Setting up with AT & T

Hello. I live in England and I am trying to set up my girlfriend with internet access, who lives in the United States. She has AT & T with a DLink modem. We have both found support DLink as useless, and AT & T have not been helpful either, two of them pointing us toward each other. In the United Kingdom, I use a wireless router with ADSL modem built into it, but it seems that it is more popular in the United States to have the modem under a separate post. I don't know if there is a reason for this? Currently, she has a pc connected directly to the modem (without router) and has a bridge put in place. I know absolutely nothing about bridges, because I've never had to use a. What is the best way for it to go? Does anyone have advice for me? The configuration is a nightmare, that can sit in front of the computer and she has no knowledge of networks and internet access. My instinct is to go for the WRT160N, which contains the DSL modem, but maybe I'm wrong. Does anyone know if there are specific parameters that need AT & T? Thank you.

The router (WRT160N) doesn't have a built-in DSL modem... However, you can use your modem AT & T connected to the router WRt160N having internet (wired and wireless)... You must connect the AT & T modem to the internet port of the router WRT160N... You must configure the Linksys router using this link

Tags: Linksys Products

Similar Questions

I have a new backup disk (a disk of 5 TB of Seagate) and need help setting up with CCC!

Hello world

I have a new backup disk (a disk of 5 TB of Seagate) and could use help setting up with CCC.

I did in the past without problem, but I want to assure you of a few things:
One last piece of information: two computers, etc, were all backed up via Time Machine. My data the most important, photos, etc., are also saved on deposit box and/or iCloud on a regular basis.

Thanks for any suggestions or comments!

Sally D.

Delete and partition the drive by making a separate partition for each computer. The iPad and the iPhone is useless their own partition because they back up using iTunes and would appear in the clone of the computer that you use for each save. Each partition must be the size of the current cloned drive that can leave you with additional partitions for other stuff. Then format the drive Mac OS Extended journaled. Do not install any software that came with the drive, none of this is necessary.

I use a very similar setup with a 3 TB drive. I clone my boot SSD in a single partition, my drive internal 1 Tb in a second, my Macbook to a third party, and I have a fourth partition which is currently empty, because I haven't decided what to do with it yet. I also have a 3 to Apple Time Capsule.

Can I use arrowheads and figures to be the custom shape set come with photoshop in graphic design that will be put on Youtube?

Can I use arrowheads and be in numbers the the custom shape set come with photoshop in graphic design that will be put on Youtube or social networking?

Hi albert xu,.

Greetings!

Yes, you can as this is why photoshop is intended.

You can use and create designs and post that publicly.

Concerning

Jitendra

A friend used my computer and sync is set up with HIS email, and I would like to delete that and put in my e-mail address.

I don't remember set up sync ACCT. But am not computer savvy (can get). Check Sync and discovered an acct is set, but not with my email. My friend used my computer and I don't know if she wanted to do, but now ACCT. is his email, and I would like to change this, but am afraid to delete all data and make a slurry of something already messed up.

Use: Tools > Options > synchronization > ungroup this device

Need help setting up with a projector.

Hello
I have a M30X & seem to be unable to set up for use with a projector. I can get it to show the theme of office & my pointer of the mouse on the projection screen, but nothing else. I don't see any program on the projection screen & I want to use it to make PowerPoint presentations. I tried all the basic tips including the wizard, but no luck! Help please.

Hello Lizzie

It's very strange that there is no possibility to see any program started on projector. As far as I know if PowerPoint contains some copy protected files, it is not possible to be shown.

iCloud Keychain could not be set up with a valid entry

I use iCloud Keychain for a while now, but last year I worked on a computer not apple. There was therefore no need to sync, so I ignored when he asked me to check my account for her information.

So now I'm back to Mac and I want to synchronize my Wi - Fi passwords with my iPhone. I tried configuring iCloud Keychain (I know the security code and I have access to my phone), but it fails on both my Mac and iPhone. The data there are really outdated, so I decided to reset it and create a new keychain, but I found only the options for that when it is turned on.

What do you think that the issue can be? And what can be the solution?

Notes:

-below are the error messages I get

-J' tried to set up for weeks now, is not a server failure. Also different networks.

-I know that the right security code, and I have access to the phone number, if I get the verification code too.

"iCloud Keychain could not be restored because there was a communication problem with iCloud. .

Try restoring iCloud Keychain again. "on a Mac

"One could not Set Up iCloud keychain" on an iPhone

Hello Balint,

Looks like you've tried some, but not all, the steps of troubleshooting for the issue you are seen day or setting to the top of your iCloud keychain. Take a look at the resource below to this address. I have highlighted some information for you here, but click on the link for more details.

