show ip route / routing table
Hi all
I have a question about the output of the command "show ip route":
C 192.168.30.0/24 is directly connected, Ethernet0
172.16.0.0/24 is divided into subnets, subnets 1
S 172.16.1.0 is directly connected, Ethernet0
192.168.38.0/24 is variably divided into subnets, 2 subnets, 2 masks
S 192.168.38.0/24 is directly connected, Ethernet0
192.168.38.0/25 S [1/0] via 192.168.30.40
10.0.0.0/32 is divided into subnets, subnets 1
C 10.1.1.1 is directly connected, Loopback1
I understand why the lines 4, 5 and 6 are present. Its cause, the 192.168.38.0 network is supposed to have a 24 mask but it is also a network with a 25 mask and so he said that this network is variably subnet.
But why it only shows the same for lines 2 and 3? -It should not say 172.16.0.0/16 is divided into subnets? I understand why is doesn't show "variably subnet" given that the subnet, but why not 172.16.0.0/16?
And the same for the last two lines. Why not 10.0.0.0/8 but 32? Even if it is a loopback interface always the 10.0.0.0 network is supposed to have an 8 mask by nature.
And maybe this is a stupid question but a static router always has a metric of 0? I think Yes, because they do not have to compete with other roads, right?
I mean a static route will always all right in the table routing and the metric is actually just for reasons of comparison within a routing protocol to see what is the best route that should be proposed to be written to the routing table.
I also tried to put static routes permanently in the with the "standing" order routing table, but always when I detach the corresponding interface cable routes get kicked of the RT. Y at - it a tip or something I should be aware of?
Thanks for any help!
I'll take the easiest part of the first question. One of the fundamental principles of the IOS is that it will put routes in the routing table is the corresponding interface is in a high State. And IOS will withdraw a route in the routing table are the corresponding interface is in the low state. So, when you log out of the interface, then the road using this interface is removed.
The most complex part of the issue is the appearance of the measures with static routes. My explanation here would start from the point that the reason that we use measures so that we can compare the routes recorded in a Protocol and determine whether one is better than the other. This has meaning for the RIP, it is logical for OSPF, and it makes sense for EIGRP. But it makes no sense for static routes. To try to make it a little more clear: If the RIP or OSPF or EIGRP to discover a route to a subnet that goes through FastEther0/0 and also learn a route to that subnet that goes via FastEther0/1 and then we compare the roads and if you have a more attractive metric, is the one who gets put in the routing table. But with static routes if there is a static route to a subnet that requires a static route for this subnet that goes via FastEther0/1 FastEther0/0 and also, so there is no comparison and both routes are placed in the routing table. Since we do not comparisons with static routes, so there is no concept of metrics associated with the static route and IOS puts a default value in the field of a static route metric.
HTH
Rick
Tags: Cisco Network
Similar Questions
-
NO OSPF routes in the database, but in the Routing Table (read you correct)
Hi all
I have a lab of two roads R1 & R2 (connected with Ethernet link) like:<------------------>R1, R2
I can see, OSPF learned routes are Routing Table, but not in the database (read you right).
How can it be possible? I saw the other direction several times i.e. the routes in the database but not in the routing table (like, VPN L3 remote end when we use the ability VRF-lite, or we try to remove from the interarea road of the LSA, but that is not the concern here)
I captured a few newspapers & running Setup two routers. Please check and let me know what I am doing wrong.
I erased the OSPF neighborship several times but still the same. Tried to bounce e1/1 on R2, but no luck.
R2 #ping 3.3.3.3 lo3 Yes
Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 3.3.3.3, time-out is 2 seconds:
Packet sent with the source 2.2.2.2 address
!!!!!
Success rate is 100 per cent (5/5), round-trip min/avg/max = 64/76/108 ms
R2 #.
R1
R1 #.
R1 #show int ip short bones
Interface area PID IP address/mask cost of State Nbrs F/C
Lo0 9.9.0.1/32 LOOP 1 1 0 0/0
Lo3 3.3.3.3/32 LOOP 1 1 0 0/0
Et1/0 1 0 9.9.12.1/24 10 DR 1/1
R1 #.
R1 #.
R1 #show ip ospf da
Router OSPF with ID (9.9.12.1) (process ID 1)
Router link States (zone 0)
Number of links ID ADV router age Seq # Link Checksum
9.9.12.1 9.9.12.1 255 0 x 80000028 0x00BE86 3
9.9.12.2 9.9.12.2 256 0 80000032 0x0067F8 x 2
NET link States (zone 0)
Link ID ADV router age Seq # Checksum
9.9.12.1 9.9.12.1 255 0 x 80000003 0x00BDFC
R1 #.
R1 #.
#show ip route R1 | b door
Gateway of last resort is not set
2.0.0.0/32 is divided into subnets, subnets 1
O 2.2.2.2 [110/11] via 9.9.12.2, 00:04:17, Ethernet1/0
3.0.0.0/32 is divided into subnets, subnets 1
C 3.3.3.3 is directly connected, Loopback3
9.0.0.0/8 is variably divided into subnets, 3 subnets, 2 masks
C 9.9.0.1/32 is directly connected, Loopback0
C 9.9.12.0/24 is directly connected, Ethernet1/0
The 9.9.12.1/32 is directly connected, Ethernet1/0
R1 #.
R1 #.
R1 #show ip os not
Neighbor ID Pri State Dead Time Interface address
9.9.12.2 1 FULL/BDR 9.9.12.2 Ethernet1/0 00:00:36
R1 #.
R1 #.
R1 #show run | s r o
router ospf 1
Log-adjacency-changes
R1 #.
R1 #.
************* R2 ********************
R2 #.
R2 #show int ip short bones
Interface area PID IP address/mask cost of State Nbrs F/C
Lo3 2.2.2.2/32 LOOP 1 1 0 0/0
Et1/1 1 0 10 BDR 1/1 9.9.12.2/24
R2 #.
R2 #.
R2 #show run | router s o
router ospf 1
Log-adjacency-changes
passive-interface Loopback3
2.2.2.2 network 0.0.0.0 area 0
Network 9.9.12.0 0.0.0.255 area 0
R2 #.
R2 #show da os ip
Router OSPF with ID (9.9.12.2) (process ID 1)
Router link States (zone 0)
Number of links ID ADV router age Seq # Link Checksum
9.9.12.1 9.9.12.1 326 0 x 80000028 0x00BE86 3
9.9.12.2 9.9.12.2 325 80000032 0x0067F8 0 x 2
NET link States (zone 0)
Link ID ADV router age Seq # Checksum
9.9.12.1 9.9.12.1 326 0 x 80000003 0x00BDFC
R2 #.
R2 #.
