Services Web unresponsive - HP Envy 100 D410

Similar Questions

• My envy 100 D410 running with OS 10.7 produces only one screen black when scanning or copy? Help

  My envy 100 D410 had worked fine for several months.  Recently, the printer works fine but the copier and scanner only produce black and streaked color screens.  I reloaded all drivers and updates, and nothing seems to help.  Any help would be greatly appreciated.

  If the printer performs this when the copy of the front of the printer, the scanner is dead.  I'm sorry.

  Here's how to contact HP technical support: www.hp.com/go/totalcare

• Unable to get web services reactivated on Envy 100 D410

  My envy 100 D410a was once working with ePrint, but has not been used for a while.  I've recently switched to connected HP and had to re - register the printer.  The news to save the printer would not print.

  After trying a few times, I removed the web services and then tried to turn it back on, but every time I get the message "problem connecting to the web services server.

  I have the Group of experts through the troubleshooting to restart the printer, restart the router, nothing helps.  I have currently set an IP address manually and can print wireless via a laptop, but not ePrint and no web service.

  I tried to configure the servers manual DNS 8.8.8.8 and 8.8.4.4 (via the printer IP address URL), but whenever I try, I get an error:

  An error has occurred. (wipv4Page-400)
  Click 'OK' to go back

  The current firmware is: SLM1CN1039HR.

  SOLVED!   This can be closed.  I did a factory reset, but not on the tab network/section.  Once I did this and restarted the printer, web services could be reactivated.  I can now access the printer via HPEPrint.

• Envy 100 D410 printer paper mismatch error

  My Envy 100 gives "Paper mismatch" error when I try to print using ePrint, when I try to print a status report and any other time, I try to print unless in the Windows driver I put quality in the 'project '.

  I tried to clean everything, but no luck, it seemed to just start doing this a few months ago.

  Any ideas?

  From previous posts, I see that this printer is having a problem with the hardware with the paper sensors.  Setting the printer in project mode overrides the paper sensors and works around this problem.  However, it seems that web services are unable to pass even with the project defined mode.  So, I guess that this printer is out of warranty is an Envy 100.  I would say that at this stage, the best idea with this printer is to print in draft mode of the computer and try copies in fast mode.

  If you want to use web services, then this product of replacement would be needed to take advantage of this feature.  Good luck.

• HP ENVY 100 D410 CN517A Duplex printing problem

  My printer jams every time I try to print on both sides of the paper (as is pull the inner paper after printing the first side). It's the same kind of paper, I am using since I bought it, and it used to work before (so no, this isn't a problem with the paper). The only thing that has changed recently is that I changed the ink cartridges, but I was able to do some work before duplex he screwed up. I am on Windows 7 by the way. Any suggestion as to what is wrong?

  KeyllyNYC said it is an instrument in the service of the printer for "cleaning of the paper source.

  Go to the configuration Menu (it looks like a key), click on 'Tools' and the fourth option should be "own paper source."

  If that doesn't fix things, you can manually clean the rollers inside the machine. Simply open the lid of the scanner, then access of transport cover. In the back, there is a removable access door roller, pull it out. Then with a damp cloth wipe Lint (like a coffee filter or a microfibre cloth) large rubber rolls and let them dry.

  

  When they are dry and closes the printer, try printing again.

  I hope this helps!

• ENVY 100 series D410: Envy 100 D410 series will not scan with Mac OS Sierra 10.12

  Hello, I just bought a new Mac, and I have the Mac OS Sierra 10.12

  The printer works fine but I can't scan.

  I do not have the scanner HP 3 that previously had on my other computer and I don't have the installation CD.

  I can't find the software online. He said that HP still has the software to make it work, but I can't.

  I tried the HP Easy Scan but I need the previous software that I don't.

  What can I do?

  Thank you

  Sabrina

  @Sab7

  Welcome to the HP Forums, it's a great place to get help, find answers and advice,
  Thanks for posting your request, I'll be more than happy to help you

  If I understand the scan does not work on the BONE of the Sierra.

  Don't worry, even if the following document does not mention Sierra, the Apple article will guide you through the steps to scan through

  • Image capture
  • Overview
  • Printers and Fax preferences in system preferences
  • Scanner / printer queue

  The basics of the Mac: using a scanner

  I also suggest to use the Apple Scan while you wait for the HP software update. You can use the link below to confirm that your printer is still compatible with your operating system: software of the printer and scanner for macOS Sierra, El Capitan, Yosemite, and the Mavericks.

  For links related, please here.

  To troubleshoot the macOS Sierra problems: click here

  If the information I provided was useful, give us some reinforcements by clicking on the solution and laurels, buttons that help and others see that we have the answers!
  Good luck.

• Never mind. ENVY 100 D410 says Wi - Fi is on, but my iMac says printer not responding do not.

