Shortcut to connect to the nearest tower

Similar Questions

• PC to tv connection error "no signal - check the connections and the external device is turned."

  Original title: pc to tv connection

  I have an Acer Espire Vista 32bits. Connect to a Panasonic TC L32x30 HD TV. The TV has a 'PC' marked port that matches one VGA cable. I have the VGA end of the cable is connected to the TV. The other end is connected to the PC Tower via a DVI adapter to the port where was my monitor.
  TV output is set to "PC". I turned on my PC, the Acer (Bios) screen came. He then shows the block scroll bar. Just as Windows is about to light up, cutting signal. I never get to see my office. A message appears on the screen saying "no signal - check the connections and the external device is turned on."
  I had posted before saying that I had problems ranging from VGA to VGA. That's why I bought the DVI adapter to try another solution.
  I hope I made things clear enough for someone to help him.

  Hello Winston M,.
  I actually solved it. Went to the screen and chose. Connection just how I mentioned. second monitor, default Says. I then checked"Extend Desktop to this monitor.
  As I type this, I can see it on my TV screen.
  Thank you for taking the time to answer my question.
  Problem solved
  Ray

• Windows 7 PCs are not connected to the closest access point

  Windows 7 PCs are not connected to the nearest access point.  Any ideas?

  For example:

  We have AP 1 and 2 of the AP for exaple.  They have the same SSID.  AP 2 is further with a bad signal.  AP 1 is closest with an excellent signal.  Why my laptop does not connect to the AP 1?

  You MUST use the same SSID.  I think that you misread my post.

  And Yes, a channel problem is that what I have proposed.  You can try to configure access points using the 3 discrete channels (1, 6 and 11) to minimize any overlapping units to the same channel coverage.
  At least this is the traditional way, we do it, although the automatic selection increases common and 11n 40 Mhz channels (if defined in this way) are also in.

• Full service then no appeal abandoned service cannot connect to the Tower

  Posted to help others:

  I bought an iPhone 6 s it took 3 hours for Verizon connect my phone to my new Verizon account. The phone would display full service bars then, slide an or no service in bars. the phone was finally connected but may 2016 so far I sill experience the same problem of poor or no service call and dropped. Often the phone will not even scream or try to connect to the network.  Apple has replaced the phone 3 x but with no. change my service problems. Verizon and Apple senior level tech support spent to treat 30 + hours on the phone with me trying to solve this problem. We replaced the SIM cards without change. When I put the SIM card in my iPhone 6 it works fine. Full don't signal any calls interrupted and service when roaming. Back in the 6s and no service in the same place. Put the SIM card in the other Iphones not without problem.  If roaming is enabled, phone often it will not conbect to the tower at all. WiFi call is disabled and LTE voice data are on. I've disabled CDMA and data with little or no change with the problem. When iphone 6s loses the service and I toggle airport power phone it will display momentarily full service bars, then the bars one or not, while remaining connected to LTE. In some areas, I can receive calls but can not shout. Sometimes I can txt use data without showing on my plan as using FaceTime and can use the internet. The order indicated above of multiservices to no service happens within 10 seconds repeat throughout the day all areas companies Verizon towers and riaming towers. Verizon finally got the iPhone 6 s to work with full signal across remote I've ever had service, but continue to hamper the not being able to call in roaming. Shortly after that, the phone back to old habits after that they tried to solve the roaming problem.

  After 5 months of no stop calls to Verizon senior level tech supports on September 22, a high tech support tech senior level line finally came to the conclusion after 3 hours of troubleshooting determined it is a software problem Apple 100%. It determined that the phone for a month not was not connected totally to Verizon even if I used it. There to reset the SIM card and the network settings on the phone several times during this period to have the phone drop any connection after initial power that showed a full service then dropped the LTE then, he loses all the bars of service then shows no bar service then no service what so ever in 10 seconds. This was the problem with this phone on the first day.

  He explained that he has heard of what is happening and that Apple is currently working on a solution, but will not be out until possibly October 2016. He also said that this problen is happening now with new models Iphone 7.

  HE then stated that a specific sequence is usually not used must be used to reset the network settings by releasing the bug fix.

  How to restore your device

  1. First of all, back up your device using iTunes or iCloud so you don't lose any personal information.

  Note: If this is the first time that you have saved on iCloud, it may take time for several reasons (speed of Wi - Fi, amount of info on your device).

  2. Connect to iTunes to restore your device. 3. Choose "Set Up as new". 4. Make sure you that you connect to iCloud with your Apple ID so that only your contacts are re-added. Do not re - add photos, music or applications as they can be the source of your problem. 5. Set up your email. 6. Test for the next few days to determine if your problem has been resolved. 7. Restore your backup from iTunes or iCloud.

  Note: If you have a food problem, try to use the recovery mode.

