Separate the VLAN for CAPWAP

Similar Questions

• separate the vlan for the service console and vkernel

  Hi all

  I need to restructure my environment uat and dev, keeping both under vcenter even. I run the machine with 4 NICs (currently using 2 each for sc + vk & vm port with eather channel gp). The reason behind this is that we have stored separately (using nfs) in uat and dev segment to be used by the servers (virtual and physical) in the respective segment. I'll take 2 clusters as uat and dev. wanted to help the same regardeing

  • wanted to know if I can get my service console and vmkernel running on VLANs separate as shown below
    • UAT cluster
      • SC - 10.10.11.x
      • VK - 10.10.12.x
    • dev cluster
      • SC - 10.10.11.x
      • VK - 10.10.50.x

  kindly let me know for further information on above, any other suggestion on above will be useful

  Yes your SC and VMkernel networks running on different VLANS will work - it is a best practice.

• How to configure the VLAN for Cisco SG500 - switch 28

  Hello

  First of all, it's my first post here, I hope that someone can help me and please be patient because I am very little known.

  OK, so let me explain to you the scénarion I face and I hope someone can help me.

  We have a Cisco SG500 - 28 port gigabit switch in our workplace.

  Our goal is to create 3 VLANs and separate networks between the various departments.

  Vlan1 (which is the default VLAN in the switch)-will be used for the COMPUTER service and management.

  VLAN100 - will be used for business.

  VLAN200 - will be used for clients who need to connect to internet via WiFi.

  I created VLAN100 and VLAN200, and VLAN1 is there by default.

  I want to use port 13 for VLAN200 and to connect the-Wifi access point there.

  The uplink is in port 25.

  I would be happy if you could explain things first to a more general, abstract level, and then we can look at the specific scenario that we have.

  SG500 Cisco - 28 Gets a Sophos UTM 9 router internet.

  I need to take care of the inter - VLAN routing so, subnet and DHCP

  Thanks in advance,

  Sincere greetings,

  D

  Hi Desmond, looking at this DHCP pool it looks correct.

  For the second part, you waant VLAN 200 only work on VLAN 200, that's fine. So if you have an access point, and everything on the VLAN 200 connects to the access point, you can make an access to this list. The access list is entered only, which means the inbound interface.

  So if you have a gateway connecting to #1 port. You'll need to build the access list and apply it to port number 1. That's assuming you make a list of access 'decline' subnet source IP of VLAN 200 destined for the other subnet, that you do not want access.

  The image on another post to fill out your reference numbers, then for the ACL link, it should be placed on the interface VLAN 200 first comes to the switch (IE, the port the access point connects, make sure that you choose to bind by port instead of per VLAN)

  -Tom
  Please mark replied messages useful
  http://blogs.Cisco.com/smallbusiness/

• Change of ISE of the VLAN for wireless settings

  Hello

  I configured on ISE posture strategy for posture compliant and noncompliant to endpoints, such that endpoints compliant posture will fall in VLAN clean and not conform will fall in others.

  Now, my question is, even if an end point is consistent, it is not in VLAN own posture. To get the ip address of VLAN, it requires enough ipconfig and ipconfig / renew to do manually.

  How to solve the problem...

  Kind regards

  Aditya

  If you assign a VLAN, the final step for the PC client to renew its IP address. This step is performed by the portal of reviews for Windows clients. If you have not defined a VLAN for the 2nd AUTH rule earlier, you can skip this step.

  If you have assigned a VLAN, complete the following steps to enable the renewal of the IP:

  1. Click Administration, and then click comments.
  2. Click settings.
  3. Expand comments, and then expand Configuration multi-portail.
  4. Click DefaultGuestPortal or the name of a custom portal that you created.
  5. Click the DHCP Release VLAN check box.

• Designate the VLAN for the clones linked on a network interface

  Hi all

  I do a view pilot program using 4.6 and related clones. I have a server (small pilot) to all (vcenter, connect to the server, clients). I have configured an interface on the server as a TRUNK so I can have desktop VMs on different VLANS. How to configure view (or the desktop image base) to clients pools on the VLANs that I would like on?

  For example, computer office-pool1 I want to VLAN 10, office-pool2 I VLAN 11.

  Base Office I created, I put the VLAN 10, but the VMs system (created from the replica) begin on VLAN 11.

  Thank you

  Mike

  You must create groups of ports for each VLAN.  Then go to your parent image, change the nic for the port group you just created and to recompose.