  I'm sorry but I don't know how to remove my question and I somehow accidentally received my printer to work.  Thank you.  I just moved and have a new provider so both have a connection to the provider of wireless, but not to each other.  Any suggestions?  Thank you very much.   have tried to turn the disconnect of the iMac, and the printer, so I have unplugged the century link then reconnected.  Thank you.

  Hi whiskersmom, sorry to hear that you have a problem with wifi connection on your printer. I did some research on the issue and I found a few guides that I think will help you in case of problems. Please click on the link I provided.       http://h10025.www1.HP.com/ewfrf/wc/documentSubCategory?tmp_rule=86228&tmp_task=solveCategory&cc=us&DLC=en&lang=en&LC=en&product=4073738

  If this does NOT resolve the problem, please let me know and I'll be happy to offer more assistance.

  Thank you

• ENVY 100 D410

  Screen says "Do not, power down during the update" permanently. The screen will not display anything other than this message. Printer works when connected by cable but not wireless.

  Read this.

• ENVY 100 printer D410 - screen says "Do not, power down during the update" permanently.

  I'm a Mac user Mavericks 10.9.1 running on a Mac Book Pro.

  I have a HP ENVY 100 D410 printer that works your for a few years.

  Recently, the LCD screen of the display on the printer offered, "there is a new driver. You want to update? "(Yes/no)

  (Or something close to that.)

  Unfortunately, I chose 'yes '.

  The printer then tried to update, but eventaully the LCD screen on the printer displays a flashing message:

  "Do not feed, down during the update"

  The printer now flashes just this screen continuously. The LCD screen will not display anything other than this message.

  The printer works when connected by cable and wireless. (Airprint works very well).

  I can scan documents, I can print pages, I can even access printers "Web page.

  But the LCD touch screen control panel is 'stuck' in flashing update message.

  I can't find any way to clear this error and allow the printer to complete the update.

  Help. Please, I beg you.

  Hello

  There is a fix to resolve the specific problem, but I'm afraid it is only available for earlier operating systems under OS X 10.5 and 10.6, Windows XP, Vista or 7.

  I you suggest to get a computer with any operating system supported, install the latest version of the software on the HP site using a USB and then follow the steps.

  The latest version of the software can be found below (the basic software should be sufficient):

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&OS=4062&product=4073738&softwareitem=MP-92513-1&sw_lang=&

  Make sure that you carefully go through the procedure to the installation section in the patch download page.

  Hope that helps,

  Shlomi

• ENVY 100 all-in-one: Envy 100 printer all-in-one - will not glossy paper 250 gsm

  Difficulties that the printer will not accept 250 gsm paper past the printhead.

  Followed him orders for cleaning rollers, reset by disconnecting the power and brought etc. cartridges.

  I note others have had the same problem which seems to have been set by a semi of hardware reset. How can I get the required for the semi reset procedure?

  Thanks in advance.

  Welcome to the @noxasforums.

  I saw your post about your Envy 100 not pulling by glossy paper 250 gsm and wanted to answer you! I checked the specs for the Envy 100 and as you can see below, the printer should take in if you use a format supported below. Maybe you can try the steps from the link I posted for you. I think the cleaning rollers should help. You can also try to select different types of paper to see if one works better than the other.

  Let me know what happens!

  • HP ENVY 100 (D410) and 110 (D411) e-all-in-One Printer Series - 'in paper' Error Message displayed the ENVY and the printer isn't looking upwards or the paper feed

  Tip: Make sure that the printer is plugged directly into a wall jack, avoiding bars power and surge protectors. This ensures that the printer is full on.

  

  Testify of my answer by pressing the thumb in the air below and hit the "accept as Solution" button, if I have you helped a resolution!

  Good luck!

• ENVY 100 - jam paper with glossy (250gms)

  Hi I have a HP Envy 100 (D410) printer all-in-one and that you were never able to print on glossy photo paper or any document on 200gsm.  Even though the manual says you can go up to 271gsm.

  The document tries to feed and then I get a paper jam error message.  I tried the HP and Epsom glossy A4 inkjet photo paper (220 and 250 g/m²) and 250 g/m², 4 x 6 photo paper glossy.  Until they reach the print head and cause a jam.

  any help would be appreciated.

  Thank you np1664

  You can try cleaning the rollers as described in the following link.  Click here.   Sometimes, a thorough cleaning of the rollers can help in this type of situation.

  If this does not help, we could do a complete reset of semi.  Let me know if you want to try it and I can send you the steps in a private post.  I need you agree to not post the stages.  I agree that the problem is probably material, but a reset complete semi can help when there is a problem of coordination between the different parts of the printer.

