SG500 5 GB SFP module

Similar Questions

• DWDM SFP modules - where to use?

  Hi, we intend to interconnect two sites using DWDM. What type of SFP modules (color, color No 1310) should we use on our connection to the multiplexer/OADM switches? Does rely on the real device of MUX?

  DWDM and OADM multiplexers filters have ports specific wavelength, which are connected to an optical transmitter/receiver of the same wavelength.  Here is a link to the pluggable optical transceivers of Cisco DWDM

  http://www.Cisco.com/en/us/products/ps6576/index.html

  Cisco DWDM filters options linked below:

  http://www.Cisco.com/en/us/prod/collateral/modules/ps5455/product_data_sheet0900aecd806a1c36.html

  http://www.Cisco.com/en/us/products/HW/optical/ps1996/products_data_sheets_list.html

  Optical TRANSCEIVER for hardware compatibility

  http://www.Cisco.com/en/us/products/HW/modules/ps5455/products_device_support_tables_list.html

  Let us know if you have any additional questions.

• Channeling ether on two different sfp modules

  Hi Experts,

  I would like to know if a channel of ether can be created using two different SFP modules IE using

  GLC-sx-mm and glc-lh-sm on a switch or any other device.

  Thank you

  Abdul Malik.

  I have tried something like this in production. But bearing in mind that you can group copper and SFP interfaces in etherchannel so they have the same speed, L2/L3 config etc I think it's possible... but not 100% sure

  HTH,
  Dragan

• For Fast Ethernet SFP modules

  Hello

  We are looking for fiber-to-ethernet converter.

  Is there any SFP module that plugs directly into the Fast Ethernet to a switch port.

  Please visit the following link: -.

  http://www.Cisco.com/en/us/prod/collateral/modules/ps5455/ps6578/product_data_sheet0900aecd801f931c.html

  He said "the Cisco100BASE-X Form Factor Pluggable SFP (Small) (Figure 1) is a hot output device that plugs into the Fast Ethernet ports, dual rate Fast/Gigabit Ethernet ports or Gigabit Ethernet from a Cisco switch ports or a router, which connects the port with the fiber cabling network.".

  If this module can be plugged into any port of FE, is it compatible with Cisco switches only?...

  Please reply,

  Thank you

  Amit

  The SFP port is just a place where the optical SFP is sitting in the switch (connect internally to power, data bus, etc.). SFP offers you the possibility to install a plug-in to adapt to the requirement of the network; If short-range fiber, fiber long reach or same RJ45 without changing an entire line card or switch.  SFP ports are integrated in the switch by a manufacturer, not bolted on after.  The specification for the connector module and SFP interface is detailed in an SFP MSA (multi-source agreement); designed to offer a platform in the industry to build.

  If your switch has a fixed electric port and you do not have access to power (for a converter to media or other), then the terminal switch will be replaced by a device with a fiber interface option. That, or you'll find a power on fiber system with enough power to drive a Media Converter (which I don't think that there are still).

  I hope this helps!

• HP J4853A and Cisco SFP Module 100BASE-FX

  Hi all!

  HP J4853A and Cisco SFP Module modules 100BASE-FX is not compatible?

  Thank you!

  Both are 100Base FX for at layer 1, they are interoperable.

  Higher tier features will not be handled on one platform or another.

• can I use both optical and fiber sfp modules?

  Hello

  I have 2 stacked 3548 P PowerConnect switches. The top switch got uplink fiber of 1 MM (G1) to another switch in a different building. If the top switch has 1 free uplink port and the lower 2 switch free uplink ports. Recently, we bought 2 servers Poweredge R620 and I would like to connect them to the Gigabit ports. The 'normal' switch ports allow only 100 Mbit/s, so I plan to buy 2 modules SFP 1000Base-T (for copper) to connect to them.

  Is this feasible? Can I use G2 on the top switch for SFP 1000Base-1 T? Is this allowed?

  Kind regards

  Erik

  Yes, it's quite feasible. The connection will be configurable the same 100 Mbps ports. Here is a link to the part number for the 1000Base-T transceiver.

  http://bit.LY/1JI5MMe

  See you soon

• Cisco WS-C3750X-12 s - S SFP modules

  Dear team

  I required 12 new sfp port switch I chose WS-C3750X-s-12s
  for my requrement is here my question is...

  Is I need to add separate trancievers SFP for this switch or not?

  Care technical I have not found that rock come alongwith 12 trancievers then how can I configure this procudt

  Hello

  The X Catalyst 3750 - 12s switch is a based FPS you don't need SFP transceivers. Take a look at table 6 to the Cisco Gigabit Ethernet transceiver Modules compatibility matrix for details on the supported transceivers and the OS release that they are taken care of.

  Concerning

• Cisco SFP module name

  What is the difference between the module two next?

  SFP-GE-L = vs SFP - GE - L, we have = to sigh at the end and others are not.

  http://www.Cisco.com/c/en/us/products/collateral/interfaces-modules/Tran...

