Setting of your Hp printer when he lights not or answer.

Similar Questions

• HP Officejet Pro 8600 N911a: HP Officejet Pro 8600 N911a - Print when Fax is not saved

  Can I do so a fax is printed when it is not registered?

  I know that I can put to print and save every time, but I trust HP digital fax to save paper.

  If a fax is not registered, either because of a network error, or if the computer that logs usually in is cut off, can just fax be printed?

  @MrMeow, it's nice to meet you.

  I think I found something that can help your fax dilemma.

  This information has been in the User Guide for the Officejet Pro 8600 e-all-in-one - N911a; PG 69.

  Set up backup fax

  According to your needs best and security, you can configure the printer to store all faxes it receives, only faxes it receives while the printer is in an error condition, or none of the faxes it receives.

  The following fax backup modes are available:

  On >  The default setting. When backup fax is enabled, the printer stores all faxes received in memory. This allows you to reprint up to eight more recently printed faxes if they are always saved in the memory.

  NOTE: When the memory of the printer is low, it replaces faxes print, older because it receives new faxes. If the memory is full of unprinted faxes, printer stop to answer incoming fax calls.

  NOTE: If you receive a fax that is too large, as a very detailed color photo, it cannot be stored in memory due to limitations of memory.

  Error only > Causes the printer to store faxes in memory only if there is an error condition that prevents the printer to print the faxes (for example, if the printer is out of paper). The printer continues to store incoming faxes, as long as the memory is available. (If the memory is full, the printer stops responding to incoming fax calls). When the error condition is resolved, the faxes stored in memory automatically, print and then they are deleted from the memory.

  Off >  Faxes are never stored in memory. For example, you might want to disable fax backup for security reasons. If an error condition occurs which prevents the printer to print (for example, tracks paper printer), the printer stops responding to incoming fax calls.

  NOTE: If the backup fax is turned on and you turn the printer off, all faxes stored in memory are deleted, including any unprinted faxes that you might receive while the printer was in an error condition. You must contact the senders asking them to return the unprinted faxes. To get a list of faxes that you have received, print the Fax log. The Fax journal is not removed when the printer is off.

  To set backup fax from the printer control panel

  1 tap (right arrow) and select Setup.

  2. press Fax Setup, and then click Advanced fax setup.

  3. press on the backup Fax reception.

  4. press on , error, or out of service.

  Reprint of faxes received from memory

  If you set backup fax mode to On, received faxes are stored in memory, whether the printer has an error condition or not.

  NOTE: After that the memory is full, the oldest faxes, prints are replaced as new faxes are received. If all stored faxes are not printed, the printer does not receive fax calls until you print or erase memory faxes. You can also delete the faxes in memory for purposes of confidentiality or security.

  According to the sizes of the faxes in memory, you can reprint up to eight more recently printed faxes, if they are still in memory. For example, you will need to re - print your faxes if you have lost the copy of your last draw.

  To reprint the faxes in memory from the printer control panel

  1. make sure you have loaded paper in the main tray.

  2 tap (right arrow) and select Setup.

  3. touch Tools , or Faxand then select reprint faxes in memory. The faxes are printed in reverse order, where they were received with the most recently received fax printed first, and so on.

  4. If you want to stop reprinting the faxes in memory, press the Cancel button.

  Please let me know if these steps solved your problem, or if there is anything else I can do to help.

  I look forward to hear from you!

  Thank you

• Can I use your Apple TV when I do not have a modem, and I use the Wifi in the hotel room?

  Can I use your Apple TV when I do not have a modem, and I use the Wifi in the hotel room?

  Thank you!

  Probably not, but depends on the hotels wifi access. most of the hotels that I stay in you will have to "login" via web browser and the ATV doesn't have access to any browser...

  your best bet would be to broadcast directly from a mobile device connected to the tv in your hotel via a HDMI adapter...

• Why is printing when it is not available in 32-bit color mode

  PSCC in use. Why is grayed out impression, therefore, not available in 32-bit mode? If I convert an image to print in 16-bit mode is available, even if the image is all messed up.

  Floating point / linear color modes more or less need to work with initially, given that any color profiles range is so broad, there is no predictable way to obtain a conversion of colors for printing. This is a limitation that you have to live with.

  Mylenium

• Impossible to install the new printer, Pixma MG5320 without error "setting up the network printer down.

  I have a new all-in-one Canon Pixma MG5320. I am unable to get the installer to finish with on "setting up the network printer down." Despite numerous attempts to:

  (1) download the driver on the internet instead of the installation CD.

