Server address error

Similar Questions

• express error airport; No DNS server address

  OSX El Capitan

  10.11.6

  MacBook Pro mid-2009

  Coupled with Airport Express Airport Extreme.

  Time Warner Cable improved the internet in our area and it took a new modem. At the new modem and Airport Extreme works with it, having to put the modem in Bridge mode.

  However the station Airport Express a few classrooms is now always flashing orange and the error says "there is no DNS server address.

  If I refresh the DHCP lease it will go green, but less than a minute he keeps flashing orange.

  What should I do?

  The way this is supposed to work, it's that your main router obtains the DNS server address of an upstream (on the ISP network) server. The wireless access point or router (router in bridged mode) next level gets its the main router DNS addresses. All subsidiary wireless access points get their the next upstream router DNS server address. Your Mac gets these addresses from the router or wireless access point when it gets its IP address.

  It is possible that you may need to turn off all routers, then feed their place in the order of the modem to the outside. But once that happens it is likely to have on them.

  If no joy in doing that, don't use the Admin user on your main router to see what should be these addresses, write them and enter them manually when you need it.

• Web Services problem - server connection error

  Hello world.

  When I try to enable Web Services, I get an error. I am connected to internet (WiFi) and the connection is ok.

  The error is:

  Server connection error

  The printer could not connect to the server. Check the internet connection and try again, or enter a proxy address.

  I do not have a proxy, and the internet connection is ok! Why do I have this problem?

  Thank you very much.

  We will set an IP address of the printer:
  
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the bridge and the first DNS. Let the second white.< the="" dns="" could="" be="" your="" problem.=""  if="" this="" does="" not="" work,="" try="" google's="" dns="">
  -Click 'apply '.
  
  Now, stop the router and printer, start the router, wait, and then start printing.
  
  After that, you will have to redo 'Add printer' using the new IP address.

• Server connection error

  Series of photosmart HP 7520. -J' am trying to scan a document to send and keep getting the message "server connection error" despite the fact that WiFi is showing as connected. I'm not very good with technology! Can anyone help please?

  Hello Alleycat1. I understand that you have a problem scanning to e-mail, about the connection to the server. If you follow the troubleshooting in this HP document, the issue should be resolved, as it contains troubleshooting for this error message: http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?sp4ts.oid=4022328&spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c02524629-11%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  If these steps do not resolve the problem, I would like that you follow these troubleshooting steps (assuming you're the App on the front panel of the printer):

  1 Select the Web Services on the Panel forward, then settings.
  2. Select "delete web services" and wait as the services to be eliminated.
  3. Once finished, you will return to the home page.
  4. Select the Web Services icon on the printer and go through the steps of installing Web Services once more.
  5. you will receive a more recent code. Later, you can use this code to add the printer to your account eprintcenter.com hpconnected.com / using this code.

  6. you can, or that you may create another email address.

  7. try a different scanning to e-mail using the app.

  Please notify me when all troubleshooting is done, and I'll continue to help you if necessary.

  Mario

• HP Photosmart 5520 411 server connection error

  Hello

  Does anyone know how to solve Server connection error 411.?

  I have a Mac, and until recently still for more Mac Wireless scan was fine. Without wire is connected and the computer scan is enabled. The e-mail address and the PIN is correct.

  Thank you very much

  Thank you, turning the router waits for at least 60 seconds and turning them back on and then turn on the printer works!

• Server connection error:-1 there is a problem connecting to the server... hp photosmart 5510

  HP photosmart 5510 e - while a printer B111a

  Windows vista 32-bit

  connection error message-Server error:-1 there was a problem connecting to the server, press Retry or ok to continue

  No changes have been made to my operating system

  Try to add new applications with eprint center of my Compaq Presario CQ60 laptop to my HP printer. Computer tells me that the new applications are there and ready to use, but printer says 'server connection error "? I followed all the instructions to connect to the wireless router, but I'm not sure how to connect to the "Server"?

  The steps below a usually resolve the problem you are experiencing:

  1. unplug the power cord at the back of the printer.

  2. unplug the power cord at the back of your router (and the modem, if they are separated from the router).