R2 #show ip road | b door
Gateway of last resort is not set
2.0.0.0/32 is divided into subnets, subnets 1
C 2.2.2.2 is directly connected, Loopback3
3.0.0.0/32 is divided into subnets, subnets 1
O 3.3.3.3 [110/11] via 9.9.12.1, 00:05:22, Ethernet1/1
9.0.0.0/8 is variably divided into subnets, 3 subnets, 2 masks
9.9.0.1/32 [110/11] via 9.9.12.1, 00:05:22, Ethernet1/1
C 9.9.12.0/24 is directly connected, Ethernet1/1
The 9.9.12.2/32 is directly connected, Ethernet1/1
R2 #.
R2 #.
R2 #show ip os not
Neighbor ID Pri State Dead Time Interface address
9.9.12.1 1 FULL/DR 00:00:30 9.9.12.1 Ethernet1/1
R2 #.
R2 #.
Hello
an OSPF router generates only a router-LSA (Type-1) by Area.This router-LSA contains a list with all the links in this area.
You can see your telesignalisations with 'show ip ospf router of database' - 'show ip ospf database' rather an overview:
Router Link States (Area 0)Link ID ADV Router Age Seq# Checksum Link count9.9.12.1 9.9.12.1 326 0x80000028 0x00BE86 3
Router 9.9.12.1 announces a router-LSA for area 0 and the LSA contains 3 links. Apparently, you created the Loopback IPs when adjacency was already formed, if not the router ID would be defined the highest loopback IP (maybe that's the reason for your confusion). HTHRolf -
DMZ-Link bandwidth does not change the routing table countin traffic
Hey guys
I'm INE laboratories dong and shoved a weird one that delivers.
I have configured the dmz-link bandwidtha nd the extended communities to send, I get the bandwidth in the BGP routes, however the routing table does not change the proportion of traffic according to the bandwidth available link.
Here is my configuration:
Rack1R6 (config) #do sh run | dry BGP
router bgp 100
no synchronization
The log-neighbor BGP-changes
BGP dmzlink-bw
155.1.146.0 netmask 255.255.255.0
aggregate-address 155.1.0.0 255.255.0.0 summary only
neighbour 54.1.1.254 distance-54
neighbor 54.1.1.254 dmzlink-bw
neighbour 155.1.67.7 distance-300
neighbour 155.1.146.1 distance-100
155.1.146.1 neighbor send-community times
No Auto-resume
Rack1R6 (config) #.
Rack1R6 (config) #do sh ip bgp neigh 155.1.146.1 opponents
Version of BGP table is 35, local router ID is 150.1.6.6
Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.
r SIDE-failure, stale S
Source codes: i - IGP, e - EGP,? -incomplete
Network Next Hop path metrics LocPrf weight
* > 28.119.16.0/24 54.1.1.254 0 54 I
* > 28.119.17.0/24 54.1.1.254 0 54 I
* > 112.0.0.0 54.1.1.254 0 0 54 50 60 I
* > 113.0.0.0 54.1.1.254 0 0 54 50 60 I
* > 114.0.0.0 54.1.1.254 0 0 54 I
* > 115.0.0.0 54.1.1.254 0 0 54 I
* > 116.0.0.0 54.1.1.254 0 0 54 I
* > 117.0.0.0 54.1.1.254 0 0 54 I
* > 118.0.0.0 54.1.1.254 0 0 54 I
* > 119.0.0.0 54.1.1.254 0 0 54 I
r > 155.1.0.0 0.0.0.0 32768 I
Rack1R6 (config) #do sh ip bgp
Version of BGP table is 35, local router ID is 150.1.6.6
Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.
r SIDE-failure, stale S
Source codes: i - IGP, e - EGP,? -incomplete
Network Next Hop path metrics LocPrf weight
* i28.119.16.0/24 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 54 i
* i28.119.17.0/24 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 54 i
* i112.0.0.0 204.12.1.254 0 100 0 54 50 60 I
* > 0 0 54 50 60 54.1.1.254 I
* i113.0.0.0 204.12.1.254 0 100 0 54 50 60 I
* > 0 0 54 50 60 54.1.1.254 I
* i114.0.0.0 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 0 54 i
* i115.0.0.0 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 0 54 i
* i116.0.0.0 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 0 54 i
* i117.0.0.0 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 0 54 i
* i118.0.0.0 204.12.1.254 0 100 0 54 I
Network Next Hop path metrics LocPrf weight
*> 54.1.1.254 0 0 54 i
* i119.0.0.0 204.12.1.254 0 100 0 54 I
*> 54.1.1.254 0 0 54 i
r i155.1.0.0 155.1.146.4 0 100 0 I
r> 0.0.0.0 32768 i
s > 155.1.146.0/24 0.0.0.0 32768 0 I
* > i205.90.31.0 155.1.13.3 0 100 0 200 254?
* 155.1.67.7 0 300 200 254?
* > i220.20.3.0 155.1.13.3 0 100 0 200 254?
* 155.1.67.7 0 300 200 254?
* > i222.22.2.0 155.1.13.3 0 100 0 200 254?
* 155.1.67.7 0 300 200 254?
Rack1R6 (config) #.
# now R4 configuration
Rack1R4 (config) #do sh run | dry BGP
router bgp 100
no synchronization
The log-neighbor BGP-changes
BGP dmzlink-bw
155.1.146.0 netmask 255.255.255.0
aggregate-address 155.1.0.0 255.255.0.0 summary only
neighbour 155.1.45.5 distance-200
155.1.45.5 route-neighbour card GAME-54 on
neighbour 155.1.146.1 distance-100
155.1.146.1 neighbor send-community times
neighbour 204.12.1.254 distance-54
neighbor 204.12.1.254 dmzlink-bw
No Auto-resume
Rack1R4 (config) #.
Rack1R4 (config) #do sh ip bgp Synt.
Local router BGP 150.1.4.4 identifier UNDER number 100
BGP table version is 18, table 18 main routing version
15 entries for network using 1980 bytes of memory
18 entries for path using 936 bytes of memory
9/7 BGP path/bestpath attribute entered using 1512 bytes of memory
3 entries for BGP AS-path ACCESS using 72 bytes of memory
1 entries PMO community, using 24 bytes of memory
0 cache entries of BGP route-map with 0 bytes of memory
0 cache entries of filter-list BGP using 0 bytes of memory
Bit entries in the cache field: 3 courses (up to 5) with 96 bytes of memory
BGP using 4620 total number of bytes of memory
Activity 102/87 BGP prefixes, 243/225, scan interval to 60 seconds
Neighbor MsgRcvd MsgSent V AS TblVer InQ OutQ Up/Down State/PfxRcd
155.1.45.5 4 200 8615 8640 18 0 0 07:38:02 3
155.1.146.1 4 100 8761 8668 18 0 0 00:14:34 3
204.12.1.254 4 54 8724 8595 18 0 0 07:38:02 10
Rack1R4 (config) #do sh ip bgp
BGP table version is 18, local router ID is 150.1.4.4
Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.
