Sometimes, my Mac is unable to find other devices on my Wi - Fi

Similar Questions

• Installation of up4 on up3 "Unable to find supported device..." »

  I'm getting high grade to up4 build 153875 of 143149 using the drive working even, but it fails with the error message "Unable to find supported device..." ».  The old version of ESXi works very well on the disc.  I can load on the drive.  Any ideas on how this can be resolved.

  Thank you

  Have you tried that? http://www.vm-help.com/esx/esx3i/no_persistent_storage_after_upgrade.php.

• Unable to find the devices on the network of field

  Hello

  I'm currently setting up a network of field. The problem I have is:

  After the reboot of the PS-2000, everything starts up as usual, but after 15 seconds, the A, B, C, D LEDs do not turn off, and READY LEDs on the IO modules never turn on. The STATUS LED does not blink, there is no specific errors. The POWER LEDS on the set of the modules is on. I am unable to use the FIND FEATURES within the NOT-MAX, a 'Connection Timed Out' (or something to that effect) error message occurs.

  I have correctly configured an IP address on the PS-2000, I am able to view the files on the Flash using the FTP transfer in NOR-MAX, I updated the Firmware LabVIEW RT v7.0.0. I tried to reinstall the firmwar
  e and resetting the PS-2000, but nothing helped.

  To simplify the issue, I unplugged the PS-2000 from the rest of the basics of connection. I inspected the
  pine trees on the side of the module and they looked fine. I couldn't find all other versions of the Firmware for the PS-2000 on the NI download site, just in case my version has been altered. With this configuration, the A, B, C, D LEDs are still on, and the FIND DEVICES (not that there there) always times out.

  Then I tried to plug in a FP-TB-10 (with only input modules out there, so that there would be no external power required), and I still have the same problems.

  Material used:
  PS-2000
  -2 * FP - TB - 10 popular with a mix of I/AO/DI/DO
  FP-QUAD-510
  -FP-PG-522

  Power supply:
  -Kepco power out 16 VDC and approximately 0.4 A (+ terminal connected to V and neutral terminal connected to C)

  Software used:
  -LabVIEW Professional 7 with RT
  -MAX 3.0

  Unfortunately most
  the user manuals still refer to the field Point, as opposed to the NOT-MAX Explorer.

  Any suggestions for my experiences above would be welcome! Is there anywhere I can download the firmware Lv7.0.0 RT? Everyone knows about similar problems with LV7?

  Thank you!

  I will answer this myself!

  The issue proved to be a limited set of software installed on the FP2000. When I was installing the software, setting up NO-MAX, the only available software is LabVIEW RT v7.0.0.

  When you install the software (from NOR-MAX) on the ps2000 for the first time, the following text should be available:

  -Control environment FieldPoint
  -Manager of VI FieldPoint
  -LabVIEW RT
  -RT OR Serial
  NI-VISA
  OR-Watchdog

  If none of them are not available, the module PS, or downloadable from the NOT-MAX, then not all device drivers have been installed on the PC.

  Use your device provided with LabVIEW drivers CD to install all the necessary drivers of RT.

• I can't find other devices on my network.

  I use a WNDR3700x2 router with a wireless on another floor extension. When I connect to the router itself, I can see all of our devices, wired and wireless. I also downloaded the netgear genius app, and they appear there, too. The problem is that my devices cannot communicate with each other and do not lie when I display the networks on the devices themselves. All computers are running Win 10 and wired and wireless internet access works great. Through files and printers sharing, I managed to get a wireless laptop to talk to a desktop computer, but by the Wireless Office, too. The files are now accessible by computers, but the laptop does not see the printer that is hard wired to the desktop. (Before 10th of Windows, wireless computer could talk to another computer when it is wired - that no longer works.) I am also unable to see desktop computers from another computer wired or wireless laptop.

  I think I'm being stupid here, but I'm tired of banging my head against the wall... I read another post on this subject, where the global address list should restart router sound every morning for its computers to see each other. This is not the case in my question; restarting changes nothing, and the router connection shows all the devices - I can't get them to see through computers.

  Thank you, Elaine! For some reason, using the genius of Netgear has allowed these computers to communicate again. It has no sense to me why it would change anything, but it did, and now all computers communicate with each other. Intermittent problems with the printer, but still believe it has anything to do with its time-out settings.

• None of my spreadsheets open on my mac but will open on other devices

  At random points in the numbers of time will not open one of my worksheets saved via the cloud.

  For the moment, they open on my phone, iPad and the macbook, but not on my imac

  Help

  What is the point of having a huge screen and a desktop computer if it does not open more simple spreadsheets that I used on the machine in the last two days. How should I do?

  HI Roger,

  Not enough information to give a definitive answer.

  Is the current version of the version (3 digits) numbers only you have already been installed on the Mac? (Can't even guess that, as you have sindou no information as to what model it is or the version of Mac OS X you have installed).

  If you have had Numbers ' 09 on this machine, it is probably still there, in a folder named iWork 09 in your Applications folder.

