Source monitor has horizontal lines along video

Similar Questions

• Satellite A300-1IL - monitor has white lines at the bottom

  Good evening

  about an hour, followed by my satellite a300 monitor has white lines at the bottom.
  I try to stop, change the resolution but i just turn on my laptop, the screen has this white line.

  It is a problem of monito'rs or videocar problem?

  Sorry for my ebglish

  Hello

  > It is a problem of monito'rs or videocar problem?
  It's easy to say; you need to connect the external monitor to the laptop and need to check if the same if possible lines on a second external display.

  If the lines were visible on the external monitor, so that the GPU fault is possible.
  Otherwise, it may be defective internal display.

  Welcome them

• HP Pavilion will not start, has horizontal lines on monitor - HP Pavilion Elite M9280a

  I tried to start my computer yesterday and I had a brief message 'Error in Vista' then - my computer would not respond.

  The monitor has just shown the colored horizonal lines.  Then, I rebooted the computer.

  Since then, I can't reboot my computer at all however, I can get into safe mode to connect but remain - lines horizinal who won't go away.  The icons are much larger in safe mode too.

  When I try to log in normally, the system will repair mode and finally displays the following message:

  ' Start can't fix computer automatically "I went to see the details of the problem and this will display:

  Signature of the problem

  The Startup Repair V2 problem event name

  Problem signature 01 Auto failover

  02 6.6.6000.16396.6.0.5001.18000

  6 03

  04 131074

  05 no cause root

  06 no cause root

  07 0

  2 08

  WRP 09 repair

  2 of 10

  6.06.000.0.00.256.1 OS version

  Locale 1033 ID

  I did start diagnostic tests and everything seems ok, but the computer doesn't not recogise my graphics video card.  The system, it shows the video card - VGA video controller - PCI Bus 2 - device 0, function 0.

  Can someone help me please!  Products listed below

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/KB/docDisplay?javax.portlet.begCache...

  Hello

  Technical page in your PC Watch: the Nvidia GeForce 8600 GT, or integrated graphics. You can check which graphic solution you have?

  You can see the desktop when it is in safe mode?

  Try the safe mode with networking enabled.

  A position that interests you, your Version of the OS (6.06.000.0.00.256.1) indicates you are running the original version of Vista. You must also upgrade Vista to Service Pack 2 (6.0.6002).

  If you can not download the drivers in safe mode with network, can you download the driver on another PC and save to disk?

  While in safe mode try to remove the possible corrupt driver using Control Panel, restart and see if Vista will load a generic graphics driver. Then, you should be able to download and install the appropriate driver.

  Jaco

• Always get horizontal lines on video during export to 720 x 480 AVI with "Deinterlace" turned on

  Professional Hello again fine,

  I use 6 first on a Windows 7 computer.

  I always get horizontal lines in my video during export to AVI 720 x 480, even with "Deinterlace" lit.

  I had a doubt on another thread and said robodog2 that it is interlaced with the lines of the file are not displayed when you use a selection of progressive export file...

  http://forums.Adobe.com/thread/852077

  So I found the box "Deinterlace" via "chronology of export > movie > settings > special treatment > Modify > deinterlace ', but if I have this box checked, I still have horizontal lines.

  Here are the screenshots of the same base video before importing them in at first for an effect reverse, and after I saved the resulting file 720 x 480 AVI... the final file appears with the same horizontal lines if yes or no deinterlacing is checked.

  Lines are more visible when viewing the video in Windows Media Player they appear in these screenshots below... the lines have in fact characteristics of edge in the public eye.  The lines look like an old used TV sometimes when the antenna was not getting good reception.  Also, I am saving successfully the "chronology of export > movie" path with different codecs (this is no longer a file generated from the preview, I was talking about in the previous thread on this)... so I'm sure all the parameters with this version and I get this result with three different codecs, with and without the "Deinterlace" checked... I had the same experience over and over yesterday evening while he was also working with another file.

