Several bsod after clean windows 7 installed

Similar Questions

• Cannot install the update for Windows vista (KB2718704) a safe mode or after clean window reboot

  I can't install the update for Windows vista (KB2718704), a mode without failure or after clean window reboot.

  What should I do?

  Hello

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         You are able to install other updates successfully?

  Follow these methods.

  Method 1: Temporarily disable the security software .

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Put the computer in a clean boot State to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow step 7 the link to start the computer to a Normal startupmode.

  Method 3: You can also manually install updates (KB number) by downloading from the Microsoft Download Center.

  http://www.Microsoft.com/downloads/en/default.aspx

  Method 4: Follow the steps in the article.

  How to reset the Windows Update components?

  You cannot install some programs or updates

  Note: You must take the backup of the data before performing any installation of windows.

• BSOD after Logo Windows at startup: bad driver, AutoFailover

  I get BSOD after Windows Logo at startup. Said Startup Repair: bad driver, AutoFailover.

  Two weeks ago, that I was getting the same BSOD after logo, but only with the bad driver. I not did something to fix it (or Startup Repair), it's just dissapeard after a few days. Also, the last day that I was getting BSOD, the night when I started my pc, it remained 2 minutes at Intel Boot Agent initialization and also 30 seconds to the black screen that follows (before the windows logo). When this situation occurs I get more BSOD. I tried to restart my pc but I stayed another 2 minutes to the Intel Boot Agent initialization. This problem has been fixed in the next morning, when I started my PC, even once, I don't know how, I did nothing. I remember that it is sometimes used to stay 2 minutes Intel Boot Agent, even when I was on Windows Vista, and it also sets automatically.
  I upgraded my BIOS a few weeks before getting the BSOD, but I don't think that's the problem. In addition, there was no new driver installed before getting the BSOD, drivers have been installed after the first BSOD (even if the event viewer and the reliability monitor do not mention the first BSOD, only those who have followed the installation of the driver I know there's a BSOD before, I'm sure.)
  My system: HP Compaq 8510w (Original with windows vista bussines, did a clean install of 7 ultimate)
  BIOS version: F.20

  C: drive has only 10% free space - 15% free space is optimal for Windows

  Please visit the site Web of the manufacturer of the PC and download/install all drivers.  These are devices that lack the drivers:
  *******
  Controller of communication Simple PCI PCI VEN_8086 & DEV_2A04 & SUBSYS_30C5103C & REV_0C\3 & 21436425 & 0 & 18 that the drivers for this device are not installed.

  Serial port PCI PCI VEN_8086 & DEV_2A07 & SUBSYS_30C5103C & REV_0C\3 & 21436425 & 0 & 1 b, that the drivers for this device are not installed.
  No available ACPI\HPQ0006\2 & DABA3FF & 2, the drivers for this device are not installed.

  Base system device PCI VEN_1180 & DEV_0843 & SUBSYS_30C5103C & REV_10\4 & 118B1C9 & 0 & 34F0 the drivers for this device are not installed.

  Fingerprint Sensor USB\VID_08FF & PID_2580\5 & 1E4845E3 & 0 & 2, that the drivers for this device are not installed.

  RICOH PCMCIA\RICOH-BAY8CONTROLLER-F1B2\1 Bay8Controller the drivers for this device are not installed.
  ******
  Please uninstall ATI Tool - it does not work in Win7 and may be responsible for your BSOD (and its drivers are from 2006).  More info here: http://www.carrona.org/drivers/driver.php?id=ATITool.sys