  SFP-GE-L	1000BASE-LX/LH SFP (DOM)	GLC-LH-SMD	1000Base-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM	-
  SFP-GE-L =	1000BASE-LX/LH SFP (DOM)	GLC-LH-SMD =	1000Base-LX/LH SFP transceiver module, MMF/SMF, 1310nm, DOM	-
  SFP-GE-S	SFP 1000BASE-SX (DOM)	GLC-SX-MMD	1000BASE-SX SFP transceiver module, MMF, 850nm, DOM	-
  SFP-GE-S =	SFP 1000BASE-SX (DOM)	GLC-SX-MMD =	1000BASE-SX SFP transceiver module, MMF, 850nm, DOM	-

  For all Cisco SKU (Stock keeping units), the '=' at the end means a piece of spare or ordered separately article.

  Without a '=' means usually the exact same item is ordered in a parent configuration - for example, a SFP as an optional part of a module switching.

  They are exactly the same physical part.

• PowerConnect 5324 SFP Module

  Hello

  I have a PowerConnect 5324 and a "QLE2462 PCI Express 4 Gb FC Dual Channel".
  What modules I need to buy to make them talk to each other?

  The seats of switch on the server, so I'm sure I need a SX module.

  I have no knowledge on the FC so a deep answer really appreciated

  This will be my homelab so nothing of quality required

  Kind regards
  Andrzej

  Hello

  The switch supports modules 1000-SX and 1000-LX. Those aren't Fiber Ethernet, fiber channel storage. The 5324 does not support the Fibre Channel.

• Trouble connecting Netgear XS748T to Ubiquiti UniFi US-48-750W via Port SFP +.

  We bought a new switch Netgear XS748T and try connecting to our existing network which consists of several switches of Ubiquiti UniFi US-48-750W, and we try to connect using the SFP + 10 GB ports on the two switches. We have a Direct Link SFP + SFP + DAC, passive, 1 m, cable AWG30, we bought at Amazon / 10Gtek and when we try to use this cable between the Ubiquiti switch and the Netgear we get no link activity.

  However if we use the same cable between two of Ubiquiti switches it lights immediately and works very well, the same is true if we use the same SFP + cable between the switch Netgear XS748T and a XS728T that we must also. Its almost as if the switches detect the same manufacturer at the other end and right link up but when its manufacturer another pass on the other end, it does nothing.

  It is very aggravating, and Im going to be obliged to return the new Netgear switches. Can someone make a suggestion or confirm if they should or may not work? Everything simply connecting switches together using a cable of copper works very well but since our current switches don't support 1 GB via copper it provides not enough bandwidth for our use so we really need the port SFP + 10 GB to give us the uplink.

  Here is a link to the modules SFP + cable, we bought:

  https://www.Amazon.com/DP/B01LSGGUOY/ref=twister_B01M0ER4M0?_encoding=UTF8&PSC=1

  It seems that I solved the problem myself. I bought a set of:
  10Gtek for Cisco SFP - 10 G - LR, 10 Gb/s Transceiver SFP + module 1310nm 10km

  And the LR version worked instantly. I honestly don't know what's the difference between a SFP + SR module and a module LR SFP +, but for some reason any LR module has allowed these two switches to connect.

  Here are links to the modules and the cable used in case anyone needs a solution to this:

  LR SFP + Module:
  https://www.Amazon.com/GP/product/B00UMS905G/ref=oh_aui_detailpage_o00_s00?ie=UTF8&PSC=1

  Fiber cable:
  https://www.Amazon.com/GP/product/B00T5796DQ/ref=oh_aui_detailpage_o00_s00?ie=UTF8&PSC=1

• PowerConnect 2824 Ports SFP does not

  We bought a new switch 2824 with a corresponding to SFP module replace old 2724 PowerConnect and SFP module.

  After the configuration of the switch and installing it, we were able to get a connection on our uplinked to fiber.
  SFP light illuminates and flashes from time to time, and the switch detects correctly module SFP is inserted and that the fiber is connected.  We can see the insertion of the SFP is detected and the switch for change of fiber mode by looking at the output of the console, and the web administration port status page lists the port as "ComboF" when the SFP is inserted and the fiber is connected.

  However, the switch always indicates that the port State is down.  (The port is not administratively disabled.)

  The old switch works very well with the old SFP module.  The new switch does not work with the old or the new module SFP.  We tried two combo SFP ports.  We also checked that the fiber itself is fine. We cannot get the new switch to display the drop-down list port status that up when you use the SFP. We tried to completely reset the new switch by removing the configuration file via the boot over the serial connection menu and re-run the initial configuration wizard, but the port still won't go up.

  Any ideas?

  After a few tests yesterday, we determined that part of auto-negotiation must be disabled for switch work with our copper and fiber Media converters.

  The 2724 works very well with our media converters, with auto-negotiation enabled.

  The 2824 works very well with auto-negotiation enabled when it is connected to an another SFP transceiver in building switch.

  But when we introduce the Media Converter in the path, the 2824 will bring only the link up if you disable auto-negotiation.

  So far, everything looks good.

• PowerConnect 6224: Dell SFP + port supports combine Dell SFP?