  I hope this helps someone it is to have the same problems. I'm waiting to see if the bug fix works otherwise I'm going to an android phone. It has been too long a process without having a phone that works.

  I have the same problem - it has taken far too much time out of my weekend to try to resolve this problem. In addition, the Apple support person I spoke on the phone was very condescending.

  I've read elsewhere that change the LTE cell Options > Data Only will not solve the problem. So far, this seems to have worked for me.

• The place most frequent that I need to connect to a BT hotspot has a problem with the nearest hotspot. Although many sites come they are security protected.

  Access to the BT hotspots.

  The place most frequent that I need to connect to a BT hotspot has a problem with the nearest hotspot. Although many sites come they are protected from security and only the nearest BT hotspot is displayed. There are many others, but they are invisible. I think that there is a software that allows you to see several hot spots the. BT are unable to give me the details.

  This is probably a function of the driver for your wireless card.  I would check with the manufacturer of the computer or adapter.

  Good luck.

• How can I get firefox to launch automatically on connection to the internet

  I want that firefox will automatically launch when I connect to the internet

  Put a shortcut to Firefox in your Windows startup folder?

• With 2 monkeys roaming network connected to the internet

  Hello

  My apologies if this has been discussed (I did some search but did not find anything useful). I have the question realted following a change in my network topology:

  current installation:

  -Cable modem is connected to the WAN port on my Time Capsule (3 TB Tower). Transport CANADA acts as DHCP unit (modem is silent, that is without router)

  -Port LAN of the TC is connected to the WAN of the MONKEY #1 via CAT6 Ethernet port.

  -MONKEY port LAN #1 is connected to the WAN of the MONKEY #2 port

  -Port LAN EPA # 2 is connected to the WAN of the MONKEY #3 port

  -all the monkeys (the latest models of Tower) Act in Bridge mode, but create a WLAN.

  I like that, a roaming welll workign network throughout the House.

  New installation / planned:

  -J' changed from cable to fiber to the home. So now I have a new box of fiber that offer Internet via 4 Gigabit Ethernet ports.

  -The new fiber box is physically located between the TC and the #1 MONKEY.

  -without having to pull a new cable in the box of fiber for the TC (for feed on the Internet in the beginning of the string), I was thinking about this:

  -1 Ethernet cable from fiberbox to the TC and feed the Internet through another Ethernet into the WAN port on the #1 MONKEY in the remaining string.

  -Switch the TC using the Bridge so that the fiber box making the DHCP

  However, now the TC is is more directly connected to the chain of the EPA.

  QUESTIONS RELATING TO THE:

  -I'll always be able to have a mobile network, or I will with 2 networks, i.e. 1 created by TC and 1 piloted by monkeys?

  -all Clients on the network will see always shared devices (printer, for example) on the network?

  Thank you very much for your expert advice on this.

  Rgds,

  Sascha

  -run 1 Ethernet cable from fiberbox to CT...

  -Switch the TC using the Bridge so that the fiber box making the DHCP

  It should work.  (See Note below)

  feed the Internet through another Ethernet into the WAN port on the #1 MONKEY in the remaining string.

  It should work. (See Note below)

  However, now the TC is is more directly connected to the chain of the EPA.

  Since the TC is connected to Ether even switch on the product of the fiber to which EPA #1 is also connected... TC and AE #1 are, indeed, also linked together.

  I'll always be able to have a roaming network

  Yes

  -all Clients on the network will see always shared devices (printer, for example) on the network?

  Yes, assuming the fiber box works properly.

  Important note... Your plan to have the TC and the MONKEY in Bridge Mode expected to work... BUT... Apple has another idea on how a mobile network should be configured. See the information on a roaming network in this Apple support document:

  Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo...

  More precisely... Apple will tell you to connect an Ethernet cable from the product of the fiber to the WAN on the TC port and set the TC for managing DHCP and NAT... just as it does now.  Then... all the rest would be put in place just as you have it now... with a connection Ethernet between a LAN port on the TC to the WAN on EPA #1, LAN on EPA to WAN on EPA #2 #1, etc..

  If you follow the advice of Apple... you'll get an error Double NAT on your network... Apple who will tell you to ignore. How well your network will work with a Double NAT problem is open to question.

  I don't recommend to follow advice Apple... just pointing out that Apple has different ideas and interesting on how to do things, which sometimes goes against the traditional rules of network management.

• OfficeJet 4630: Unable to connect to the printer

  I have been using an Acer laptop with a HP printer via a wireless router.  I had to replace the printer with a 4630, which is wireless, still has a USB port in the back.  I connected the cable from my tower to this port, then made the setup wireless according to instructions.  The printer works with the office, but not the laptop via the router.  I get no error message, nothing happens when I try to print.  Although it is a simple operation, I'm in over my head, being almost totally ignorant of Windows.  (With the help of Windows 7).  I guess the problem lies in how I have the laptop implemented, even if the old printer works perfectly with the desktop and the laptop.   The printer reported that it was connected after that I did the installation, and I have the blue light.  I know that the laptop can still access the router, as I have no problem connecting to the Internet.  Suggestions as to how I should have the laptop configured?