r SIDE-failure, stale S
Source codes: i - IGP, e - EGP,? -incomplete
Network Next Hop path metrics LocPrf weight
* > 28.119.16.0/24 204.12.1.254 0 0 54 I
* > 28.119.17.0/24 204.12.1.254 0 0 54 I
* > 112.0.0.0 204.12.1.254 0 54 50 60 I
* > 113.0.0.0 204.12.1.254 0 54 50 60 I
* > 114.0.0.0 204.12.1.254 0 54 I
* > 115.0.0.0 204.12.1.254 0 54 I
* > 116.0.0.0 204.12.1.254 0 54 I
* > 117.0.0.0 204.12.1.254 0 54 I
* > 118.0.0.0 204.12.1.254 0 54 I
* > 119.0.0.0 204.12.1.254 0 54 I
* > 155.1.0.0 0.0.0.0 32768 I
s > 155.1.146.0/24 0.0.0.0 32768 0 I
* i205.90.31.0 155.1.13.3 0 100 0 200 254?
*> 155.1.45.5 0 200 254 ?
* i220.20.3.0 155.1.13.3 0 100 0 200 254?
*> 155.1.45.5 0 200 254 ?
* i222.22.2.0 155.1.13.3 0 100 0 200 254?
Network Next Hop path metrics LocPrf weight
*> 155.1.45.5 0 200 254 ?
Rack1R4 (config) #do sh ip bgp neigh 155.1.146.1 opponents
Rack1R4 (config) #do sh ip bgp neigh 155.1.146.1 opponents
BGP table version is 18, local router ID is 150.1.4.4
Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.
r SIDE-failure, stale S
Source codes: i - IGP, e - EGP,? -incomplete
Network Next Hop path metrics LocPrf weight
* > 28.119.16.0/24 204.12.1.254 0 0 54 I
* > 28.119.17.0/24 204.12.1.254 0 0 54 I
* > 112.0.0.0 204.12.1.254 0 54 50 60 I
* > 113.0.0.0 204.12.1.254 0 54 50 60 I
* > 114.0.0.0 204.12.1.254 0 54 I
* > 115.0.0.0 204.12.1.254 0 54 I
* > 116.0.0.0 204.12.1.254 0 54 I
* > 117.0.0.0 204.12.1.254 0 54 I
* > 118.0.0.0 204.12.1.254 0 54 I
* > 119.0.0.0 204.12.1.254 0 54 I
* > 155.1.0.0 0.0.0.0 32768 I
* > 205.90.31.0 155.1.45.5 0 200 254?
* > 220.20.3.0 155.1.45.5 0 200 254?
* > 222.22.2.0 155.1.45.5 0 200 254?
Total number of prefixes 14
Rack1R4 (config) #.
# and where is the real problem, R1
Rack1R1(config-Router) #do sh ip bgp
Version of BGP table is 15, local router ID is 150.1.1.1
Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.
r SIDE-failure, stale S
Source codes: i - IGP, e - EGP,? -incomplete
Network Next Hop path metrics LocPrf weight
* i28.119.16.0/24 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i28.119.17.0/24 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i112.0.0.0 54.1.1.254 0 100 0 54 50 60 I
* > I 204.12.1.254 0 100 0 54 50 60 I
* i113.0.0.0 54.1.1.254 0 100 0 54 50 60 I
* > I 204.12.1.254 0 100 0 54 50 60 I
* i114.0.0.0 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i115.0.0.0 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i116.0.0.0 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i117.0.0.0 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i118.0.0.0 54.1.1.254 0 100 0 54 I
Network Next Hop path metrics LocPrf weight
* > I 204.12.1.254 0 100 0 54 I
* i119.0.0.0 54.1.1.254 0 100 0 54 I
* > I 204.12.1.254 0 100 0 54 I
* i155.1.0.0 155.1.146.6 0 100 0 I
* > I 155.1.146.4 0 100 0 I
* > 205.90.31.0 155.1.13.3 0 200 254?
* i 155.1.45.5 0 100 0 200 254?
* > 220.20.3.0 155.1.13.3 0 200 254?
* i 155.1.45.5 0 100 0 200 254?
* > 222.22.2.0 155.1.13.3 0 200 254?
* i 155.1.45.5 0 100 0 200 254?
Rack1R1 (config - Router) # do sh ip bgp 112.0.0.0
112.0.0.0/8, version 4 BGP routing table entry
Paths: (2 available, best #2, table by default-IP-Routing-Table)
MPIO: eBGP iBGP
Announced for the update-groups:
1 2
54 50 60, (from a customer-RR)
54.1.1.254 (metric 2560002816) of 155.1.146.6 (150.1.6.6)
Origin, IGP, 0, 100, valid, internal multipath localpref metric.
DMZ-Link Bw 250 KB
54 50 60, (from a customer-RR)
204.12.1.254 (metric 2560002816) of 155.1.146.4 (150.1.4.4)
Origin, IGP, metric 0, localpref 100, valid, internal, multipath, best
DMZ-Link Bw 12500 KB
Rack1R1(config-Router) #do sh ip route 112.0.0.0
Routing for 112.0.0.0/8 entry
Known through 'bgp 100', 200, 0 distance metric
54, internal type tag
Last update of 204.12.1.254 ago 00:15:30
Routing descriptor blocks:
204.12.1.254, 155.1.146.4, there is 00:15:30
Path metric is 0, number of shares of traffic 1
AS hop 3
Beacon road 54
* 54.1.1.254, 155.1.146.6, there is 00:15:30
Path metric is 0, number of shares of traffic 1
AS hop 3
Beacon road 54
Rack1R1 (config - Router) #.
as you can see, the BGP process in R1 receives the correct link DMZ bw but not indeed take...
can you please help me if I makeover anything in my setup?
Hello
Can you please make sure you have a value of bandwidth on ALL your BGP peering physical interfaces? And you can also include the running-config 'router bgp XXXX' out of R1 as you have not understood what we (others are). Just to make sure that you have "bgp dmzlink-bw' configured on all peerings and overall in the process - it will still show in the output of the same community if it does not work on it.
-
BlackBerry smartphones don't host Routing Table - no entries
Hello
I have a Blackbery Curve 8520. I have a problem with the connection to the mobile internet. When I entered the host Routing Table, it only shows me no entries. I registered several times but nothing happens. I have a gift of freedom of Vodafone afford data unlimited but I can't connect at all. Could someone help me? Thank youDo you have a data Plan BlackBerry enabled on your account with your carrier or mobile provider?
You have to, to get the push RIM email functions you are looking for, as well as services of BlackBerry data such as the Web browser, Facebook for BlackBerry, BlackBerry Messenger and much more.