  3. wait 20 seconds, then plug the router (and the modem, if necessary) in.

  4. wait for 30 seconds, then plug the printer back and power.

  5. press the button on the front of the printer ePrint, and it should try to connect to Web Services again.

  These steps usually fix the problem, but if it persists, you can try definition of network information static for the printer (which is sometimes useful to stabilize the ability of the printer to get outside of your network to the internet):

  1. tap the wireless at the top of the screen of the printer and note the IP address.
   
  2. Enter the IP address in the address bar of a web browser on a computer and press on enter or click the go button browser.
   
  3. the printer status page must be open.  Click network in the upper part.
   
  4. click on networking on the left.
   
  5. Select the Proxy settings.
  Note: If you are prompted for a redirect, click OK.  If you receive a certificate warning, select the option that allows you to continue anyway.
  If you receive an internal system error, refresh the page until it loads the proxy settings.
   
  6. check that all fields are empty.  If they are not, make them disappear and make sure that the Proxy Server requires authentication is unchecked and click on apply.  You should get a success message.
   
  7. click on the network address (IP) on the left.
  Note: If you only configuring IP address and DNS address with a yellow note Configuration, refresh the page until it loads completely.
   
  8. leave automatic IP IP address Configuration.
   
  9 change the DNS address to the manual DNS Server Configuration.
   
  10. enter manual for the manual preferred DNS Server 8.8.8.8 and 8.8.4.4 for auxiliary DNS.
   
  11. click Apply and you should get a success message.
   
  12. turn off the printer for 30 seconds and then turn it on again to force the new settings take effect.

  Let me know if you have any additional questions. Thank you!

• Server connection error:-1

  I restrained this forum and I tried everything I could find and has been suggested.  I can simply not the web-based applications to connect.

  1. I have restored factory settings

  2. rebooted router

  3. Enter the IP address printers 192.168.1.84 and began to establish the connection.

  4. Add a static DNS 8.8.8.8 and 8.8.4.4

  5. I restarted everthing in the House.

  I always get the same exact error for the server connection error:-1 when I try to access the web based apps.

  These used to work fine and my daughter loved print his page 'of the day. "  It has just stopped one day of work and no matter what I try it will not connect.

  However, the printer works fine on PC Windows 8 and the iPad or the iPhone.

  Please help as we would like to again access coloring Disney pages.

  Well, try to change the network ipv4 only protocol

  you need to get the ip address of the printer first, and then open any web browser, then try typing the ip address of the printer on the url, after that go to the network tab > networking > network protocol > check on ipv4 only > apply

  If it does not work.

  try going into the menu of web services and delete web services and then re-enable back.

  PS: it will remove the ePrint printer address, you can no longer use the same address of electronic mail of the printer, if customize you it.

• B210A Photosmart - server connection error and does not connect to the wireless router

  I have problems setting up and to connect my router to my new printer b210A. Everything goes well with the initial configuration, and when asked to connect to the network at the start, it works. Then he said that the printer requires updates, downloads of updates, reboots, asks me if I want to activate eprint and as soon as I said 'Ok', I get a "the server connection error" and it is then no longer connected to the network. When I get out of the "server connection error" screen and attempt to reconnect to the network, he says 'Success', prints a Test report wireless, but never connects.

  It's the 2nd printer that I have had in a week, given that the person of HP online chatting told me my first printer had problems of "hardware", after experiencing the same problems and I'll be recommended. So - I did, and now I'm running into the same issues. The number of 800 was NO HELP - after recommended I have unplug and reconnect, then telling me there were server errors (when the printer was not connected to the network).

  We will set an IP address of the printer with a special focus on DNS domains:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway

  -For the first DNS 8.8.8.8 and 8.8.4.4 for the second use.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• Cannot change "vCenter Server Address"

  Hello

  After change vCenter server of Windows to 6.0 device

  vSphere replication appliance 6.0 do not work.

  I try change "vCenter Server Address:" to the new IP address, but when I press "Save and restart the service", I get the error:

  "Can't get the SSL certificate: Bad server response; a vCenter server listens on the given host and port? »

  and the new unregistered IP address.