  Also, I got this message after you posted my message, but do not see what has been changed: "your message has been modified because the incorrect HTML code was found in the body of the message. Invalid HTML code has been removed. Please review the message and send the message when you are satisfied. »

  I solved my problem.  As I suspected, the problem is with the configuration of the laptop.  I deleted the network information and it built everything back, and now I can print to the desktop via a USB cable and the laptop through the wireless router.  Thanks for your efforts.

  RG4

• SK2061: The wireless keyboard will not connect when the PC is turned on.

  My problem is, when I start the PC, (HPK-15 500, 319NA), wireless (SK2061) keyboard, does not connect. I have to shut down the PC so he can connect (no restart, you must stop it).  Have had the PC for 5 months and it has been published. Not changed the battery makes no difference.

  The internet statement States I shoud push the blue button until the USB receiver flashes. This PC does not have an external USB receiver, I guess it's built in! The mouse works OK.

  Hello @JimCar82,

  I read your post on how the wireless keyboard will not connect when the computer is turned on, and I'd be happy to help you in this case!

  Re-connect your keyboard to your desktop computer wireless, I advise you to follow the steps described in this document on the keyboard and wireless mouse troubleshooting. The USB receiver should be found at the back of the tower.

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• HP Officejet Pro 6830: HP Officejet Pro 6830 - unable to connect to the computer

  Hello

  I just replaced my Officejet6500 with an Offiejet 6830

  I have lived throughout the configuration stage until the software looked for the printer and it cannot be found. the printer is confirmed as connected to the same network as the computer's wireless so I don't know why it is not to be discovered

  Any help would be appreciated

  Thank you very much

  Mike

  Hey @mfbar,

  Welcome to the Forums of HP Support!

  I understand that printer e-all-in-one Officejet 6830 and your Mac OS x 10.10 machine are not communicating. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  Turn the printer off.

  While the printer is turned off, remove the power cord at the back of the router for a minute.

  When the lights come back on the router, turn on the printer.

  Now on the printer, click on the wireless icon that looks like a radio tower.

  • If the IP address starts with 169.254, the printer is not getting a valid IP address. Contact your internet provider or one that provided you with the router for assistance in ensuring the router assigns IP addresses.
  • If the IP address starts with 172, the printer is connected to a network of comments. Contact your internet provider or one that provided you with the router for assistance with deactivation of the feedback network.
  • If the IP address begins with 192.168, the printer is properly connected to the network. Please see below.
  • If the IP address begins with any other number, the network is maintained. Contact your computer or the one who manages the assistance network.

  Once the above is done, if the Mac is still not able to detect the printer then the next step is to contact your internet provider or the one who provided the router. When you do, ask them to:

  • Open all ports.
  • Select multicast.
  • Disable MAC filtering/MAC cloning.
  • Make sure that the router has a band of 2.4 GHz (gigahertz).

  Please let me know the results after following the above. If you are able to connect to your printer, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Acquire the msg network but cannot connect to the internet?

  I Tower IBM 'Think pad' and when I try to connect to the internet, it is said ' acquisition of network and it connects don't not in the network, the bars keep fluctuating between 2-4 bar, but still won't connect, a 'fix' I tried it same thing... will to "acquire the network but does not connect."

  What seems to be the problem, what do you suggest to please. It was working fine until last night.

  Have you tried restarting your wireless router? It off for a few minutes, then turn on and wait a few minutes and then restart your computer.

  I hope this helps.

• I can't connect to the internet after the elimination of the virus and new restore point.

  I use IE8. I can only connect to the internet in safe mode with network.  What can I do to connect to the internet in the normal windows?

  Hello

  When parasites get installed on your computer, they might create hooks in the system computer activities related to the program "Junk" files  When you get rid of the 'Junk' hooks could remain in the system, in the absence of target files (they cleaned) problems are created in the network and Internet related activities.

  If after uninstalling the "Junk", the Internet connection does not work as it should, you will need to restart the operating system parts which get trashed by the process.

  WinSock and TCP/IP update.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  The same processes to refresh the TCP/IP replaces the command typed with.

  netsh int ip reset press enter

  ipconfig/flushdns, press enter

  Restart your computer.

