SL410: lose the power connector (and unidentified metal part)

Similar Questions

• Satellite Pro L300-152 lose the power connector - how to disassemble it?

  I have a Satellite Pro L300 - 152 unit, which is out of warranty.
  I have a bad power connector, it has been pushed back and be dislodged from his seat or brocken cradel is within the computer.

  I am trying to remove the back to see if the power connector can be repaired or remains in its cradle.
  I removed all the screws and all devices, but can not get it off the computer.

  There seems to be something with the keyboard, which I took.

  Can you help me?

  To fix the power connector the whole notebook must be disassembled and you must have access to the motherboard. Disassembly procedure is not complicated if you have maintenance manuals and instructions.
  To have full access to the motherboard, you must remove all the screws from the underside and also all the screws under the keyboard. You will then be able to separate the notebooks and disassemble the upper.

  Tell me exactly what you have removed so far?

• I want to replace the power supply and graphics card in my p6550z

  Hello

  I'm looking to replace my power supply (BESTEC 300 watts) and the graphics card (ati radeon hd 5450). Here is a link to the HP page with my pc: http://h10025.www1.hp.com/ewfrf/wc/product?product=4242359&lc=en&cc=us&dlc=en&lang=en&cc=us

  The card I want to put is an Amd Radeon HD 6870. And I also want to put in a block of power SUPPLY Corsair 550 Watt.

  They will work when I install them? (I'm actually a little nervous about the upgrade my power supply and graphics card since it is the first time I'm doing this) (I'm also nervous because I've heard many horror stories about upgrading an HP computer)

  Hello

  There is a small metal tab inside (guts) on some models of PC HP adds stability to food. You'll have to push the tab down to get food out.  The link below will show this tab.

  How to replace a power supply.

  How to replace a video card.

  Corsair power supply (psu) I used can be mounted with the fan facing upwards or downwards depending on where fresh air is available from. Some PC cabinets have mesh ventilation where the PSU Monte so the fan should face the ventilation mesh so that fresh air can be brought into the power supply and then exhausted at the rear. Some HP computers have slots to air ventilation through the upper edges of the flanks and in this case, the PSU is mounted to the top fan. Otherwise, the Assembly of the fan should be such that the PSU will draw air from inside the Cabinet.

• Qosmio G40: I lose the FN keys and can't get it back

  Hello evryone.

  I need litle help.

  On Qosmio G40 I lose the FN keys and now can't get it back. I close the Toshiba Manager at startup, then now is not in the bar of tasks.
  I think it need to reinstal, but do not know what is the name of the driver.

  Please help.

  Antonio Covic
  Croatia.

  You use the Vista operating system?
  If Yes, then visit the page of European driver of Toshiba and download the Toshiba value added package.
  Remove the old PPV of the G40, then install the new version.

  Good bye

• Pagefile.sys has completely disappeared. It started when the power failed and my computer crashed.

  My pagefile.sys has completely disappeared. This all started when the power failed and my computer crashed.
  I get the message that he was away, I went to the performance and settings and tried to change custom settings & re-start.

  No matter what I do, nothing works. I lost several hours of visiting sites for tips and nothing seems to help.

  I was told when re-boots WinXP it creates the new file pagefile.sys and I should delete the pagefile.sys file may be corrupted on the C drive.

  So I put the folders to show hidden files and delete pagefile.sys. I have re-set and tried to recover with no success.

  There is now absolutely no pagefile.sys on my C drive. Anyone know how I can get back my pagefile.sys?

  I want to get my virtual memory works again?

  Thank you very much in advance!

  I'd start first with the chkdsk/r.

  Don't forget - if you have a factory installed recovery Partition, fixmbr will scan it as the Master Boot Record that written XP will equal not the MBR installed by the factory, so first run chkdsk /r (did I say that already)?

  Here are some instructions:

  http://pcsupport.about.com/od/fixtheproblem/SS/RCONSOLE.htm

  Where people have no XP bootable media, here are my instructions:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• everybody else out there to me who did the OCS certifications and are NOT part of the OPN?

  Someone out there (except me) who did the OCS certifications and do NOT part of OPN?