Get help using iCloud keychain
If you cannot synchronize iCloud Keychain with other devices

Make sure that your device is on a Wi - Fi or the cellular network. If the connection seems strong, try the following steps:
1. Turn off iCloud Keychain on all devices.
2. Turn on iCloud Keychain on the device that has the most up-to-date keychain items.
3. Turn on iCloud Keychain on your other devices. They will be updated with your iCloud new keychain.
If you no longer have your iCloud keychain items

If you disabled iCloud Keychain on all your devices, your iCloud Keychain is removed from the Cloud. If you have chosen to remove the keychain of your devices when you have disabled iCloud Keychain, your iCloud Keychain is also removed from these devices.

You will need to install iCloud keychain and add items again. Apple cannot recover your iCloud Keychain if you turn off iCloud Keychain on all your devices and choose to remove your iCloud Keychain locally on all your devices.

On OS X, if you used Keychain Access to reset your OS X Keychain, OS X will delete your iCloud keychain items. Choose Keychain Access > S.o.s. keychain to verify and repair keychain settings and permissions. If this does not help, reconfigure iCloud keychain. If you need to reset your OS X Keychain again, temporarily disable iCloud Keychain in iCloud preferences before resetting your OS X Keychain.
Take care

NOR error-89136 property set DAQmx_RefClk_Src with value/PXI1Slot2/PXI_CLK10

Dear members of the forum OR,.

We have just received a chassis NI SMU-1073 with an SMU-6361 OR switched in PXI1Slot2 and a shielded connector BNC-2111. Aims to trigger two output signals to control a laser and a sound via Matlab Application.

Version of Matlab is 8.2.0.701 (R2013b) and data acquisition toolbox is 3.4. Installed is the 9.8.0 driver NOR-DAQmx. We followed the example of the tutorial on the web page of Matlab to generate output. The code establishes a connection with a device, it creates a session and adds an output channel. Once this is done, the session is started in the foreground, but it fails with the following error massage:

OR error-89136:

Specified route can not be satisfied, because the hardware does not support.

Property: DAQmx_RefClk_Src

Requested value: / PXI1Slot2/PXI_CLK10

Based on some forums, we checked the route tab of device in Explorer automation and PXI_CLK10 signal is almost yellow everywhere. Looks like he expects, as a reference, the PXI_CLK10 clock, but there is no direct route to it. On the other hand, there are PXIe_CLK100 that is green.

Question is how through Matlab interface based session one can set the reference clock signal? Or y at - it another way to solve this error? Maybe another type of configuration is necessary?

Tips, drivers, and solutions are welcome!

Thank you in advance!

see you soon,

go9kata

P.S.: the same question has been added three different times to Matlab support page, but there was no response to all the

http://www.MathWorks.de/matlabcentral/answers/107494-acquire-synchronized-data-using-PXIe-devices

http://www.MathWorks.de/matlabcentral/answers/37134-data-acquisition-from-NI-PXIe-1062Q

http://www.MathWorks.de/matlabcentral/answers/112626-national-instruments-data-acquisition-software-...

Hi all

the last questions are displayed also here and replied:

several finite pulse trains of TTL

Set up with ink

I gathered my printer to work ready to work at home. I installed on the computer and its ready to go. But when I came to install the ink cartridges lacked the 950 - I went to the store and bought the only one they had, a 950XL, but now the printer won't allow me to set up because it's not the cartridge supplied with the printer. I really need to go to my job, I can work around this problem, you?

You need to call HP telephone support on this issue, since the printer must be initialized with cartridges SETUP.

Phone numbers

http:// Welcome.HP.com/country/US/en/wwcontact_us.html

Can you please let us know once that they solve it for you?

Thanks, Ciara

Windows Media Center cannot sync/set up with AT & T UVERSE

Windows Media Center cannot configure/sync with my cable TV box. ((See system put in place/info below)

I spent about 10 hours trying to solve this problem. Tried every way Windows Media Center allows you to configure, automatic, manual (tried all listed codes), IR remote learning. I searched the web, talked with HP technical support for more than 3 hours, talked with Motorola, ATT UVERSE, someone seems to have a solution. Based on troubleshooting, I have it so far, I'm a 90 + % sure it's soley configuration of Windows Media Center TV of UVERSE problem of decoder.

I can get a TV signal on the computer through Windows Media Center and get my cable TV box to make it work, but it's as close as possible. The remote control works, all connections are correct, IR blaster or transponder is located correctly on my TV receiver.