• System Event Notification service - cannot connect to a Windows Service. Windows could not connect to the System Event Notification service

  I am unable to connect to my network wireless with my laptop Sony, (Vista home premium). This follows an infection in my desktop PC with a Trojan which did not stop, but slow internet browsing. I reinstalled vista windows on the pc and it works fine now bur my still gives mobile me this message. "Unable to connect to a Windows Service. Windows could not connect to the System Event Notification service. This problem prevents limited users to logon to the system. As an administrator, you can view the system event log to see why the service did not respond. "I am the administrator on my pc and laptop. I tried to change the user nothing helps. I use Vista Home Premium Service Pack 1. Intel Core 2Duo T7250 2 GHz. 2 GB of RAM. 32-bit. Sony Vaio FZ31M. If you can give me instructions on how to remedy the situation, it would be appreciated. Thank you, Tony

  Hi 1234Tony,

  First of all, I suggest you that you also scan your laptop for infection by the virus. Second, reset TCP/IP stack Winsock settings. This could correct mistakes involving internet connectivity as a result of problems of installation of network software, due to a virus, trojan or malware infection or even due to disinfection of spyware security software.

  To repair and put back the Windows Vista

  1. Click the Start button.
  2. Type Cmd in start it the search text box.
  3. Press Ctrl-Shift-Enter keyboard shortcut to run command as administrator prompt. Allow elevation request.
  4. Type netsh winsock reset in the command line shell, and then press the Enter key.
  5. Restart the computer

     If please reply and let us know if your problem is resolved or if you need further assistance

  David O
  Microsoft Answers Support Engineer
  Visit our and tell us what you think.

• Unsuccessful login message - error message after "connection to the network is taking longer than usual"

  -All right, so I won't try to describe my problem by telling you what happens when I try to connect to any other network that my own home network (a school, work, network etc.).

  First of all, I try to connect and I get the message:

  "network connection takes more time than usual ' which of course is soon followed by the message"connection failed"after which said the logo of the network on the lower corner of the taskbar"

  this computer has limited or no connectivity"click to run a repair and three options including".

  automatically get new ip for the "wireless network connection" network card settings«»

  Reset the network adapter', and there is no internet here (I'm paraphrasing this one of course). "

  Now, sometimes if I click on one of the service options and the connection starts immediately, sometimes I have to click two options, one after the other fails to solve the problem, sometimes, I have to click on them each several times before it works (you one and two of another, for example).

  most of the time receiving the message ' windowstried a repair but a problem persists. " This computer has limited or no connectivity"between the stages of repair. I know that of not explore because I used mozilla firefox and google chrome and I get the same problem. I even tried to reboot once the connection has failed the first time. My computer is up to date and I have passwords for my school and respective secure networks of works.

  Y at - it as any indication of what could happen here for me to have to reset and click and wait and fix almost every time that I get on any network, but my home network?

  Thank you for your time,

  Bryan

  Hello

  Hello

  You scan the computer and make sure that it is clean of viruses and malware.

  Download the latest drivers for the wireless card from the support page for the manufacturer of the laptop computer and update the drivers for the card.

  After that.

  WinSock and TCP/IP update.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  The same processes to refresh the TCP/IP replaces the command typed with.

  netsh int reset Press enter

  ipconfig/flushdns press Enter

  Restart your computer.

  -----------------------

  Uncheck the box to the NIC of energy economy (I.e., do not leave the card save energy).

  There may be some variations on where is the energy saving setting.

  Here are a few examples, YMMV, look around your systems.

  Example, http://www.ezlan.net/example/powersave.jpg

  Example, http://www.ezlan.net/Win7/power_sav_wireless..jpg

  Example, http://www.ezlan.net/Win7/power_save_win7.jpg

  Example, http://www.ezlan.net/Win7/adv_power-sav.jpg

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• "lcwipx.exe of shortcut that you refer to is not available" and her does not open. He also asked delete me the shortcut. What is the problem and how to solve this?

  When connect my external hard drive and opening not wanting my my files, I get this message "shortened lcwipx.exe you make reference to is not available"and her does not open. He also asked delete me the shortcut. What is the problem and how to solve this?

  Hi Pascal,.

  I see that you get an error trying to access files on an external drive. I'll help you with this problem.

  1. What is the brand and model of the computer?

  2. What is the brand and model of the external drive?

  3. what security software is installed on the computer?

  4. have you made changes on the computer recently?

  5A external drive earlier good work?

  6. have you updated to Service Pack 2 installed?

  Method 1.

  Connect a different drive to the computer and check.

  Method 2.

  Plug this external drive on another computer and check the status.

  Method 3.

  Start the computer in safe mode and check.

  Start your computer in safe mode: http://windows.microsoft.com/en-SG/windows-vista/Start-your-computer-in-safe-mode

  Method 4.

  Run a full scan of the computer with the Microsoft Safety Scanner to make sure that the computer is virus-free.

  Microsoft safety scanner: http://www.microsoft.com/security/scanner/en-us/default.aspx

  Warning of Security Scanner: there could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Let us know if you need assistance with any windows problem. We will be happy to help you.