Siri speaks only when it's plugged in?

Similar Questions

• Freezing up ONLY when it is PLUGGED in, DO NOT when executing a battery

  I'm having a problem with my computer toshiba laptop.  When I plug it and use it, it freezes. After many experiments, I discovered that when I leave it unplugged and run it just on the battery, it does not freeze upwards.  Help.  This is crazy.  What would cause such a thing.  I tried other points of sale, I tried to use the power strips.  It freezes only when it is plugged.

  Hi zianez,

  1. did you of recent changes on the computer?

  2. you receive an error message?

  3. do you have other external devices connected to the computer?

  Method 1

  I suggest that you reset the parameters of power plan on the laptop to default settings, then check if it works.

  (a) open the power supply Options by clicking the Start button, click Control Panel, clicking system and Maintenance, and then clicking Power Options.

  (b) according to the plan that you want to change, click change plan settings.

  (c) now, click change advanced power settings

  (d) click on restore defaults for this plan.

  (e) click applyand OK

   

  Check if the problem persists.

  Method 2

  If the previous step fails then I suggest that you check in the event viewer to find out the cause of the issue and after return with details.

  What are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Use Windows 7 CPU to 100% only when it is plugged

  I post this topic only because my problem is quiet unusual. I found hundreds of topics related to 100% CPU usage in Windows 7, but none of them was related to this over-consumption of the processor during the charging of the battery. There is also a situation that 100% of CPU usage occurs while working on the battery, but my case is completely the opposite.

  Windows 7 x 64 prof. system goes to 100% CPU use occasionally and it becomes impossible to work. then all of a sudden, the problem goes away and everything works right. After a few days of work without problem the problem returns and so on. I did the fresh install several times and the problem appeared immediately after the installation of the system every time. Finally, I discovered, that it lasts only when the charger is plugged in when you are working on the battery, everything works correctly. pluggng immediately after the CPU reaches 100% usage and so on.

  laptop HP Compaq 6710 b, Windows 7 x 64-teacher system.

  Help!

  Hello once again, Andre. Thank you for helping me. I tried to find such a framework (high precision event Timer) in my BIOS, but I did not: it seems to be fixed on my laptop. However, I found it in my Windows Device Manager and I have disabled HPET here, but it did not help in any case - there is no change in the use of the CPU (always 100%).

  BUT - I found an effective solution on my own! The thing was very simple - it was the fault of my power cord to the AC adapter / CC. I tried my colleague adapter and CPU usage dropped sharply to 5-10% on idle. Then I plugged my power adapter - use has exploded to 100%, and again, I used my colleague adapter - use declined.

  THE REASON FOR THE HIGH IN MY CASE CPU USAGE WAS DEFECTIVE AC ADAPTER

  It was a big surprise for me, because the problem occurred only from time to time. Apart from this, the laptop work properly. I tried hundreds of things, including the reinstallation of the system 3 times, change a hard drive (which seemed to make some strange sounds), my memory test, install the latest drivers from HP, change settings loading, etc. Only after buying a new battery (the old one was not operation at all) I noticed that the problem goes away after unplugging the AC adapter.

  I lost a lot of time trying to solve this problem and it was very frustrating, I also found that a lot of people have similar problems, so if you, dear reader, have 100% CPU use problem, unplugg your power adapter first know, that it's abandoned.

• Yoga 2 Pro - touchscreen shows quickly touches and is unusable ONLY when it is plugged

  When it's on battery, everything works great, no problems whatsoever.

  When it is plugged in, if I touch anywhere on any screen (lock desktop screen, any application etc.) I see the little white 'ghost' touch where my finger touches but then she does like 1000 times randomly in a vertical straight line hence my finger is. It is therefore impossible to log on using the image blocking feature.

  The keyboard and the touchpad both work when it's plugged in, but not the touch SCREEN.

  I wonder if perhaps you charger is a failure? It may be your charge voltage is not properly regulated or there is noise coming through the wall socket. I have seen problems like this on the phones with the charger plugged. Have you tried to connect the different wall outlets? You have access to another charger?