  No one knows what is the cause?... Please see the pictures below

  Thank you

  digiday

  AVI file of front of record in first -own original 720 x 480, 30 frames per second

  

  After the backup in the first 6

  Horizontal lines showing in this first 6, 720 x 480, 30 fps AVI file

  

  Hi David,

  Yes, I finally solve this problem, based on a chance observation on another forum.  On another forum a guy once mentioned the setting ' NONE FRAME ' in the 'Record Options' in the dialog "Export movie" when I export my movie to an AVI file, as seen in my screen shot below.  Otherwise, I think that setting was failing to "FIRST FRAME ABOVE".

  For the most part, I was getting these terrible horizontal lines when I exported the graphic effects that I created with imported Photoshop layers in my film projects... in these kinds of exports that horizontal lines were much worse and more obvious that if I was just export a project with the actual video that I had imported in my project.

  But still, even with the imported video, as examples of images that I posted on this thread, even in this case I saw the horizontal lines.

  So one guy on another forum said something about "ANY FRAME" setting in my export dialog box.  It relates to something else about deinterlacing it is better for this problem as the "FIRST FRAME SUPERIOR" or "FIRST FRAME BELOW" settings.

  As can be seen in my screenshot below, which is the setting I talk, but I was using the old 6 first of 1999all about, and options in the new versions of first export dialog are different.  The guy on the other forum that mentions that setting, that eventually solved my problem, said that the adjustment did not differ in a newer version of first he used, but I found this setting in my dialog "Export movie" , and that solved the problem.

  It was so simple and I went by so many things to try to solve it, including my files running through other apps to try to pre empt the problem and none of it worked... He just turns out to be THAT simple adjustment "ANY FIELD" and that solved the whole problem.

  First 6 and some newer versions of first, seem to have other problems, such as the creation of an oblong shape, rotation image from a round graph-shaped eggs after importation and applying an effect of rotation, but otherwise, once I realized that the solution of horizontal lines, I did pretty well understand many things in this former first and I got pretty good results.

  Viel Glück!

  

• my monitor has fuzzy LINES running left to right on the screen. How can I fix?

  software problems

  I would update the drivers, firmware or software for your monitor and your video at the same time card.  Also, if you have another monitor, swap them to see if the problem goes away or moves - then we can pretty much reduce the question to the screen and not the video card (and if the updated drivers do not resolve this problem, then it's a hardware problem and you can either take a workshop of computer service repair or simply a replacement of purchase screen.)  Do the same with the video card if you happen to have a spare part that fits.  If this isn't the case, you may need to take the system to a repair facility of computer for the service that it sounds like a hardware problem and not a software problem.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• OfficeJet Pro 8600 + magenta has horizontal lines

  I tried all that I know the difficulty the magenta - clean printhead, cartridges of change - but not better.  Called HP Support and they kept trying to sell me products to solve the problem.  This was initially a firewall, then it was a Mac tech.  They addressed everything except the printer.  Can someone help with this problem printhead/magenta?

  A get a new print head. First time in its history. Now I see that my 8600 more is assessed with poor print quality. Too bad because I love everything he does.

• The mobile version of my site has horizontal lines in the background on 3 pages. No idea why?

  

  http://siegelroofing.com/phone/estimate.html

  http://siegelroofing.com/phone/about-us.html

  http://siegelroofing.com/phone/Gallery.html
  

  This only happens when I push the changes to the site online not siegelroofing.businesscatalyst.com or even the part about muse.

  Hello

  Please refer to the suggestions mentioned here:

  http://forums.Adobe.com/message/6074353#6074353

  Thank you

  Sanjit

• HP OfficeJet Pro 6978: Horizontal lines in printing photos on paper photo with HP OfficeJet Pro 6978

  I bought a HP OfficeJet Pro 6978 today and implemented according to the instructions.  I loaded with premium photo paper more HP and proceeded to print a photo from my Mac.  As he came on the printer it has horizontal lines there.  I read somewhere on the forum that it could be a software problem, so I went to my computer to Microsoft and tried to print the same image using OS 7 and the results are the same.

  After reading some of these other forums, I pulled the plug and has waited a few minutes and plugged back in and the problem was solved!