Then call your carrier and you learn about to have added to your account BlackBerry data Plan.
Good luck.
-
[Solved] RV082 - SRP527W site-to-site VPN - routing table?
Hello
I am trying to create a VPN IPSEC link between 2 offices. The VPN connection is created, and I can connect but only one way.
Customers in the Office B seems to have a routing problem. Can you help me?
Details :
Office:
-Router SRP527W.
-Network client: 192.168.0.0 / 24
-Internal address: 192.168.0.254 / 24
B office:
-RV082 router (behind another router)
-Network client: 192.168.6.0 / 24
-Internal address: 192.168.6.253 / 24
-Internal address that goes to the Router 1: 192.168.5.253
internal address of the Router - 1: 192.168.5.254
Page layout:
Office---> SRP527W---> INTERNET<----- global="" router=""><------ rv082="">< office="">
192.168.0.254 192.168.5.254 5,253 6.254
Details VPN:
Office:
-remote type SUBNET = 192.168.6.0 group / 24
-local group = SUBNET 192.168.0.0/24
-Address ID = 82.127.XXX.XXX
B office:
-remote type = SUBNET 192.168.0.0/24 Group
-local group = SUBNET 192.168.6.0 / 24
-IP address = 192.168.5.253 (accessed from the Internet through the 1st router with the IP 37.1.XXX.XXX)
Facts:
A desktop, I can ping everything in 6.0 addresses.
Office B, I cannot ping anything in 0.0 subnet addresses. The router itself with the diagnostic page, works of ping 192.168.0.1? But no other ping. Curious...
The desktop computer B routing table shows the following:
Active routes:
Destination network mask network Adr. Gateway Adr. interface metric
0.0.0.0 0.0.0.0 192.168.6.253 192.168.6.10 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.6.0 255.255.255.0 192.168.6.10 192.168.6.10 10
192.168.6.10 255.255.255.255 127.0.0.1 127.0.0.1 10
192.168.6.255 255.255.255.255 192.168.6.10 192.168.6.10 10
224.0.0.0 240.0.0.0 192.168.6.10 192.168.6.10 10
255.255.255.255 255.255.255.255 192.168.6.10 192.168.6.10 1
255.255.255.255 255.255.255.255 192.168.6.10 3 1
255.255.255.255 255.255.255.255 192.168.6.10 1 40005
Default gateway: 192.168.6.253
===========================================================================
Persistent routes:
None
Tracert from computers to Office B shows that the packages have arrived at 192.168.6.253, and then it never achieved anything.
The problem is related to the architecture of Office B?
See the files attached to a layout of Office B and the routing of the router table to Office B.
Thank you.
Enable NAT - T on the RPS and configure the remote ID as 192.168.5.253 in the IKE policy.
Not sure about the RV and if supporting NAT - T. It can automatically detect the NAT - T, or need to be configured (in this case, you configure the local identification)
Andy.
-
BlackBerry smartphones not the host routing table entries
My blackberry storm2 shows no entries in the host routing table. I'm on a service plan that supports BIS everything was fine. My phone rebooted for no reason, and that's when the problem started
Help, please
Hello and welcome to the community!
I suggest the following, in order, even if they seem redundant to what you have already tried (steps 1 and 2, each should result in a message to your BB to come...) Please wait for this before moving on to the next step):
(1) registry HRT
- KB00510 How to register a BlackBerry smartphone with wireless network
- Please wait a 'registration' message reach your Messages application
(2) remove and return Service directories
- KB05000 Remove the maintenance book for the BlackBerry Internet Service email account in the BlackBerry smartphone
- If you do not have access CMIME, continue deleting
- KB02830 Send the directories for the BlackBerry Internet Service
- Please wait "the Activation' Messages, one per already configured e-mail account, arrive in your Messages. If you have not already configured email accounts, please wait 1 hour.
(3) restart to take batt
- Each time a random strange behavior or slow creeps, the first thing to do is a battery pop reboot. With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes. See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.
I hope that will move things again for you! If any stage does not properly complete, proceed to the subsequent steps will be useless... and you will need to contact your mobile provider for formal support. It's their network that your BB is unable to communicate with, after all.
Good luck!
-
WLC 2106 routing table do not fill
Hey guys, I hope you can help with this one.
I just tried to set up a WLC 2106 and everything seems OK however the routing table is not filled (even directly connected and default route). Currently, I have it plugged into a switch and an AP and they are all two visible in ARP and CDP, but I only ping is peripheral.
(Cisco Controller) > show the summary
Number of roads... 0
Destination Netmask Gateway network
------------------- ------------------- -------------------
(Cisco Controller) > show cdp neighbors detail
-------------------------
Device ID:-swt00.asggroup.com.au
Enter address (s): 10.33.17.62
Platform: cisco WS-C3750G-48TS, capacity: Switch IGMP router
Interface: Fastethernet0/0/1, ID of Port (outgoing port): GigabitEthernet1/0/48
Hold time: 174 s
Version:
Cisco IOS software, software C3750 (C3750-IPSERVICESK9-M), Version 12.2 SEE2 (25), RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc., Compiled Saturday 28 July 06 12:55 by yenanh
version of the proclamation: 1
-------------------------
Device ID: AP1cdf.0f95.732c
Enter address (s): 10.33.17.10
Platform: cisco AIR-LAP1142N-N-K9, capacity: Trans-pont
Interface: Fastethernet0/0/7, ID of Port (outgoing port): GigabitEthernet0
Hold time: 155 s
Version:
Cisco IOS software, C1140 Software (C1140-K9W8-M), Version 12.4 (21 a) JHB1 - VERSION of the SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2010 by Cisco Systems, Inc., Compiled Thursday, Aug 11, 10 at 15:45 by prod_rel_team
-Other - or ITU (q)
version of the proclamation: 1
Configuration of the interface
Name of the interface... ap-Manager
MAC address... 58.8 d: 09:93:f1:c0
IP Address....................................... 10.33.17.2
IP Netmask....................................... 255.255.255.192
IP Gateway....................................... 10.33.17.62
State IP NAT outside... People with disabilities
External IP NAT... 0.0.0.0
VLAN............................................. 17
Port of physics... 1
Primary DHCP server... 10.33.17.1
Secondary DHCP server... Not configured
Option DHCP 82... People with disabilities
ACL.............................................. Not configured
AP Manager....................................... Yes
Comments interface... NO.
... Management interface
MAC address... 58.8 d: 09:93:f1:c0
IP Address....................................... 10.33.17.1
IP Netmask....................................... 255.255.255.192
IP Gateway....................................... 10.33.17.62
State IP NAT outside... People with disabilities
External IP NAT... 0.0.0.0
VLAN............................................. 17
Quarantine-vlan... 0
Port of physics... 1
Primary DHCP server... 10.33.17.1
Secondary DHCP server... Not configured
Option DHCP 82... People with disabilities
ACL.............................................. Not configured
AP Manager....................................... NO.
