Several simple syslog server session PIX

Similar Questions

• Enable syslog server behind the PIX

  Could someone tell me a config that allows a server syslog (Kiwi syslog) to get behind the PIX syslogs. I have a 2K with the KIWI syslog server behind a PIX 501.

  I have the static command, the access group and the access-list:

  public static 192.104.109.92 (Interior, exterior) 192.168.15.200 netmask 255.255.255.255 0 0

  Access-group local_server in external interface

  local_server list access permit udp any host 192.104.109.92 eq syslog

  Man, I can't understand it.

  Thanks for any help

  You could:

  1. make a capture of port syslog traffic directed to the syslog server.

  2 Terminal monitor - deny traffic showed clearly when I had not set up the firewall to forward the traffic. (Note: attention on busy firewall)

  3 netstat - a on the syslog server

  4. If you allow, you should be able to portscan the server on port of syslog by your firewall.

  5. is your syslog capture created file? It is not created if the service never started.

  6 - is the service running in the system context or perhaps another account that doesn't have the correct rights?

  The answers seem to indicate a service not started that seemed likely. What you describe happened to me when I had the demon also version; I went to service version and the problem has been resolved (once I opened the port.)

  I love the kiwi syslog. I use with Snare and BacklogIIS and receive alerts within 60 seconds to my mailbox when something bad happens. It always fools of my end users out when I call them with the problem solved when they seek always my number report the problem.

• Accounting ACS logs to Syslog server

  Dear Experts,

  We use the Cisco Secure ACS 4.2 in our Organization, where accounting Ganymede has been turned on AAA cleints. Currently, ACS connects with the accounting information accurate cli.

  Is it possible to repel these accounting logs to syslog server. For example, here's a scenario.

  User connected to the Cisco device at 10:00 and configured the device with 5 orders and logg unit at 10:05. These must be alerted/connected to the ACS syslog server.

  Kindly advice...

  Best regards

  Shiji

  Shiji,

  Yes you can.

  Go to system-> logging configuratoin and page you can configure which opens a session must be sent to the syslog server.

  

  HTH

  Amjad

  Rating of useful answers is more useful to say "thank you".

• VSphere ESXi 5 - point syslogging to Kiwi SysLog Server 9.2

  We have several server ESXi 4.1 pointing to a Kiwi Syslog server v9.2.

  All point their 5 Kiwi Syslog server ESXi vSphere servers? Any help on this is appreciated.

  Can't seem to point ESXi correctly because the settings all look different.

  Thank you

  Changing the syslog settings don't automatically open Firewall ports.  You will need to go to the screen of the security profile to do so.

• Build / / need a syslog server

  Anyone using a syslog server to capture Standalone ESXi host newspapers? I have a cuople stand-alone ESXi 4.x hosts and must start collecting newspapers because we went haywire on me this weekend.

  So my question is, what products do you use for syslogging? A free one is better but not necessary.

  It is true that I have never created a simpler product, as for "Dummies", would be so probably ideal.

  Thank you

  Kiwi is a great service, it is highly recommended and now is strongly recommended

• Whenever I connect to a remote connection, I get an error message "unable to connect to this Terminal Server session remote control"

  Original title: unable to connect to this Terminal Server session remote control?

  Whenever I work with my friendly by connecting remotely, this information is pop ups as follows:

  Remote control cannot connect to this Terminal Server session. It is a known problem with Windows 2000 and XP and can occur under certain, rare conditions. To remady this situation, ask the local user switch to another session (connecting, on or off), or restart the computer.
  I know it's something related to windows authentication. But want to know in detail about this notification.
   

  Hi Victor,

  The question you posted would be better suited in the TechnNet Forums.

  I would recommend posting your thread in the link below:

  (Services Terminal Server) remote desktop services:

  http://social.technet.Microsoft.com/forums/en-us/winserverTS/threads

• Equalogic: grpparams syslog-server-list agreeing not to port

  I am trying to add a target server syslog with a custom port. It does not accept the port via the GUI or the CLI.

  I type grpparams syslog-server-list x.x.x.x:yyy

  It is said "% error: invalid IP address '.

  the GUI and CLI accept IP with no port.

  Is this a bug?

  Thank you

  James

  Hello

  Sounds like the bug in the documentation.

