SG300 10 p - disconnects after trying to apply the ip to the VLAN

Similar Questions

• When I try to start the computer in the morning, he goes off and after trying to restart the computer 2 times it becomes normal. Please give me any solution for this.

  When I try to start the computer in the morning, he goes off and after trying to restart the computer 2 times it becomes normal. Please give me any solution for this.

  Hey Abdul HamidNagoor,

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  ·         What is the brand and model of the computer?

  Follow the steps in the article.

  Advanced Troubleshooting for General startup problems in Windows XP

  If the problem persists, follow the steps in the article.

  How do I recover from a corrupted registry that prevents Windows XP startup

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://support.Microsoft.com/kb/322756

• After trying to install the updates. my computer is now stuck in constant reboot mode while showing "Configuring updates 3 of 3 0%, do not turn off your computer.

  Visa update problem

  After trying to install the updates.  my computer is now stuck in constant reboot mode while showing "Configuring updates 3 of 3 0%, do not turn off your computer.  I tried to follow the instructions provided here because it seemed to be the same problem.  But when I restart and hold down the F8 key so I can boot into safe mode, I tried selecting safe mode and I get the same results, and I tried again by selecting the option 'Disable automatic reboot' which seems to be an option on the same page with the option of safe mode.  Whatever it is, the same message comes back and I can never get to where I can see my desktop to click 'start '.  I can't get out of this cycle.  I installed the update because it said I needed to install it.

  *************************************************************************************************************************************************

  Turn off your computer by holding the power button for about 20 seconds.
   
  Start your computer in safe mode: press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears
   
  Disable the automatic restart in the event of system failure:
   
  • Click Start
  • Click on Control Panel
  • Click on system and Maintenance link.
  • Click on the system link
  • In the left pane, click Advanced system settings
  • Locate the startup and recovery area, click the settings button.
  • In the startup and recovery window, uncheck the box next to automatically restart.
  • Click OK in the startup and recovery window
  • Click OK in the System Properties window
  • Close the system window
   
  After that... While STAYING in safe mode I do a system restore and maybe try a manual install of the update later.
   
  For the sake of space I refer you to the article about how to proceed.
   
  System restore
  http://windowshelp.Microsoft.com/Windows/en-us/help/9f6d755a-74bb-4A7D-A625-d762dd8e79e51033.mspx
   
  Windows updates: http://windowshelp.microsoft.com/Windows/en-US/Help/8f259118-0d61-4c7a-8c56-24987e87a8171033.mspx
   
  Please let us know if this solution works for you

  Theresa
  Microsoft Answers Support Engineer

  Hello

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Hi, I just bought Adobe Acrobat Pro DC. I used the link that was sent to me to download. But the download was not successful. After trying 5 times, the system says, now I downloaded too many times and has refused to let me download it again. It's someone

  Hi, I just bought Adobe Acrobat Pro DC. I used the link that was sent to me to download. But the download was not successful. After trying 5 times, the system says, now I downloaded too many times and has refused to let me download it again. Someone from Adobe is reading this? How can I get this fixed a problem? Thank you.

  Download Acrobat products | Standard, Pro | DC, XI, X

• No image color after you have applied the effect "graphic pen.

  I opened a .dng file which was in black and white. Then he converted to RGB. Apply the graphic pen effect. Add a new layer, fill it red, changed the mode of Overylay, and when I tried to merge down or save it in jpeg format, it converts the right on the image back to B & W, I even tried to change my red brush and overlay mode, it just won't let me the image of color at all. I tried to hue/saturation, and when I try to save the setting, it converts right back to B & W. Any help? Here are a few screenshots.

  

  It's after the merger down.

  

  The overlay mode don't effect pure black and white pixels.

  Try to view your image at 100% view (actual pixels) (double click on the Zoom tool in the Toolbox)

  Views others 100% cannot give you a vision accurate of your image especially when it comes to blending modes how to interact between the layers.