Comments interface... NO.
Any help would be greatly appreciatedMarkHello
Removes the brand management and interface of the AP on the WLC Manager and put the management and the Manager of the Ap in the vlan Switchports native...
example of...
the command is...
WLC > config interface management vlan 0
WLC > config interface vlan ap-Manager 0
On the switch...
switchport mode trunk
switchport trunk dot1q encap
switchport trunk vlan native 17
end
I assumed the management and Manager of the AP are in vlan 17. make the corresponding changes if not 17.
Let me know if we can t oping after making the above changes...
Let me know if that answers your question...
Concerning
Surendra
====
Please do not forget to note positions that answered your question and mark as answer or was useful -
map does not show the routes and directions
This feature is not yet supported in India.
http://www.Apple.com/in/iOS/feature-availability/#maps-directions
In addition, your phone may be overheating for a number of reasons. The most common of which is low service area.
Your attributes from battery to the majority of the production of heat, then adjust settings to put less load on the farm in general will help some.
-
Too many routing table entries
I just got a new Airport Extreme, and that's what my routing table. I connect through a Modem of Surfboard Arris model SB6141, it seems normal?
Routing tables
Internet:
Destination Gateway Flags Refs use Netif expire
default 192.168.1.1 UGSc 49 228 en0
127 UCS 1 0 lo0 localhost
localhost localhost UH 5 9953 lo0
169.254 link #4 UCS 2 0 en0
169.254.28.172 link #4 UHLSW 1 9 en0
192.168.1 link #4 UCS 254 0 en0
192.168.1.1/32 link #4 UCS 3 0 en0
192.168.1.1 d0:3:4 b: d3:94:b5 UHLWIir 184 1177 en0 1045
192.168.1.2 dc:2 b: 2A: 9f:48:e0 UHLWIi 1 127 en0 1183
192.168.1.3 link #4 UHLWIi 1 82 en0
192.168.1.4 link #4 UHLWIi 1 38 en0
192.168.1.5/32 link #4 UCS 2 0 en0
192.168.1.5 a8:66:7f:20:b1:f1 UHLWIi 1 226 lo0
192.168.1.6 link #4 UHLWIi 1 7 en0
192.168.1.7 link #4 UHLWIi 1 7 en0
192.168.1.8 link #4 UHLWIi 1 7 en0
192.168.1.9 link #4 UHLWIi 1 6 en0
192.168.1.10 link #4 UHLWIi 1 6 en0
192.168.1.11 link #4 UHLWIi 1 6 en0
192.168.1.12 link #4 UHLWIi 1 6 en0
192.168.1.13 link #4 UHLWIi 1 6 en0
192.168.1.14 link #4 UHLWIi 1 6 en0
192.168.1.15 link #4 UHLWIi 1 6 en0
192.168.1.16 link #4 UHLWIi 1 6 en0
192.168.1.17 link #4 UHLWIi 1 6 en0
192.168.1.18 link #4 UHLWIi 1 6 en0
192.168.1.19 link #4 UHLWIi 1 6 en0
192.168.1.20 link #4 UHLWIi 1 6 en0
192.168.1.21 link #4 UHLWIi 1 6 en0
192.168.1.22 link #4 UHLWIi 1 6 en0
192.168.1.23 link #4 UHLWIi 1 6 en0
192.168.1.24 link #4 UHLWIi 1 6 en0
192.168.1.25 link #4 UHLWIi 1 6 en0
192.168.1.26 link #4 UHLWIi 1 7 en0
192.168.1.27 link #4 UHLWIi 1 7 en0
192.168.1.28 link #4 UHLWIi 1 7 en0
192.168.1.29 link #4 UHLWIi 1 7 en0
192.168.1.30 link #4 UHLWIi 1 7 en0
192.168.1.31 link #4 UHLWIi 1 7 en0
192.168.1.32 link #4 UHLWIi 1 7 en0
192.168.1.33 link #4 UHLWIi 1 7 en0
192.168.1.34 link #4 UHLWIi 1 6 en0
192.168.1.35 link #4 UHLWIi 1 6 en0
192.168.1.36 link #4 UHLWIi 1 6 en0
192.168.1.37 link #4 UHLWIi 1 6 en0
192.168.1.38 link #4 UHLWIi 1 6 en0
192.168.1.39 link #4 UHLWIi 1 6 en0
192.168.1.40 link #4 UHLWIi 1 6 en0
192.168.1.41 link #4 UHLWIi 1 6 en0
192.168.1.42 link #4 UHLWIi 1 6 en0
192.168.1.43 link #4 UHLWIi 1 6 en0
192.168.1.44 link #4 UHLWIi 1 6 en0
192.168.1.45 link #4 UHLWIi 1 6 en0
192.168.1.46 link #4 UHLWIi 1 6 en0
192.168.1.47 link #4 UHLWIi 1 6 en0
192.168.1.48 link #4 UHLWIi 1 6 en0
192.168.1.49 link #4 UHLWIi 1 6 en0
192.168.1.50 link #4 UHLWIi 1 6 en0
192.168.1.51 link #4 UHLWIi 1 6 en0
192.168.1.52 link #4 UHLWIi 1 7 en0
192.168.1.53 link #4 UHLWIi 1 7 en0
192.168.1.54 link #4 UHLWIi 1 7 en0
192.168.1.55 link #4 UHLWIi 1 7 en0
192.168.1.56 link #4 UHLWIi 1 7 en0
192.168.1.57 link #4 UHLWIi 1 7 en0
192.168.1.58 link #4 UHLWIi 1 7 en0
192.168.1.59 link #4 UHLWIi 1 7 en0
192.168.1.60 link #4 UHLWIi 1 6 en0
192.168.1.61 link #4 UHLWIi 1 6 en0
192.168.1.62 link #4 UHLWIi 1 6 en0
192.168.1.63 link #4 UHLWIi 1 6 en0
192.168.1.64 link #4 UHLWIi 1 6 en0
192.168.1.65 link #4 UHLWIi 1 6 en0
192.168.1.66 link #4 UHLWIi 1 6 en0
