard disk does not appear to have a XP partition.

  Help!

  Hello

  In your case, I recommend to remove the /hub of /controller of the USB port on the Device Manager.
  Simply go to the Device Manager, expand the area of USB controller and remove all the devices that are available in this area.

  After restarting again, the system (Win XP in your case) should recognize the USB ports and the driver must be installed again.
  Then restart once again connect a USB device and check if it can help

  Just for info: USB 2.0 ports provide 500mA so in some cases the external USB device would not detected when this device would need more than the usual 500mA. In this case this device must be connected to two USB ports using a USB Y cable or use an external power supply, as do some USB hubs.

• Problems with connecting fiber and new router AirPort

  I installed the fiber optic connection to replace my cable modem connection... I have a network of airport for a long time. When I bridge router ISP in my airport network that there are multiple problems. The major is that when you plug the ethernet cable from the modem ISP Ethernet port on the WAN of Timecapsule port all the TC LAN ports go dead. (the ISP's modem has already a cable ethernet in the WAN port or the first port that comes from the optical network Terminal that the fiber optic cable to connect from the outside). I talked to the ISP and they say just use any ethernet port to connect to the WAN port on the TC. On their end, they say everything is connected and works... then it's the Apple... I bought a new TC and changed my ethernet cables, but all I can establish is a wireless network. My network is itinerant and all of my extremes are connected with cables, but all on my main TC LAN ports are dead. I rebuilt my network and the same problem... And I think that the culprit is ports LAN TC is off

  Unfortunately, Apple has designed their routers airport to work with a standard cable and DSL type connections. The fiber is a whole new game ball, and Apple has not yet learned the rules of the game, so you may or may not have a really hard question.

  When you plug the ethernet cable from the modem ISP Ethernet port on the WAN of Timecapsule port all the TC LAN ports go dead.

  Before you connected to the fiber "modem" Time Capsule, did first reset you back to default settings... and then... set up again I hope to work with the fiber optic router?

  If this isn't the case, you need to do whenever you change providers or the modem that the Time Capsule connects to.

  All other devices that might be connected to the time Capsule should be turned off and unplugged.

  Then, if the time Capsule can be configured to work with the "modem" fiber, you can connect devices to the time Capsule one at a time to ensure that each of them is working before connect you to the other.  It may be necessary to reconfigure some or all devices that are connected to the time Capsule so that everything works again.

  Bottom line here... get the time Capsule working first with the "to modem" fibers.  Then start to add other devices to time Capsule one at a time.

• Motherboard for Satellite L100

  Hi, I noticed that the slot PCMCIA and USB of my laptop Toshiba Satellite L100 (PSLAOL - OOUOOE), the ports are dead and the technician of the store where I bought the laptop told me that I have to change the motherboard to Gets the PCMCIA and USB is working again.

  Anyone know where I can find information on my laptop motherboard and its price also?

  Thank you.

  Hello

  How old is your laptop? The warranty is still valid? If yes contact Asp in your country. I hope that you will get new replacement motherboard for free.

• Qosmio F20-110: Microphone no function and issues with webcam

  Hello
  I have a qosmio F20-110
  recently I bought a headset (logitech) and a webcam (HP), currently problems with both
  so far, only one camera was periodically turned off and messengers could not recognize him, but just before that she worked
  for example, on Skype after a period of time (different) error message is displayed and the cam went, Skype also down reconnection to Skype, I it is said the cam can be identified on computer or used by something else (which is not true)
  Cam back only after I restart the computer

  now, the microphone does not work
  I tried the headphones on another laptop - everything works perfectly
  Currently, my laptop does not recognize the microphone, Te, I can't set the mic, it's just that the port is dead
  but the couple Twitter.com that it did not work properly

  Please help, if you need more information made me know

  OK, I'm back from the microphone by following the instructions of Skype - http://www.skype.com/help/guides/soundsetup_xp.html
  Cam is also trying, but I don't know for how long

  Please help with the problem with the webcam described above

• HP C5230: Scanner does not see memory cards

  I have a HP C5230 scanner, copier, printer.   It worked fine, but suddenly, it no longer reads any type of memory card.  Unfortunately, you have the scan to a memory card, so now the scanner does not work.  Anyone have any ideas?   It's like memory card ports are dead.

  Hi @niklasmama,

  Here are the directions to make a scan from the printer to a computer I found in the HP Photosmart C5200 User Guide.

  

  If the scan from the printer to the computer is not working properly, there is a problem with the drivers and the printer software.

  What operating system your computer is running?

  I'll watch for your reply, so I can help you further. Just reply to your convenience.

  Thank you!

• I also need the BIOS A8M2N - THE (Naos GL-6) 3.0

  Hello

  I have a SR2030NX.  After all of my USB ports and card readers slots failed, I also wrong improved BIOS (A8M2N - Naos GL - 6 mb) version 3.10 in an effort to try to repair ports - and then try to fix the video by uninstalling and installing the Nvidia chipset and video drivers. Now, my screen remains black, until XP starts.  I would like to bring back the BIOS to the original version, if someone could send me please the instructions and the file/s.

  I'd appreciate also all the advice on getting the key USB ports working again.  I tried to update the drivers and hub controller, but I see only an "unknown" device in Device Manager and all USB and card reader ports are dead. I put two USB PCI cards in based on and can live without the built-in USB ports and card readers, but I want to be able to get the BIOS mode without fail if/when necessary.

  Thank you in advance.

  Message edited by jnoelflma on 05/28/2009 14:32

  Thank you for your help. I already tried all the latest video drivers and chipset from Nvidia, but I think that the problem is related to my flashing a bad BIOS update, which made me lose my monitor in the startup of the computer.

  I downloaded the BIOS version original 3.0 since a link provided on this forum (thanks again) and hope for the flash back of 3.1 this weekend.  I learned this correction in the Hardware forum, where people have problems because they have wrong improved their A8M2N - LA, Naos GL-6 BIOS to version 3.1 hardly similar with monitor lost when starting out upward. This MB only works with version 3.0 of the BIOS.

• TC - 705 crashed. does not start. error message

  My sucks TC-705 crashed.  It does not start.  error message saying lack driver DVD player.  At the beginning I was not too worried because my recovery is on a USB key.  He went through the installation process, but the re-boot did it again.  Endless loop.  I tried all repair options without success.  I went to the command prompt and run the scan and repair.  Scanned very well, she could not make the repairs.  If nothing worked the hard drive may be damaged, said a source online.  I put a new disc in, but there was no improvement.

  Where should I go from here?

  Ironfly,

  I downloaded vanilla but after I extracted it I could not make heads or tails of it.  The Readme went on and on the forums running with it but not said me something about how to launch it.  I have a question on how to launch online, but the first statement, I had was to open my WOW file.  I knew then that I had wandered in some elses universe.  After reading more later, I realized that he was playing.

  All of this is moot right now because my DVD drive and all my usb ports are dead.  There is nowhere where ever I go except in the bios.

  At this point, I don't think that there is nothing I can do.  The computer is still under warranty and I have a one year protection plan so I'll let Newegg and Acer deal with reclamation.

  I wish I could give you a hundred Bravo for all your efforts.  Thank you and all those who participated.

  unktim