• Separate the pegs for the beginning and the end of a line

  Is there a way of 2 anchor line anchor?

  For example, in the screenshot below, I would like to the first anchor where it is after the E to the beginning of the line and a second anchor by the image of the cat for the arrowhead

  

  You mean that if you move the cat autour, the line would follow automatically?

  N ° not even Illustrator (the candidate of choice for such a function) can do.

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• Separate the VMkernel for pulse data store traffic?

  Hello.

  I was just reading Tech EqualLogic report 'Configuring iSCSI connectivity with VMware vSphere 5 and Dell EqualLogic PS Series storage' and saw something again on pages 3-4.

  Dell recommends to create a vmkernel port highly available on the subnet iSCSI serving as vmkernel default port for pulse data store traffic, so that the pulsation of data store traffic will then sit outside the iSCSI Software initiator and consumes any connection of additional iSCSI storage. He goes on to say that the traffic of pulsation of the data store will always use the lowest numbered VMkernel ports on the vSwitch.

  It makes sense, but this is the first I've heard of this. Everybody does that, with EQ or other iSCSI solutions?

  Thank you

  Brian

  
  

  Not sure that what talking about Dell, but the heartbeat "traffic" data store using the links normal iSCSI. Each host will have a file on one of the heartbeat data stores and open it which means there a lock on the file. The overhead is minimal and there is no need to worry at all.

• How to assign the password for different SSID in embedded AP - w1941 Cisco

  Hello

  Can someone tell me the configuration of the CLI of assinging for SSID password created in cisco integrated access point 1941.

  If so, then can we use WEP encryption on cisco 1941 AP?

  Yet one thing, I get the message click the SSID that "information sent over this network might be visible to others" what does this mean and how to solve this problem. Thank you

  Gotcha!

  The command is...

  encryption [vlan vlan-id] key 1-4 size { 40 | 128 } encryption-key [transmit-key]
  
  We need to map the Vlan for each SSID..
  So the comand will be..
  encryption (vlan vlan#) key 1 size 40bit 7 F3546E765203 transmit-key
  We need to make sure that... under the SSID, we have mapped the coresponding vlan..
  that is.. if you have a SSID by name XYZ and you want the clients to get the IP from vlan 10.. then the config will be..
  en
  
      config t
  
      dot11 ssid XYZ
  
      vlan 10
  
      auth open
  
      mbssid guest-mode
  
      end
  config t
  
      int dot11 0
  
      encryption vlan 10 mode wep mandatory
  
      encryption 10 key 1 size 40bit 7 F3546E765203 transmit-key
  
      no shut
  
      end
  and followed by the subinterface commands.. and the same should be done for all the other SSIDs with different VLAN mappings and keys.
  let me know how this works out for you!!
  Regards
  
      Surendra
  
      

• Configuration of VLAN for vMotion (ESXi 5.1 update 3)

  Hello

  We use a cluster of ESXi 5.1 updated 3 guests with Enterprise Edition.

  Finally, our network is being upgraded and VLAN will be created for vMotion.  Currently, we use the local network for the management and vMotion (I know that's not good).

  Network administrator asks me to provide information concerning the requirement of the VLAN for vMotion.

  Is there any Document KB I can refer to mentioning that the administrator must put in place in the physical switch and I need to change in each vSwitch for vMotion on all ESXi hosts?

  Thank you

  Belong to your network administrator if it can link your vmotion IP to the same vlan that he will provide den it's possible.

  Otherwise, you will have to go to the configuration of your network administrator. so it can provide you the IP for the ports of vmotion.

• With the help of Vlan for LAN and DMZ

  Hello

  For the moment, I have assigned my LAN and DMZ networks to two separate network card (so therefore no Vlan tagging)

  for example vmnic0 = LAN, vmnic1 = DMZ.

  It works well but I like to make changes in the way I want to use two separate physical network adapter and use on the two s two LAN and DMZ nic but now using the VLAN.

  So think of this configuration:

  For each network, I create a Vswitch, in order to obtain a Vswitch named VsLAN, VsDMZ for the case.

  The Vswitch I attribute a two nic Nic will be the day before. as vmnic0, vmnic2 (at rest)

  This Vswitch I create a port group and assign the correct number of VLan as LAN 10 and 20 to the DMZ.

  Create the another Vswitch will have the same Nic but now vmnic0 will be the stanby one.

  Probalby all great so far I think or not?

  Issues related to the:

  -Well this concept where there is a relationship a Vswitch and port group or a switch with multiple exchanges?

