Similar Questions

• Split signals you are ordering

  I understand that you can use the module to SPLIT signals to divide multiple signals to a DAQ Assistant of multiple channels. My question is, what is the order of the split signals? If a DAQ Assistant has 4 signals which are then separated by then, the signal coming into the position the highest output is order 0 DAQ signals (and so forth: then above stopped 1... the lowest is of order 3)? If not, what is the command?

  ce_2015 wrote:

  If a DAQ Assistant has 4 signals which are then separated by then, the signal coming into the position the highest output is order 0 DAQ signals (and so forth: then above stopped 1... the lowest is of order 3)?

  Fix.  Regardless of the channel is the first in the list in the DAQ Assistant will be the first signal to divide and down the line.

• ACE you are ordering

  Hello

  I have a very long list that has the following 2 entries, in that order, it contains:

  Show blah ip access list

  1010 deny ip any 192.168.1.128 0.0.0.63 Journal (no matches)
  1200 permit tcp host 192.168.1.130 gt 1023 any eq www (matches actively increments, at the rate of 2 or 3, all a few seconds)

  because the host 192.168.1.130 is contained in the subnet has declined in the previous statement, I am at a loss to explain why the TCP traffic to the specific host is ALSO denied by the previous line.

  Does anyone have a clue as to what could cause this?  What obvious thing I'm missing?  I thought that the hit counter only incremented if traffic has been matched, and it does not really resemble 192.168.1.130 tcp/80 traffic must be allowed.

  (1st 3 octets of the IP address were replaced by the private sector, but the mask and the last byte are the same)

  Thank you!

  What

  Line 1010 is refusing to LEAVE a subnet

  Line 1200 is allow from a host on the subnet to a

  Assuming that it is on a dynamic firewall, the reflexive ACL will allow return traffic that is generated by the traffic being allowed by line 1200.

• The photos shows 'unexpected error' app when you are ordering prints

  WWhen trying to order prints in the Photos app in OS X 10.11 whenever I select express shipping, I see a dialogue "an unexpected error has occurred." I checked that the credit card and address are good for the iCloud account logged in System Preferences. I also checked the same iCloud online account and he has good credit card and address. Any ideas what is causing the error? Thank you. Greg

  SEMs is a bug APple - for a week or so change of quantity or shipping caused an error - no solution I've seen other than keep trying

  LN

• Afer you are ordering of pages of photo album and video. iGet all is great when I opened x

  I use photoshop elements 6 to do a scrapbook digital-i had everyting in order, inclduing video clips and had begun to add music. When iplayed that last time a few days ago, it was perfect. Today, whne I try to open it I get is big x instead of video or photos/scrpabook pages. HHelp!

  I posted the question on the elements of the Photo as you suggestd. Here is the response I got. Can you answer these questions for me?
  She suggests that this is a Moviemaker problem and ask the following on your forum:

  "Movie Maker uses the drive letter Windows to try to locate the jpgs on your USB?
  2A - if so, how do you set Windows to use the same drive letter all the time for a flash drive
  2B - AND can the drive letter that Movie Maker stored your existing jpg files be changed to be consistent with your new permanenetly assigned drive letter? »

  The only change I had on my computer is I bought a "Strip" to add additional positions. I noticed that flash player, sure I have the album is now emerging as 'I' where it used to "H". After that I got the answer above, I moved the flash drive on the original port and it still did the same thing with the red x. I don't have this problem when I open these files with other programs.

  =====================================
  Please explain your project in more detail.

  You create collages in PhotoShop and
  import into Movie Maker?

  Are red Xs in PhotoShop or Movie Maker?

  If the red Xs are in Movie Maker... which indicates
  only the source files have been moved or deleted.
  You may click with the right button on the red Xs and browse
  at the current location of the files sources and re-
  establish the path. John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Help! You are ordering photo book with pictures 1.0.1

  I can't finish my order a photobook with pictures 1.0.1 (urgent!)

  I have compiled, press BUY BOOK, move to the system asking me to you connect using my ID Apple (OK) and it starts to 'ALLOW' then stops and asks me to enter my Apple (OK) registered credit card security code.