• Horizontal lines in the saved preview AVI file

  Hi all

  On another thread, I was wondering why I was getting an error message when you try to export and save a movie, but now I was able to get a temp AVI file after hitting enter and save a file preview, but this AVI file preview, which is normally the same quality of the full saved file I think, has horizontal lines in it that are very obvious compared to the original file... below are the screenshots yet sample to compare...

  File Clean original AVI 720 x 480 30 fps

  

  Display of the lines in this file first 720 x 480 30 fps AVI preview

  

  I have a file imported into the script and she will play opposite via setting the speed being set to-100 and it reads in the preview window properly, in reverse, when I click on the play button.

  But when I do a "file > export timeline > film ' command I get an error message saying ' year error occurred while doing this film.» Error writing files (disk full)? " ... but my hard drive is nearly full, with more than 30 concerts left open on it... and my gadget to use RAM shows that more than half of my RAM capacity is not used.

  But I got a temp Preview file generated after knocking entered to play the preview after I was not able to save and that ' s how I got this file... and I think that the temporary files are normally just as strong as the final saved files because they take so much time to generate during the preview by pressing on enter as they do when you export and save.

  In addition, this process saved an AVI file of 8.5 gigabytes of file 1.5 MB AVI using the codec in CamStudio.

  
  

  Another test using the MSU lossless codec produces a 3.5 GB AVI file which seemed better, but wouldn't you just play faster than about one frame per second after an hour and a half to save time.

  Someone at - it solutions?... I see also that the new record of first shows a large screen size, but it was recorded at the same size of 720 x 480, as the original was.

  Thank you

  NuMetro

  The hard drive uses a swap file, and the program creates files (such as the rendered file you use now instead of an export file) and in general, if you get the message that the disk is full, chances are that your disk becomes too full for the program continues.  You must check your hard drive with care and make sure you have enough space to work without this message.  There are discussions here on how to configure your hardware to the good editing (forum hardware).

  The horizontal lines you see are "interlaced" lines... rather than being a "progressive"... file You can use mediainfo or gspot to see what your assets are exactly and then implement the project should match the one... and then export to match THAT... and you should be OK (once solve you the problem of hard disk)

• Portege M800 - horizontal lines on external monitor

  I just bought a number of new M800 (model number - PPM81A-06L01J) and all have second screens connected.

  On all secondary monitors, there are wavy horizontal lines. Secondary monitors are all of different sizes and different brand and model. They are all also on their native resolution and refresh rate. I also got the latest video drivers installed. Any body have an idea as to why this is and how to fix it?

  See you soon

  Brad

  Hello!

  I n t have a Portege M800, but on my Portege M700 I had some problems with the external monitor connected too.
  Here's the story about this:

  I connected the new external monitor for Portege M700 directly with an old VGA cable. Usually it t wasn't a problem for me but I was not satisfied with the quality of the image on the external monitor (a bit blurry) so I started to update the display driver and the BIOS of my Portege M700 but without success.
  Anyway, I tried a bit with Google and here in the forum and I decided to buy a new high-quality VGA cable. I exchanged the cable and what happens? Perfect image quality!

  As you can see, you should always use high quality new cables. Also, make sure that you use the highest screen resolution of the external display (native screen resolution) and set the refresh rate of the screen at 60 Hz.

  Good bye

• My monitor has started to Flash a few days ago... now it's for most of the colored lines.

  My monitor has started to Flash a few days ago... now that's for most of the colored lines... I updated the NVIDIA drivers for the NVIDIA Geforce 8400GS from NVIDIA site and it improved for a while, but now he's back. I got tired of another working monitor and the same thing happened so I think that this has to do with the video card.  Help, please.

  HP Pavilion a6130n

  Windows 7 Professional

  3 GB RAM

  400 GB HD

  NVIDIA Gefroce 8400GS

  It worked!  Thanks a lot to vnyga and old_geekster.