In the IR remote control learn installation manual configuration (I think this is one of the two) or Windows Media Center asks you to press and hold the "0" on your remote decoder, pointing to your receiver IR from PC. When I press on it it seems to answer by saying to continue to hold then it ask you to release what I'm doing, then I get an error message. It is the closest, I learned to operate. I tried a few tricks/variations on this that I found on this site and others, but not luck.

Another question the image that I get, but cannot control with Windows Media Center is of very poor quality (worse than a bad cell phone video on youtube), I guess that's more hardware related issue, but I had a machine good enough speced. Also, there is a time delay major and variable (4-5 seconds) between the time you press a button on the decoder TV and you see the answer on the machine, which makes it very difficult to operate.

I keep trying to stay on the PC band wagon, but of course, the other side seems to be much less difficult to get simple things to work.

Anyadvice is appreciated.

COMPUTING: NEW HP Desktop (updated all the software) - Windows 7 Professional - 1 GB ATI Radeon HD 4850 - TV tuner, ATSC-NTSC with PVR, remote - Intel i5 - 8 GB of SDRAM. TV SERVICE: AT & T Uverse - Motorola VIP1200 box

http://www.eggheadcafe.com/software/ASPNET/30978261/att-UVerse-and-Media-Center.aspx

the post titled "hey guys" posted August 8, 2009 should help out you. I managed to set up my own using the info there. Poor quality looks like a standard old school SD tuner in your pc.

Hunt group type Set up with outdoor extension numbers IE cell phones

With the help of CUCM 9.1

Is there a quick and easy way to create a type of fighter group set up to help on the outside (cell phone numbers)?

The scenario will be a (person who will be on call) using an internal DID to be forwarded to a cell phone of the person oncall this particular week. If no response she pass 4 members to the next line and also try their cell phone. After that it would just repeat the whole process. So far, it looks like a solution is possible with the single line scope perhaps?

Any ideas would be grealy appreciated.

Dave

Hello

I put something like this on CUCM 8.0 a couple of years.

I used the Mobile connection feature as you suggested and it worked ok after some playing with timers.

The main problem was that it was impossible for remote users to disconnect to the hunt group. They could disable Mobile Connect using the IVR, but calls would still ring on their deskphones - if you log on phones (i.e. Extension mobility) before leaving the office this problem should appear.

The other question was how long calls to connect especially if a couple of people in the Group has not responded. In fact, we recorded a message asking callers to be patient, which was played when the call was received first (we were using UCCX to IVR and call transfer).

I hope this is of use.

Variable setting wrong with dynamic action for the region of report

Hello
I can't setting a variable. Here are the details of connection:
Connection information:
TCARMY workspace
User Apex_dev
Password dev_apex
Application 88542
Page 11
If you run the page 11 and just click on submit, there will be two rows. If you click on one, the modal region won't say no data found. If you click on the button submit once again, the value is passed if you click on it now, the results arrive. If you click on the second row, it still shows the value of the first row. If you click on submit again after clicking on the second line, then it is displayed correctly. It seems that the value is set to submit it. I want this to work when clicked, and then for the sql to run with the value that is in this variable when clicks on the element. There is a bit of javascript page level and dynamic action. Something is not right to the installation.
The modal window should popup and run the sql at that time with the variable data and view the two columns. And if the user clicks on the second row, it would display the data in the row.

Thank you
Tim

TC-army wrote:

If you run the page 11 and just click on submit, there will be two rows. If you click on one, the modal region won't say no data found. If you click on the button submit once again, the value is passed if you click on it now, the results arrive. If you click on the second row, it still shows the value of the first row. If you click on submit again after clicking on the second line, then it is displayed correctly. It seems that the value is set to submit it. I want this to work when clicked, and then for the sql to run with the value that is in this variable when clicks on the element. There is a bit of javascript page level and dynamic action. Something is not right to the installation.

What has not been set up right, it's that the element of P11_NAICNUMD parameter was not specified in the source attribute of Page to go to the region, modal Discount. The current value in the browser page, therefore, was not defined in session state when the report has been updated by the dynamic action. When

Trying to save a film set up with Adobe Premiere Pro on a DVD to play on DVD player...

I am trying to record a film shot in Premiere Pro on a DVD to be played on a DVD player. I tried all the formats do not work, I use a DVD-R disc, tried to save in Media Encoder as well to change it to see if there is a difference. I am new to Premiere Pro and encoder, so I wonder if I missed a step somewhere...

A DVD must be "created" - you do not just burn a multimedia file on the disk. Data must be encoded somehow, some folders, flags on the disc structure, etc. in the order so he could answer DVD spec to play for set-top players.