  I had done a few these just for you to introduce new concepts.

  When there is sometimes an ECA and a certification of the OCS for a subject, I try to stay with the ECO.

  What are the experiences people?

  Thank you Roger

  
  

  I are actually eligible for your first condition since my employer is a partner of Oracle.  That said, I don't take the OCS reviews in order to earn stars of gold for my employer.

  Reviews of the OCS are less technically oriented types of certification. They are intended for vendors and integrators that need to be able to talk about his products and reasonably knowledgeable Oracle making.  Exams I've taken were much more focused towards the fact that there is a given feature and functionality, there with the implementation of the function in the real world. This is not to say that the information that you need to learn how to pass exams of the OCS are not valid. It's good to know what are the features of Oracle products. I have been asked by my employers and past to the opportunity to integrate the feature 'X' into our solutions. Preparation for OCS-level exams can give you an overview of how (or if) given the capabilities of Oracle products can help (or not) in a given situation.

  That said, the OCP and OCE certifications are much more valuable when you really want to learn how to use the various technologies of Oracle.

• is the power connector of 9642XT NI SBRIO J3 negative terminal internally connected to Terminal and mounting holes

  I have a SBRIO system with an isolated supply

  http://www.NI.com/PDF/manuals/375052c.PDF

  It is said on page 15, all connections of Earth GND D AI, AO, connected internally to the earth terminal.

  the negative terminal of the power of the J3 connector is also grounded internally?

  I have a system mounted on a box aluminuim, which owns the land on the Earth, and also the supply, which is used to power the sbrio gives voltage isolated, but now if the negative terminal of the J3 connector has an internal connection with the holes and the spade of Earth, how can I use my isolated power supply with the negative terminal is not connected to the ground its main power supply the connection output not the soil Earth domain controller.

  I can't open my system sbrio jury at that time to check directly.

  can you please help if negative - ve terminal J3 power connector is connected internally to the ground lug and mounting holes.

  Thank you

  Hi Freemason.

  I think I just you send an email in this regard, but to confirm, Yes, connector J3 is connected to earth ground in-house. You should still be able to use your power for the sbRIO.

  Best,

  Dan N

  Technical sales engineer

  National Instruments

• Always have 2 tabs FF15.0.1 and start tabs w/previous/win. No matter when I start FF the second window always loses the 1 tab and put the '+' to the extreme left.

  When I close FF the active window becomes #1 window when I restart. No matter that one becomes a window #2 the first pinned tab is missing and the '+' is on the far left. Same thing happens if the tabs are not pinned. If I close FF and cause a switch between W #1 and 2 W, W #2 loses this 1 tab and w #1 missing tab reappears.

  Hello ppsffvt, it looks like an extension might be interfering here. Please, try to start firefox in safe mode once and see if the problem occurs here also.

  Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox

• Satellite Pro 480cdt: how to replace the power supply and memory?

  I broke the tip of the power where it goes to the back of the computer. The two pins came away from the cable. What is the size of the plug round I am looking for as a replacement? Assume that there is a standard fitting of Toshiba.

  The right size to upgrade as the memory is 128 MB. He got 64 MB it's 2 x 32 MB. I guess we're soldered in, but I can remove the other 32 MB and put the 128.

  Are these modules memory square-shaped?
  Finally, a link to the service manual would be very helpful.

  Thanks in advance.

  Hello

  It's really an old unit and it is not easy to find a lot of information. I found the info that this device can use 160MO max. Module of RAM compatible RAM are:
  16 MB PA2039U
  PA2040U 32 MB
  48 MB PA2041U
  128 MB PA2042U
  I don t really know where is placed expansion slot memory but check the underside first. Otherwise, that it may also be placed under the keyboard.

  Replacement of plug power is a bit complicated, and in this case I can't help you at all.

  In any case good luck with your oldie!

• Will I lose the files, emails, and new photos if I restore the computer to an old backup file?

  Trouble with several of my software design update to El Capitan.

  I'll lose new emails, photos and I have the files, so restoring my computer with an old backup with an older operating system on an external drive?