  If this is the case, one possible cause is that you try, whether intentionally or by accident, to open files in Numbers ' 09. Try to open the file by dragging the icon of 3 numbers on the platform and by the applicant on this icon. The icon number 3 is a bar chart with FOUR bars. Numbers ' 09 has a similar icon, but the bar graph has only 3 bars.

  Kind regards

  Barry

• Unable to find the device id / install app via command line after ios6

  After I updated my ipad to ios6 I don't think the device for IT id... IDB - devices do not return any found devices.  I can see the ipad in Explorer windows etc, but it is not detected and therefore I am unable to install my application...

  Everyone has the same problems?  Workaround solutions?

  Thank you

  Bobby

  Could you please check if the devices are discovered in your iTunes. If the devices are not detected in iTunes, then update iTunes to the latest version. I hope this will solve your problem.

• Lost Bluetooth after Windows 7 install. After an upgrade to windows 7. I was unable to find my device in Device Manager or my application software in the program menu.

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Install the latest driver for the Bluetooth compatible with Windows 7.

• LaserJet Pro M127fn Installer cannot find the device on the network

  Hello

  I just bought the product, but during the installation - setup is unable to find the device on the network. Device is properly registered to the address 192.168.0.14 (with static IP address), I can see the dashboard configiration at the same address via browser and all works well with the network itself.

  Try to ping the IP - it's ok. Tried to install without active firewall - also fails.

  Double checked the installation process - with automatic search and provide the IP address of the printer - both failed.

  Also, I rebooted the router and the switch and the computer. Is not new. I also tried downloading the last executable configuration on the site - and even once, it fails with 'device not found on the network.

  Then what do I do to fix this?

  Thank you

  Finally found a solution. It is strange as it may seem, but after all, it's a solution.

  -Rinse your DNS and your ARP cache (see the Google if you don't know what that means)

  -Reboot the router (or, where appropriate - switches)

  -Change the IP address of the device on your network. Try with round numbers like (192.168.0.20)

  -Restart your router (and if applicable - switches)

  -Restart your computer (s)

  -Don't run the Setup again and the hoprefully you will have no errors and everything works perfectly for you

  If your problem, similar to mine, persists, repeat the above process again and again... and again...

  Good luck

• WiFi limited connectivity (Win 7) when other devices connect correctly.

  I had problems with my wifi recently. When I start my computer it connects fine, but sometimes then shows limited connectivity when all other devices (my phone and Tablet) are connected properly. I disconnect and reconnect and it temporarily solves the problem, but its not resolved. Any ideas on how to take care of it?

  Hello

  Don't you worry about this unless you have found errors. If Yes see these threads (you can safely
  (ignore this question).

  http://social.answers.Microsoft.com/forums/en/w7network/thread/754c8f29-3a87-4E77-Babd-a69c8910e17e

  http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/05a8849e-89c1-4CC9-8004-f6d07a4fdf8b

  http://www.cableforum.co.UK/Board/34932105-post6.html

  ====================================

  A new Microsoft 6to4 map is created unexpectedly after restarting Windows 7 or Windows
  Server 2008 R2
  http://support.Microsoft.com/kb/980486

  How to disable certain Internet Protocol version 6 (IPv6) components in Windows Vista, Windows 7
  and Windows Server 2008
  http://support.Microsoft.com/kb/929852/en-us

  Response of Lionel Chen
  http://social.technet.Microsoft.com/forums/en-us/itprovistahardware/thread/3a503cdb-e61c-44BC-97c4-0b38b0e5f929/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• My Audio icon is suddenly missing from the taskbar. I looked at your answers and am unable to find the tab notification area. Does anyone have any other suggestions? Thank you

  I lost my audio icon - it has just disappeared.

  After having read and followed the steps suggested by other members, I am still unable to find the tab notification area. Are there any other suggestions?
  Thank you!

  Hello

  (1) you still hear sound from the computer even if the icon is missing from the notification area?

  Follow the links below and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows-Vista/show-or-hide-the-notification-area-system-tray

  System icons do not appear in the notification area in Windows Vista or Windows 7, you must restart the computer

  http://support.Microsoft.com/kb/945011/en-us

• Unable to find PDF printer after I installed Mac CS6 in my MacBook Air... Please help ~.

  Hello... Unable to find PDF printer after I installed Mac CS6 in my MacBook Air... I had CS4 (Windows) before, but it comes with the printer PDF ~ can anyone help? Thank you...

  What is done on the Mac, is to use the PDF button in the print dialog box, and then select SAVE it in ADOBE PDF drop-down choice. This is equivalent to printing to a postscript file and running through Adobe Distiller.

