several IP - WRT54GL

Similar Questions

• Several DMZ on WRT54GL?

  Can I have multiple DMZ to open all the ports for my servers?

  My LAN configuration:

  Modem high speed > router > TWO workgroup switches > all computers

  I am using port range redirection (gives you only 10 places), and I am now using 7 of them. Xbox 360 only takes 3 spaces to open its ports required.

  I have a lot of servers and currently all the ports are open, but if I develop once again, I'm going to be hammered with no place to open the ports.

  My servers are configured manually the IP addresses: xxx.xxx.x.146 - 148.

  If there is an option to open a range of DMZ or forward all ports to a beach, that would be wonderful. Don't know if its possible, but if there is no DMZ options, could use the range of ports open and automatic reference all ports using that? as in the port from beginning to end strike on TCP and UDP port? EX: Port 20-80000, activate the TWO IP 146< not="" sure="" what="" the="" lowest="" port="" and="" highest="" ports="" are="">

  If its not clear enough, let me know and I'll try to clarify the best I can.

  Thanks in advance,

  DevilzEye

  www.tennisonet.com< tnt="" server="" website="" (so="" everyone="" can="" see="" what="" servers="" im="" running="" as="" proof="" i="" need="" these="" open="">

  Try third-party firmware on your router, as the tomato. It runs on your router, and I think you'll find some useful improvements on the stock linksys firmware. The limits on port forwarding have been considerably increased, and there are other options such as real-time and historic bandwidth control included...

• WRT54GL: Fast cable internet connection; very slow wireless

  I have been chasing a problem for months and I am at the end of my mind.

  I started with a cable modem Motorola SB5101 and Buffalo bison wrt-hp-g54.  For years, we had a (intermittent) desperately slow wireless connectivity.  Recently I started to run through Speakeasy.NET speed tests to try to find a motive.

  Wire speed is consistently running 15-16 Mbit/s, compatible with the speed promised our cable package.

  Wireless speeds were a different matter.  From multiple computers, they would sometimes as soon as the wire speed; then all of a sudden (from all wireless computers) the speed would fall to 0.5 Mbit/s or less, then the speed measured on our single wired computer remained at 15 Mbps.

  Restart the router would mitigate the problem for a while, and then the wireless would fall up to 0.5 Mbps.

  Wire speed would remain stable at the nominal 15 Mbit/s.

  Well, looked like a bad router.  I replaced it with a WRT54GL hardware version 1.1.  I've updated the firmware to the last - v4.30.16.

  I selected a channel (2) wireless network what inSSIDer 3 watch is not used by any neighboring router (i.e., no interference).  I have that checked regularly and am sure that interference is not the problem.  The router is configured for the wireless G only; WPA - AES.

  The same problem occurs with the new Linksys router.

  In desperation I replaced the old modem SB5101 with a new SB6141 cable, not believing there could be everything possible that could help but, this what the devil - we will eliminate it as a factor as possible and go to DOCSIS 2.0 to DOCSIS 3.0.

  The problem persists.

  Thus, new router, cable modem brand new, constant wire-speed, without strong signals wireless, channel interference all around. but the problem persists. There has been no improvement on the old hardware I used.

  All computers, but a (XP Pro) is running Windows 7 Pro.

  The problem is not predictable, except that the speed degradation will happen sooner or later - and this is not progressive.  Suddenly, he fell like a stone and sticks to 0.4 to 0.5 Mbits/sec.  Reboot the router (usually) will fix it for a while, and sometimes it will clear up on its own, given enough time.

  I ran inSSIDer several times while this is happening, but he sees no other no signal on the channel I use--in fact, none on adjacent channels either.

  I checked from wireless to the router table and there is no other than our device, so it does not appear that the network has been hacked.

  Does anyone have an idea what might be going on or suggest an action plan?

  The only thing I can think is that there is something between the router and the computers wireless in the House which is eating up 95% of the bandwidth wireless - a sort of voting out of control.  But what?  I'm completely stuck.

  Follow-up.  I changed the channel 1 wireless; After doing some research I realized that sharing a channel (as long as your signal is at least 20 dB louder) causes fewer conflicts overlapping channels.  I have not changed anything else.  I'm tempted to allow the break-up of the frame but implementation of that seems to be somewhat specific to the supplier so I'll let it be.  In any event the wireless speed now as fast as the wire speed.