  Hello

  OK, so your problem is the browser's cache. Please close all instances of your browser and then open firefox own all hides browser and open the VAMI RV user interface and go to the Configuration tab.

  PS: Do NOT use IE

  Thank you

  Dzhem

• Please enter IMAP server address

  I'm running on Adobe Acrobat Pro XI (11.0.10) and every time I try to use the file/send file I get the error message: Please enter IMAP server address.

  I tried to fix, uninstall/re-installing Acrobat and also Office (Outlook) but same error message.

  Please notify.

  I was finally able to resolve this problem by updating to delete the following registry key:

  HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Adobe\Adobe Acrobat\11.0\FeatureLockDown\cWebmailProfiles\tDefaultProfile

  The current value is "null", so just delete that no one and leave the field blank.

  Keep in mind that this registry key will be overwritten if you repair or reinstall Acrobat Pro and you will need to update it manually again. Also check your windows GPO maybe this key will be updated / replaced by them.

• Cannot pair VRMS servers - VRM Server generic error. Unexpected status code: 404

  I have been setting up SRM in accordance with the documentation and am at the part where I have a VRM server configured on each side. My next step on the vSphere replication tab is #3 'set up the connection VRMS. When I click on the "Set up the VRMS connection" link I get a dialog box stating: "do you want to configure connection VRMS? I click "Yes" and I get another dialog box stating: "VRM Server generic error. Please see the documentation for troubleshooting information. The detailed exception is: ' unexpected status code: 404'.»

  Anyone seen this before? Do you know how to solve?

  Thank you

  think that it is a known bug that should have been in the "known issues" section of the release notes, but did not for a reason that I'm going to check that out in their own country.

  It seems that during the installation of SRM, vCenter was specified by DNS, while during VRMS vCenter configuration was specified by an IP address. These two must match. IE, if you use DNS (FQDN) in one place use it in other institutions. In my setup, I used addresses IP for both entries during the installation process and does not see any problem.

  If you don't you remember how you have defined vCenter in the SRM installation screen, then I guess the quickest test is to redeploy and configure devices VRMS and doing the opposite of what you did just that is to say if you just use FQDN in the VRMS screens when he talking about vCenter using the IP address instead and vice versa.

• UTL. MAIL error ORA-29279: SMTP permanent error: 501 syntax of address error in

  Hello
  
  I'm new to the forum please excuse if I post not properly without standards.
  
  We need to send mails using the UTL. MAIL package and installed them on the database.
  Whenever I try to send an email, I get the following error:
  
  ERROR on line 1:
  ORA-29279: SMTP permanent error: 501 syntax of address error in
  [email protected]
  ORA-06512: at "SYS." UTL_MAIL", line 654
  ORA-06512: at "SYS." UTL_MAIL", line 671
  ORA-06512: at line 2
  
  The test code that I am running is:
  
  BEGIN
  UTL_MAIL. Send (sender = > 'test < [email protected] >',)
  recipients = > "[email protected]"
  subject = > 'test UTL_MAIL subject. "
  message = > "UTL_MAIL test body");
  END;
  
  I tried different combinations:
  
  BEGIN
  UTL_MAIL. Send (sender = > "test"< [email protected] >"")
  recipients = > "[email protected]"
  subject = > 'test UTL_MAIL subject. "
  message = > "UTL_MAIL test body");
  END;
  
  even tried
  
  BEGIN
  UTL_MAIL. Send (sender = > '[email protected]',)
  recipients = > "[email protected]"
  subject = > 'test UTL_MAIL subject. "
  message = > "UTL_MAIL test body");
  END;
  
  Whenever I get the same error.
  It seems to work with a server exchange e-mail, but never on the SMTP server.
  
  In the SMTP address of the sender server logs is not to have the <>of brackets unlike other emails that are sent to the course.
  It seems that the SMTP server is quite strict and the SMTP administrator will change all the settings on the server.
  