  2) with the help of msconfig with selective startup and disabled all programs except Microsoft.

  (3) creates the new administrator account and returned through it all.

  (4) turned off firewall and anti-virus

  The error is compatible and I never have the unit set up under devices and printers. The installation is carried out without any errors marked and you will see the error if you get into the details of setting up and get him. The computer sees the printer when it finds and he answers. The printer and the router, both seem to be communicating correctly. Repair auto and troubleshooting programs I ran as fix - it do not detect errors. The printer works fine through a USB cable. I don't want to continue to use USB because that's why I wanted to go wireless. I'm sure that I forget some of the things I went through in my attempts to get this working. Anyone with any ideas or know what's going on please help.
  Tech of Cannon was very knowledgeable and says he sees this once a month. He believes that some program interferes with the installation process. I do thanks in advance. Nice day.

  Hi Gary,.

  Thanks for posting in the Microsoft Community.

  From the description of the problem, you are not able to install the printer Pixma MG5320. I'll be happy to help you on this question.

  Let us try the steps from the following link:

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is helpful and let us know if you need help with Windows in the future. We will be happy to help.

• Printer installed, but cannot be set as the default printer

  Original title: printer installation

  printer installed, but cannot be set as the default printer

  Hello

  See if that helps you.

  "Set or change your default printer"

  http://Windows.Microsoft.com/en-us/Windows-8/set-change-your-default-printer

  See you soon.

• How is to send the native port of the printer command, when the printer is set as the default printer?

  I installed on a Windows XP printer and set it as default printer.

  I also have the manual provided by the manufacturer of printers, which defines the

  commands that can be sent over the serial port, then the status of the printer

  is extracted.

  Thus, for example, by sending an order consisted of 3 bytes: 34,56,78 to the printer (COM5) COM port

  I can get an answer advising me on the State of the printer.

  However, when you send this command to COM5, I get the following exception:

  "The given port name does not start with COM/com or is not resolved to a valid serial port. Parameter name: portName. »

  for which the printer vendor insisted on request microsoft support center.

  The port name of the printer is properly set to the correct a (COM5).

  Any ideas?

  Hello

  Your Windows 7 is better suited for the IT Pro TechNet public.

  You can follow the link to ask your question: http://social.technet.microsoft.com/Forums/en-US/category/w7itpro

• On Windows 8, by default, OneNote when I try to use the print option. How do I set printer as default and not in OneNote?

  When I try to use the print option. How do I set printer as default and not in OneNote? Also, when I want to print from a web page (on the Web page printing option) it goes to OneNote and not print. I have also pulled up a file saved in OneNote and selected the print option in the Menu. I selected a specific page and is nevertheless not print?

  Because your message is off-topic in the comment forum, I moved it to the forum Windows 8 "Performance and Maintenance", where it is more on the subject.

  As you watch the start page, type "default printer".  A list appears on the right side of the screen.  Tap 'settings' and 'Change the default printer' will appear on the left.  Tap it.  Your devices folder and printers opens on the desktop.  You will see that "Send to OneNote" will have a green check mark next to it.  Right click on the printer, if you have already installed it, then select "Set as default".  Close the folder.  Therefore, when printing, your printer will be the default device.

  If you have not yet installed a printer, make sure you download the latest driver for 8 compatible of Windows to the web site of the manufacturer and install the driver following the instructions of the manufacturer.  Then set the default device.

• "Windows needs your permission to continue" - where is the setting to remove this message when you perform tasks?

  "Windows needs your permission to continue" - where is the setting to remove this message when you perform tasks? Thx a lot...

  Windows needs your permission to continue, where is the setting to remove this message when you perform tasks? Thx a lot...

  Windows needs your permission to continue, where is the setting to remove this message when you perform tasks? Thx a lot...

  You probably means User Account Control. Here's how to disable: http://www.howtogeek.com/howto/windows-vista/disable-user-account-control-uac-the-easy-way-on-windows-vista/

• set up a wireless printer on my laptop

  Can I set up a wireless network from the printer to my laptop running windows XP media center edition service pack 3 which is wireless connected to the internet via my desk top which is connected to the internet?

  1. what version of Windows, including the service pack is on the desk? Windows xp edition family sp 3. HOM

  2. What is the brand and model of your printer? Canon office while a pixma mx310

  3. What is the brand and model of your router (or what box which is connected to the desktop computer)? Westell VersaLink 327W gateway

  4. how and what is connected to the printer? USB cable to the desktop

  Ok.  You can 'share' the Canon printer, which means that you will be able to print to it from your laptop when your laptop is connected wireless to your router.