  I enter this info, then get a message that says "the credit card associated with this Apple ID is assigned to the Bank of Australia. If you change the store, you will need to place the order again. »

  As I checked the store "Australia" in the preferences of Photos AND have an Australian listed billing/shipping address I hit continue.

  When exactly does nothing... the retractable window disappears and the process seems to have cancelled itself.

  What I am doing wrong?

  Re-enter all your account information, including payment information (do not check but just go)-usually that can solve these questions

  LN

• Petition to a view Linux Agent - sign and drop a line if you are interested!

  In this community, you can find a few discussions where people are asking an agent to view Linux development.

  This officer would make the possibility of a pool of office of linux in Manager mode available.

  I understand this is not as easy as it may seem, there are a lot of distro of linux and the technical difficulties to achieve this goal.

  In addition, if we ever get this agent, expect works as good as the Windows version, have redirect PCOIP and USB...

  To this end, I would like to make a suggestion to VMware to develop a virtual appliance where one or two of the most used linux distro are prepared by VMware. Limited support is acceptable if you tampered with the virtual appliance and broke the addon from view. In my opinion Ubuntu LTS is a serious candidate for such a virtual device.

  I ask everyone who would like to see this suggestion developed to remove a line in this thread AND sign the petition.

  '' I support the request '' would be enough to make the VMware to know how many of you are out there asking for this feature.

  SPREAD THE WORD AND SIGN!

  http://www.change.org/petitions/view-Development-Department-development-of-a-view-Desktop-agent-for-Linux

  

  I think it would be a great blow to VMware, especially with the evolution of cloud computing and the shift towards Web applications that would eliminate the need for a Windows operating system for many users. Of course there would still be some cases where Windows should always be used, but it would be a great solution for the pools created just to allow access to the internet, for example. I'm in. And thank you for having this discussion began.

  Dave

• Message from CDC Web site... In order to offer a web experience more safe, we have updated the CDC.gov site. The browser you are using is not

  When you try to view the CDC Web site, I get the following message.

  «Please update your browser in order for you to provide a safer web experience, we have updated the CDC.gov site.» The browser you are using is not possible because it does not meet necessary safety standards. Please update your browser in order to view the CDC.gov site.

  Thank you for your patience. »

  2 days ago, I could see the site Web of CDC...

  I can view the site without any problems, so I don't think it's to oppose the version of Firefox. This forum is picking up your User Agent string and that seems to be correct - something which causes problems on some sites when it is incorrect.

  Please try the alternative of cache for this site using the shortcut key Ctrl + F5, while, on this site and also erase cookies from this site.

  • _Delete-cookies-for-a-single-site delete cookies to remove the information from Web sites is stored on your computer

  It seems strange that they warn on the display of the site with an outdated browser. They offer a version of the site insecurity themselves. It's not like you're interacting with the site and pay money or connect.

  • Not sure http://www.cdc.gov/
  • Secure https://www.cdc.gov/

• Smartphones, blackBerry, your computer must be connected to the Internet in order to configure synchronization to the start settings. Please ensure that you are able to connect to the Internet, and then try again.

  I get the above message when I try to configure my sync settings... and yet I clearly have an internet connection. I downloaded the most recent desktop software and that did not correct the problem.

  What Miss me?

  Hello 1066stump,

  Welcome to the community of BlackBerry Support Forums

  The following article can help about the problem you are experiencing:

  http://www.BlackBerry.com/BTSC/KB16471

  See you soon,.

• ClickListener in ADF graphic line

  Hello

  Is it possible to have the values of the axes x and y (i.e.coordinates) of the graphic line if the user clicks in an area of the line between the points (not the point itself)?