  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  BSOD BUGCHECK SUMMARY
  The debugging session: 05:54:32.426 Fri 31 August 2012 (UTC - 04:00)
  Loading dump file [C:\Users\John\_jcgriff2_\dbug\__Kernel__\083112-17019-01.dmp]
  By: 7601.17803.x86fre.win7sp1_gdr.120330 - 1504
  System Uptime: 0 days 0:00:08.455
  Bugcheck A, {7bcc, 2, 0, 82afb482}
  ERROR: Module load completed but symbols can be loaded for mssmbios.sys
  Probably caused by: ntkrpamp.exe (nt! DeleteNodeFromTree + 46)
  Error checking code 0000000-a
  Arguments 00007bcc ', memory IRQL bitfie 82afb482 00000000' 00000002',' address
  DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT
  BUGCHECK_STR: 0XA
  Nom_processus: System
  FAILURE_BUCKET_ID: 0xA_nt! DeleteNodeFromTree + 46
  MaxSpeed: 2200
  CurrentSpeed: 2194
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  The debugging session: 04:17:05.296 Thu August 23, 2012 (UTC - 04:00)
  Loading dump file [C:\Users\John\_jcgriff2_\dbug\__Kernel__\082312-17004-01.dmp]
  By: 7601.17803.x86fre.win7sp1_gdr.120330 - 1504
  System Uptime: 0 days 0:00:11.356
  CD error checking, {8931d 000, 0, 82a271f2, 0}
  ERROR: Module load completed but symbols can be loaded for mssmbios.sys
  WARNING: Unable to verify timestamp for ATITool.sys
  ERROR: Module load completed but symbols can be loaded for ATITool.sys
  Probably caused by: ATITool.sys (ATITool + 2017)
  000000cD Bugcheck code
  Arguments 8931d 000', memory 00000000' 82a271f2 value ', if not 00000000', int Mm
  DEFAULT_BUCKET_ID: VERIFIER_ENABLED_VISTA_MINIDUMP
  BUGCHECK_STR: 0XCD
  Nom_processus: System
  FAILURE_BUCKET_ID: 0xCD_VRF_ATITool + 2017
  MaxSpeed: 2200
  CurrentSpeed: 2194
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``
  The debugging session: 04:00:26.646 Thu August 23, 2012 (UTC - 04:00)
  Loading dump file [C:\Users\John\_jcgriff2_\dbug\__Kernel__\082312-21933-01.dmp]
  By: 7601.17803.x86fre.win7sp1_gdr.120330 - 1504
  System Uptime: 0 days 0:00:07.675
  Bugcheck 1000007E, {c0000005, 82c2e4a4, 80786888, 80786460}
  ERROR: Module load completed but symbols can be loaded for mssmbios.sys
  Probably caused by: ntkrpamp.exe (nt! ObpLookupDirectoryEntry + 2 b)
  Bugcheck 1000007E code
  Arguments c0000005", ex-82c2e4a4 ', the 80786888 ad', except 80786460', Contex
  DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT
  Nom_processus: System
  BUGCHECK_STR: 0X7E
  FAILURE_BUCKET_ID: 0x7E_nt! ObpLookupDirectoryEntry + 2 b
  MaxSpeed: 2200
  CurrentSpeed: 2194
  ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨``

• Error 0 x 80070570 - clean Windows 7 install

  I'm trying to install Windows 7 Ultimate 64 bit on a new system. The Setup will as much as ' Windows files (1%) expanding... "and fails with the error 0 x 80070570. I spent 5 days trying to solve, read and tried all the suggestions on this forum, spoke with MSsupport, but nothing helped.

  The message full error is "Windows cannot install required files. The file may be corrupted or missing. Make sure that all the installation files are available and restatrt installation. "Error code: 0 x 80070570.

  The setuperr.log in Panther left directory after the installation says:

  2015-04-19 21:12:57, error [0x0600af] IBS ApplyWIMCallback: error application D:\Windows\winsxs\amd64_microsoft-windows-s... oxgames-purbleplace_31bf3856ad364e35_6.1.7600.16385_none_622070221822eb39\PurblePlace2.dll. RULE [1392] [gle = 0 x 00000570]
  2015-04-19 21:12:57, error [0x0606cc] IBS WIMApplyImage failed; HR = 0 x 80070570 [gle = 0 x 00000570]
  2015-04-19 21:12:57, error [0x0600a1] IBS DeployImage:Image request failed; HR = 0 x 80070570 [gle = 0 x 00000570]
  2015-04-19 21:12:57, Callback_ImageTransfer IBS [0 x 060082] error: unable to set the image; HR = 0 x 80070570 [gle = 0 x 00000570]

  I also saw the same error, but the file journal.dll on two attempts.

  Have you tried the original DVD, which came in the box, like any other with Widows 7 Home Premium, which I borrowed from a friend. The two systematically fail with the above error.

  I would really appreciate help with this problem. Please let me know what additional information can help diagnose.

  Just to try to identify the problem, download Windows 10 Technical Preview and try to install it to see if you encounter the same problem:

  Download and prepare Windows overview 10. ISO file (build 10041)

  There are several ways to start the installation of Windows 10, but before we even do however, need to ensure that we have our copy of Windows 10 downloaded and converted into a bootable copy.