  I would suggest using a solid color fill layer and raise the blending Options dialog box, where you can scroll through the different blend modes

  to see the effect on your image, your image is 100% view (actual pixels)

  

• After trying everything on the page crashsolver, 41.0 Firefox still crashes in some places. What can be the problem?

  My browser crashes even in sites, such as Google Maps, or site to ask support from Mozilla. It stil happens after I tried everything on the Mozilla troubleshooting page, but in safe mode, it is not present. This happens after reinstalling Windows 7 on my computer. What can be the problem?

  Problem solved (apparently...). As you say, the problem was with the graphics driver. I completely uninstalled the driver and all its folders and files (with the help of a program) and re-installed. Accidents to certain pages from before are gone. So thank you for the help.

• Request for BIOS password after trying to wipe the hard drive?

  Hi - I got a new computer and tried to erase the hard drive on my old Toshiba laptop for sale on. It is a Toshiba A-210 and is about three years old.

  I put the "settings factory restore disk" and tried to follow the instructions on the CD cover. However, the instructions don't match the options given, I did something where I thought I was wiping the HARD drive. It seemed to go ok, but when I tried to start it again, it loads a black screen type "MS-DOS" asking for a password.

  The password only I put up on the computer was for my user profile, and it's not accept that. If I try to go on without the password, the computer turns off.

  I tried Googling and it could be a BIOS password, I think, but I've never been one of these. The only suggestions I could find for fixing involved by pressing one of the buttons "F" and move to Windows, but I can't get an answer using the 'F' keys On the Toshiba site it said that I needed to have it fixed by one of their authorized places, but I don't want to spend money on it, because I was trying only to erase the hard drive before trying to sell it on or scrapping it.

  Does anyone have any suggestions? My hard drive was erased? There is nothing really confidential there, but I like it as clear as possible, I really don't mind if its working, I would consider it breaks to pieces.

  Post edited by: katy_c

  Hello Katy

  After reading your thread I don't understand what you've done to lock your computer.
  Still is it BIOS password cannot be set by mistake.

  When the BIOS password to settle should be written twice before, it will be activated.

  What to do now? Is that the BIOS password can be deleted by a combination of keys or something simple. BIOS password is the most important safety feature and must offer the maximum protection of the BIOS.
  You can sell your laptop without HARD drive too. On eBay, I saw many laptops that will be offered without HARD drive for data protection reasons. HARD drive can be exchanged for less money and it is not so important hardware component.

  In the history I see a problem only: BIOS password. You can offer a little cheaper laptop and the new owner can pay for password removal.

  It is not easy to give you the right answer. I just want to be a little more realistic.

• Cannot start Windows after trying to install the Vista SP2

  I just tried to install Vista SP2 and now whenever I try to turn on the cpu it gives me a blue screen and restarts. It does allow me to start in SafeMode either. In addition, it seems to be impossible to find my restore points. I was able to stop the screen using the F8 menu and it gives me this error on the blue screen

  STOP: 0X0000007E (0XC0000005, 0X81C223BB, 0X803998F4, 0X803995F0)

  For some reason, when I go to the cmd prompt to advanced troubleshooting guide, I can do, he says that I am the X and not the C drive, if that has something to do with my restore points does not.

  I tried to get the menu of the restoration on C manually through C:\windows\system32\restore\, but nothing was there.

  Any help would be appreciated. I will not lose rather all my data in a reformat.

  Thank you
  Matt

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?  Who were these applications that run in the background when you installed SP2?

  A (another) Norton or McAfee application has already been installed on this machine (for example, a free trial version which is preinstalled when you bought it)?

  
  0X0000007E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED
  A system thread threw an exception who did not catch the error handler. There are several individual causes for this problem, including the hardware incompatibility, service driver or defective peripheral system or software problems. Check (EventVwr.msc) event viewer for more information.
  
  Source: http://aumha.org/a/stop.php#0x7e

  
  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:
  
  0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred. [emphasis]
  
  Source & more: http://msdn.microsoft.com/en-gb/library/ms795746.aspx

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been extended until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; ( Problems after installing a service pack).