  I can get the values of the axes x and there if I click on the point on line as follows:

  public void graphClickListener (ClickEvent clickEvent)

  {

  ComponentHandle handle = clickEvent.getComponentHandle ();

  If (handle instanceof DataComponentHandle)

  {

  DataComponentHandle = (DataComponentHandle) handle dhandle;

  Object Val = dhandle.getValue (DataComponentHandle.UNFORMATTED_VALUE);

  Date timeVal = null;

  Attributes [] seriesInfo = dhandle.getSeriesAttributes ();

  If (seriesInfo! = null & & seriesInfo.length > 0)

  {

  Object = seriesInfo seriesName [0] .getValue (Attributes.LABEL_VALUE);

  Attributes [] groupInfo = dhandle.getGroupAttributes ();

  If (groupInfo! = null & & groupInfo.length > 0)

  {

  TimeObj = groupInfo object [0] .getValue (Attributes.LABEL_VALUE);

  If (timeObj! = null)

  timeVal = new Date (((Date) timeObj) .getTime ());

  }

  }

  However when I click on one area of the line between the points (not the point itself) I can get only the information series, not axis x and axis are name value:

  ElseIf (manage instanceof SeriesComponentHandle)

  {

  Get the attributes for the series

  Attributes [] seriesInfo = ((SeriesComponentHandle) handle) .getSeriesAttributes ();

  String data = "";

  If (seriesInfo! = null)

  {

  for (uploading Attributes: seriesInfo)

  {

  data += "\nSeries value:"+ attrs.getValue (Attributes.LABEL_VALUE);.

  data += "\nSeries name:"+ attrs.getValue (Attributes.LABEL_ATTRIBUTE);.

  data += "\nSeries id value:"+ attrs.getValue (Attributes.ID_VALUE);.

  data += "\nSeries name id:"+ attrs.getValue (Attributes.ID_ATTRIBUTE);.

  }

  }

  System.out.println (Data);

  }

  }

  Here is the source of the jsf file:

  < dvt:graph id = "lineGraph1" animationOnDisplay = "auto".

  tabularData = "#{pageFlowScope.gaphPageStateBean_backing.graphTabularData} '"

  customToolTipCallback = "#{pageFlowScopegraphPageStateBean_backing.callback} '"

  graphType = "LINE_VERT_ABS."

  seriesObjectCount = "#{pageFlowScope.graphPageStateBean_backing.seriesCount} '"

  timeRangeStart = "#{pageFlowScope.graphPageStateBean_backing.graphStartDate} '"

  timeRangeEnd = "#{pageFlowScope.graphPageStateBean_backing.graphEndDate} '"

  timeAxisInterval = "CTAI_MINUTE" timeRangeMode = "TRM_EXPLICIT".

  "partialTriggers =": commandLink1: t1:cb7.

  Binding = "#{backingBeanScope.graphPageBean_backing.graphBinding} '"

  clickListener = "#{backingBeanScope.graphPageBean_backing.graphClickListener} '"

  timeAxisType = "TAT_IRREGULAR" textAntialiasing = "true".

  scrollListener = "#{backingBeanScope.graphPageBean_backing.scrollListener} '"

  zoomListener = "#{backingBeanScope.graphPageBean_backing.zoomListener} '"

  markerTooltipType = "MTT_VALUES_TEXT" >

  < dvt:background / >

  < dvt:graphPlotArea / >

  < dvt:seriesSet defaultLineWidth = "3" defaultMarkerColor = "#ffffff".

  seriesMap = "#{pageFlowScope.graphPageStateBean_backing.lineGraphSeriesMap} '"

  markerDisplayed = 'true '.

  defaultMarkerShape = "MS_CIRCLE" / >

  < dvt:o1Axis id = "rhrhtr6" scrolling = "on" / >

  < dvt:y1Axis id = "fwef43" lineWidth = '1' axisMaxValue = '1.0 '.

  axisMinValue = "0.0" logarithmicBase = "10" / >

  < dvt:legendArea automaticPlacement = "AP_NEVER" rendered = "false" / >

  < dvt:o1TickLabel id = "o1TickLabel1" tickLabelSkipCount = "50".

  tickLabelSkipMode = "TLS_MANUAL".

  tickLabelSkipFirst = "0" / >

  < dvt:y1MajorTick id = "y1MajorTick1".

  tickStyle = "#{pageFlowScope.gaphPageStateBean_backing." YAxisTickLine} "/ >"

  < rendered dvt:y1TickLabel = "false" / >

  < dvt:shapeAttributesSet id = "shapeAttribSet1" >

  < component dvt:shapeAttributes = clickable 'GRAPH_AREAMARKER' = 'true '.

