How to configure the VLAN for Cisco SG500 - switch 28

Similar Questions

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• How to configure the VLAN-access plan on Cisco 3650

  Hello

  I would like to configure the VLan-access plan to filter some of the traffic VLAN, but I am unable to run vlan-map command on the cisco L3 3650 v03.06.00E

  Hello ahmed,.

  According to the command search tool, 3650 v03.06.00E does not support the vlan-access plan.

  You will need to catalyst 3650, 3SE to configure "vlan access map.

  https://Tools.Cisco.com/support/CLILookup/cltSearchAction.do

  Show vlan-plan of access (catalyst 3650, 3SE)

  VLAN-access plan (catalyst 3650, 3SE)

  I hope this helps.

  Please evaluate the useful messages.

  Thank you.

• How to create the VLANS on Cisco PIX 6.3?

  Hello

  How to create a vlan on pix - 6.3? I'm a little confused.

  How can I assign one side of the internet with several (not secondary IP address) ip address for each & every vlan?

  How I connected to the switch, I mean if I put "switch trunk mode port" on the side of the switch, what command should I I need on the PIX 'inside' interface? in the router, the command is "encapsulation dot1Q 1.

  also there are restrictions which limited only VLANS can be created or is it unlimited?

  Hello

  When you configure your interface, usually do you it like this

  interface ethernet0 car

  Auto interface ethernet1

  Ethernet1 is a trunk with a vlan 2 and one vlan native, you must add to your config:

  logical interface ethernet1 vlan100

  logical interface ethernet1 vlan200

  After that, you must name these interfaces and define the level of security.

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif V200 interieure4 vlan200

  nameif vlan100 V100 securite6

  This configuration will give you an interface (eth1) with 1 vlan (inside) 2 and native vlan tagged (v200 and v100)

  PIX won't negotiate a trunk, your switch configuration is correct.

• How to reset the password for cisco DMM 5.1 equipment machine

  Dear all,

  I have a cisco DMM 5.1 with some players installed on it, I can connect to the multimeter Digital 5.1 via web browser, but I can not connect the hardware directly using the console, I have not the password for access to the console, could someone please help me reset the password for the server of physica cisco intact DMM 5.1 keeping data and configuration on the server. ?

  
  

  Help, please!

  Dear Fahad,

  If you have lost your 'admin' password, it can be recovered using the account "pwadmin" as shown in the following link:

  http://www.Cisco.com/en/us/docs/video/digital_media_systems/5_x/5_4/DMS/AAI/Administration/Guide/pwadmin.html#wp1079466

  If you have lost your password to "pwadmin" so, you will need to open a TAC case and get an ISO image of "DMS pwadmin 5.1 reset" through TAC. You can then start the machine with the CD provided to reset the password to "pwadmin", and then sign in as 'pwadmin' and reset the password "admin" was from there.

  Kind regards

  Marco

• How to configure the adapter for network WRT54G wireless

  I downloaded the driver for a tenda usb adapter.  What else should I do to connect to the network WRT54G? I am currently connected via an ethernet cable. Running Windows/7.

  TIA,

  Phil

  OK, I found out how locate network and connect. The only problem was that I used the password instead of the key WEP.

• How to configure the proxy for firefox androidversion?

  How to set parameter for android version of firefox?

  Thank you

  Hello

  I have had a look and found this page that should help you.

  If this is not the case please come back here and we'll see what we can do to help.

• How to configure the VPN for Xperia phones

  I know that this does not work for many after the upgrade to KitKat but I just wanted to know how other users were using previously.

  Could you give me the settings or help me how to use these settings.

  VPN does not of course for a lot, but I guess that Sony will do something so he can fix it. But tell me how you used earlier. I am interested in knowing. Never used because I found it difficult. People told me that it is a sort of proxy to surf the net anonymously.

  Sachin4u wrote:

  ... VPN works of course not for many...

  Where did you get this info? I had this problem a few weeks in this forum channel and no useful response has been posted.

  But anyway: on Android 4.3, I added a VPN connection with the 'IPSec Xauth PSK' type and the pre-shared key. At the opening of the connection, I entered username and password. A few secconds later than the VPN connection to my home network with router Fritz Box has been implemented.

  Hopefully, I could help you, Titus

• How to configure the network for Windows XP boot

  I have a laptop from nec.
  the cd player does not work and usb either.
  It has an ethernet jack, but I don't know how to set up at the start of the network
  Please help thanks

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• How to configure the DDC for testing?