  Download: Windows 10 10041 English: x 86 | x 64 | More versions

  Additional languages can be found here:

  http://Windows.Microsoft.com/en-us/Windows/preview-ISO-update?OS=win10

  Determine if the 64-bit or 32-bit is adapted to your needs:

  The following article will help you determine the difference between the two:

  64 bit 32 vs

  http://Windows.Microsoft.com/en-us/Windows7/32-bit-and-64-bit-Windows-frequently-asked-questions

  The article refers to Windows 7, but the same principles apply to Windows 10.

  Prepare the. ISO installation file.

  See the instructions for burning. ISO in Windows 7 or later files:

  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-from-an-ISO-file

  You can also use the Microsoft USB/DVD tool, which is recommended for users of Windows XP.

  After graduating the .iso file, you use the Microsoft .iso to USB/DVD tool to create a bootable DVD or USB (requires a blank DVD or USB flash to at least 4 GB key).

  

• A BSOD after loading Windows and before logon

  Hello

  I have a problem with my PC:

  The BSOD happens on the screen to login before I can enter my user name or password. of course the strong BSODS happened so windows worked.

  Please help me

  Here's my dump files:

  http://1drv.Ms/1QMLlC9

  Thank you

  Several questions

  First you need to update these drivers from 2005

  RecAgent.sys 10/05/2005 12:28:17
  wdcsam.sys 16/04/2008 03:27:02
  Apowersoft_AudioDevice.sys 18/11/2008
  L1C62x86.sys 2009-04-01 12:07:46 AM

  This accident was related to a COMODO Firewall Pro Sandbox Driver cmdguard.sys.  I would remove it years use MSE in its place

  http://forums.Comodo.com/help-for-v2/how-to-uninstall-Comodo-Firewall-t1184.0.html

  http://www.Microsoft.com/security_essentials/

• BSoD after updating Windows on Win7 Pro SP1 x 64

  So, yesterday windows had installed updates for my machine, but now when I turn it on, it crashes with this error

  PAGE_FAULT_IN_NONPAGED_AREA 0 x 00000050 (win32k.sys)

  I didn't install anything last time, it was only windows update itself

  Thanks for the reply

  Apparently my first answer could not be validated, so I'll try again:

  Its a known issue, see this post for a way to repair:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_update/blue-screen-Stop-0x50-after-applying-update/6da4d264-02d8-458e-89e2-a78fe68766fd

  Also:

  Customers who are unable to restart their computer after installation of this update can be found steps of resolution published in the section known issue from Microsoft Knowledge Base Article 2982791.

  J W Stuart: http://www.pagestart.com

• Clean Windows 7 install on questions of activation U500-1hd

  Hello

  I have a problem with my newly purchased 1hd U500 laptop. I didn't like the way the Manager auto partitioned hard drive, so I went ahead and all the formatted partitions and divide them according to my needs. The problem is that the laptop, even if it came with Windows 7 Home Premium 64-bit, had no Windows 7 install cd/dvd or any other ultility cd/dvd. I went and downloaded a copy of Windows 7 Home Premium 64 - bit Microsoft MSDNA, installed, but when I try to activate it using the cd - key on the sticker on the back of the laptop, it says invalid cd - key.

  I rechecked the cd - key, and I wrote it down correctly. It says on the sticker Windows 7 Home Prem OA. Do I need a special kit of Win7 or something?

  Thanks in advance.

  See [how to replace lost, Broken, or lack of Microsoft Software or Hardware | http://support.microsoft.com/default.aspx?kbid=326246] were MS say contact Toshiba.

  I don't know if W7 will allow this, but you used to be able to leave the key field blank and click next to install. You need to activate windows within 30 days, and at this point, there was a phone activation option. Try this option and MS can provide a new key or suggest you only send their proof of ownership. I just download Winguggle to see that my product key does not match the label of laptop - it is possible that activation of MS has changed and the program will not

• BSOD issues before and after a clean windows 7 installed

  Hey, I get BSOD issues after a clean install of windows and I also replaced my RAM with sticks again because I thought that my memory was damaged for some reason any. Is it possible that my hard drive is bad?