  ID = "shapeAttrib1" / >

  < / dvt:shapeAttributesSet >

  < dvt:timeAxisDateFormat timeFormat = "HOUR24_MINUTE."

  yearFormat = "YEAR_LONG."

  monthFormat = "MONTH_SHORT."

  quarterFormat = "NONE" / >

  < dvt:o1Title text = "" time: "horizontalAlignment ="LEFT">"

  < dvt:graphFont id = "graphFont1" emphasized = "true" color = "#002173" / >

  < / dvt:o1Title >

  < dvt:annotationSet annotationMap="#{pageFlowScope.graphPageStateBean_backing.graphAnnotationMap}"/ >

  < / dvt:graph >

  Thank you.

  Valon

  JDeveloper 11.1.1.5.0

  AF:graph

  Except if a function is used to interpolate the data points, is not possible.

• Maximum graphical line of items

  Hello
  
  I have a report page that also contains a chart area. Once I submit to the dates entered will appear between the dates, and also line chart will appear. In the chart, I have the "tax" on axis y and the days on the x axis. Once my period of 15 days, there is no problem with the graph. However, if I want to look at the graph each month, it goes to 15 days. So, my question is that if graphic line supports up to 15 entries or not?
  
  Thank you

  Hello-

  Looks like your graphical query of the series is limited to 15 lines. You can change this value in the App generator.

  Austin

• Satellite M40: Errors graphics when you change the screen resolution

  Hello
  I have a Satellite M40 and a big problem.

  Windows xp pro sp2:
  When a program changes the resolution of the screen, the screen is messed up.
  I see only scratches and only a reboot can run back (or suspend-to-disk).

  [edit]
  I plugged an external monitor to the laptop and it works,
  the laptop screen is full of lines and the 2nd monitor shows what the laptop screen should normally display also
  [/ Edit]

  Linux:
  This can be seen also at the change of the Xwindows mode in linux back to tty(1-6)

  Here are some pictures of this strange behavior:
  http://www.ronnylindner.de/extern/images/Toshiba/Screen1.jpg
  http://www.ronnylindner.de/extern/images/Toshiba/screen2.jpg
  http://www.ronnylindner.de/extern/images/Toshiba/SCREEN3.jpg

  It looks like a hardware problem, but would it be just a bad bios setting?

  What can I do?

  Goodbye and thank you in advance, Ronny

  Post edited by: [email protected]_DE

  Hello

  There may be something wrong with the screen of laptop computers.
  I guess that the graphics card is ok because the external screen works properly.

  But it s very interesting to know if you are using the graphics driver from Toshiba. If this isn't the case, please check if this problem also appears after installation of the graphics driver from the Toshiba driver page.

• Mixed Signal graphic = &gt; line of bad names

  Hello

  I want to use a graph of Mixed Signal and I noticed that the digital waveforms line names are not properly displayed.

  For example:

  The attributes of the wave the nams of line are defined as "Name1" "Name2"; "Name3"...

  On the graph of Mixed Signal, the first line is correctly called 'Name1' but all the others are called "Digital 1-> Line 0"; ' " Digital 2-> line 0 '...

  Is this a bug in LabView?

  If you use a normal digital chart, all names are displayed correctly.

  Yes, I know that I can change the linenames with a property node, but it should also work with the attributes of waveform.

  And a small second question: why are there no digital and mixed-signal graphics cards? I always build them manually...

  Best regards

  Reinhard

  Hello Reinhard,

  I think I found a link that might cover your problem. Looks like it has been known for some time

  How can I assign names to my digital waveform shown mixed graphic Signal?

  http://digital.NI.com/public.nsf/allkb/A6D74595D0EEFA6386257D77006537DE?OpenDocument

  Best regards

  Michael

• Receive message "Please wait while windows configures the status" and then "the component that you are trying to use is on a CD Rom, please insert". I don't have the CD. How can I stop this?