  Hi all

  I would like to implement Cisco Secure Desktop in our WebVPN configuration, but I need a way to set up and test without making our existing of WebVPN users.

  It seems to me that if I create a Windows with a criterion that * only * my machine test matches, all other users will fail. If I activate the features "when the location corresponding fails", current users won't see a difference.

  Is this correct? Furthermore, with this configuration, VPN tent making out the CSD software when users connect?

  All advice is appreciated.

  Thank you

  -Steve

  Yes, existing users will not see a difference "when the corresponding location fails. This option "what corresponding location fails" helps Windows customers use VPN to surf the web as a minimum connection option, if the client computer does not match any of the criteria of the configured locations.

• How to configure the site for several vpn site

  Hello

  We are in the process of upgrading the IT infrastructure n/w. Our headquarters is home to all servers. I want to establish a vpn between our head office and our 4 stores connectivity.

  Head offfice LAN - 192.168.1.0/24

  Remote Desktop

  1 LAN 1 - 10.1.1.0/24

  2 LAN 2 - 10.1.2.0/24

  3 LAN 3 - 10.1.3.0/24

  4 LAN 4-10.1.5.0/24

  I want to implement the ipsec through our internet vpn. An example of a config would be useful. Thank you

  Not very easy to find an example of a config...

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a0080094525.shtml

  But you have to ORC.

  Federico.

• How to configure the application for child object View?

  I have a hGrid standard layout. Two display objects are present, sign in using the link display. I need to define where clause in the child View object. The changes themselves do not appear when I put the where the clause. Also when I try to extract rowCount returns 0 for child View object. But I'm able to get the parent View object value. Any suggestions please.

  Hi Shrikant,

  Thanks for your replies. I was able to find a solution. Was able to achieve thanks to the functionality of the rowset.

  Kind regards
  Pradeep

• How to configure the settings for both tables?

  SELECT GM. GRNNO, GM. GRNDATE, SUM (GS. APPROVED), SM. ISSUENO, SM. ISSUEDATE, GS. ITEMCODE, SUM (SS. ISSUEDQTY)
  OF GS, SM IMS_ISSUEM, GM IMS_GRNM, SS IMS_ISSUES IMS_GRNS
  WHERE GM. GRNMSERIAL = GS. GRNSSERIAL
  AND SM. ISSUEMSERIAL = SS. ISSUESSERIAL
  AND GM. POSTED = 'T'
  AND SM. POSTED = 'T'
  AND GS. ITEMCODE = SS. ITEMCODE
  AND GS. ITEMCODE ='01-01-02-019'
  AND *.
  GM GROUP. GRNNO, SM. ISSUENO, GM. GRNDATE, SM. ISSUEDATE,
  GS. ITEMCODE STOPPED BY GM. GRNDATE, SM. ISSUEDATE;
  
  Here, I have to select the data in the tables between two named parameters: P_1 and: P_2.
  the column date of IMS_GRNM is named GRNDATE.
  the column date of IMS_ISSUEM is named ISSUEDATE.
  How to set these parameters?

  I think what you need is
  Where table1. Column1 between: p1 and: p2
  and table2. Between Column2: p1 and: p2

• How to assign the password for different SSID in embedded AP - w1941 Cisco

  Hello

  Can someone tell me the configuration of the CLI of assinging for SSID password created in cisco integrated access point 1941.

  If so, then can we use WEP encryption on cisco 1941 AP?

  Yet one thing, I get the message click the SSID that "information sent over this network might be visible to others" what does this mean and how to solve this problem. Thank you

  Gotcha!

  The command is...

  encryption [vlan vlan-id] key 1-4 size { 40 | 128 } encryption-key [transmit-key]
  
  We need to map the Vlan for each SSID..
  So the comand will be..
  encryption (vlan vlan#) key 1 size 40bit 7 F3546E765203 transmit-key
  We need to make sure that... under the SSID, we have mapped the coresponding vlan..
  that is.. if you have a SSID by name XYZ and you want the clients to get the IP from vlan 10.. then the config will be..
  en
  
      config t
  
      dot11 ssid XYZ
  
      vlan 10
  
      auth open
  
      mbssid guest-mode
  
      end
  config t
  
      int dot11 0
  
      encryption vlan 10 mode wep mandatory
  
      encryption 10 key 1 size 40bit 7 F3546E765203 transmit-key
  
      no shut
  
      end
  and followed by the subinterface commands.. and the same should be done for all the other SSIDs with different VLAN mappings and keys.
  let me know how this works out for you!!
  Regards
  
      Surendra
  
      

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140