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• System error / stop when trying to apply the animation to text on securities.  Already uninstalled and reinstalled. same mistake.

  Hello

  I just downloaded items from adobe first.  I'm unable to apply any transition to my title text.  The system gives the error:

  [/ Adobe/pre/main/libraries/HSL/Make/Mac /... /.. / Src/Views/MediaListView.cpp-3820]

  And then prior to the decision.

  I tried to uninstall the software completely and reinstall with no luck.  I use a new iMac so I doubt its my computer.

  Thank you

  rachelstrachel

  1. I'm strictly a Windows elements users, and it is my second hand information on when the Adobe Premiere elements Prefs file is Mac.

  I want you will find this file and delete it. I think this way seems it

  Users\Owner\Libraries\Application Support\Adobe\Premiere Elements\13.0.

  2 start a new project. Create your title in the Titler as follows.

  a. text Menu/new text/text default

  b. type your text in the text Section of the module of titration. Select the tool selection at the bottom of this article and then click on the text

  on the screen to select and get a bounding box around the text.

  c. go to the Animation Section of the module of titration. Click and drag the text Animation named bland by the line of the display of animation of the neighborhood of choice

  in the text on the screen or select Fade In by Line, scroll down the text animations, and click on apply.

  d. close the titration module.

  e. return the content of the timeline by pressing the button made above the timeline and you see the result of text animation.

  How long in the process do you have? Same problem as reported? Or this time it worked?

  RTA

• Error message after trying to download the new update of photoshop

  I tried to download the new update for photoshop cs6 several times... after downloanding and installing, I get an error U44M1P7 at the end of each attempt... It seems to be very well until after the download is complete... I tried to reload the photoshop and there will be mistakes off of suggestions? It's about new features... Thank you... Terry

  Run the Creative Suite cleanup tool, reinstall PS, try again...

  Mylenium

• print spooler off after trying to print the declaration of Canadian Tire online

  I tried to reinstall the drivers, but the computer does not recognize that the printer was even plugged and it was.

  The last time this happed I ran a system restore and print to function.  This time system restore will not work.

  Hello

  ·         What version of the operating system is installed on the computer?

  If you use Windows 7, and then run the printer troubleshooter.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  See also: http://windows.microsoft.com/en-US/windows7/Why-cant-I-print

• Cannot access the network drive after trying to change the shared folder.

  I had a 80 GB drive connected to my E3000 for a few years and it worked without problem. I recently turned to a 250 GB Maxtor One Touch drive. When I plugged it, the router automatically creates a shared folder. I was able to connect to this folder without problem, but I wanted to share the whole score. When I made this adjustment and tried to save the settings, I temporarily lost access to the router. He gave me the standard page cannot be error message appears. When I got access changes seem to be made. When I try to access the drive of my laptop I get this error message, "the mapped network drive could be created", "the name specified network is no longer available". I rebooted and power rolled my router as well reconnected the drive.

  I think that since you have replaced your hard drive, old settings are configured may still on the hard drive of old. You can change the users and group so that it syncs with the new hard drive or start from scratch (reformat the hard drive).

• "VMware ESX Server doesn't have storage persistent." after you have applied the latest updates.

  This weekend, I applied the updates on a server ESXi 3.5 Update 3.  The update process indicates that a restart is required, so I stopped all the guests and then restarted the server ESXi Infrastructure customer.  To reconnect to the server, it has more a defined data store.  The 3i command prompt, I see yet that/dev/discs / vmhba1:0:0:3 the size of my previous data store.  Someone there can help me with what has happened in my store data and, more important still it, can I get it back?

  Thank you.

  If you go to the console, you will see the disc if you run fdisk-l?  If so, go to Configuration-storage adapters and click on the link of the new analysis.    If that don't is not raise the datastore glanced at the logs and see if there are errors on a snapshot and then take a look at the advanced option LVM. EnableResignature - (page 118 ff) http://www.vmware.com/pdf/vi3_35/esx_3/r35/vi3_35_25_san_cfg.pdf.