  This is called 'file and printer sharing' and here are some basic tips on setting up, courtesy of the MVP Malke (you have already completed part A, then start with the part B). Read the part in the first paragraph I put in bold.  If you do not understand the last paragraph on sharing the printer, read one or more of the articles from Google search.

  You can also watch all or part of the first 5 links in this Google search: http://lmgtfy.com/?q=xp+sharing+printer

  If you want to share your cannon sweep feature, you will have to read the manual to see if it is possible and (b) how to put in place.  He usually just is to use the Canon CD to install the printer and its software required on your laptop the installer knows that the Canon is a shared network resource.

  The best and simplest is to buy a wireless router. In this way you
  get Internet connectivity both machines and the added benefit of some
  more security between you and the Internet. Next, you set up your wireless network
  network in any security, and then you configure file/printer sharing. Below you will find
  information on the implementation of a router and also in networking. Looks like
  long but don't be intimidated. Setting up a router and local area network
  sharing between two computers takes about 15 minutes.

  Configuration of the router.

  Setting up a router is simple enough. Normally, you run the CD that came with
  the router and follow the instructions. If you're running Vista may be the
  CD that came with the router does not work; I do not know this. But you can set
  the router without the CD. Note that if you have Internet, cable for the
  connection you just put the router to DHCP (or there may even be a)
  cable choice to choose). If you have DSL Internet, you generally
  Select PPoe and enter the username and password you chose during
  initially setting up the DSL connection. So:

  1. turn off the power to your cable modem.
  2 set a course of ethernet cat5e cable (usually supplied with the router)
  the port of the router to port Internet/WAN modem ethernet cable.
  3. connect the CAT5e cable from your computer's network card ethernet cable
  one of the ports on the router. If you do not have an ethernet cable
  (because you were using USB), you will need to go to the store and buy a.
  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

  Have a computer connected to the router with an ethernet cable. Examples
  given are for a Linksys router. Check the manual for your router or router
  site Web de MFTR. for the parameters by default if you don't have a Linksys. Open a
  browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (this is by default the router address IP, who)
  varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is left
  Blank and the Linksys default password is "admin" without the quotes. Come in
  This information. You are now in the configuration of the router utility. Your
  utility of configuration may be slightly different from mine.

  Click the Administration link at the top of the page. Enter your new
  password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Enter it again
  password to confirm and click Save settings at the bottom of
  the page. The router will reboot and show you the box of connection again.
  Do not fill in the user name and put it in your new password to return in the
  configuration utility.

  Now, click on the link wireless at the top of the page. Change the wireless
  Network name (SSID) default to something you will recognize. I have
  suggest that my clients do not use their surname as the SSID. For example,.
  You may want your "CastleAnthrax" wireless network name or the
  as. ;-)

  Click on save settings and when you get the prompt that your changes have been
  successfully, click the wireless security link which is just next to the
  Wireless settings link base (where you changed your SSID). If you have a
  Newish computer, you will be able to affect the Security Mode
  WPA2-Personal. Do this and enter a password. The password is what you
  come on all the computers that are allowed to connect to the radio
  network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you are using
  to configure the router normally goes for a wireless connection, unplug
  the ethernet cable and wireless of the computer should see your new
  network. Enter the password you created to join the network and launch
  Surf.
  *****

  B. file/printer sharing of

  Excellent, comprehensive, but easy to understand article on file/printer
  Sharing in Vista. Contains information about sharing printers and files
  and folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the network on all machines (see Setup Wizard
  caveat in section A below).

  Problems sharing files between computers on a network are usually caused
  (1) a misconfigured firewall or neglected (including a stateful firewall
  Firewall in a virtual private network); or (2) inadvertently running two firewall such as the
  Built-in firewall of Windows and a third-party firewall; and/or (3) not having not
  accounts of the same users and passwords on all computers in the workgroup; (4) try
  to create actions where the operating system is not.