• Source monitor and program monitor not video playback

  The last time I used the first Pro CC has 8 Oct and the program worked fine. As of today, I have opened the project file and the source monitor and program is nothing display respectively. However, the audio playback for both are not affected. I tried to do a completely new project with different video and I get the same error. I restarted the first, restarted the computer and reinstalled first. No help. :/

  First CC Version: 8.1.0

  Computer information:

  Model name: Mac Pro

  Model identifier: MacPro5, 1

  Processor name: Intel Quad - Core Xeon

  Processor speed: 2.4 GHz

  Number of processors: 2

  Total number of cores: 8

  (By heart) L2 Cache: 256 KB

  L3 Cache (per CPU): 12 MB

  Memory: 16 GB

  Graphics ATI Radeon HD 5770 1024 MB

  Processor speed of interconnection: 5.86 GT/s

  Boot ROM version: MP51.007F.B03

  Version of the SCM (System): 1.39f11

  Version of the SMC (processor board): 1.39f11

  Serial number (System): H00470SREUH

  Serial number (processor board): J504301VJBH8B

  Material UUID: 4D6175EA-3353-5E84-BCA0-42A013A69BED

  Hello

  Please go to file > Project Settings > General and change the video rendering to the GPU acceleration software only provider and see if that helps.

  Thank you

  Regalo

• Why is different my sound in my time line of my Source monitor

  The volume becomes less or not that does not exist for a certain number of frames in the 2 clips in my video. When I drag my video clip in the source monitor in my time line, the sound is very good in my source monitor.  However, the sound becomes much lower for a few frames or completlely grave when I drag above the timeline. This happens for only a few pictures in 2 clips. When I tried to correct it at the hearing, the audio clip plays well in hearing, but is still at a lower/non-existent volume in the timeline panel. Frequency distribution said it should play correctly, but it isn't. Anyone experience this situation and know how to fix?

  Plug... Windows 7 64-bit. processor Intel core Quad CPU Q9400 2 .66GHz; 8 GB of ram; Graphics AMD Radeon HD 6800 Series card

  Looks like you have some keyrfames set track volume.  Only the strange law of clip if you move it to another location?  Clips act weird if you transfer to this place?

• Horizontal lines in any type of video file exported into Elements 9

  I spent 4 to 9 items items for my video production, and I have not been able to get rid of the horizontal lines in ANY type of file or with any setting.  I tried everything I read so far on these forums.

  Many comments say that export to WMV is the problem, but I export hundreds of videos to WMV with 4 items on my computer XP 32-bit.

  That or XP 32 bit on my new super powerful computer to Windows 7 64 - bit, Elements 9 makes lines with movement. The screenshot shows a typical example.  Butterflies as lines of flight and the edge of a tree, as I panned, possesses a shading along he made many lines.

  I was never really happy with first elements WMVs. I usually have a Premiere Elements, DV - AVI output and then use Windows MovieMaker to create a really nice WMV.

  But here are some options:

  When you go to computer/share/WMV, try clicking on the Advanced button and,.

  In the advanced settings, go to the video tab, and then assign the Codec Windows Media Player 9 Advanced Profile. (You will be prompted to save a new preset when you click OK - so you can reuse it any time that). See if that makes a difference.

  If not, there other things you can do for the DeInterlace your video on your timeline - but you shouldn't need to do this.

  Or you can use my method. Windows MovieMaker is much cleaner WMVs!

• Strange horizontal lines on the 2nd monitor (TecS1 + ATI) multiscreen mode

  Hello

  I have a kind of a strange question when I'm working in mode multi-display with a Compaq 9500 19 "monitor as a second monitor attached. When resizing of content, a large number of strange horizontal lines, some short, some long, (in fact quite random) appear spread out on the full screen.

  It seems that the graphics card ATI Mobility Radeon graphics buffer is corrupted somehow, I can still work, but it's still annoying. I have to say that this problem seems to appear only on Windows Server 2003, not when I run the Tecra S1 under XP (installed as multiboot). So, it might be a driver ATI - OS incompatibility.

  Any help would be much appreciated.

  Thank you
  Mark

  Hi Mark

  In my opinion, you are absolutely right. It's probably the driver ATI - OS incompatibility. All drivers are adapted to work properly with the operating system supplied with the notebook. Windows Server 2003 is not supported by Toshiba and I think it will be the problem to solve this problem.