• envy touchsmart 15: speaker play when earphones are plugged

  Everything worked fine 2 days ago and then for some reason when I plug my headphones still sound speakers (as well as headphones)

  I have audio beats and I tried to turn off multi-streaming

  I can't put my headset as default player (I have before) speakers and headphones run through speakers/hp and before they were separated

  I uninstalled and reinstalled the sound drivers

  I also uninstalled the drivers and let windows find the driver when it starts

  Ive scanned the driver and changed to windows default driver

  its really annoying me now because I can't seem to find a way to fix it!

  Thanks in advance for your help

  Hi @cieran,

  Please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

• Wireless printer prints only when it is plugged in power cord.

  Original title: printer

  I have a wireless printer and was working fine and then stopped printing, it will print only with the USB cord plugged. How can I make work with the USB cord.

  Hello

  What printer you are using?  What is you receive the exact error message?
  As many printers have specific installation instructions, I know that my HP needed me for not connect it first, and then click Print network opposed to USB settings then plugged into the USB port for installation and then just unplug the USB and WiFi, printing, once all installed and tested WiFi printing you can also print via USB , for me I could anyway.

  Just uninstall the driver and software and all re - install again.

  With printer (get the USB cable for the moment)

  To try this click Start > devices and printers > add a printer > add a network, wireless or Bluetooth printer > it will search a little, but I hope that your printer will display in the main window, if it is to highlight and click Next and follow the prompts to install the driver.

  You can check these sites

  http://www.printerhacks.com/How-do-i-make-my-printer-wireless/

  http://www.labnol.org/gadgets/make-wired-printer-wireless/12639/

• Phone to download a lot of data via WiFi only when the charger is plugged - iPhone iOS 9.3.1 6s

  Hello

  Just today, I noticed that my iPhone 6s was download continuously at the speed of the network via WiFi only when is plugged in the wall charger or the USB loader on the computer. As soon as I stop charging the phone, the download stops. I have no idea what download and I'm a little frustrated because my connection high speed/wireless home is capped.

  Sync to iTunes on WiFi and iCloud backups are disabled. I had subscribed to 9.3.2 iOS beta on the registration by registering with my Apple ID last week, but I haven't added the certificate so that it can download OTA or via iTunes. I have no update available on my Apple store as well.

  I noticed the slowdown on my cause of internet connection of desktop computers that my phone of summer download something on wifi while he is in charge and I also saw the use of the network by using "System Monitor" app on the App store.

  Kindly help me to solve this problem.

  Thank you

  I did a factory reset on by phone by "Erase all content and data" and chose to set up as a "new iPhone" after reset done. There are now only apple applications on the phone, I connected to wifi with the charger plugged and the problem persists. I wonder if it was to be an apple iOS update, I am on iOS 9.3.1 and 9.3.2 is still in beta, I'm not sure if there is an apple update going on in the background.

  Kindly help.

• Y410P Nvidia GPU works only when plugged in?

  Hi all

  I know that this is a frequently asked question, and I also knew that the Nvidia GPU raised only when an application heavy 3D graphics is charged.

  This is the case. But I don't get a bad 3D rating (1 star or higher) during the game.

  I have configured the program updated Nvidia 3D well on a level of high performance battery. The notification bar of Nvidia is also show that the game is loaded using the Nvidia GPU.

  On the other hand, when the laptop is plugged in, I get a better mark 3D on the same game. How is that possible?

  It is not comfortable, due to the fact that I need to plug the laptop when I want to play the game to get the best performance.

  All solutions? Thanks in advance.

  Regardless of the number of parameters of high performance you activate, you will never get the same set of battery power that you can get plugged.

  The battery can not simply support the GPU for the amount of power he needs to play games. At best, you can play a mediocre performance.

• Compaq 6710 b: my HP Compaq power on only when I plug in power. Don't turn on with the power button / stop!

  I have a laptop HP Compaq 6710 b... Its more than 6 years...

  The problem is really annoying... The laptop powers on only when I force taken into the spindle of the charger and the laptop works very well after that...
  But the laptop never turns on when I try to power by pressing the power button!
  I did not understand the reason why...

  Any thoughts on this problem?  Help!

  There are no settings in the BIOS that affect the use of the power button.

  The power button works at the level of the material (firmware).