  A. configure the firewall on all machines to allow the local area network (LAN)
  traffic as being approved. With the Windows Firewall, it means which allows file / print
  Sharing on the Exceptions tab normally run the Network Setup Wizard on
  XP will take care of this for these machines. The only "witch hunt" is that this
  lights on the XPSP2 Windows Firewall. If you are not running a
  third-party firewall or have an Internet Worm antivirus «»
  Protection' (like Norton 2006/07) which acts as a firewall, then you are
  fine. With a third-party firewall, I usually set up the allocation of LAN
  with a range of IP addresses. E.g. would be 192.168.1.0 - 192.168.1.254. Of course, you
  substitute your correct subnet. Do not run more than one firewall. DO
  NOT DISABLE THE FIREWALL; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This
  is from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not have
  must be connected to the same account on all machines and passwords
  assigned to each user account may be different. accounts/passwords just
  need to exist and to match on all machines. DO NOT NEGLECT TO CREATE
  PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to start directly
  on the desktop (a particular user account) for convenience, you
  to do this. The instructions on this link work for XP and Vista:

  Configure Windows to login automatically (MVP Ramesh) -.
  http://WindowsXP.MVPs.org/Autologon.htm

  D. Si one or more of the computers is XP Pro or Media Center, turn off
  Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not home users sharing
  directories or files of program, but you can share folders inside those
  directories. A better choice is to simply use the Shared Documents folder.
  See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a)
  files between machines), if you want to share a printer connected
  locally to one of your computers, share it to this machine. Then go
  for the mftr printer Web site. and download the latest drivers for the
  correct system. Install them on the target machines. The
  printer must be collected during the installation procedure. If this is not
  install the drivers, then use the Add Printer Wizard. In some cases,.
  Some printers need to be installed as local printers, but it's outdoors
  This response.

• SOLUTION for your HP printer disconnect and/or constantly disconnecting from the network

  If you are having a problem printing, scanning or fax with any HP printer because of this be disconnected and constantly disconnecting from the network, here again is the fix!

  I thought that this all after several failed attempts with HP Support, my Internet access provider and various troubleshooting tasks including reinstall the HP software and more and more.  Well, through self teaching on internet and exhausting search for 6 months, I FINALLY thought to it.  OMG!  I'm a paramedic (not IT) and a little computer but far not an expert.  I have all of you here!  Nobody seems to have the answer, but I'm sure that I'm doing it to 97%.  Whatever it is, if it please answer and let me know that it worked for you!  :-)

  It doesn't matter if your printer is installed cable or wireless.  You don't reinstall your software, no recycling power of your printers or your router/Modem.  Your printer is unstable on the network and continues to log out or disconnect from the network it is NOT because the software is glitched, it isn't a firewall problem by saying, is not a router problem, is not a problem with your power cord, because most networks use a 'Beach' and IP addresses for security reasons This kind of "cycles" the IP addresses of the devices to reduce the risk of an attack.  A printer is not a threat, but the 'network' don't own human intelligence, so he does not know this.  Here are my step by step instructions on how to basically your printer address IP (static IP) instead of change back through a cycle so drop your printer on the network or disconnected.

  Funny, if you're someone who has had the elements in your print queue, they will not print, and you turn your printer off and on again and suddenly your print... well documents, join my club.  The reason it works is that when you turn on the printer, it starts with the same IP address before cycle.  If you are someone who is sitting there for a while and all of a sudden your printed documents without changing you something... it is because through the cycle of change of IP address, it hits your printers IP address and the network would allow him to print.  Not very funny, I know.  It took me forever to figure out why my printer would print sometimes, but not always.  Since I thought at this point, I can SCAN, PRINT, and use all the features of my HP software installed like HP, Photosmart Essentials Solution Center.

  On your printer, go to menu/Setup/network and press OK.  In the network menu, print a "network configuration page" so you can see the IP address and other settings of your printer.

  Now, back to the main menu on the screen of your printers.  Or you can go to your web browser and type the IP address using decimal numbers too and this will take you to the web page of your printers.  Choose: setup\network, then press OK.  Look for the IP settings and press OK. Choose "manual" instead of "automatic". Manually enter the IP address it as well as the default gateway that you can see the Network Setup page you printed earlier.  Note: If you manually set the IP Address of the printer, make sure that it is outside the range of your router's DHCP. Otherwise you might encounter a problem with IP addresses on your network duplicate. (If you don't know how to do this, write back and I'll explain).  Don't forget to click "save changes".  Now, restart your computer, and print just what you want.  :-)

  A trick I often use with DHCP network printers:
  In printers and faxes, right-click on the printer and select "Properties".  Click Add a new port.  Choose standard TCP/IP port configured for the host name of the printer. Read the host name of the network printer configuration sheet.
  
  Using my method means that you always connect to the printer even if its IP address changes (which can happen with the dynamic configuration). This does not jeopardize the security of your network.  It shows just your printer to stay put and stop traveling the highway of IP address.  :-)

  The DHCP range is the range of IP addresses that the router distributes automatically as devices to join the network.  The DHCP range is determined by the router and each brand has a range that is set at the factory (which can be changed by you).