  Here's my minidump file:

  https://www.dropbox.com/s/paqnfyylg5yw2bw/012416-20420-01.dmp?DL=0

  Hello

  Since you did a clean install this strongly points to material with only one
  small chance, it is the BIOS, chipset drivers or others. Could be the hard drive, the
  wiring for the hard drive or other hardware.

  BugCheck F4, {3, fffffa800df48060, fffffa800df48340, fffff80002b97f40}

  ETW unavailable minidump
  Probably caused by: ntkrnlmp.exe (nt! PspCatchCriticalBreak + 92)

  Ntkrnlmp.exe is a component of Windows which means than anything else he has led astray.

  See this article:

  You receive various Stop error messages in Windows 7 or in Windows Server 2008 R2 when you try to resume a computer that has a large hard drive SATA.
  http://support.Microsoft.com/kb/977178

  ---------------------------------------------------------------------------------------------

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  ========================================================

  BCCode: F4 0x000000F4

  Check and reinstall the cards memory and cables (at both ends where possible) in fact
  delete and replace - do not just tight. On a laptop computer on all you can do is reinstall it
  memory and possibly check the connection/contacts on the hard drive. Memory could
  be the problem, so if you have more than 1 stick swap them in and out to see if the
  problem follows a stick or try the new memory. Antivirus/anti-spyware/security programs
  have been known to cause or have a role in this matter.

  More general patch updates day and low level chipset BIOS drivers and other software to control.

  Also check the wiring on the hard drive.

  =========================================================

  BCCode: F4 0x000000F4<-- read="" this="">

  * 1241.html http://www.faultwire.com/solutions-fatal_error/A-process-or-thread-crucial-to-System-Operation-has-0x000000F4-

  Bug Check 0xF4: CRITICAL_OBJECT_TERMINATION
  https://msdn.Microsoft.com/en-us/library/ff560372%28V=vs.85%29.aspx?f=255&MSPPError=-2147217396

  =========================================================

  These can help:

  Remove ALL power. Then carefully remove the cards one time and put them
  back in their locations. Do the same for memory, then the cables. A coward or
  corroded connection point may cause strange problems.

  Reinstall the expansion cards
  http://pcsupport.about.com/od/fixtheproblem/SS/Reseat-excards.htm

  How to reinstall a desktop memory Module
  http://pcsupport.about.com/od/fixtheproblem/SS/reseat_memory.htm

  The relocation of the supply and internal data cables
  http://pcsupport.about.com/od/fixtheproblem/SS/Reseat-power-cables-data-cables.htm

  Reinstalling your RAM, graphics card and hard drive
  http://www.YouTube.com/watch?v=DLxNPBQBfT8

  ---------------------------------------------------------------------------------------

  You may need to check with the mother system/card manufacturer or a computer
  Shop (that makes its own service in the workshop).

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• BSOD after updating Windows and it is not installed.

  A blue screen of death appears whenever I put it in sleep mode, standby time, turn it off or restart.  It happened from a windows update when I started it up after it stops after the update, and she appeared with another update.  He still wants to install the update, but it still gets a BSOD at the end.  The BSOD seems to point to usbhub.sys.  Thank you.
  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 1033
  More information about the problem:
  BCCode: 1000007e
  BCP1: C0000005
  BCP2: D 907 5013
  BCP3: ACF80B68
  BCP4: ACF80864
  OS version: 6_0_6002
  Service Pack: 2_0
  Product: 768_1
  Files helping to describe the problem:
  C:\Windows\Minidump\Mini042210-01.dmp
  C:\Users\office depot\AppData\Local\Temp\WER-113724-0.sysdata.xml
  C:\Users\office depot\AppData\Local\Temp\WER5DC8.tmp.version.txt

  You indicate that you get blue screen after the update is finished installing. Or do you find only the blue screen when you perform certain functions with the system which requires a State of transition of power (sleep, restart, etc.)?

  You've got bugcheck SYSTEM_THREAD_EXCEPTION_NOT_HANDLED caused an access violation.

  You can download the contents of c:\windows\minidump on your SkyDrive? The discharge can take probably a few additional details.

  To treat blue screens, following general tips:

  Consider running chkdsk on all partitions.  Leave complete chkdsk on each partition and see if that helps.

  Also consider running SFC/scannow.

  If you start in safe mode, do you still feel bugs? What if you do a clean boot, or boot device?

  Other common suggestions include ensuring drivers are up to date (including video drivers), but also to ensure that you use the latest version of the BIOS.