• Cannot start windows after trying to resize the partition.

  I tried to use utility disk to increase the size of my windows partition, of course, broke TI boot camp should have read this on the community before the trial.

  I use all the solitaire t controls, including the following

  Fdisk e/dev/disk0

  p

  setpid 4

  07

  Pavilion 4

  p

  To write

  There

  That did not help, I don't see windows when I hold down the option key. The windows partition exist again, however, which is good. Also, I turn off csrutil, I use the latest version of Mac OS X

  diskutil list

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 251,0 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS Macintosh HD 165,1 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 85.0 GB disk0s4

  Cs diskutil list

  No logical volume group CoreStorage found

  sudo TPG - vv - r see the/dev/disk0

  Password:

  See the TPG: / dev/disk0: mediasize = 251000193024; SectorSize = 512; blocks = 490234752

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  See the TPG: / dev/disk0: Pri GPT to sector 1

  See the TPG: / dev/disk0: GPT Sec at sector 490234751

  start index size summary

  0 1 MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 322541752 2 part TPG - 48465300-0000-11AA-AA11-00306543ECAC

  322951392 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  324220928 166012928 4 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  490233856 863

  490234719 32 table dry GPT

  490234751 1 dry GPT header

  Udo fdisk/dev/disk0

  Disk: geometry / dev/disk0: 30515/255/63 [490234752 sectors]

  Signature: 0xAA55

  From end

  #: cyl hd s - cyl hd s id [Start - size]

  ------------------------------------------------------------------------

  1: EA 0 0 2 - 25 127 14 [1-409639] < unknown ID >

  2: AF 25 127 15 - 1023 254 63 [409640-322541752] HFS +.

  3: AB 1023 254 63 - 1023 254 63 Boot Darwin [322951392-1269536]

  * 04:07 1023 254 63-1023 254 63 [324220928-166012928] HPFS/QNX / TO THE

  Help, please.

  Please after the release of

  sudo dd if = / dev/rdisk0s4 account = 1 2 >/dev/null | hexdump - C

  Since there is no extra partition now, did you remove using disk utility?

• Satellite P200-1 has 2 dead after trying to update the Bios

  Hello

  I downloaded the latest version of the BIOS firmware of Toshibas site (European site). I checked it clearly with the model nr and serial nr. I went on the northern site to update bios and downloaded the latest drivers and BIOS.

  My laptop Satellite P200-1 has 2 and the nr series is PSPB6E-02J023N5. Toshibas site, I downloaded all the drivers needed and bios. I started with the installation of the BIOS, when I tried to install it, then my pc froze.

  My food was on.
  The fan went beserk everything and the screen froze.
  I tried to let it run for 30 minutes, because I was afraid to interrupt the installation. I couldn't wait anymore, so I turned off the pc by removing the battery and power.

  When I then tried to turn on the laptop, nothing happens. All black screen.

  Can anyone help? I used the correct BIOS driver of Toshiba's own home page, but apparently it didn't work. How do I restore the BIOS? I don't know what BIOS I use.

  What I've done so far is:

  1. use HP USB Disk Storage Format Tool with MiniDOS files to make your Flash Bootable drive: USB
  2 copy all the files from backup for your: USB key
  3 rename your BIOS to bios.wph file and copy it in your: USB stick. I downloaded the same BIOS firmware and downloaded as EXE file, I extracted the exe file and found a file called. ROM and I renamed the entire file in bios.wph
  4. remove the battery, unplug the computer from power.
  5. hold: Fn + B, then all in now the computer in power (do not connect the battery) and close the power button.

  But after that, nothing happens.

  I'm afraid that something was wrong during the update of the BIOS of m.
  It seems that your ROM module, where are stored the BIOS was not flashed properly.

  I guess you checked this thread because the procedure described is her even that you posted your message.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=54395

  However, maybe you should try the procedure using the floppy and disk crisis described in the other thread.

  If this is not enough, your final option is the Toshiba service partner.