  By pressing the button translates the action of the Commission of the conditions of the logic system.  There must be voltage at specific points in the power circuit. If the voltages are not present, then the power button does not work. This can be caused by a failure resistance, mlcc capacitor or a bad solder joint, if the power button has been tested and shown to work normally. Fluff even could cause this to happen. This can help out-performed by Visual inspection and using a multimeter.

• Tecra R850 - internal MIC does not work when earphones are plugged

  I factory reset my laptop yesterday and all since the internal mic only works when nothing is plugged into the Jack, including the headphones without a microphone and speakers. This was never a problem before resetting factory and I was able to plug in headphones to hear from people and can use the microphone to talk... now I can only talk to people when nothing is plugged in the sense that I have not heard from people on the speakers of the laptop...

  Any ideas guys? I don't want to have to buy new headphones :/

  See you soon

  It's really crazy. With the factory settings, everything should be OK.
  Theoretically, internal microphone can be blocked if you connect headphones into the microphone port.
  If please check al and don't forget your helmet is connected on the right audio output port.

• 6Plus iPhone vibrates when it is plugged in to the charger

  Hello

  I recently received a 6Plus of the iPhone, which vibrates, rather that in fact no noise when I plug to charge. My previous iPhone (iPhone 5) makes a noise when I plugged it, as does my iPad Mini 4. When all three of these devices have been implemented, I don't know more invited to make a choice as to whether "vibrate or make a noise or both or neither of the two, when connecting to power". I remember that old iPhone 3 g my mother my, or she if current iPhone 5 makes a noise or vibrates when it is plugged, or if it is both. His iPad Mini 2 only makes a noise when it is plugged SOMETIMES. It can also vibrate at the same time SOMETIMES. I can't find any setting to change my iPhone 6Plus to "vibrate when connected to power" "make a sound when connected to power. I also looked for the same thing on my mothers iPad Mini and my Mini iPad AND iPhone 5, but without success.

  I noticed there are a heck of a lot of choice of tones "alert" and "ringtones" and the choice of "modes of vibration" (including the "personalized") as well as the 'Alerts' to make decisions on, but I see NO option to "connect to power.

  Did anyone here knows the answer?

  In addition, if the 'her' vibrator are selectable from the same list as the ringtones and text alerts?

  Hello again,

  I would have closed at the end of the above message, but cut and paste crashed my iPhone 6Plus when writing above message.

  Thanks for any help

  Bob

• Satellite M50 - charges the battery only when stopped

  My Satellite M50 battery only when stopped. Does this mean that when I work I'm still running on batteries, which of course carry out completely after 1 to 2 hours. Then I shut down the computer and it started charging again (orange led), and after a few hours, I still have a 100% charged battery.

  Of course, this means that the computer is not available. Until a few weeks ago it used to have the same problem if I disconnected the power plug then reconnected it: the battery needed to dump then to 0%, even if the power is connected, but now the problem is constant.

  I've updated to the latest version of the BIOS, I could find and even completely reinstall windows from the recovery disks, but the problem is still there. The computer is a Toshiba Satellite M50 - 126 model PSM51E, the BIOS is Phoenix BIOS v2.10

  Is it possible that the BIOS is damaged of some sort? I tried to reinstall V2.10 but he told me that I have the same version and it will not be installed.

  Hi lartech,.

  You can recharge the battery if you get into the BIOS and made the battery charging icon light?
  Are you using the original Toshiba AC/DC adapter and battery?

  In the worst case, it s a malfunction of the motherboard, and you have done what you can do: BIOS update and to install Windows from the recovery disc. If this doesn't help s a bad hardware work.

• Acer Aspire V5 552 slow game performance low when it is plugged into the charger (HELP!)

  So, I recently noticed that my Acer laptop has a problem when it comes to games. The speed of the CPU is really low when you start a game, I did not notice this until a few hours before... I was playing Borderlands 2 and I am disconnected from my laptop to move it to my office and I noticed that my FPS has increased almost double what they were before, I plugged my laptop for the charger and I started to look at the the CPU cores, each carrot got preatty fluctuating between speed and low speed. I've tested this with all my games and all had the same results, for example a Borderlands 2 area when it is plugged in the exercise was about 18-22 FPS, but when disconnected from the charger the FPS increased from 34-48 or more. I tried to read a lot of things on the web and can not find a solution to this...