  Consider the memory with memtest86 or Windows Memory Diagnostic test. Note that memory that pass the tests isn't necessarily good memory - he not only failed a review.  Examine systematically to eliminate the system RAM - run with a few modules for awhile and see how things are going. Then try the other modules.

  For the case of memory corruption such as you seem to be experiencing, it may be useful to use Driver Verifier.  To activate the... Driver Verifier start-> verifier.exe-> OK-> create standard settings - > then-> the names of the drivers select in a list-> next-> sort by provider-> select all non-Microsoft drivers-> finish and OK your way out of the dialog box.

  Then restart and use the system as you normally and wait for a problem.  In case the system does not completely start after activation of the Verifier, boot mode safe and run driver verifier and tell him to remove the changes.

  Wait for an error checking to happen after you have enabled the auditor as described and then transfer it to your SkyDriveand provide a link.

• Don't Aspire Switch 10 no sound after clean windows install

  I installed a clean version of windows 10 (not acer windows) earlier and since then against hepatitis has ever had his fate of the speaker or headphone output port. If I connect to HDMI or use the bluetooth speakers it works, but it's pretty rare that I do and it is certainly not practical.

  The drivers are updated, ive tried reinstalling them, fitness again with windows, playing with the bios but it is very limited with what you can do. I was going to attempt to reinstall the factory windows version 8, but I can't know exactly how do.

  If I go to playback devices, he thinks it works. the sound bar changes when I play something but no sound.

  It is intel audio device (WDM) OSH if this is useful.

  you have any ideas how I can fix these problems?

  Thank you

  Go to Device Manager > view > show hidden devices. If you have other devices > IWD Aud-Device_6, uninstall it. Then restart your system. Go to Acer supports downloads of drivers for your model. Download Realtek Audio Platform Installer from pilots and quick access. Install Reltek and then restart the system. Install quick access, then restart. Finally install the drivers for the platform. Restart and you should have sound.

• HP pavilion dv 2700 notebook: driver coprocessor missing after clean windows 8.1 installed

  Original operating system was Vista.  Then uped to 8.1, worked great, although missing some programs.  Windows 10 resulted in a very poor video playback.  Tried to goback to 8.1, did not work.  Hard disk formatted, installed then 8.1 full version.  Now missing driver coprocessor. Impossible to find. Don't have original disk with Vista.

  Hello:

  When you see a coprocessor device, this means that your notebook is the processor amd and nvidia chipset.

  Install the chipset nForce Vista driver and you should be ready.  You may need to install manually if auto installation does not work.

  I don't see the correct chipset for any model dv2700 pilot, so use this one from a dv6700...

  This package provides the driver for the NVIDIA nForce Chipset AR in the notebook models and operating systems.

  File name: sp37730.exe

• Sales of portable computers: clean Windows OS install - no disks?

  Hey there-

  I looked for the knockout, but I couldn't find an answer to that particular question. most people want to reinstall their operating system on a laptop computer that they will keep. Mine is OLD and will be sold/given.

  I need to clean and (good manners!) and then reinstall the operating system on some old laptops for resale / donation.

  None of these laptops came with an OS disk.

  Can anyone tell better options?

  Do I have to buy the Windows operating system to install on both (which would be a brake...)?

  Can I download a version somewhere and do a reinstall drive?

  Is there a way to clean / reinstall these laptops with existing Windows accessories that are part of the laptop?

  Please note: these will have to be 'cleaned' first they will go to foreigners :)

  Thank you very much!

  JL

  PS Sorry if it is categorized properly and please let me know if I should post elsewhere :) jl

  Use the built in "recovery Partition ' of re - install Windows 7."

  Recovery of your computer (Windows) using "Recovery Partition" of the Manufacture or
  contact PC manufacturing (see support links below) and order the recovery media.

  Note: Activation is not required when you use the recovery partition or recovery media, but you will need to reinstall all your applications.

  Once completed, your PC will be actually in the State when you first purchased it and turned on for the 1st time.

  To access the recovery Partition, start your computer, and then by pressing the appropriate function key. It can be either F1, F2, F9, F10, F11, F12, DEL or tab key. Check the list below or your user manual for your brand and model.

  If your hard drive has failed, do not have a recovery partition or the recovery partition is not accessible,
  Then, you must contact the manufacturer support team and ask for a "recovery disc" which allows to reinstall Windows 7.