  The version of oracle is as follows
  
  Oracle Database 11 g Release 11.2.0.1.0 - 64 bit Production
  
  Could you please help me with a solution.
  Some how the brackets are undressing (which usually UTL MAIL package), is it possible that I can include the brackets.
  
  Published by: 984757 on January 29, 2013 02:56
  
  Published by: 984757 on January 29, 2013 02:57

  I don't like UTL_MAIL - UI abstraction clumsy and poor and not very well written.

  Had a look at the code. It does this:

  WHILE (ALL_RCPTS IS NOT NULL) LOOP
        UTL_SMTP.RCPT(MAIL_CONN,'<' || GET_ADDRESS(ALL_RCPTS) || '>');
  END LOOP;
  

  The process function GET_ADDRESS() ALL_RCPTS parameter, returns the address 1 of him and updates (in and out) parameter with the remaining string.

  SQL> var address varchar2(200);
  SQL> exec :address := ',[email protected]';
  
  PL/SQL procedure successfully completed.
  
  SQL> exec dbms_output.put_line( 'get_address='||UTL_MAIL.GET_ADDRESS(:address)||' address='||:address );
  [email protected] [email protected]
  
  PL/SQL procedure successfully completed.
  
  SQL> exec dbms_output.put_line( 'get_address='||UTL_MAIL.GET_ADDRESS(:address)||' address='||:address );
  [email protected] address=
  
  PL/SQL procedure successfully completed.
  
  SQL> 
  

  The address is explicitly surrounded by square brackets in accordance with RFC. So what needs to see your SMTP server.

  If this isn't the case-maybe then our UTL_MAIL versions do not match. I don't remember what version I pulled and unpacked UTL_MAIL package code I have.

  Personally, I stopped using the UTL_MAIL earlier. Missing in may points. I wrote my own e-mail package that supports multiple attachments, formatting complex Mime, attachments of 20 + MB in size and so now - running on the UTL_SMTP interface (which provides for mail transport layer). And for the problems you are having, I suggest considering using UTL_SMTP directly.

  Published by: Billy Verreynne on 29 January 2013 12:52
  (Updated with names of entities HTML code for the code snippet to render correctly)

• There was a problem connecting to the server 'SERVER NAME' error guard appearing

  There was a problem connecting to the server 'SERVER NAME' error guard appearing even though the server is not on my current network.  I recently moved my iMac to a different location and a different network, and now he constantly tries to connect to the old server.  This message appears every 30 seconds and several of those who appear (see pictures) it's extremely frustrating because it makes the machine almost useless because I am constantly closing them.  No matter how many times I try to stop the activity monitor it it keeps reappearing, and I even tried a few terminal commands that I found online, then restarted the computer, but still had no success.  I would appreciate all the advice really.

  I hope that gives you an idea of what I got!

• How repair there is an Apple ID server connection error?

  How repair there is an Apple ID server connection error?

  Where to find similar solution anwer?

• Photosmart 5520: Scan to email: server connection error 403 (with app and scan)

  I scanned to send several times than I can count, but a few days ago, I get nothing other than the error "connection server 403 error." I checked the forums and someone said to go into apps and download the application. It did not work. I rebooted and tried everything, which he expects. Yet, nothing. Is this error to do with something outside as the real servers HPs - or is this something internal that I can fix it? I went as far as I can without resetting to factory settings (which I am fearful because I recently had the country code has changed on this issue and do not want to return to the country of origin), someone has any suggestions other than what I've sifted through the forums already?

  Hey @fruitfly20,

  Welcome to the HP forums! I hope you enjoy your stay here.

  I understand that you have some problems with the scan to E-mail on your Photosmart 5520. I can help with that.

  We can try I couldn't see you is to remove and enable web services. To do:

  1. On the printer, click web services icon that looks like a tablet with a phone beside her.
  2. Click settings.
  3. Click on delete Web Services.
  4. Click again on the Web Services.
  5. Click on accept and Yes.
  6. Try scanning to Email.

  I would like to know if it works. If it does please not then let me know and we can try something else. Even if it solves your problems, so please let other users of the forum know clicking on accept as Solution below my post.

  I hope this helps and I hope you have a nice day!