192.168.1.67 link #4 UHLWIi 1 6 en0
192.168.1.68 link #4 UHLWIi 1 6 en0
192.168.1.69 link #4 UHLWIi 1 6 en0
192.168.1.70 link #4 UHLWIi 1 6 en0
192.168.1.71 link #4 UHLWIi 1 6 en0
192.168.1.72 link #4 UHLWIi 1 6 en0
192.168.1.73 link #4 UHLWIi 1 6 en0
192.168.1.74 link #4 UHLWIi 1 6 en0
192.168.1.75 link #4 UHLWIi 1 6 en0
192.168.1.76 link #4 UHLWIi 1 6 en0
192.168.1.77 link #4 UHLWIi 1 6 en0
192.168.1.78 link #4 UHLWIi 1 7 en0
192.168.1.79 link #4 UHLWIi 1 7 en0
192.168.1.80 link #4 UHLWIi 1 7 en0
192.168.1.81 link #4 UHLWIi 1 7 en0
192.168.1.82 link #4 UHLWIi 1 7 en0
192.168.1.83 link #4 UHLWIi 1 7 en0
192.168.1.84 link #4 UHLWIi 1 7 en0
192.168.1.85 link #4 UHLWIi 1 7 en0
192.168.1.86 link #4 UHLWIi 1 6 en0
192.168.1.87 link #4 UHLWIi 1 6 en0
192.168.1.88 link #4 UHLWIi 1 6 en0
192.168.1.89 link #4 UHLWIi 1 6 en0
192.168.1.90 link #4 UHLWIi 1 6 en0
192.168.1.91 link #4 UHLWIi 1 6 en0
192.168.1.92 link #4 UHLWIi 1 6 en0
192.168.1.93 link #4 UHLWIi 1 6 en0
192.168.1.94 link #4 UHLWIi 1 6 en0
192.168.1.95 link #4 UHLWIi 1 6 en0
192.168.1.96 link #4 UHLWIi 1 6 en0
192.168.1.97 link #4 UHLWIi 1 6 en0
192.168.1.98 link #4 UHLWIi 1 6 en0
192.168.1.99 link #4 UHLWIi 1 6 en0
192.168.1.100 link #4 UHLWIi 1 6 en0
192.168.1.101 link #4 UHLWIi 1 6 en0
192.168.1.102 link #4 UHLWIi 1 6 en0
192.168.1.103 link #4 UHLWIi 1 6 en0
192.168.1.104 link #4 UHLWIi 1 7 en0
192.168.1.105 link #4 UHLWIi 1 7 en0
192.168.1.106 link #4 UHLWIi 1 7 en0
192.168.1.107 link #4 UHLWIi 1 7 en0
192.168.1.108 link #4 UHLWIi 1 7 en0
192.168.1.109 link #4 UHLWIi 1 7 en0
192.168.1.110 link #4 UHLWIi 1 7 en0
192.168.1.111 link #4 UHLWIi 1 7 en0
192.168.1.112 link #4 UHLWIi 1 6 en0
192.168.1.113 link #4 UHLWIi 1 6 en0
192.168.1.114 link #4 UHLWIi 1 6 en0
192.168.1.115 link #4 UHLWIi 1 6 en0
192.168.1.116 link #4 UHLWIi 1 6 en0
192.168.1.117 link #4 UHLWIi 1 6 en0
192.168.1.118 link #4 UHLWIi 1 6 en0
192.168.1.119 link #4 UHLWIi 1 6 en0
192.168.1.120 link #4 UHLWIi 1 6 en0
192.168.1.121 link #4 UHLWIi 1 6 en0
192.168.1.122 link #4 UHLWIi 1 6 en0
192.168.1.123 link #4 UHLWIi 1 6 en0
192.168.1.124 link #4 UHLWIi 1 6 en0
192.168.1.125 link #4 UHLWIi 1 6 en0
192.168.1.126 link #4 UHLWIi 1 6 en0
192.168.1.127 link #4 UHLWIi 1 6 en0
192.168.1.128 link #4 UHLWIi 1 6 en0
192.168.1.129 link #4 UHLWIi 1 6 en0
192.168.1.130 link #4 UHLWIi 1 7 en0
192.168.1.131 link #4 UHLWIi 1 7 en0
192.168.1.132 link #4 UHLWIi 1 7 en0
192.168.1.133 link #4 UHLWIi 1 7 en0
192.168.1.134 link #4 UHLWIi 1 7 en0
192.168.1.135 link #4 UHLWIi 1 7 en0
192.168.1.136 link #4 UHLWIi 1 7 en0
192.168.1.137 link #4 UHLWIi 1 7 en0
192.168.1.138 link #4 UHLWIi 1 6 en0
192.168.1.139 link #4 UHLWIi 1 6 en0
192.168.1.140 link #4 UHLWIi 1 6 en0
192.168.1.141 link #4 UHLWIi 1 6 en0
192.168.1.142 link #4 UHLWIi 1 6 en0
192.168.1.143 link #4 UHLWIi 1 6 en0
192.168.1.144 link #4 UHLWIi 1 6 en0
192.168.1.145 link #4 UHLWIi 1 6 en0
192.168.1.146 link #4 UHLWIi 1 6 en0
192.168.1.147 link #4 UHLWIi 1 6 en0
192.168.1.148 link #4 UHLWIi 1 6 en0
192.168.1.149 link #4 UHLWIi 1 6 en0
192.168.1.150 link #4 UHLWIi 1 6 en0
192.168.1.151 link #4 UHLWIi 1 6 en0
192.168.1.152 link #4 UHLWIi 1 6 en0
192.168.1.153 link #4 UHLWIi 1 6 en0
192.168.1.154 link #4 UHLWIi 1 6 en0
192.168.1.155 link #4 UHLWIi 1 6 en0
192.168.1.156 link #4 UHLWIi 1 7 en0
192.168.1.157 link #4 UHLWIi 1 7 en0
192.168.1.158 link #4 UHLWIi 1 7 en0
192.168.1.159 link #4 UHLWIi 1 7 en0
192.168.1.160 link #4 UHLWIi 1 7 en0
192.168.1.161 link #4 UHLWIi 1 7 en0
192.168.1.162 link #4 UHLWIi 1 7 en0
192.168.1.163 link #4 UHLWIi 1 7 en0
192.168.1.164 link #4 UHLWIi 1 6 en0
192.168.1.165 link #4 UHLWIi 1 6 en0
192.168.1.166 link #4 UHLWIi 1 6 en0
192.168.1.167 link #4 UHLWIi 1 6 en0
192.168.1.168 link #4 UHLWIi 1 6 en0
192.168.1.169 link #4 UHLWIi 1 6 en0
192.168.1.170 link #4 UHLWIi 1 6 en0
192.168.1.171 link #4 UHLWIi 1 6 en0
192.168.1.172 link #4 UHLWIi 1 6 en0
192.168.1.173 link #4 UHLWIi 1 6 en0
192.168.1.174 link #4 UHLWIi 1 6 en0
192.168.1.175 link #4 UHLWIi 1 6 en0
192.168.1.176 link #4 UHLWIi 1 6 en0
192.168.1.177 link #4 UHLWIi 1 6 en0
192.168.1.178 link #4 UHLWIi 1 6 en0
192.168.1.179 link #4 UHLWIi 1 6 en0