  It has been a feature requested for some time

  Don

• Syslog server Red Hat

  My station have dual boot, Red Hat 8.0 and Windows2K.

  How can I configure my Redhat 8.0 syslog server to receive my routers ACL logs?

  When I use a syslog with Windows2K server software Kiwi, my machine to receive the newspaper ok.

  Thks,

  Paulo

  I'm no expert, RedHat, but if it works the same as the Unix standard (that I tink, it does), you must change your file/etc/syslog.conf and direct specific syslog events in a specific file.

  Syslog events from a default router are sent using the local7 facility, so if you do something like:

  ADM local7.*

  (Note there is a TAB between the installation type and directory in this file) then your syslogs must be logged to this file. You need to stop/start the syslog server on the machine after making the change.

• Write syslog to ASA 5505 VPN tunnel on syslog server?

  Hello

  Is it possible to let the ASA 5505 write syslog messages to a syslog server on the core network where the ASA 5550 is? (on the ipsec tunnel?)

  I tried this. The tunnel is up, but I get the message from routing could not locate the next hop for the NP (ASA 5505 ip) udp inside: (ip of the syslog server).

  THX,

  Marc

  MJonkers,

  I would suggest that you configure inside interface as the interface for management access. Include IP and IP address NAT syslog server interface inside 0 ACL and ACL crypto.

  You can order the "access management" when you want to run an ASA inside of interface through the VPN 7.2 below command reference:

  http://www.Cisco.com/en/us/customer/docs/security/ASA/asa72/command/reference/m_72.html#wp1780826

  I am running the VPN configuration on 8.2 and querying SNMP works.

  I hope this helps.

  Thank you

• Sending events in connection to Syslog server

  Hello world

  Need to know in the centre of defence we can send all records messages in syslog server just as we do for any cisco device.

  Is it possible that we can also send connection events and also Intrusion to the Syslog server?

  Is this possible?

  Also where in the centre of defence do us the syslog server configuration?

  Concerning

  Mahesh

  Mahesh,

  Please see the User Guide for the system FireSIGHT, Chapter 44. It includes a section on "Configure Syslog Responses".

  Here is a screenshot where you set up on the events of the Intrusion:

  fmc_syslog_setup.PNG

  

• How to send IPS events to a Remote Syslog server

  Can someone point me to a doc tech "how to send IPS (v7.x) events to a Remote Syslog server.

  Pls kindly marks the message as answered. Thank you.

• Cisco ISE and external syslog server

  Hi Security Experts,

  We start with deployment cisco ISE (Identity Services Engine) in our network. We have allocated 250 GB of space for the node (Admin + monitor) ISE.

  I want to know if we can send tracking of nodes of external syslog server logs after a defined time interval.

  For example, newspapers that are more than 10 days are for external syslog server. So basically our node monitoring will have the marbles which are the Max 9 days. Is this possible? Could you tell me some doc that explains the configuration of the same thing?

  Thank you

  Boudou

  No this is not possible via syslog. What you need is database purge, so that the monitoring database is purged after a determined time interval. Here's a guide that will help shed some light on this:

  http://www.Cisco.com/en/us/docs/security/ISE/1.1/user_guide/ise_mnt.html#wp1054328

  Tarik Admani
  * Please note the useful messages *.

• DHCP server for pix

  Server DHCP - pix - dhcp clients

  is it possible to have a dhcp server machine to say the inside interface, and dhcp clients are on the dmz?

  Thank you

  a feature named dhcprelay should solve your problem. I did the opposite, i.e. the server dhcp on the outside and the customer inside. However, I guess that the 'dhcprelay' command should do.

  for example

  dhcprelay Server 192.168.2.2 inside

  dhcprelay enable dmz

• TMS & syslog server

  Hello

  I want that my TMS pointing to the syslog server server, how to proceed?

  I just checked the MSDS and even our TMS admin guides.  None of them mentions the possibility of using a syslog server, so it seems that this is not possible, unless there is another way to do that is not documented or within the TMS web interface.

  If it's something you'd like to really see included, suggest you to contact your Cisco account manager and file a feature request.

• Why should I sign if often, sometimes I have to sign several times during a session.

  Why have I not connect so often? Sometimes, I have to sign several times during a session.

  This might help:

  https://helpx.Adobe.com/creative-cloud/KB/signed-out-sign-in-required-error-248.html