  The result is that since the re - install the Linksys firmware and do a hard reset that I saw not a single instance of the speed problem.  So I still don't know exactly what caused in the first place, but I'm glad that the problem has disappeared, so I'll just let things be.

  Thank you!

• Much faster WRT54GL (5.4mpbs down) wired then on wireless (1.2mbps down)

  Hello

  I have speed issues on the side of my WRT54GL Wireless Router v1.1.

  When I plug in a laptop to the wired port, I get about 5.4mps down when wired, but only 1.2mpbs down the wireless.

  I'm tempted to do a factory restore. I made sure no quality of service is in place. I tried several devices to make sure that this is not something on the side of the device causing this problem, but all devices perform just as badly the wireless but also on cable.

  Do you have any suggestions on how I could fix this?

  Change channel wireless 1, 6 or 9. Make sure that wireless security is set to WPA Personal.

• WRT54GL cannot transmit from inside the LAN port?

  Hello

  I have a Server servers running several (HTTP, SVN, FTP,...) inside my network.

  I used to have a SMC router in the past, and of course I had to use port forwarding.

  This is why I realized that when we "talk" to the server, I can 'talk' to the router that will forward requests to the right compurer, based on the NAT table. If, for example, that if I move the SVN server, I don't have to change the path to the repository, change the NAT entry is OK in this case.

  If this is not understandable, here 's another report.

  However, I discovered that even if my new WRT54GL seems to be much more advanced, it cannot do this. Requests made to the router from within the local network are not transferred to the right place.

  Is there a way to accomplish what we need, or at least a road map? It's sad that the SMC products otherwise is not very reliable can do...

  Kind regards

  Matej

  Well, I have it solved.

  I tried to convey the SVN, HTTP, FTP, and SSH.

  However, it was not working when the server IP assigned by DHCP.

  When I set up (the server within the LAN) to use the static IP address, not only that port forwarding began to make sense, but I have seen web pages by typing my public IP address in the browser on a computer inside the LAN.

  What surprised me, is that it only worked when the server had assigned auto private IP address. I know that these addresses change so it would not very long work, but it did not work even before that t has changed...

• WRT54GL and Windows 7 log in question

  I have a network of several PC on my WRT54GL router - firmware 4.30.14 building 5, October 26, 2009

  All PC's are XP SP3 except a Win 7 PC

  When I access my WRT54GL from all of my XP computers, I connect at once and I'm done. I can access all the pages then configuration.

  When I connect with my Win 7 computer, I get the security pop Windows window whenever I click on a page or a new tab.
  I can see all of the pages and tabs without problem once I get the password again, but it's really annoying that he keeps asking

  for the log information for each new item, I click on.

  Checking her memorize my box of credentials is not good, it always ask again and again

  This is my first Windows 7 computer, not sure how to stop this behavior annoying.

  Any help on this is appreciated

  This is the window that will open all the time

  

  Update

  This seems to be a question of IE9

  I saw just the router with Firefox and Windows 7

  He only asked for username and password once and I was able to browse all the pages without further asked for info, log in.

  I'll go ahead and mark it as a solution because it seems a problem of IE9

• WRT54GL wired connection drops

  I've got a WRT54GL Wireless G from Linksys. I do not currently use wireless. (I've disabled.) It worked fine when I got it, but now removes several times a day. The frequency of drops has increased during the last two weeks. A manual reboot of the WRT54GL resets the connection. (The connection is lost too whenever the computer is restarted and it also forces me to restart the WRT54GL)

  To initially get a connection, I had to follow the routers cascading tutorial that requires the internet to be put at the first port and way wired for access from the second computer. (Because I'm using a combination modem/router device, connect the cable to the modem/router directly on the internet/ADSL port on the WRT54GL did not.)

  I tried to access Google directly by IP (74.125.159.106) and this does not work, even if I can't actually search. (I deleted the browser cache before checking this.) The lights on the modem/router and the WRT54GL are turned on, then the two seem to work fine. I can also access the web interface for the WRT54GL. (I don't think I can access the web interface of the router/modem, but I need to confirm that the next time the connection drops).

  For this reason, I don't know if it's really drop the connection, or if I'm just unable to what location. What I read, it can be linked to a dns issue, but I don't know much about these things.