  How access/start the process of recovery of the manufactures listed below.

  Acer: Press and hold ALT + F10, as soon as you see the logo
  http://Acer.custhelp.com/app/answers/detail/A_ID/2631 
  Acer support: http://www.acer.com/worldwide/support/
  Acer recovery support: http://store.acer.com/store/aceramer/en_US/eRecovery

  Advent: restart your computer, then the immediate start by pressing the [F8] key or the F10 key.
  The fastest way to restore your computer is to use the hard disk recovery tools. You can access them by restarting your computer and then pressing the [F8] key or the F10 key until the Advanced Boot Menu appears. Use the arrows to select "Repair your computer", then press [Enter]. Read all of the instructions on the website of advent and made your choice as to the action you want to perform: http://www.adventcomputers.co.uk/restore-or-reinstall-windows-your-computer
  Support: http://www.adventcomputers.co.uk/product-support/support-services

  ASUS: Press or press the F9 key as soon as you see the Asus logo.
  http://support.asus.com/Troubleshooting/detail.aspx? SLanguage = en & m = X53E & os = & no = 1775
  ASUS support: http://support.asus.com/contactus.aspx?SLanguage=en

  Dell: Press F8 directly after switching on / to start the computer
  Recovering detail instructions:
  http://www.Dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?docid=DSN_362066
  http://www.Dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?docid=52182
  Dell support: http://www.dell.com/support/home/us/en/19?c=&l=&s=
  Or: http://www.dell.com/

  EMachines: hold the Alt key and hold press and release the key F10
  http://Techchannel.RadioShack.com/eMachines-system-recovery-1747.html
  Support: http://www.emachines.com/ec/en/US/content/support

  Fujitsu: Press F8 several times directly after switching on
  https://answers.Yahoo.com/question/index?QID=20110406074143AAcx1Zw
  Support: http://www.fujitsu.com/global/support/

  Gateway:
  http://www.ehow.com/how_6297937_restore-gateway-laptop-factory-settings.html  
  https://support.gateway.com/s/software/Microsof/Vista/7515418/7515418su531.shtml
  Support: http://www.gateway.com/worldwide/support/

  HP Notebook: Usually to begin recovery process press the F10 key, power on the computer
  HP Mini: Press F11 directly after switching on / to start the computer
  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c01867418&cc=us&destPage=document&LC=en&tmp_docname=c01867418
  Support: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html

  Lenovo (F11): http://support.lenovo.com/en_US/detail.page?LegacyDocID=MIGR-4UFUYK
  and: http://support.lenovo.com/en_US/detail.page?DocID=HT077144
  Support: http://support.lenovo.com/en/supportphonelist

  How to run Lenovo Onekey Recovery
  http://support.Lenovo.com/en_US/downloads/detail.page?docid=HT062552
  Detailed as follows: http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=127597018499211

  You can also find parts of this article from Lenovo worth reading:
  http://support.Lenovo.com/en_US/detail.page?LegacyDocID=MIGR-4VFUDU

  LG: Press F11 directly after switching on / to start the computer
  Support: http://www.lg.com/

  Packard Bell: Turn on your computer. When Packard Bell logo is displayed, press in and hold the ALT key while pressing the F10 key several times. Release the keys when a message that Windows is loading files.
  After the system recovery program has loaded follow the instructions to reinstall the operating system.
  Support: http://www.packardbell.com/index.html

  Samsung: Press the F4 key to the Samsung logo when you turn on first of all of the computer.
  Support: http://www.samsung.com/

  Sony VAIO Windows 7: restart and press "F10".
  https://CA.en.KB.Sony.com/app/answers/detail/A_ID/35585/p/48903, 49902,71663,71664/c/65,67/kw/recovery%20using%20f10
  Sony VAIO Vista: Restart and press "F8" repeatedly until the screen "Advanced Boot Options".
  https://us.en.kb.sony.com/app/answers/detail/a_id/41931/~/how-to-perform-a-system-recovery-using-the-vaio-recovery-center.
  https://us.en.KB.Sony.com/app/answers/detail/A_ID/41949/session/L2F2LzEvdGltZS8xNDA4MjI2NTAzL3NpZC8qWVBPbCpfbA%3D%3D
  Support: http://www.sony.net/SonyInfo/Support/