  In case a Vswitch with multiple port groups I will assign to group level reserve and the active NIC Port.

  -If I create a group of ports and assiging several Vlan IP packets received by the virtual machine itself also be labelled or not identified?

  Other words. Do I need to configure the NETWORK adapter to the virtual machine also for the same local network ID virtual or not.

  Thanks for your comments.

  Hello

  Change of vlan is a pretty good idea to get the failover and the performance of the network LAN and DMZ. You have confused somewhat however concepts.

  A can only be used in a vSwitch vmnic. So what you want to do is the following:

  Create a vSwitch

  On the vSwitch create two ports: LAN (vlan10), DMZ (vlan20)

  If vmnic0 and vmnic1 have access to the vlan10 and 20, then simply add the two vmnic virtual switch. By default, they will both be active and that's fine. If you do not want to CHANGE the GRPE ports LAN and goto the "failover" tab and put vmnic0 as active and vmnic1 as before. Then do the reverse on the DMZ port group.

  Best regards

  Frank Brix Pedersen

  blog: http://www.vfrank.org

• I want to install 2 completely separate Firefox instances, one for the family and the other for me.

  I tried to install each on different hard drives with different names, but no matter what all the bookmarks are connected between the two. I do not open both at the same time and even installed one without him in the start menu programs. nothing prevents them to act as a single instance. I don't want to use any kind of profile, just a shortcut on the desktop for an and a folder for each other. How to work around this problem. any help would be greatly appreciated. I have used flock as my default (Firefox), but it is no longer supported or updated, and I can't quite deal with chrome. I know it's Firefox function but so minimal and causes that I don't like it.

  Portable Firefox installed on the hard drive will provide a completely separate browser, so you don't have to do anything with the 'profiles' - which is run automatically by the program.
  
  http://PortableApps.com/apps/Internet/firefox_portable

  Google Chrome has no link with Firefox, Mozilla or Gecko based, it uses WebKit as its core and is more related than any other browser to Safari,

• 6520 everything in a single analysis won't let me check the box for the preview or scan as a separate file

  I would like to analyze more than 1 photo at a time, but the preview or scan separate file box is there but will not let me check this function so it will separate the photos when they scan... Thanks for any help.

  The feature you're talking about is not what you think it does. This feature just ensures that every scanned image is separated from the others. The ability to place multiple images on glass and have them scanned in the form of different images, which is what I think that you are looking for, was removed in the software. I'm sorry.

• Error F0933: The VLAN named for vNIC can be solved.

  I have searched in net help on this one, but I can't seem to find anything.  We have recently improved our UCS chassis, the IFS and the blades of 2.0(1q) to 2.1 (1st) and we receive an error on all our VLAN configured.  The VLAN is functioning and passing traffic, but I would try the 900 + compensation warnings.  Here are the details of the error:

  <>

  ACK = "no".

  cause = "referenced-vlan-insoluble".

  Code = "F0933".

  created = "" 2013-05 - 06 T 18: 05:12 ""

  descr = vlan "named VLAN_406 QA for VM1 vNIC can be solved."

  DN="org-root/ls-QA_ESXi-1/ether-VM1/if-QA-VLAN_406/fault-F0933".

  rule = "vnic-ether-if-vlan-insoluble".

  gravity = 'warning '.

  status = 'created '.

  Tags =""

  Type = "configuration" >

  Any help is greatly appreciated and I thank you in advance.

  You deleted a VLAN system under the tab 'LAN', but there's a vNIC model or a model of the referencing service profile.   We have just now in 2.1 added a "check" to make sure of any VLAN referenced in a model vNIC resolve to one VLAN assets.

  Search for and delete the model/policy and it will disappear.

  Kind regards

  Robert

• The vlan vmotion should join him vlan management for vmotion work?

  Host 1

  Management network is a vswitch. IP VLAN 350 172.31.250.201

  vMotion network is on an another vswitch. VLAN 500 IP 192.168.1.1

  Host 2

  Management network is a vswitch. IP VLAN 350 172.31.250.202

  vMotion network is on an another vswitch. VLAN 500 IP 192.168.1.2

  Running Cisco UCS, the vNIC for vmotion are the vlan 500 but vmotion works only when they have access to the vlan 350 the management vlan.

  Sorry for the question noob but not vmotion need access to the vlan management in order to work?

  Thank you

  No, what you're doing - vMotion running in a dedicated subnet - is actually recommended to do this. Ensure that the UCS switch ports are configured correctly, allowing the VLANS required.

  André