• "Problem connecting to the Server Web Services." - HP Envy 100

  Hello world

  I wonder if anyone has the same problem as me. I just got a HP Envy 100 and went through the process of setting up without problem. The printer is connected via Wi - Fi for wireless network, I can ping the printer from my Mac successfully and I can print within the network without problem.

  However, regarding ePrint and Web features, it seems that nothing really works. I can't even turn on Web services, I always get the message "problem connecting to the Web Services server.

  I tried the following:

  -Restart the router and printer

  -Change the manual IP address and manually set the DNS server

  -Reapply automatic IP and set the Google DNS (8.8.8.8 and 8.8.4.4) servers

  .. .with no chance whatsoever. If this is a problem with the firmware (from what I understood, I do not have the latest firmware, but I can't ask her update, because it requires, you guessed it, a connection on the server of web services, that is the whole of the problem.)

  Anyone else having the problem? Everyone had it and fixed it? Is this just a temporary problem with HP servers?

  Thanks in advance!

  Hey, for me it works as well, and I didn't, just retried that I had tried before and it connected to the Web Services without problem.

  So I think it's safe to say that the original problem in this topic only lied to a HP Server-side problem. Not cool it took so long for them to solve and in particular the fact that we did not really have feedback appropriate about the problem.

  Anyway, I solved (for now, at least).

• No internet after using the Envy 100

  Whenever I use the Envy 100 (or to be more precise: when the urge got a Wi - Fi connection) I lose internetconnectivity. But only after I finish a session to my router (Linksys WRT610N). When I turn off the router and the next time, it cannot connect to my internetmodem (Linksys AM200) at all. WiFi is in place, but I have only local access, apparently the router cannot connect to my modem (which indicates both the CABLE with the router as the to Internet is up.)

  This only happens after the sessions where I used the desire, otherwise everything is OK. During these sessions, there is no problem, only after the start a new. The only way to restore the connection is reset my hard router and reconfigure.

  BTW. I am one of the users who are unable to get a connection to the webapps desire, but there work ePrint - that is another thread on this forum. Not sure if the two problems are or are not connected.

  Any help or pointers?

  herstil wrote:

  Whenever I use the Envy 100 (or to be more precise: when the urge got a Wi - Fi connection) I lose internetconnectivity. But only after I finish a session to my router (Linksys WRT610N). When I turn off the router and the next time, it cannot connect to my internetmodem (Linksys AM200) at all. WiFi is in place, but I have only local access, apparently the router cannot connect to my modem (which indicates both the CABLE with the router as the to Internet is up.)

  This only happens after the sessions where I used the desire, otherwise everything is OK. During these sessions, there is no problem, only after the start a new. The only way to restore the connection is reset my hard router and reconfigure.

  BTW. I am one of the users who are unable to get a connection to the webapps desire, but there work ePrint - that is another thread on this forum. Not sure if the two problems are or are not connected.

  Any help or pointers?

  A FW update was recently released to solve the problem with access apps... If you have not received notification on the urge of an available update, you should be able to go to your desire screen and select settings (wrench) > Web > Product Updates > check product updates get the latest FW installed on your printer.

  Regarding the other question - routers are not intended to be turned on/turned off constantly, but it must always connect to your reliable modem after reboot.  Complete the FW update and see if the problem persists.  Also, can you share why you turn off the router on a regular basis - there is really no need to do so.

• HP envy 100 don't scan

  I have not been able to scan from the printer control panel in a long time, but I've always been able to browse webscan.  All of a sudden which is no longer available.  The saved Web page reflects my printr IP but the links on the homepage, scan, settings, etc. do not connect to something more.  I ran the Print and Scan doctor and that was a failure.  If I select the printer from devices and printers there are no scan options at all.  I am on Windows 7 and do not know when this ability is gone I do not often scans.  Any ideas?

  Hello

  You try to scan via Webscan or perhaps via the HP software?

  When you select your printer in devices and printers, you can see the following options?

  -HP Printer Wizard

  -See what's printing

  -Setting preferences

  -Customize your printer.

  If so, uninstall the current software from following programs > HP > HP Envy 100 > Uninstall.

  Then download and install the latest version of the software below, which should fix the problem and restore any functionality back.

  The latest version of the software can be downloaded below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-109403-2&cc=us&DLC=en&LC=en&OS=4062&product=4073738&sw_lang=

  Shlomi

• Hello. How can I set a position of default return for the façade of an Envy 100 AIO?

  Hello.. I was wondering if it is possible to adjust the position of the back to the front panel on my Envy 100 AIO once a page has printed and withdrew the output tray.  THX

  Hello

  There is no adjustment to make, but there is a firmware update that should fix this. The firmware update will make the display to go back in the correct position. You can download from the unit by going into the Setup menu, find the Web menu and go from there, choose "Search for updates".