  Default value for the DHCP of your D-link is 192.168.0.100 to 192.168.0.199.  Thus, outside the DHCP range est.2 a.99.200 a.254.

  Is a handy cheat sheet attached.

  You can change this interval by entering the router settings page - type the router's IP address in a browser, enter the login information and access the DHCP parameter area (varies depending on router, hunting around).

• TouchSmart 610: TouchSmart 610 lights. I have a set of 5 beeps with a yellow light above the power button.

  I keep my office earlier this morning with the entry of the normal shutdown process. When I went to reactivate tonight all I get is a set of 5 beep with a yellow light flashing above the power switch. Repeat this five times then beeps stop and only yellow continuous flashing. I can hear and feel the hard drive running. I tried to unplug the power supply and then plugging, but the same thing happens. If I push and hold the power button on, it sounds like the hard drive stops and restarts. The normal blue light comes on for a few seconds then turns off and is replaced by the yellow flashing light. All you have no idea as to what may be the issue?

  Hello:

  Normally 5 beeps means there is a problem with the memory.

  I suggest that you remove and reinstall the memory modules and blow up if this doesn't fix the problem, if your PC has two memory modules, an and see if the beep disappears.

  If this is the case, remove this module and specify the first condition in you removed and if the beep begins once again find the defective memory chip.

  If it is not, remove the module and put the other in you deleted and if the ringing stops, you have found the faulty memory chip.

  Then replace the faulty memory module by one with the same specifications.

  If the ringing continues despite trying these steps, and then either the two chips of memory are bad (unlikely), or the motherboard has a problem.

• 5530 multifunction printe envy: want to set up the remote printer 5530

  Hello

  I have a printer Envy 5530 (new, never used or put in place) and I would like to use it to print remotely from my tablet. My tablet is running Android 4.2.2.

  I DO NOT have a computer and would like to know if there is a way to set up this printer to print remotely from my Tablet without needing to use a computer in the configuration.

  My tablet is currently connected wireless to my router which is not vacant ports Ethernet open if they needed to be able to print (although do if completely wireless would be preferred.)

  Thanks for any help anyone can give me.

  Hello

  You can attach your printer HP Envy 5530 to your existing wireless network, and then

  (a) use Google Play/store to install HP ePrint app on your Android device to print when the TWO are on the same network.

  (b) that your printer is also an ePrint printer. You can send an email to the email address that you want to print (supported file formats) when you are away from home

  Copy the following information to connect to your wireless network

  www.YouTube.com/watch?v=kOUA2t7lJlk

  Kind regards.

• Add on your HP printer connected account failed

  I had to send my first HP printer rear print quality was defective.

  So, I get a new printer and have not been able to set up properly.  Sometimes, he says that it is offline, but very clearly.  I deleted all the software and tried to reinstall, who got running initially.  Today, he said that he had no connection with my computer.  Yet once you remove all the software to try sorting.  It gets to a certain point and then said

  Add on your HP printer connected account... successful

  When I implemented the second printer in the fact that I tried to put the address printers, but he said he was already in use.  I think it is all confused...

  Help, please...

  If you talk about your account (email address) ePrint, you can not use it again that it is already used.  You must start over and get a new address of email ePrint.

• HP Color Laser Jet CP1215: print - guard 'book light' flashing - printer stops charging of paper does not alter

  Hello!

  For about a week, I have the following problem with my HP Color Laser Jet CP1215: after 2-3 pages of printing, the device stops abruptly in the middle of a job and the light number 5 (paper) continues at the flashing light.

  However, the bin is full with paper.

  Ignitions and extinctions help only for another 2-3 pages, then printing will stop again as described above.

  Is there maybe a photoelectric cell that needs to be cleaned or a mechanical part that gives the status of bad paper from the paper tray to the printer?

  Thanks in advance for any help,

  Best wishes

  Herwig

  Hi @wigl,

  Welcome to the Forums of HP Support!

  I see that your HP Color LaserJet CP1215 printer stops printing when the print jobs. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I can see how frustrating it would be. To determine the cause, we need to use more than one document. Redundant that some steps may seem, I would execute all.

  Please, try the steps in this these guides:

  • HP Laserjet CP1215 and printers CP1217 - 'paper ' Error Message is displayed and the printer does not look upward or feeding paper.
  • The Paper Jam flashing on HP Color LaserJet CP1215, CP1217 printer.

  If the problem persists, try a hard reset:

  • Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  • Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
  • Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!