192.168.1.180 link #4 UHLWIi 1 6 en0
192.168.1.181 link #4 UHLWIi 1 6 en0
192.168.1.182 link #4 UHLWIi 1 7 en0
192.168.1.183 link #4 UHLWIi 1 7 en0
192.168.1.184 link #4 UHLWIi 1 7 en0
192.168.1.185 link #4 UHLWIi 1 7 en0
192.168.1.186 link #4 UHLWIi 1 7 en0
192.168.1.187 link #4 UHLWIi 1 7 en0
192.168.1.188 link #4 UHLWIi 1 7 en0
192.168.1.189 link #4 UHLWIi 1 7 en0
192.168.1.190 link #4 UHLWIi 1 6 en0
192.168.1.191 link #4 UHLWIi 1 6 en0
192.168.1.192 link #4 UHLWIi 1 6 en0
192.168.1.193 link #4 UHLWIi 1 6 en0
192.168.1.194 link #4 UHLWIi 1 6 en0
192.168.1.195 link #4 UHLWIi 1 6 en0
192.168.1.196 link #4 UHLWIi 1 6 en0
192.168.1.197 link #4 UHLWIi 1 6 en0
192.168.1.198 link #4 UHLWIi 1 6 en0
192.168.1.199 link #4 UHLWIi 1 6 en0
192.168.1.200 link #4 UHLWIi 1 6 en0
192.168.1.201 link #4 UHLWIi 1 6 en0
192.168.1.202 link #4 UHLWIi 1 6 en0
192.168.1.203 link #4 UHLWIi 1 6 en0
192.168.1.204 link #4 UHLWIi 1 6 en0
192.168.1.205 link #4 UHLWIi 1 6 en0
192.168.1.206 link #4 UHLWIi 1 6 en0
192.168.1.207 link #4 UHLWIi 1 6 en0
192.168.1.208 link #4 UHLWIi 1 7 en0
192.168.1.209 link #4 UHLWIi 1 7 en0
192.168.1.210 link #4 UHLWIi 1 7 en0
192.168.1.211 link #4 UHLWIi 1 7 en0
192.168.1.212 link #4 UHLWIi 1 7 en0
192.168.1.213 link #4 UHLWIi 1 7 en0
192.168.1.214 link #4 UHLWIi 1 7 en0
192.168.1.215 link #4 UHLWIi 1 7 en0
192.168.1.216 link #4 UHLWIi 1 6 en0
192.168.1.217 link #4 UHLWIi 1 6 en0
192.168.1.218 link #4 UHLWIi 1 6 en0
192.168.1.219 link #4 UHLWIi 1 6 en0
192.168.1.220 link #4 UHLWIi 1 6 en0
192.168.1.221 link #4 UHLWIi 1 6 en0
192.168.1.222 link #4 UHLWIi 1 6 en0
192.168.1.223 link #4 UHLWIi 1 6 en0
192.168.1.224 link #4 UHLWIi 1 6 en0
192.168.1.225 link #4 UHLWIi 1 6 en0
192.168.1.226 link #4 UHLWIi 1 6 en0
192.168.1.227 link #4 UHLWIi 1 6 en0
192.168.1.228 link #4 UHLWIi 1 6 en0
192.168.1.229 link #4 UHLWIi 1 6 en0
192.168.1.230 link #4 UHLWIi 1 6 en0
192.168.1.231 link #4 UHLWIi 1 6 en0
192.168.1.232 link #4 UHLWIi 1 6 en0
192.168.1.233 link #4 UHLWIi 1 6 en0
192.168.1.234 link #4 UHLWIi 1 7 en0
192.168.1.235 link #4 UHLWIi 1 7 en0
192.168.1.236 link #4 UHLWIi 1 7 en0
192.168.1.237 link #4 UHLWIi 1 7 en0
192.168.1.238 link #4 UHLWIi 1 7 en0
192.168.1.239 link #4 UHLWIi 1 7 en0
192.168.1.240 link #4 UHLWIi 1 7 en0
192.168.1.241 link #4 UHLWIi 1 7 en0
192.168.1.242 link #4 UHLWIi 1 6 en0
192.168.1.243 link #4 UHLWIi 1 6 en0
192.168.1.244 link #4 UHLWIi 1 6 en0
192.168.1.245 link #4 UHLWIi 1 6 en0
192.168.1.246 link #4 UHLWIi 1 6 en0
192.168.1.247 link #4 UHLWIi 1 6 en0
192.168.1.248 link #4 UHLWIi 1 6 en0
192.168.1.249 link #4 UHLWIi 1 6 en0
192.168.1.250 link #4 UHLWIi 1 6 en0
192.168.1.251 link #4 UHLWIi 1 6 en0
192.168.1.252 link #4 UHLWIi 1 6 en0
192.168.1.253 link #4 UHLWIi 1 6 en0
192.168.1.254 link #4 UHLWIi 1 6 en0
192.168.1.255 link UHLWbI 1 3 #4 en0
255.255.255.255/32 link #4 UCS 1 0 en0
Internet6:
Destination Gateway Flags Netif expire
UHL lo0 localhost localhost
fd17:8CB9:9 c 03:76 d fe80::dd4a:74ce:a5 Uc utun0
fd17:8CB9:9 c 03:76 d link #8 UHL lo0
FE80: % lo0 fe80::1% lo0 UcI lo0
FE80::1% lo0 link #1 UHLI lo0
FE80: % link #4 UCI en0 en0
Gold - macbook.local a8:66:7f:20:b1:f1 UHLI lo0
FE80: % awdl0 link #6 UCI awdl0
Gold - macbook.local 2e:70:5 has: 3e:71:f9 UHLI lo0
FE80: % utun0 fe80::dd4a:74ce:a5 utun0 of the UcI
FE80::dd4a:74ce:A5 link #8 UHLI lo0
FF01: % lo0 localhost UmCI lo0
FF01: % link #4 UmCI en0 en0
FF01: % awdl0 link #6 awdl0 UmCI
FF01: % utun0 fe80::dd4a:74ce:a5 utun0 UmCI
FF02: % lo0 localhost UmCI lo0
FF02: % link #4 UmCI en0 en0
FF02: % awdl0 link #6 awdl0 UmCI
FF02: % utun0 fe80::dd4a:74ce:a5 utun0 UmCI
Wow... you could just discovered what goes wrong.
SB6141 has a bug with airports... it does simply not very well...
There are several long posts...
https://discussions.Apple.com/message/22545346#22545346
https://discussions.Apple.com/thread/5048548
The most common recommended fix is to replace the modem by a model Zoom cable modem or the airport as the router.
Intermittently, Time Capsule does not connect to the cable Modem
What I want to know... How did this routing table...?
I presume that is netstat from your computer?