  Thanks for any help

  Maybe you've found the 192.168.1.x ip address between your modem and that's why you get no internet when you connect the modem to the router on the internet port.

  Your router does not work as a router here... You connect the modem to the router to the Ethernet port, it works as a switch...

  I would suggest that allowing you to convert the modem in Bridge mode and then connect the modem to the router on the internet and computer port to the router to the ethernet port... Now open the linksys configuration page by typing 192.168.1.1 in the address bar and configure the router with PPPoE settings.

  The second is option... Connect the modem to the router on the internet and computer port to the router to the ethernet port... Now open the linksys configuration page by typing 192.168.1.1 in the address bar. Now, change the ip address of the router linksys 192.168.2.1 and save settings... Network power cycle and it should.

  Check out this link.

  If you have found the intermittent connection to the router then, reduce the MTU to 1350 and cycle power to the router.

• How can I change several download Sierra systems

  How can I change several download Sierra systems?  I have a Mac mini end of 2012 running El Capitan, over a mid-2010 Mac mini and MacBook Pro mid-2010 the two race Yosemite with limit of bandwidth on my internet connection and want to update all three systems in one download.  Is the process that apply with Yosemite and El Capitan (ie. Copy the Setup program to another location before you run it on the download system) still the way forward?  Thank you.

  You can do this or DiskMaker X allows to create a key to install it.

  (145170)

• I have several new emails in the Inbox, but I'm unable to view or even see them?

  I have several new emails in the Inbox, but I'm unable to view or even see them?

  Hey CRB123,

  Thank you for being a part of the communities of Apple Support.

  If I understand your message, you see a badge that you have unread e-mails in your Inbox, but they are not appearing.  An easy way to separate the emails read from the unread macOS that Sierra is to click the button to filter in the list of messages, or sort by unread:
  

  • Activate the filters: Click the filter button at the top of the list of messages, click unread to display the list of available filters, and then select one or more filters. A check mark indicates a filter is active.

    

    If you use more than one email account in Mail, you can filter the Inbox into account - for example, only show emails from your iCloud account.

  • Disable an active filter: Click on the filter.

  • Disable all filters: Click the filter button .

    Mail remembers your filters and automatically applied the next time that you click the filter button to activate the filters.

  You can also sort the list of messages - just click on "sort by" at the top of the list of messages, then select an attribute, such as and a sort order. In a typical configuration, click on a column header.

  Mail for Mac: filter the list of messages in Mail

  If no unread messages, then I would like to confirm if you have emails unread looking webmail for your email account. If you see the unread messages in webmail, go back to the mail app, and then rebuild your Inbox:
  

  You may have to re-create a mailbox to update the list of the messages it contains. For example, if messages seem to be missing or garbled, or if you don't find any relevant messages when you search by using the entire Message search option.

  • Select a mailbox in the Mail sidebar, then choose BALL > rebuild.

  When you rebuild the mailbox for accountIMAP or Exchange messages and attachments stored on your computer are discarded and then downloaded again from the mail server to your Mac. Your mailbox is empty until the download is complete.

  Mail for Mac: rebuild the mailboxes

  Take care.

• Synchronization of photos for the records of several PC iPAD

  Hello

  I have pictures in several files in my PC.

  I would like to synchronize all at once to my iPAD.

  When I opened "Synchronize the Photos" - page in iTunes, it is possible to select only a single folder.

  Is it possible to select several folders?

  Peter

  If the records are directly under the same parent folder then you should be able to select this parent folder at the top of this screen of Photos and records of the child must be indicated below (if you select "Selected folders") for the selection and timing of the iPad for example

  

  If files are located on your computer, then no, you will not be able to select and synchronize them with your iPad - I created a folder separated (with specific subfolders for holidays/events) for the photos that I have synced my iPad

• Table of contents for several sheet file...?

  It is possible to:

  1. Create a Table of contents listing all sheets in a file?
  2. Have these hyperlink worksheet titles to the sheets themselves?

  I build what will eventually be a fairly large file (read: 75 + leaves). Rather than scrolling all the leaves one by one by one manually to locate the correct table, it would be useful to have a table of contents or an Index that lists the in order... Ideally, allowing the connection of hypertext link to the leaves they reference. (I swear that this was part of a way-back-when number...)