  I have a Dell Powerconnect 6224 switch and I installed a Dual Port SFP + Module of adaptation for PowerConnect
  6200 series at bay2 at the rear of the switch. I inserted a transceiver, SFP 1000BASE-LX, wavelength 1310nm 10km Reach in the SFP slot + and the other end is connected to a connector SFP 1gbe. I don't have any link. My question is if Dell SFP ports + supports SFP transceivers or it only supports SFP transceivers +?

  I checked the ports to help an SFP + SFP +, 10GbE, copper Direct Attach cable Twinaxial, and link LEDs are lighting up.

  I believe that the SFP ports + back work with SFP transceivers. Ports before combo will work with SFP transceivers. Another thing to look at is the cable being used. Don't forget that there are specifications that are compatible with transceivers FPS are you wanting to use. A SFP + SFP connection would require that the SFP transceiver + supports a connection of 1 GB.

  Hope this info helps.

• 62xx to 62xx via SFP + 10GBase-LR

  Hello world

  a battery consists of two 6224P, I use two FC SFP + modules (couldn't dig up D/PN, wink will be soon attached)

  g23 mastery (but any other SFP +) via FC to third 6224P

  now I see that the link is there, at least both ends indicate link is there and no problems reported, yet...

  I can't start with, both ends ping each other

  I like to leave the third switch in stand-alone mode, just a CF link between it and the battery

  Why they can't see each other? needs to check/make sure first?

  Thank you very much.

  You want to switch master/general switchport mode implemented on ports for connection of the battery and the stand alone. On the PowerConnect 62xx switches, you must use general mode if you want to allow traffic from management on the switch on the PVID.  If you use the Trunk mode, you will not have the default VLAN on these ports.  The ports will only allow labeled traffic.

  example of

  Console # configure

  Console (config) # interface ethernet e11

  mode console # switchport general

  Console # switchport General allowed vlan add 100 tag

  Console # switchport General allowed vlan add 200 unidentified

  Console (config-if-1/g1) #switchport pvid General 1

  Console # end

  This suppose you are wanting to connect switches only to layer 2 and layer 3 (routing).  If you route and want to switch to communicate through Layer 3 you will need a range of IP addresses and isolated VLAN. Then, set connection ports between the devices as a switchport access with the specified VIRTUAL local network.

• Connection of 10 x SFP - 10 G-SR-S to an Interface of 1 G

  Hello

  I have a router ISR4451-X, which comes with 4 x 1GE interfaces, and I want to connect it to a switch C4500-X, which comes with 16 x 10 G interfaces. I use SFP - 10 G-SR-S on the C4500 and want to know what SFP module, I need to use on the ISR4451 to plug these devices together.

  It is even possible to connect a router that has a 1GE to a switch that has a SFP 10 G-SR-S?

  Thanks in advance.

  Best, ~ zK

  No - you must use a facility such as either:

  1 GLC - T (copper 1 Gbps transceiver) to 4500-X end in the regular cat 5 copper interface on the router, or

  2. something like the GLC-SX-MM (transceiver Gbps fiber multimode 1) at both ends.

  A SFP 10 G-SR-S cannot connect to any or 1 Gbps transceiver interface. 4500-X SFP ports are backward compatible and accommodates 1 Gbps SFP transceivers.

• can you connect the SFP - 10 G - SR low-support to SFP 1000BASE-SX?

  Hello world:

  today I use the SFP + 'SFP - 10 G - SR' in Cisco Catalyst 2960 S-48TD-L connect to the SFP 1000BASE-SX to 6509 WS - X 6724-SFP module.

  the port setting is master, but they do not work, even the light don't flush. Then, I also use the SFP 1000BASE-SX to replace SFP + SFP - 10 G - SR in

  2960 S-48TD-L, then they cany working.

  I look to the top of the cisco data sheet, there is no roadmap to satament database 10G sfp + can't low support 1 G sfp. So, I want to confirm the problem.

  Otherwise, the 10 FPS + can only use for 10G SFP +; can't go down the suport 1 G SFP.

  This means: If you want to use the 10 G SFP + the other old device also need to replace.

  Thank you ~ for your help!

  Hi Marvin,.

  I found this conversation today, because I'm looking for an answer on a question similar to the question that Jerry asked, at the opening of this discussion.

  So my problem is this. In a certain place, I need two 10 GB and a connection of 1 GB on an optical cable. To cut costs, I tried with WS-C2960X-48FPD-L, but because it contains only two ports of SFP +, I tried with two WS-C2960X-24PD-L which will be connected with the battery modules.

  Then, having two WS-C2960X-24PD-L, I have 2 x 2 ports SFP + 1 GB. There are two open questions:

  1. can I put 1 GB transmitter SFP module SFP + port (that I have a connection of 1 GB at remote site)?

  2. can I use two switches to 24 ports mentioned 2960, in a way that I use one of them for the two connections of 10 GB (using ports SFP + 10 GB connection) and the second member of the battery so that we (2 available) port SFP + is used to 1 GB SFP connection (using the SFP port + as mentioned in question 1)?

  I'm not sure if your previous statement covers my questions, because it is not clear if the 1 GB SFP transceiver can be inserted in the port SFP + WS - C2960X - 24PD - L (or any other a port SFP switch +).