You will need to export using the appropriate "MPEG-2 DVD" format and preset, then hold these assets Adobe CS6 Encore authors a DVD. Still is not included with the CC, but you can always download it, see the instructions here - CS6 still not installed with creative cloud

Thank you

Jeff Pulera

Safe Harbor computers

Set session with past date in oracle

Hi Experts
about us / request zone of the Pacific of a column, we establish sysdate value for the column.
setting sysdate, I use under sql so that he should take care Photonics day save and no light of day.
cast( from_tz( cast( SYSDATE as timestamp ), 'US/Pacific') at time zone 'UTC' as date)

Date today I tested, its gives me the correct value, but for the test date when day light economy performed as June 25, 2013.
I wanted to define after date for my session and do some tests.
could if it you please let me know sql for the session with over date formatting.
Thanks 4 your help!

Change the time on the server running Oracle.

Strange comment about persistent RMAN setting, stands with views v$
Version of DB - Oracle Database 11g Enterprise Edition Release 11.2.0.1.0

I was checking configuration RMAN in cartoon as below: -.

RMAN > show all.

using the control file of the target instead of recovery catalog database
Database with db_unique_name ORCL RMAN configuration parameters are:
CONFIGURE REDUNDANCY 1 RETENTION STRATEGY; # by default
CONFIGURE BACKUP OPTIMIZATION # by default
SET UP DEFAULT DISK DEVICE TYPE; # by default
CONFIGURE CONTROLFILE AUTOBACKUP # by default
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # by default
SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default
CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default
CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default
CONFIGURE MAXSETSIZE TO UNLIMITED; # by default
CONFIGURE ENCRYPTION OF DATABASE # by default
CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default
CONFIGURE COMPRESSION ALGORITHM 'BASIC' AND 'DEFAULT' LIBERATION OPTIMIZE FOR TRUE LOAD; # by default
CONFIGURE THE NONE ARCHIVELOG DELETION POLICY; # by default
CONFIGURE SNAPSHOT CONTROLFILE NAME TO ' / u01/oracle/app/oracle/product/11.2.0/dbhome_1/dbs/snapcf_orcl.f'; # by default

The same parameter should be reflected in v$ rman_configuration according to the docs of Oracle, however check below: -.

SQL > select * from V$ RMAN_CONFIGURATION;

no selected line

Why the discrepancy in these settings, ideas?

Published by: 918868 on January 22, 2013 20:53

Published by: 918868 on January 22, 2013 20:54
I was checking configuration RMAN in cartoon as below: -.

RMAN > show all.

using the control file of the target instead of recovery catalog database
Database with db_unique_name ORCL RMAN configuration parameters are:
CONFIGURE REDUNDANCY 1 RETENTION STRATEGY; # by default
CONFIGURE BACKUP OPTIMIZATION # by default
SET UP DEFAULT DISK DEVICE TYPE; # by default
CONFIGURE CONTROLFILE AUTOBACKUP # by default
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # by default
SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default
CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default
CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default
CONFIGURE MAXSETSIZE TO UNLIMITED; # by default
CONFIGURE ENCRYPTION OF DATABASE # by default
CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default
CONFIGURE COMPRESSION ALGORITHM 'BASIC' AND 'DEFAULT' LIBERATION OPTIMIZE FOR TRUE LOAD; # by default
CONFIGURE THE NONE ARCHIVELOG DELETION POLICY; # by default
CONFIGURE SNAPSHOT CONTROLFILE NAME TO ' / u01/oracle/app/oracle/product/11.2.0/dbhome_1/dbs/snapcf_orcl.f'; # by default

The same parameter should be reflected in v$ rman_configuration according to the docs of Oracle, however check below: -.

SQL > select * from V$ RMAN_CONFIGURATION;

no selected line

Why the discrepancy in these settings, ideas?

V$ RMAN_CONFIGURATION displays the default settings

Set preferences with script

I want to distribute the Adobe reader on a server terminal server and limit users to change the configuration. I need to uncheck 'cross-documents links open in the same window. I'm hoping to do it with Javascript.
Does anyone know how to do this?
Thank you
Jeff

Thanks Ben. It was exactly what I need. I wa able to write a batch file that imported time touches the first, the user connects.

The other parameters were not specific user (for example to prevent the update), so I am able to set up a time for the computer.

Thanks again.

Jeff

Setting up with AT &amp; T

Similar Questions

Get help using iCloud keychain

If you cannot synchronize iCloud Keychain with other devices

If you no longer have your iCloud keychain items

Maybe you are looking for

Setting up with AT & T