  Toshiba: Press on F12 or the value 0 (zero) key on the top of the keyboard (not the zero on the numeric keypad key)
  and at the same time, press the button power once to turn on your laptop.
  When the Toshiba screen appears; release the 0 key.
  References: http://www.mytoshiba.com.au/support/items/faq/71
  http://forums.Toshiba.com/T5/system-recovery-and-recovery/how-to-perform-system-recovery-Windows-7/Ta-p/279643
  Support: http://www.toshiba.co.jp/worldwide/

  Windows 7 - location of the Partition Recovery and information.
  "Configurations of drive partitions using the BIOS has recommended.
  Note: Check the diagrams of this article
  http://TechNet.Microsoft.com/en-us/library/dd744364%28WS.10%29.aspx

  J W Stuart: http://www.pagestart.com

• IdeaPad y510p clean Windows 7 install - SSD not detected

  I bought a new Ideapad y510p just before Christmas and I wanted to do a clean install of Windows 7-64 bit.

  I created a USB startup device as required and put the drivers from lenovo on her page too.

  My problem is: after you delete the partitions, the installer of windows 7 do not recognize the SSD more...
  My BIOS is set with legacy of disabled secure boot support.

  Furthermore, when it came to load the drivers, it says no driver signed device not found.

  Someone has an idea of what's going on?

  Hi Clet,

  Since the serial number on this picture, you have the 59375625 model. After digging further, this parts search page and this point merchant does not seem an SSD on the specifications list. If the reception / box indicates that you have a 1 TB + 24 GB SSD, you may need to check under the hood (see pages 38-39 of the hardware maintenance manual)

  Link to photo

  Concerning

• V3 - 722G several BSOD after return to Acer repair

  Hello guys,.

  Short version:

  I'll be back just my laptop ACER repair center and I just did a complete reinstall of windows 8 with my USB stick recovery.  I spend about 15 to 30 seconds in the home screen accepting the agreement, computer name, etc., and the computer restarts with a BSOD.  I've seen 2 different BSOD so far:

  DRIVER_VERIFIER_DETECTED_VIOLATION

  UNEXPECTED_KERNEL_MODE_TRAP (nvlddmkm.sys)

  I really want to avoid sending this laptop to a 2nd repair, any ideas?

  Long version:

  I sent my laptop in for repair 2-3 weeks after the purchase when I noticed the 750 M from NVIDIA had stopped working a FAILURE of TDR video associate and I could no longer access NVIDIA settings.  The computer was essentially back to entirely using integrated graphics card intel (and it was very obvious of games with epic FPS loss). I've tried every driver wipes, reinstalls, different versions, spyware scans, analyses anti-virus, OS repairs, even tried wiping the computer clean with my recovery USB and reset the laptop back to finish on the default values of the box.  No luck, so I sent it to Acer repair center and they supposedly don't set.

  Well a month later, when I get it back, I turn it on and everything seems to work fine, so I'm going to update NVIDIA drivers to the latest version and Ottoman.  Computer BSOD over and over.  Tried to go back to older drivers and other versions with no luck.  I finally gave up and AGAIN completely erased and restarted my computer from scratch using my USB recovery.  But this time, I can't get past the screen of welcome/configuration windows 8 without it BSOD'ing with the above mentioned messages.  I tried to reset/wipe the computer AGAIN, I have tried refreshing, I tried running and disabling driver verification command line.  I tried to start windows with a low resolution.  I tried to boot into safe mode (cannot do installation in safe mode).  I tried to disable driver signature checking.  I tried over and over to auto repair.  I tried to isolate / removal / replacement of the RAM.  Heck, I even tried removing the WLAN card.  I'm out of ideas.  I was Googling for hours trying to find similar problems and have not met many solutions where people are stuck on the welcome/configuration with BSOD screen.

  The worst part is that I wrote on the box, I sent to the repair center I troubleshoot-performed and concluded that a video card failure or breakdown.  When they sent the laptop to me, the video card is not replaced.  In fact, no hardware has been replaced.  I would be not sent the laptop in a repair center after hours of troubleshooting if I didn't think it was a hardware problem.  The real diagnosis on my repair slip read: 'enabled Intel graphics.  All video past card tests. "Oh really?  Graphics card intel enabled?  I don't want graphic card intel, I want my paid for NVIDIA GRAPHICS!  You're killing me, Acer.