• BlackBerry Z10 unable to find contacts in the Contact application

  Hello

  I have been using BlackBerry Z10 for a year. I was very satisfied with the performance of the device. I am indeed! but do not know what happening sudenly I'm unable to find any contact which is already available in the contacts app (NOTE: I do not use 3rd party app to store my contacts)

  Software version: version of the OS installed is BB 10 OS 10.3.1.1779

  This is the setting I made on my device:

  Automatically merge Contcts - WE

  Sort contacts by name

  View the contact as -firstly, the last

  Show the accounts in the list of contacts:

  BBM contacts

  BBM contacts video

  LinkedIn

  Facebook

  Twitter

  Outlook.com

  Contacts from the SIM card

  BBLink

  Search using cloud is UNCHECKED.

  Please do the needful.

  Thank you

  Nishant

  Wait... you mean you installed an update of the OS? And after that, this behavior started? If Yes, then the most common thing to do after an update which translates questions is to perform a reload of the OS. Sometimes the update process have errors and others... with a reload often cure the problems.

  Official methods, which will be controlled as to what exact OS versions are available:

  • http://supportforums.BlackBerry.com/T5/BlackBerry-10-functions-and/how-to-reload-your-Blackberry10-O...

  Non-official methods, which are cleaner and allow you to choose a version of the OS that maybe your carrier (or anyone they control your offers) delays in approval:

  • http://supportforums.BlackBerry.com/T5/BlackBerry-10-OS-device-software/upgrading-OS10-devices-using...
  • http://forums.CrackBerry.com/BB10-leaked-beta-OS-f395/BB10-OS-archive-943672/

  Of course, before you start this, you want a good backup link, a manual copy of the memory of your device to your PC and complete documentation of your configuration (identification information of account, adding applications, configurations, etc.). Sometimes, restoring a backup returns unit corruption even, must be eliminated and reconfiguration from scratch can solve that.

  Good luck!

• How can I fix this "Setup was unable to find (or could not read) the language specific setup resource dll, unable to continue." Error if please restart and try again. » ?

  I'm trying to install Microsoft FreeLancer on Windows 7 64 bit Home Premium edition (according to WinVer: Version 6.1, build 6701, Service Pack 1).

  After inserting the DVD in the drive and run "Setup.exe", I am invited by the UAC to elevate permissions - who I am agreement - then the following error message appears: "Setup was unable to find (or could not read) the language specific setup resource dll, unable to continue." If please restart and try again. »

  The only valid technote, I found the issue was http://support.microsoft.com/kb/258496. The below is the list of the things that I tried after reading this technote - but no avail.

  • Of course, I tried to restart.
  • I checked the DVD is in good condition, even with regard to the attempts to install from the disc to a friend and even went up to compare the MD5 of all files on two DVDs, the checksums match.
  • I tried using the compatibility mode for XP, although according to the report of another user on the statements of the Windows Compatibility Center that this should not be necessary.
  • I ran a full "chkdsk" (i.e. one scheduled for after a reboot, rebooted) and chkdsk reported no error.
  • I deleted all files "di - use ' %TEMP%, immediately after the restart and before you run setup.exe.
  • I've looked at this the EMET tool had an exemption for 'setup.exe' and my tool anti-virus was disabled before installation.

  Everything I try seems to have no effect on the resolution of this problem.

  Can anyone suggest any possible causes of--and, ideally, solutions to-this issue?

  Kind regards

  Alex.

  ... "Step 1: perform the clean boot to verify if it's a software conflict matter. '...

  -Tried but not given to impact.

  ... "Step 2: System File Checker tool"...

  -Tried but not given to impact.

  ... "I would have you check the same DVD on another computer and check if it works. '...

  -The only other machine that I use Ubuntu. My other half uses only his Mac.

  I managed to work around this problem by using the following workaround solution:

  I installed Freelancer CD on a Windows XP virtual machine running in VMWare Workstation. I then moved the installation directory (C:\Program Files\FreeLancer) off the coast of the virtual machine on my Windows 7 computer in (C:\Program Files (x 86) \FreeLancer).

  The game seems to work fine as long as it is run with administrative privileges (that is, the freelancer.exe running). Without administrator rights, the games is never recorded. With them, they are registered under "C:\Program Files (x 86) \FreeLancer\EXE\Accts\SinglePlayer" successfully.

• VPN L2L: ASA5505-&gt; ASA5520, initiator of IKE unable to find policy

  Hello!

  Periodically, we are experiencing a problem with tunnel between 5505 and 5520 L2L

  Sometimes there is no 5505 LAN access to one of the LAN's 5520

  ex: ping from the inside interface (10.1.13.1) 5505 to 5520 (10.1.1.1) does not work

  5505:
  - cry isa his we can see the peer - it's OK

  -in Cree its pe ip itsnecessary there, but program is not increase and still no ping

  -all the other itsof the acl work properly

  5505 debugging:

  % ASA-3-713042: unable to find political initiator IKE: outside Intf, Src: 10.1.13.1, Dst: 10.1.1.1
  % ASA-3-313001: Denied ICMP type = 8, code = 0 to 10.1.1.1

  ACL on both sides is correct

  Erase isakmp his helps solve the problem

  p.s., asa 5505 has two ISP and two crypto cards with 5520

  This happens whenever your primary or secondary provider fails