-
WSN Routing Tables and better path decisions
Hello
My team has placed a total of 10 knots in an industrial environment of factory. Nine are defined as routers, and there is only one end node. The gateway is a little in the center of this area, and there is no node failed. The coverage area is four floors with approximately 63000 square feet of floor area per level. I'm having a problem with a section of the path used to reach the end node: a quality signal between the 3rd and 4th routers gateway has been ignored in favor of a lower quality signal. If I take this 4th router and move it very closely the 3rd router and do a reset it will pick up the 3rd router signal and remain at about 60% intensity of the signal for several minutes. However, this 4th router will soon fall sharply to about 20% intensity (much less that NEITHER recommended by 30%) of the signal. The network is to decide than 3 jumps of signal is relatively good is worse than a jump involving a bad signal? Also, is there a way to read what are routing tables to determine if it is indeed the case?
Thank you!
Garrett
We suggest you use the least necessary routers for your background. Routers add the chance for the performance of the network has declined due to uninteded jump. Then, even when food is available, the default choice for the nodes must be nodes except routers are needed.
-
Cannot add a permanent route to the routing table.
Hello world
I tried to add a routing table that for some reason I can't do a ping on the Internet of some windows xp machines and I was adding "see Pei add 0.0.0.0 mask 0.0.0.0" and after you type this command, I was able to do a ping on and everything was going well until I rebooted. "." Whenever I reboot I am unable to ping but if I add "PEI route add 0.0.0.0 mask 0.0.0.0 it works again." It print my route continued under the road, but it doesn't seem to work when I reboot. Any help would be greatly appreciated.
Persistent routes:
Network gateway address mask network address metric
0.0.0.0 0.0.0.01 Any help would be greatly appreciated.
MichaelOriginal title: Windows XP adding a road permanent in the Routing Table (persistent route)
Hi Michael Rodrigues of La Mancha,
I wish you post your question in the TechNet Forums because it caters to an audience of it professionals.
Check out the link-
Hope this helps!
-
Windows xp routing table problem
I'm having a problem with windows routing tables on the pc at my workplace.
These computers are running windows xp sp3 and the problem occurs when I change the default gatewaythe PCs are on subnet 10.181.1.0/24 with d/g 10.181.1.11.
with this configuration, the routing on each pc table works as expected [for example, it stores a
Directions to its own subnet [10.181.1.0/24] but no way to other subnets [for example, it will not store
a road to 10.180.1.0/24, it will simply send this default network traffic
gateway].However, due to a re-design network, I need to change the default gateway for this lan
to 10.181.1.254. When I do cela something strange happens. the windows routing table on
each pc begins to store routes to the entire 10.0.0.0/8 network, even if the current
config on the pc is still a 24 network [for example, 10.181.1.21/24, d/g 10.181.1.254].
its as if when I change default gateway from the computer, windows, pleasures of the routing table of the
10.181.1.0/24 subnet as if it were a network 10.0.0.0/8 classful.While, right? I can still connect to other networks, the pc is just using a route
stored in its routing table local instead of sending traffic to its default gateway.
The problem is that we have a 10.181.1.12 default backup gateway that we switch to
If the primary gateway goes down. When we test failover to 10.181.1.12 pcs are always
Send non-local traffic to 10.181.1.11 [because they still have these routes stored locally in their]
Windows routing tables]. I want to send traffic to 10.181.1.254 [switch a core of layer 3, which then]
two lanes of traffic to 10.181.1.11 or. [12]I tried to change the default gateway to a range of ip addresses and the same problem occurs every time.
I rebooted each pc after having changed its d/g and the problem remains the same. I tried
delete all the information off the power the pc ip address, then re-enter with the new d/g, then restart
the pc but the problem remains the same.so, to summarize, when I change the d/g from any pc on the 10.181.1.0/24 subnet, computers table routing begins to store routes
in its local routing table to the classful, instead of just the classless 10.181.1.0/24 network 10.0.0.0/8 network.Has anyone encountered this before?
Hi biglouie2010,
Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows XP forum.
http://social.technet.Microsoft.com/forums/en/itproxpsp/threads
-
For three buildings with VPN routing tables
Can someone tell me how to configure routing for the following tables
I have three location. All three have a static public IP address
I need to have a VPN to each location at each location
A = 192.168.0.x
B = 192.168.1.x
C = 192.168.2.x
There are virtual private networks
A to B and a-C
B to A and B to C
C to A and C of the B
So what I need to know, is what are the internal traffic routing tables remains in the VPN and external traffic is routed on the local connection. I don't want a situation where site A sends internet traffic on to B and then to the world.
Thanks for the help
Basically, the IP address assigned on the security group Local and remote security group who are the only traffic that stays on the VPN.
-
BlackBerry Smartphones host Routing Table vacuum
My blackberry 9930 fone and all of a sudden last morning work was he had no ENCORE and there is no message in the host Routing Table, Ive sent messages that are not delivered and did a hard reset but nothing happens. The service provider says they can't pick up anything.
After you remove the service book, performing the hard reset by pulling your battery while your BlackBerry is on and reinsert again. Now try to register to the THS. Thank you.
God luck!
-
Loopback address VRF who flees to the global routing table
Hello
I have a router and you have set up several VRF. I was also able to run routes between the global routing table and one of the VRF (VRF data) with success.
Now, I have not been able to flee the VRF (1.1.1.1) data loopback address in the global routing table, so I can ping to the VRF the global routing table loopback address.
I also read this article:
http://www.Cisco.com/en/us/Tech/tk436/tk832/technologies_configuration_example09186a0080231a3e.shtml
Does anyone know this before?
Joined the config
Thank you
Reza
If select VRF is not supported, you can create a false road map and apply it to the loopback interface:
FAKE route map
vrf adjustment data
!
int loopback 0
FAKE IP policy-map of route
receive data IP vrf
!
HTH
Laurent.
Maybe you are looking for
-
It seems that Lenovo will introduce an application dedicated to the music of Lenovo in L Android, judging by the photos of 2015 MWC. Or is this already available in Chinese Version music app?
-
Convert number in reverse byte array?
How convert a value, said 10,000, in a table of 4 bytes and then reverse the byte order? Is there a function for this or? I can do it easily in LabVIEW, but I wonder if it's possible in TestStand. Thank you!
-
Provide a path to start (record) in a file dialog box
Is it possible to have a dialog file into a specific folder, without using the dialog file express VI? (I would also like to use an exec system). Thank you.
-
After that installation of windows live my computer slowed down really bad
After I installed windows live my computer at startup slowed down really bad and it is very slow, whenever I click on to go to other applications. are there Add-ons I can delete to speed up my laptop?
-
my laptop does not recognize my blackberry 8520 so I can't upload photos from phone
I connect my backberry 8520 to my laptop but it is not recognized as a storage of mass so down, I can not load my oss phone photos have been in full view of web backberry and re of the device, but this has not cured the problem they recommend to ask