  Another test I did was with Dolphin Gamecube emulator, the FPS when playing the legend of Zelda The Wind Waker varies between 22-26 or lower on the places of strong thickness, when unplugging my laptop charger I have 30 fps constant in these heavy areas.

  Also with Counter Strike Global Offensive, the game normally ran about 50-60 FPS in all the cards and then tested without the charger plugged in and got 70-120 FPS on all cards

  https://www.YouTube.com/watch?v=xc6Hwgedqmo

  This video shows exactly what happens for me, unless I have an AMD GPU and CPU.

  My Acer Aspire V5 552 Specs are.
  Windows 7 X 64
  8 GB RAM
  AMD A8 - 5557M @2. 1 GHz to 2.8 GHz Turbo
  AMD 8550G GPU
  I have all the latest drivers and updates installed.

  The charger is not damaged, it is original one supplied with the notebook.

  Got a nice deal on a MSI gaming laptop. At first I thought that the Aspire V5 has been an excellent laptop for budget games, but then turned that has a performance problem that ruined the processors to give power maxi while only plugged in, but when unplugged the other way around. Still a nice cell phone with potential wasted with this particular problem.

  No solution to this problem, tecs don't even bother looking at BIOS like other manufacturers of laptop to solve this same problem.

• The screen brightness on battery and when it is plugged

  Good if the brightness of the screen while it is plugged is currently set to '100% ', but I can't seen anything, but when I disconnect screen illuminates a lot even if it is set to '40% '.

  Anyone have any ideas? I tried fiddling around with different power plans, but no luck for now. So I can't basically works when it is plugged in that gets really annoying.

  Cheers!

  Keith, Brian,
  Thanks for your help.
  Its strange, just start works well again.
  The only thing I can think of that has changed is I installed the UniBlue Registry Booster and he had to solve some problems.
  I think that the luminosity set before this thing, but I don't remember for sure...

  So thank you once again,
  see you soon,
  Understanding

• My new ViewSonic LED displays 'signal' when it is plugged

  I recently bought a ViewSonic LED monitor from amazon (option to come back, would rather try to fix first) and it is supposed to be the second monitor. I have my operating system and went to plug the new viewsonic, I now have almost identical 2, the first is an older version, and he gets that "No Signal" then goes to the mode 'sleep'.

  I thought at first maybe its my cables, so I tried the DVI and VGA, it came with and none worked. Then I thought well okay maybe it's of monitor cables, so I disconnected work currently and only used the DVI giving me a display on the current screen. This solution does not work, and I did the same thing with the VGA to see if it would work on the old monitor, which it did, so I tried on the new monitor and without success.

  After that idea, I decided to look at the display settings and when it's plugged the computer recognizes a second screen, but when I select the '2' or second monitor in the settings it greys the option to select it as the main display. Any option to display, I chose it still shows nothing on the new monitor, nor the premiera she acts as if there is more space for work (the mouse let not the current monitor even if I apply the changes. I went to the display settings after I realized that wake up the monitor and look for a signal when I was in him in reconnecting with the DVI or VGA, but it's just never to find the signal.

  My last attempt to see what is going on on what was going on with the monitor has been plugging the same VGA cable that I have been using the monitor in my laptop... BOOM he got the signal, so I said OK well well it must be good. I used the same computer port that gives me a signal on the old monitor and connected to the screen with the same cable that I used with the laptop and nothing. No signal... I'm lost, the only thing I know that I have not tried yet is a HDMI which is my next step but I'm completely lost as to how 1 viewsonic can receive a signal and the new cannot but plug it into a computer laptop and we're ready to go.

  Please help, I'm willing to try all that, I'll send amazon rear t and try a new, but since it turn on with the laptop (not where I want to use it) I thought I could do something wrong.

  Thanks for the input, Niranjan, I appreciate the help and time.

  Just to let you know, I was about to try this, the arrival of my display to VGA Converter, shaped port, it was my last ditch to plug and play. Of course the screen broke on.

  Thanks again for the advice and taking time out of your day to help.

  Have a great weekend.