  This is my first purchase from Acer and I'm banging my head on the walls.  I'd like some suggestions.

  --------------------------------

  System:

  Aspire V3 - 722 G-9829

  All of the components that are currently in stock

  Hi simplifies

  I'm sorry to hear about the problems you've had, but I think that the only solution is to speak to press again for a 2nd repair.

• Clean Windows 7 install hangs during expanding windows files

  well, so that's what I've done so far, I have downloaded the kit of the student digital river, I originally ran Windows xp 32-bit, so when I ran first the exe download, it gave me the error of not being able to record in a single folder to read and what not, but I followed the suggestions on the forums to move forward a burn on a startup disk expandedsetup folder in converting it to an iso, which I did, I installed the first time but missed the option to format my hard drive so my old files were still there, however, once got installed win 7 I wasn't able to connect to internet for some strange reason and I couldn't understand it, so I decided to take the 3 files I downloaded originally from digital river and try their unpacking on the 64 bit OS now I had installed, it worked fine this time without any errors, so I moved the folder expandedsetup to my laptop and he burned them on a dvd as before, this time I boot from the dvd and do a clean install, it installs again very well, but once I login in the OS and I am getting started with things once again everything is grinding the long, I tried to restart and it does not work, this time it froze just a black before the paper screen, so once more, I started from the dvd and tried to do a clean install, but this time, he begins to hang during the part of expanding windows files, so I decide to make another disc using the second expandedsetup folder thinking that perhaps a new one was a bad burn, this does not work either, it takes about 14% of full on the extension of the windows files and then he told me that the files is not found, so I tried the second drive once again, we only got 4% until it gives me error on files is not found , so I put the first early in and try and suspension 4% right now and I expect to give me the same error, I have really no idea of happening, there are too many variables, but I tried to evaluate each of them, would be - this related material? my computer is compatible for win 7 64 bit, I ran the Upgrade Advisor before you buy, so I know that my hardware can run it, I think it's my dvd drive or the hard drive, but they both seem to run fine otherwise, any help would be appreciated

  Hello Impoc,

  Thanks for posting on the Community Forums of Microsoft Vista.

  Installation may stop if the system cannot copy files. Here are some possible causes and solutions for this problem:

  ·     Your Windows installation disc is scratched, smudged, or dirty. Clean the disc with a soft cloth, insert it in the CD or DVD drive, and then start the Windows installation again. If your installation disc is damaged, you may need to replace it. For more information, go to How to replace Microsoft software or hardware lost, broken or missing on the Microsoft Web site.

  ·     Your CD-ROM or DVD drive is not working properly or the disk might be vibrating too much for the laser correctly read data. For more information about this problem, see your hardware documentation or contact the manufacturer of the CD or DVD drive.

  ·     If your computer has multiple CD or DVD drives, your computer may attempt to locate files on the wrong drive. If your computer has a feature to disable CD or DVD drives that are not used, turn off readers that you don't use. Otherwise, try to insert the disc in a different drive, and then restart the installation.

  ·     There is a virus on your computer. Run an antivirus program to scan your system and to identify the necessary repairs. Don't forget to disable the antivirus before you start the installation again.

  Also, it is usually caused by hardware or software that is not compatible with Windows 7. If you have this problem, follow these steps:

  1. wait 10 minutes to see if the installation continues. Look at the led on the hard drive (often a small light on your computer that blinks when your hard drive is running) to see if there is no activity. If your hard drive seems to be working, the installation must be current. If your hard disk doesn't seem to work, go to step 2.

  2. If the installation fails again, it may be a hardware incompatibility problem. Go to the Windows Upgrade Advisor on the Microsoft website to see if your computer can run Windows 7.

  3. If you have compatible hardware and your computer still stops responding, disable any unnecessary hardware. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  If you have more than 1 Memory stick on your computer, try to remove all but one RAM stick and try to install Windows 7.

  If the computer still stops responding during installation, you may need to contact your computer manufacturer or retailer to check if the computer is compatible with Windows 7.

  Also check out the link below to learn more about solving Windows installation problems:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Windows-installation-problems

  Note: This article is related to Windows Vista. However, you can follow the same steps with Windows 7.

  If the installation fails after following the steps above, try to note the exact error message and provide the same.

  It will be useful.

  Thank you and best regards,

  Srinivas

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think