Smart Link backup VPN (RV042)

Similar Questions

• Issue backup Smart Link

  I have a small business RV042 router.  I have the Dual WAN setup Smart Link Backup mode.

  WAN1 is configured with a DNS servers for ISP 1 and the specified static IP address.

  WAN2 is configured to 2 PSI with a dynamic IP Addess (obtain an IP address automatically) with no DNS information is entered.

  If I unplug the cable to WAN1 router fine WAN2.  The problem I have is that DNS fails on all my computers until the cable to WAN1 is reconnected.  If when the WAN1 is disconnected, I do an ipconfig/release then ipconfig / renew on my computers, the DNS lookups so fine function.  If I plug the cable in to WAN1 I still do ipconfig/release then ipconfig / renew on my computers again have DNS function correctly.

  Any ideas on how this can be corrected?

  Static DNS servers can be specified to the DHCP > Setup page. The configured DNS servers thus will take precedence over the DNS servers provided by your ISP, when WAN links go live.

• How backup VPN configuration between two universities?

  Hello, I am a student of the Greece and I have a graduation project to configure Backup VPN between two universities. Principal of communication made with leased lines. I study a lot, but now that it's time for implementation I have some thoughts:

  -What hardware and software IOS do I need? Cisco 1841 it is ok for A & D routers?

  -Use GRE IPSec transport mode or IPsec Tunnel mode?

  -What will be the failover mechanism for switching traffic lines leased to IP VPN Backup and opposite? A teacher told me something about the Interface Prioritys. I read somewhere that this is done with the such as EIGRP routing protocol. who was right the Professor or the book?  :-D

  -In the same place, they have Firewall and NAT, I need to do any action for this?

  The attached file contains topology I want to implement

  'My' talk site 1

  2 a Central Site

  E communicates with A, but no traffic is to A of E with normal circumstances. Subnet on E access Internet through F, then press D.    VPN will be implemented on the LAN but the specific source E traffic will pass through the Backdoor VPN (I think that the solution to this is ACL on the router). They have no routing protocol in 'my' site A directly connected routers and the default routes.

  How imlement this?

  I think the first thing to do is A to D connectivity

  I will try to do this to tracers package first, but how can ' I imitate the SP network?

  I need help I can get!

  Hi John,.

  In our scenario, given that our main connection is a direct leased line between E and F, so I guess there is no other network between the two routers. In this case we do not need to configure SLA monitoring or any interface a priority. We can simply enter two default routes:

  IP route

  IP route 254

  In this scenario, if the leased line interface goes down, the second default route is used and the traffic should be routed by A router.

  SLA monitoring monitors connection (using the ping tests) by one of the interfaces of the router, and when we are not able to ping from one server (specified in the configuration of the SLA) through the interface, then we change the default track to track traffic through some other interface.

  So, in your scenario, we can monitor the connection between E and F, and when the link goes down, we can change the default route to point a.

  This is useful in the scenario where we have another ISP connection as our primary connection.

  Here is a link on how to configure SLA monitoring on the router:

  http://www.Cisco.com/en/us/docs/iOS/12_4/ip_sla/configuration/guide/hsicmp.html

  After you have configured the SLA followed by using the link above, you can bind it to the default route by using the following command line:

  track road IP / / default main route

  IP route 255 / / default route with a metric of higer that comes into play when the main default route goes down

  In addition, the sample configuration that you give in the doc is almost correct, defined transformation is missing just a hashing algorithm. Here is a link with an example for a tunnel from lan-to-lan between two routers:

  http://www.Cisco.com/en/us/partner/products/HW/routers/ps221/products_configuration_example09186a008073e078.shtml

• Portal Smart Link

  I built a page based on a template. I have a region that is configured only for ITEMS. I can make this region based on a HTML template.
  
  In my page template, I added a region and added a 'Portal Smart Link' to 'change '. My region of element is designed to allow specific users the ability to add items to the portlet. It all works very well. However, my problem is that the 'Edit Page' smart link is visible to all USERS. In other words, when a user authenticates to the portal, when accessing this page, they see the 'Edit Page' link. This link should not ONLY be visible to users who have permissions to add items to the page?
  
  Thanks in advance.

  Basically, if you have any question level security enabled on a page, all users will see the link change. However, they see the link, does not mean that they can actually change anything if they do not have the privileges to do so.

  For more information, see Note 368720.1 'when THEY turned on the Smartlink Edit is visible to users who do not have right to see' on My Oracle Support (fka Metalink).

• backup smart link does not not in RV042

  I'm in the mess I have configured RV042 in backup of secruit BI (primary/secondary links), but the question is when primary folds secondary does not gets to the top. for this I hv to remove manually main link only the cable then secondary stand... Vica-versa.

  I bought this router for auto backups but if I hv to display manually the same I was mistaken.

  is thr any soluton for that.

  NET detection, I chose the HOST ip. that is my server ip address.

  Pls help me guys. I can provide more details if necessary.

  Hi, paritly problem solved when smone told me to delete connection in Setup...

• Cisco ASA: Vpn SiteToSote with a backup VPN

  Hi all

  A partner have two VPN gateway. We have a connection on one of them, but we want to set up another tunnel for backup (if the first gateway goes down).

  How can I configure my ASA to only create a tunnel with a counterpart if approves it first failure?

  Thanks for the reply

  You can use multiple addresses peer in your map of cryto for example.

  card crypto mymap 10 set by peer

  Your ASA will use try in the order that they are entered, check out this link for more details.

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/c5_72.html#wp2066090

  Jon

• What scales smart link to health app?

  Ready to buy a smart scale. Those of you who will link the health iOS app?  Elle, Garmin, Fitbit, etc...

  According to technical data sheets:

  http://www.Apple.com/shop/product/HB930ZM/B/Withings-smart-body-Analyzer

  Withings seems to be advertising that they support health app directly, while others maybe not so much.

  Fitbit, according to other customers didn't seem to do this, but rather integrates with their own fitbit approx. Garmin is the same.

  Essentially, what I see is that if the company made an effort to integrate health of Apple app, they put themselves in the apple.com store inventory.

• Setting up VPN - RV042 v3 issues

  Hi guys,.

  I just bought a version of Cisco/Linksys RV042 3 and having difficulty getting my Macbook Pro running IPSecuritas to establish a VPN tunnel.

  I get a message "Error - IKE - no message should be encrypted" in the journal of connection IPSecuritas. It will keep retrying which results in the same error. Finally, it gives just straight up.

  I'm sure that I have the settings on the router and configured in the same way Macbook of VPN end.

  Here is a screenshot of the RV042 configuration page. Any input would be greatly appreciated, thanks:

  

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• Wireless and VPN RV042 router WRT54G

  Respected member, please help if you can! I have an ADSL with dynamic connected with the wrt54g router, I recently bought RV042 and want to connect the wire coming from wireless with ports. so, basically, I want to use RV042VPN for help after the router, is there a way I can use vpn behind with port using RV042 router wireless

  I can't be able to connect to the vpn as he seeks is not an ip or WAN/LAN.

  It may be possible if you're lucky. But I highly recommend not to connect the RV042 after the WRT. A VPN server must always have a public IP address. Running a VPN server behind a router NAT (such as WRT) makes it extremely difficult and often it won't work at all. Connect the RV042 directly to your modem, configure it to your internet connection. In this way the RV042 has the public IP and VPN should become much easier. Then implement the WRT as simple access point in your network by changing the address LAN IP of 192.168.1.1 to 192.168.1.2, disable the DHCP server, and connect a LAN port of the WRT on a LAN on the RV042 port.

• aid required for the image backup vpn concentrator

  Hi, I am unable to download the vpn concentrator ios image to the tftp server. is someone can pls tell me what is the procedure for that. I can't find good documentation on it. pls help someone.

  concerning

  Assane

  Assane,

  You try to save the image of the hub to the VPN concentrator. Like the 4.7.2.D or the version E or F of the code. If this is the case, it is not possible to copy the image file from the hub to the tftp server.

  You must download the CEC file.

  He had an answer to your question earlier, but it pointed you on how to make a backup of your CONFIGURATION file.

  If this answers your question, feel free to write it down.

• Dial backup VPN - pre-shared key question

  I use dial backup for my DSL connections in case of failure, but on my host router I also use EZVPN Client VPN access server. Thus the server EZVPN uses xauth for pre-shared key authentication:

  ISAKMP crypto key? address 0.0.0.0 0.0.0.0

  BUT for my backup of VPN connection to work, I need to use the dynamic IP to the IP address of the peer that requires:

  ISAKMP crypto key? address 0.0.0.0 0.0.0.0 no xauth

  I tried to set the keys for dial-in subnets, but it always seems to use the default value.

  Is this all just not supported or is there a workaround?

  My (main) the host router is a CISCO 1841, my remote router is 877.

  See you soon,.

  Sean

  You need to configure ISAKMP profiles on the server Ezvpn router.

  http://Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00801dddbb.shtml

  Who would do it.

• Backup VPN IPsec

  Hello

  I m a few problems in the creation of a tunnel VPN Backup.

  I have HQ with a router with a primary circuit on F0/0 and a backup on F0/1 circuit

  Then I have an office with a headquarters with an IPSec VPN tunnel connection.

  The problem is that the tunnel monte and everyting is fine when you are working with the primary circuit, but when it comes down the escape tunnel does not, so the ping between the LAN of HQ and Branch LAN stop.

  Can someone help me and give me a light?

  Thanks in advance

  CONFIG HQ

  host CUSTOMER name

  !

  interface FastEthernet0/0

  IP 210.50.50.1 255.255.255.0

  NAT outside IP

  !

  interface FastEthernet0/1

  IP 213.50.50.1 255.255.255.0

  NAT outside IP

  !

  interface GigabitEthernet1/0

  IP 192.168.1.254 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  auto negotiation

  !

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0 FastEthernet0/0

  IP route 0.0.0.0 0.0.0.0 FastEthernet0/1 100

  !

  IP nat inside source map route isps1 interface FastEthernet0/0 overload

  IP nat inside source map route ISP2 interface FastEthernet0/1 overload

  !

  NAT extended IP access list

  deny ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255

  ip permit 192.168.1.0 0.0.0.255 any

  !

  route allowed ISP2 10 map

  corresponds to the IP NAT

  is the interface FastEthernet0/1

  !

  isps1 allowed 10 route map

  corresponds to the IP NAT

  is the interface FastEthernet0/0

  !

  DIRECTORATE GENERAL OF THE CONFIG

  hostname CUSTOMERB

  crypto ISAKMP policy 100

  preshared authentication

  ISAKMP crypto key cisco1234 address 210.50.50.1

  ISAKMP crypto key cisco1234 address 213.50.50.1

  !

  Crypto ipsec transform-set esp RIGHT - the

  MYMAP 100 ipsec-isakmp crypto map

  defined by peer 210.50.50.1

  transformation-RIGHT game

  match address VPN

  MYMAP 200 ipsec-isakmp crypto map

  defined by peer 213.50.50.1

  transformation-RIGHT game

  match address VPN

  !

  interface FastEthernet0/0

  IP 200.40.40.1 255.255.255.0

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  crypto MYMAP map

  !

  interface FastEthernet0/1

  192.168.2.254 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0 FastEthernet0/0

  !

  overload of IP nat inside source list NAT interface FastEthernet0/0

  !

  NAT extended IP access list

  deny ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255

  permit ip 192.168.2.0 0.0.0.255 any

  list of IP - VPN access scope

  permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255

  !

  The Scenario

  

  very simple solution.

  1 - Create a loopback interface lo0 on customer with a public IP address and make sure that the loopback IP address is accessible on the Internet by CustomerB

  2 create an IPSec between customer and CustomerB use customer loopback0 as source card crypto 'card crypto source loopback0' or something like that on customer,.

  3. on the CustomerB, use only the loopback0 address customer and the VPN peer.

  In this way, IPSec will work "independently" was looking for isps1 or ISP2 is available, assuming that the closure is accessible via isps1 and/or ISP2 files.

• Phones smart blackBerry backup Torch

  I need my flashlight to send for re-formatting of backup. I created a backup using BB Desktop Manager file, but it will include the username and password that I stored in password Keeper App? If not included, how can I save the user name and password stored in the application? Help, please. Thank you.

  Hello

  Yes, the info in your password keeper will be saved during your backup software Desktop.

  When you get your BlackBerry upward and running, all you need to do is to restore your data and you will be in.

  I hope this info helps!

• Cisco ASA 5505 Dual-ISP backup VPN

  I am creating a tunnel of an ASA 5505 to a pix 501 backup in the case of the failure of main Internet service provider.  The external face of Pix will remain the same, but not quite how I can create a new card encryption and it use backup ISP interface without down the main tunnel.

  My first thought was to add the following encryption to the configuration below card:

  card crypto outside_map 2 match address outside_1_cryptomap
  peer set card crypto outside_map 2 9.3.21.13
  card outside_map 2 game of transformation-ESP-DES-MD5 crypto
  card crypto outside_map interface backupisp--> but that would break the current tunnel.

  NYASA # sh run
  : Saved
  :
  ASA Version 7.2 (4)
  !
  NYASA hostname
  domain girls.org
  activate the encrypted password of CHwdJ2WMUcjxIIm8
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  10.1.2.1 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 9.17.5.8 255.255.255.240
  !
  interface Vlan3
  Description backup ISP
  nameif backupisp
  security-level 0
  IP 6.27.9.5 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  switchport access vlan 3
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  DNS server-group DefaultDNS

  outside_access_in list extended access permit icmp any any echo response
  outside_access_in list extended access permit icmp any any source-quench
  outside_access_in list extended access allow all unreachable icmp
  outside_access_in list extended access permit icmp any one time exceed
  outside_access_in list extended access permit icmp any one
  inside_nat0_outbound to access extended list ip 10.1.2.0 allow 255.255.255.0 10.1.1.0 255.255.255.0
  inside_nat0_outbound to access extended list ip 10.1.2.0 allow 255.255.255.0 10.1.100.0 255.255.255.0
  outside_1_cryptomap to access extended list ip 10.1.2.0 allow 255.255.255.0 10.1.1.0 255.255.255.0
  outside_1_cryptomap to access extended list ip 10.1.2.0 allow 255.255.255.0 10.1.100.0 255.255.255.0
  access-list extended 150 permit ip any host 10.1.2.27
  access-list 150 extended allow host ip 10.1.2.27 all
  pager lines 24
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  backupisp MTU 1500
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 524.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  interface of global (backupisp) 1
  NAT (inside) 0-list of access inside_nat0_outbound
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 9.17.5.7 1 track 1
  Route 0.0.0.0 backupisp 0.0.0.0 6.27.9.1 254
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  the ssh LOCAL console AAA authentication
  Enable http server
  http 10.1.2.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  ALS 10 monitor
  type echo protocol ipIcmpEcho 4.2.2.2 outside interface
  NUM-package of 3
  timeout of 1000
  frequency 3
  Annex monitor SLA 10 life never start-time now
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 9.3.21.13
  map outside_map 1 set of transformation-ESP-DES-MD5 crypto
  outside_map interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  the Encryption
  md5 hash
  Group 2
  life 86400
  Crypto isakmp nat-traversal 20
  !
  track 1 rtr 10 accessibility
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 60
  Console timeout 0
  management-access inside

  ptiadmin encrypted BtOLil2gR0VaUjfX privilege 15 password username
  tunnel-group 9.4.21.13 type ipsec-l2l
  IPSec-attributes tunnel-Group 9.4.21.13
  pre-shared-key *.
  !
  !
  context of prompt hostname
  Cryptochecksum:22bb60b07c4c1805b89eb2376683f861
  : end
  NYASA #.

  Thanks in advance.

  In this case is the PIX in need of two peers (to the ASA).

  The ASA is it requires the card encryption to be applied to the interface of backup as well (as you mentioned)

  card crypto outside_map interface backupisp--> but that would break the current tunnel.

  The command above should not break the current tunnel (if the road to reach the other end goes out through the main interface).

  In addition, you must IP SLA configured in the ASA to allow him to use the primary connection and aid for the connection of accumulation relief tunnel (both to reuse the primary interface when she recovers).

  Federico.

• Add a static route to a RV042

  I have configured the RV042 dual WAN port for backup smart link connected to two different ISPS.  The subnet behind this is 192.168.2.xxx.  I have a second router linksys Garland with the 192.168.2.250 WAN port and subnet behind it is 192.168.20.xxx.  My problem is that I have a not able to route traffic fron 192.168.2.xxx to 192.168.20.xxx.  How can I add a static route so that clients on 192.168.2.xxx can access resources on 192.168.20.xxx?

  1. the second Linksys router must be changed of gateway (active NAT) in router mode (NAT disabled) mode. With NAT the LAN behind the second Linksys will be not accessible from the outside unless you configure port forwarding.

  2. on the RV042 set up a static route for the subnet 192.168.20.0/255.255.255.0 to the gateway IP address 1921.68.2.250 on the LAN interface.

  3. Ideally, you must configure the same static route on all clients connected to the RV042. If you don't want to do this, you must configure the firewall on all clients on the RV042 accept ICMP redirect messages. This is important because otherwise all traffic from 192.168.2. * to * 192.168.20 would be sent to the RV042 and from there to the second Linksys that is unnecessary and could create a bottleneck.