  Windows Setup status

  Whenever I start my computer, I get a series of pop-up boxes that talk about "Please wait while windows configures the State" and then the one that says "the component that you are trying to use is on a CD Rom, please insert".  I have no idea what it is, and I have no disc to put on this line?  If I hit the buttons cancel these boxes enough times to go, but it's annoying and there is notihing badly with the operation of the computer, after I get rid of the boxes.  No idea how to stop this from happening again?  I did all the steps that have been mentioned earlier and no results.  I even did a system recovery.  I don't know what to delete.  Please help thanks

  Hello

  These messages usually mean that you have a problem with the HP printing software

  Contact HP

  http://welcome.HP.com/country/us/en/contact_us.html

  Contact HP options at the link above.

  http://h30434.www3.HP.com/

  HP's Support Forums at the link above.

• Find and delete the graphic lines of geometric limits

  Hello world

  I'm really desperate after days of web browsing and the forums that I still cannot understand this.

  I'm working on InDesign CS3 on a MacBook Pro with Snow Leopard.

  I have a catalog of 300 pages, set up thanks to a data merge. Unfortunately this way, I produce 2 graphic lines at the end of each page to which I would like rather to remove. Since I don't want to do it manually to each page and I'll have to set up this catalog quite frequently in the future I would like to remove these lines using Applescript.

  Since I have about 12 more of the same lines on each page (same style, color, stroke etc) I thought that the only way to tell which Applescript to remove is the geometrical limitations because these lines always run the same coordinates on each page.

  Unfortunately I can't understand it. I tried the following code:

  tell application "Adobe InDesign CS3"
       tell document 1
            repeat with oneFrame in (get graphic lines whose stroke weight = 1)
                 if geometric bounds of oneFrame is {0, 0, 0, 210} then
                      delete oneFrame
                 end if
            end repeat
       end tell
  end tell
  
  
  

  RESPONSE

  tell application "Adobe InDesign CS3"
       get every graphic line of document 1 whose stroke weight = 1
            --> {graphic line id 187 of page id 177 of spread id 172 of document "Untitled-16"}
       get geometric bounds of graphic line id 187 of page id 177 of spread id 172 of document "Untitled-16"
            --> {0.0, 0.0, 0.0, 210.0}
       delete graphic line id 187 of page id 177 of spread id 172 of document "Untitled-16"
  end tell
  
  
  

  It worked well for the line to x y 0mm 0mm with a length of 210mm.

  I tried the same thing with a line x 3mm y 134mm length of 210mm with the following code

  tell application "Adobe InDesign CS3"
       tell document 1
            repeat with oneFrame in (get graphic lines whose stroke weight = 1)
                 if geometric bounds of oneFrame is {134, 3, 134, 213} then
                      delete oneFrame
                 end if
            end repeat
       end tell
  end tell
  
  
  
  

  ANSWER:

  tell application "Adobe InDesign CS3"
       get every graphic line of document 1 whose stroke weight = 1
            --> {graphic line id 213 of page id 177 of spread id 172 of document "Untitled-16"}
       get geometric bounds of graphic line id 213 of page id 177 of spread id 172 of document "Untitled-16"
            --> {134.0, 3.0, 134.0, 213.0}
  end tell
  
  

  It was my best shot. No idea if I'm on the right track or totally out of bounds.

  Any help would be much appreciated!

  Thanks in advance...

  Osinho

  Take a look at that show the values for the geometric limits. These figures related to your x and is coordinated and you refer to them by their article in the list, for example, item 1 is the first "134,0" in your list, point 2 is called the "3.0", etc. So you need to refer to "that item 2 of geometric limits = [regardless of the value you're trying to match].

  If your document is very complicated, I think I would add another modifier to ensure that you get the right things, to say if these lines have a color that is not used on other graphic in the document lines, or if their weight of race is different, or even tests two items in the list of geometric limits if there is two that appear systematically in all the elements you want to delete - something for you make sure that you ONLY get references to the items that you want and are not likely to delete something, you need to keep.

  Good luck and welcome to AppleScript!