  If you restore a full plus version of your drive on the existing, you'll be back your mac to the backup day.

  Instead, why don't tell you the readers about the problems you meet and are looking for solutions for those who instead of going backward.

• PSA 30F satellite: how to fix the power connector?

  Hello

  I need to open my PSA Satellite 30F to correct a bad concection in the power conector. Does anyone have a description about how to access this conector? I know that this is the problem and not the AC adapter. The computer is out of warranty, so I'll try to fix it myself. The computer store told me I had to replace the whole motherboard and which would cost me $ 800, Yes!

  Hello

  Well, the problem is that I don't know if the power Jack is soldered on the laptop or only connected m.
  If it s only connected so you can remove all parts, covers, motherboard and then somewhere, you should find the power jack.
  But if it s welded so it's not easy to replace. You should have a very good experience in electronics to fix.

  Check these jacks;
  http://www.laptopking.com/partpicture_LK.asp?ref=404&category=dcjack

  However, there is no official document s how replace this Jack. I guess the Toshiba service partner in your country can give you more details.

  Good luck

• MacBook Pro stops when the lid closes, loses the open tabs and background image...

  Hi all

  I recently had a new hard drive installed in my 2012 13-inch MacBook Pro. I am running El Capitan 10.11.2. Since then, my computer cuts automatically to the bottom when the lid is closed, losing all Web pages, and for some reason, some background, I've saved. (My browser is Mozilla Firefox and it prompts you to restore me the tabs lost, which he will).

  The led standby does not blink or light up when the computer is turned on, it will turn on only at startup. At startup, the login page is displayed, and after that I entered my password it takes about 15 to 25 seconds to load and open my account. What is going on?!

  Summary:

  Stop when the lid is closed,

  Loses the background image & open Web pages.

  Standby blinks only when starting,

  Time of loading extended after logging into my account.

  Any help would be greatly appreciated! Thanks a lot for reading.

  uhlexia wrote:

  Hi all

  I recently had a new hard drive installed in my 2012 13-inch MacBook Pro. I am running El Capitan 10.11.2. Since then, my computer turns off automatically when the lid is closed.

  Take it back to the repair as well as your receipt of repair shop.  Apple has a 90 day warranty on all repairs.

  

• Where can I get the power sources and accessories for the Xbox 360 in India?

  XBox360 power supply model: NHPD-186DB a 110-240 v / 203W

  Hello

  Microsoft - India
  http://www.Microsoft.com/en-in/default.aspx

  XBox - India
  http://www.Xbox.com/en-in

  XBox - India - support
  http://support.Xbox.com/en-us/?XR=shellnav

  Major retailers in the region may also be able to help.

  ========================================================

  These are the resources of the United States and it should be similar for Microsoft India.

  XBox - Support<-- best="">
  http://support.Xbox.com/en-us/pages/default.aspx

  XBox - Contact us (support)<-- best="">
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)<-- might="" be="" some="" good="" information="">
  http://forums.Xbox.com/

  Xbox technical support phone number

  • Toll-free: (800) 4MY-XBOX or (800) 469-9269

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• lost hibernation startup command menu, why can't find it in the power options and enable the Hibernate?

  tried the right click, properties, screensaver, power office and cannot find a way to afford to hibernate again. When I try the "turn Hibernate power" listed in the left hand blue, he takes me in power options, but said that I can choose to quit, sleep or do nothing. don't Hibernate tho.

  Hi Twyla,

  Start with this article: http://www.ehow.com/how_7591373_add-hibernate-shutdown-options.html.  If this is not the case, then discover the many other links and references on that page and I'm sure you'll find something that covers the problem.

  Good luck!

• Windows Vista 32 on Netbook MSI, I plug in the power adapter and a few minutes later get blue screen and restarts of netbook.

  I installed windows vista on my MSI Netbook and I did all the updates of windows.  After the 2nd service pack if I unplug the power and plug it later back I get the blue screen and restart. Let the blue screen so quickly I can read just debug USB driver or something. I tired it in safe mode, and it does not occur in safe mode. Can someone help me?

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been postponed until February 26, 2010, so move on! Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack <=you want="" this=""> ). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft