Software HP Photosmart C5180 doesn't install properly

Similar Questions

• problems installing software hp photosmart c5180

  Hello my c5180 and my 64-bit windows 7 will not match

  It wil not install more software hp for printing / scan / copy.

  who can give an idea, s/help

  its starts with fr installation a few minutes later, gone is the installation screen.

  and nothing happens?

  I tried:

  AIO_CDA_Net_Full_Win_WW_130_140

  Thank you

  Hello jvdl,

  Welcome to the Forums!

  I saw your post on the questions you have install your Photosmart C5180 on your Windows 7 computer. I understand the installation will start, and then stop and disappear.

  I would suggest after each step from the document below to hopefully help you to install the software.

  On the Software Installation progress bar stops or crashes

  I hope this helps you!

  Good luck

• Photosmart 7520: Access to the software Scan Photosmart 7520 disappeared when installing Windows 10.

  I went through the procedure of doctor scan and installed the updated software.  Poster proceedings finally the familiar screen send me three options; I chose scan option and it worked perfectly.  My problem is the office at current address printer icon does not find these options, instead it addresses the single ability to USB printer or internet installation.

  How to place an icon for scaning or restore old icon printer options? Where is the scan feature triger?  TIA

  After reading the solutions Win 8.1 for lack of tune, I searched C:/.../Program Files(x86)/HP/HP Photosmart 7520 series/bin/for one tune and HPSan.exe found.  I made an icon of office for this program and I seem to have the same access that I lost.  It works!

• HP Photosmart C5180 - Windows 7 64 bit - network - device detected but FAIL to install.

  Hello

  I have a Photosmart C5180, connected with an ethernet (not usb) cable.

  It's great to work with all the computers in the House (vista and xp).

  But my new computer, a 64-bit windows operating system 7, impossible to install the drivers:

  The drivers are now installed, but the step 'add a device' does not work correctly.

  After the analysis of network, the printer is displayed:

  

  Then I click Next, to "network analysis":

  

  OK, next step is "installation." Before the picture, it says 'detected printer"(french).

  

  And a few seconds after it fails:

  

  Grrrr wtf?

  Thanks for the help!

  I had problems to install the HP software. When I installed the full package I get pop ups and error messages. So I did a complete reinstall (I have now if he really had to do I had other issues). After that I just installed the drivers and no extras and it works very well. I'm also hooked using the ethernet connection. A point even before the reinstall if I come you drivers and no additional software. I can still scan using Windows Fax and Scan. I probably will not add extra software until there is another version.

• Photosmart C5180 duplexer installed Q5582 cannot select the automatic mode

  I recently installed a duplexer Q5582A on my Photosmart C5180. Tried to select Auto Duplex but only manual available.

  • Windows 7
  • updated printer driver
  • Under printer properties, device settings, options installation, no fall to the bottom/duplex available to choose from.

  Any help is appreciated.

  Hello

  The C5180 provides all the features of automatic duplex printing, part Q5582A is only for templates that are specific, not including the C5180 model.

  I'm afraid that such a device is not supported by the software or firmware of the printer

  You can find any part available for the C5180 listed below:

  http://support.HP.com/us-en/document/c00875846

  Shlomi

• A BLUE screen came stating "check to make sure that a new hardware or software is installed properly...".

  Original title: igdpmd64

  When using my computer (laptop).  Version of Window 7 6.1.7601 Service Pack Build 7601

  A BLUE screen came stating "check to make sure that a new hardware or software is installed properly...".

  Disable the BIOS memory options such as implementing caching or shading... If need to use mode without failure to delete or diasble components, restart the computer, press F8 to select Advanced Startup options and then select Safe Mode.

  Technical information:

  Stop: 0 x 00000050(0xFFFFF88168082EA0, 0x0000000000000000, 0xFFFFF880067A5878,0x0000000000000005)

  base address igdpmd64.sys FFFFF880067A5878 at FFFFF8800664B000, DateStamp 4d41a3e1

  What should I do? Right now I'm in Mode safe mode with networking

  Finally, starcraft 2 is installed. Thank you!

• HP Photosmart B110a - "the software for this device is not installed" when scanning on OSX 10.9

  I hope someone can help with this! I am tring to use my scanner without success with the ' software for this device is not installed.

  Measures taken so far

  On a new copy of the Mavericks with installed updates (10.9.2) I added my wireless printer successfully and I can print my documents successfully. My Mac has recognized that this printer includes a scanner and the scanner appears in the preview, capture of the Image etc.

  Problem

   

  
  During an attempt of a scan in any of Mac programs a message that says "the software for this printer is currently unavailable. Contact the manufacturer of the printer to the latest software. "is displayed. There seems to be no software or drivers on the HP site for my scanning equipment. I simply said that it is all built into OSX. I checked the printer on Apple's site and it is listed as supported for printing and scanning. I hope someone can help!

  Finally, I snapped this.

  When you add the printer it seems that OSX AirPrint as the default printer driver.

  To solve this problem, I completely deleted the printer, the printer readded but changed AirPrint for my specific printer driver and all my scanning functions are now available.

  Thanks for all your support!

• Vista Photosmart c5180 driver problem

  Can anyone help - when I start Word by clicking a file in Outlook, when I quit Word I get an error meesage and it can:

  Temporary workaround available

  This problem was caused by a known issue with your Hewlett-Packard printer driver, which causes the close unexpectedly when your HP printer is set as the default printer Microsoft Office 2007 programs. Hewlett-Packard is aware of the problem and working on a solution.

  What is a driver?

  Power to Turn-off of your HP Photosmart C5180 all-in-One, uninstall the current HP software and drivers, then download and install the latest drivers from HP:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=1153481&LC=en&cc=us&DLC=en&lang=en&cc=us&submit=go%20

• Photosmart C5180 using Windows 8. Error message = Z:\is is not accessible - the handle is invalid

  I just bought a new computer with Windows 8.  I loaded the software for my Photosmart C5180 all-in-one printer.  It seems to print fine but when Itry to read a memory card I get an error message: -.

  Z:\is is not accessible - the handle is invalid

  Hello numuc95.

  I guess that the printer is installed network? Have you tried to install the printer with a USB cable? This seems to work best for access to the card reader.

  If you can not install with USB, look at this link to see if it helps:

  http://support.HP.com/us-en/document/c00149194

  I hope this helps.

• Photosmart C5180 - not possible to uninstall the drivers

  I want to uninstall my Photosmart C5180 of PC software, but it s is not possible. I also tried first to do a new install of the compleate, before uninstalling software - same result.

  Every time when I start the PC, I got an error message that says no connection to "TryApp"?

  How solv this problem?

  Hello

  Thank you for your reply,

  To uninstall the software, click Start and click on run in execution type folder window and click OK. This will open the Temp folder, in the eyes of temporary folder for the folder that starts with open 7Z file 7Z and then open the Utils folder and then open the CCC folder and double click on Uninstall_L4.bat and this will start the uninstallation process. Once this completed, please restart the computer and check.

• SD card in Photosmart C5180,

  When I put an SD card in my Photosmart C5180 and try to 'save the photos on the computer' I get a msg "you must install the software for the device", I have a new CQ2014 of Compaq PC, with Win 7 and 64-bit

  Hello

  Install the full feature software below?

  http://ftp.HP.com/pub/softlib/software11/COL30777/MP-76232-1/AIO_CDA_Net_Full_Win_WW_130_140.exe

  If this isn't the case, be sure to first disconnect the USB port.

  Enter the control panel > devices and printers.

  Right click on the C5100 printer icon, and then select Remove an instrument.

  Restart your PC and follow the installation.

  Kind regards

  Shlomi

• Photosmart C5180 Installation ERROR - Windows 7 64-bit - system cannot find the file hpzprI40.exe

  Photosmart C5180 all-in-One

  During the installation:

  C:\Users\Test\AppData\Local\Temp\7zS1DB2\Setup\...\hpzdrI40.exe - m...

  The system cannot find the specified file.

  I clicked OK, then came next to the top:

  Error Situation code: 06768865

  The following lines were extracted from installation error logs.

  + Launching 0000000000001246128\s\Now = X:\hpzprI40.exe m

  preloadiceenginetoguidfolder-* "X:\autorun.inf" - nosplash - checkPath

  XXX-1-f "X:\hpoins18.dat" "-number validate dat"-No. validate "

  Found source file: X:\hpzsetup.exe

  VerifyFilesNoDecompression() failed with the system cannot find the specified file.

  Exit code = 2

  H E L P!  I don't know what to do now.  I tried to install the downloaded file, AIO_CDS_Net_full_Win_WW_130_140 on HP site.  My operating system is Windows 7 Ultimate 64-bit.   I need to get this working today and need complete instructions on what and how to do this fix.

  mrsjeffyg, I recommend that you completely uninstall the printer from the computer. Make sure that all copies of the printer and the associated files are removed from programs and features, the Manager of devices, and the devices and printers. If you are connected with a USB cable, make sure that the cable is removed from the printer for the duration of the present.

  Click START and type "%temp%" and press ENTER. This will open the temporary folder, and I want that you delete all the files that you can here. Some will not be able to be deleted, so ignore these files.

  Restart your computer.

  Follow this link here and reinstall it from the Full_Feature Driver and software.

  http://goo.GL/0zXiT

  I would like to know how it goes!

• Wireless laptop cannot connect to Photosmart C5180 printer on network

  I recently got a new computer, which is the main connection to our home network.  We have a laptop and a Photosmart C5180 printer.  I can't get the wireless laptop to connect to the printer, even though I have the shared printer on the pc.  I have the printer connected to the pc via a USB cable.

  I see the printer shared and available on the laptop, but get the error message when you try to print.

  Does anyone know what I'm missing that will allow me to print from wireless laptop?  It worked until I'm the new pc, so I know I'm missing something.  Should the laptop have both installed printer software/drivers?

  Yes, the printer directly connected to a router with an Ethernet cable will be the simplest solution.

  Yes, all computers will be able to access the printer on the network as long as they are connected to the same router (Ethernet or wireless, regardless).

  He shared from the computer and the printer connected to a computer with a USB cable are not a real printer on a network.  This creates what is essentially a print server and the computer with the USB connection manages the interaction of this printer with all the devices on the network.

  A USB connected printer sharing can be done, but it's a lot more work that the printer is connected to the router with an Ethernet cable.

  It's really a lot more work to set up the printer with a printer shared over a network connection USB method true when it comes to do this with Windows 7.

  Windows XP made it incredibly simple, but he was not very secure on a network.  With Windows XP, all you had to do was to share the printer, and then install it on another computer.

  With Windows 7 on both computers, you must configure a homegroup, enable file sharing and printers (disabled by default), share the printer and install the printer on the computer client / remote.  In addition, this method will require the host to be on anytime for remote printing machines.

  The printer is connected to the router with a Ethernet means that the functionality of the printer depends solely on the router being on (most are on 24/7).  Computers will print regardless of the other computer either on or off.  There should be a shorter time in the impression that a computer is responsible for printing rather than two computers.

  Again, I will be more than happy to help you set up with the method USB shared with two Windows 7 computers if that's what you want.  You find that it is much easier to use the Ethernet connected method to be simpler and more efficient to print well.

  If you want, here's a little more information from Microsoft on sharing a printer between two units of Windows 7.

  Setting up a homegroup

  Activate the file & printer sharingand sharing the printer on a Windows 7 computer

  As long as the printer & file sharing is enabled and two Windows 7 computers are in the same group of residential, you should be able to use the USB share method.  Without these two two options being Setup, it simply does not work with two Windows 7 systems.

• Photosmart C5180 HORIZONTAL lines appearing suddenly on all scans

  I get horizontal lines randomly on all my scans all of a sudden when I use my Photosmart C5180 all-in-one.  Scanned a few things this afternoon and everything was normal.  Then, suddenly, a scan I did had much random horizontal lines (perpendicular to the direction of motion of the trolley) appearing thereon.  When the scan is in color, the lines are of different colors.  On b/w scans, the lines are black.  They appear in different places if I rescan and are random.  They are between 1/4 "and 1" long.  Any ideas?

  Please do not send all of the links for troubleshooting vertical lines, as is not the same problem.  In addition, it is scanning only... printing functions remain normal, please so no printer/ink articles either.  Is longer under warranty so it doesn't get service unless I pay extra, and I don't want to lose money if I just need a new machine.

  Any help is greatly appreciated, even though I'm starting to think that the solution is to buy a new all-in-one.

  I don't think you can buy a HP spare bulb, but you might find them on sale on 3rd party websites (but reliability then comes into question). If you were able to get a spare bulb, so you will need to find someone qualified/tech-savvy enough to replace it.

  I think that ultimately, you could end up spending more to look for party and someone to install it as you would on an all-in-one replacement. You could buy a separate however scanner and continue to use the C5180 for printing.

• WiFi doesn't connect properly & apps not updated by wifi

  Mr President

  When I update 9.3.2 wifi doesn't connect properly & apps not updated or installed via wifi and battery low.icloud does not

  gsuryakiran wrote:

  Mr President

  When I update 9.3.2 wifi doesn't connect properly & apps not updated or installed via wifi and battery low.icloud does not

  Follow the 3R - if this does not solve your problem proceed

  Troubleshooting of user is:

  1. reboot, IE power off / on,.

  2 reset http://support.apple.com/kb/HT1430,

  3. restore the backup, restore as a new device. http://support.Apple.com/kb/HT1414