  Instead, is it possible to auto-trier worksheets in alphabetical order? He would not give me the project view as a table of contents or an Index of 35,000 feet, but at least it would be a little easier to find what it takes.

  Looking forward to sharing the wisdom...

  HI stephanie,.

  The numbers 2 (' 09) and 3 support not the hyperlinks to locations within the current document. Both take in charge of hyperlinks that open a Web page in your default browser or which will open and send a new e-mail message.

  Command-F can be your friend here.

  Place an array of single cell on each sheet (or use a cell on the existing table). Enter a short text string that identifies the table or sheet. Each string must be unique in the document.

  To access the card containing one of the following strings:

  Press Control + F to open the Find dialog.

  Enough chain to identify the worksheet type.

  Number will draw this roadmap forward as soon as it can determine which table contains the cell containing this string.

  Tested with four sheets containing:

  able, baker, charlie and delta

  With this limit together (and any other tables in the document - quite an artificial situation!), type c or d was enough to bring me to sheet 3 or 4, sheets 1 and 2 required two letters (ab or ba) to identify the good sheet and bring it forward.

  

  

  With a document containing several tables (and more leaves), create (and remembering) a separate channel for each becomes more complicated.

  You can place a second copy of each in a table of Index or table of contents on a separate sheet. From the index table,

  Copy the entry for the table/worksheet you want to go.

  Open the dialog to find (command-V)

  Paste the entry in the search box. (What it will find and highlight the entry that you have copied to the index table)

  Click on the > button on the dialog to find the occurrence FOLLOWING this string (on your target table.

  Kind regards

  Barry

• Scan with preview - several Pages of a PDF THAT does not work in Mac OS Sierra

  Hello everyone,

  I had upgraded my Macbook Pro (early 2011) to Mac OS Sierra. A famous feature of older versions of Mac OS is to use Preview to scan documents to PDF format, joined the pages scanned all of a single document.

  After upgrading to Sierra this feature does not work correctly. The pages are not more combined into a single PDF. Anyone who has observed the same problem?

  Best regards from the Germany

  Jörg

  Yes, it's been posted here several times.

• I followed these steps several times, but he still has to work to rebuild the index.  Is there something else in the way of this work?

  Have you tried to rebuild the index spotlight several times, but it didn't work. I followed the steps through the system preferences, but there is no result for the rebuilding of the index.  Is there another way to do it, or is there another problem preventing it from working?

  Do you mean the following steps:

  Rebuild the index on your Mac - Apple Support Spotlight

• my itunes asked several cd's save a playlist of 55 minutes on a cd of capacity of 80 minutes.  It was working fine and it started a few days ago.

  MY ITunes started to ASK WHAT SEVERAL CD's save a PLAYLIST of 55 MINUTES ON ONE CD CAPACITY 80 MINIUTE.  IT WORKED VERY WELL AND STARTED TO DO THIS WITHOUT ANY CHANGE OF CONTROL.

  Sorry, but your question has nothing to do with Apple networks. You can have the best results to get a possible solution if you send your message to the communities to Support Apple (ASC) region of iTunes .

• Choose several folders with choosing menu and empty their contents

  Hi all

  new to applescript and want to create a file menu choose where I can choose several folders and empty their content. There will be a dialog box at the end let me know that the files have been purged. The script I'm working for an individual file:

  say application 'Finder '.

  Close each window of

  Open (choose folder with prompt "including one or more folders should purge?" multiple selections allowed location 'True' by default ' / users/bryceratops / ')

  Set an to front Finder window

  move each agenda a in the trash

  Close front The Finder window

  end say

  say application 'Finder '.

  display the dialog box buttons "purged records." {"ok"}

  end say

  
  

  But Im having this script to open, purge and close every finder window, if I selected several files in the menu choose a wire installation difficult.

  
  

  Any ideas?

  
  

  See you soon
  

  Hello

  Put the output of the command 'choose folder' in a variable (no need to open these folders).

  ----

  the tFolders value (choose a folder with default location "including one or more folders should purge?" guest "/ users/bryceratops / ' with multiple selections allowed)

  Tell application "Finder".

  Repeat with thisDir in tFolders

  remove items from thisDir - trash

  end repeat

  tell the end

  activate

  display the dialog buttons "purged records." {"ok"}

  ---