SourceFire updates

Similar Questions

• SourceFire - update Virtual Center of defence 6.0.0 Installation failed

  Hello

  I get the following error when applies the 6.0.0 - Sourcefire_3D_Defense_Center_S3_Upgrade - 1005.sh

  Update Installation Failed: [% 1] Fatal error: error running script 000_start/003_check_DC_memory.pl

  Any resolution will appreciate

  Thank you.

  Hello

  This script verifies the memory available to the centre of defence to use, and 6.0.0 requires a minimum of 6 GB of memory, an increase from 5.x versions.

  -Stop of the DC gracefully from the CLI or WebUI

  -In vSphere, right-click on the domain controller, select change settings.

  -Adjust the Configuration to allow a minimum of 6 GB to the device and save the memory settings

  -Turn on the DC back and resume the update.

  Thank you

  Guillaume

• SourceFire IPS updates

  We are developing a new firewall with IPS SFP modules in them that will be managed by an application of SourceFire Security Center (1500 series)

  I know with the old IPS systems, modules would get their updates of signature directly. Now they get their updates of software and signature of the Management Server? (this would make things a lot easier)

  Hello Colin

  Yes, your Firesight Management Center Gets all the updates rules and Intrusion policies get updated and redeployed to your probes.

  HTH

  Paul

• Failure to download sourcefire intelligence feed

  I have a Cisco's Firesight device that gets the following error

  Received Soucefire_Intelligence_Feed code (impossible to download the file)

  Since the update system to 5.4.1.8

  I went through all the troubleshooting steps described in this document

  http://www.Cisco.com/c/en/us/support/docs/security/firesight-management-...

  and everything seems in good condition. No problem to set intelligence.sourcefire.com or do a curl command, etc.

  Firewall is open to this host (nothing has changed it)

  Does anyone else have this problem? What is going on?

  I had this problem as well. I opened a case of TAC with Cisco and they said it's a new bug (CSCvb70107). It was Wednesday, October 12, 2016. I received today a power update without making any changes on my system.

  Problem with hosting power of security intelligence.

• Upgrade to version 6.0 SourceFire Module questions

  We have just implemented SourceFire Module version 5.4.1 on our ASA recently, but want to upgrade to version 6.0. I've been through Notes version 6.0 for the upgrade, which are dated to November 2015, but had a few questions that I was hoping someone here could answer:

  -Our FireSIGHT Management Center is a virtual appliance of 64-bit. Can we install version 6.0 on a virtual appliance VMWare running on EXSi 6.0? The only issue date list 5.1 and 5.5 ESXi ESXi.

  -Should what files I use for the update? The Release Notes say to use "SourceFire_3d_Defense_Center_S3_upgrade - 6.0.0 - 1005.sh. My choice on Cisco's Support site are: asasfr-sys - 6.0.0 - 1005.pkg, asasfr-5500 x-boot - 6.0.0 - 1005.img and Cisco_Network_Sensor_Upgrade - 6.0.0 - 1005.sh. I guess the sys-asasfr - 1005.pkg - 6.0.0 is for CME, and the Cisco_Network_Sensor_Upgrade - 6.0.0 - 1005.sh is for the ASAs.Is that right?

  -How long will the update for FMC and ASAs? The ASA is a 5516 x and the release notes look like they say that the update will take about 41 minutes.

  ESXi 6.0 is not officially supported so that your experience may vary. If you get stuck, you may TAC by telling you that you're on your own.

  "Cisco_Network_Sensor_Upgrade - 6.0.0 - 1005.sh" is used to upgrade the fire ASA power module in the Manager of firepower.

  If you were a fabricated construction or reimage then you would use the boot images and sys respectively.

  41 minutes for CME is right. As mentioned Philip, 2 hours is a better estimate of the ASA module, especially on a smaller area as the X 5516.

• Update module power of fire ASA 5.4.0

  Hi all

  It looks like Cisco released version 5.4 SourceFire for ASA a few days ago. We Commission a new ASA firewall with SFR module and I would have updated to the latest version before that he go to the prod, more 5.4 seems to have SSL decryption features that are not available in point 5.3.

  I can download updates to the center of the defense (5.4.0 and 5.4.0.1), but when I go to Downloads\NextGen firewalls\ASA with SFR etc, I can only see the 5.4.0.1 patch (file .sh) but nothing like it 5.4.0. I don't know how real works upgrade module SFR, but assuming it's the same process as the DC updates are not noncommutative.

  I tried to download the update of the SFR 5.4.0.1 module to DC but he said: there is no compatible devices found, and that the update is scheduled for 5.4.0+. Of course my modules are still running 5.3.

  Is it just me or is missing required update in the download area on Cisco.com?

  Appreciate all the information.
  Stan.

  Download it here

  http://uploads.Sourcefire.com/download/0642eee330b34f40adb63efed43198d6/20150222012033-Cisco_Network_Sensor_Upgrade-5.4.0-763.sh

  Transfer to firesight then install, then install the patch

• Sourcefire 3D appliance S3 upgrade 5.3.0.8 to 5.4.0.

  Hello! Try to update to the newer version on my sensor.

  As a first step, I try to update the system-updates, but I see that "no new updates available"

  Ok! I downloaded Sourcefire 3D appliance S3 upgrade (version 5.4.0 - 763) and publish updade Center.

  After this test to install the update. ([7%] running script 000_start/111_FS_integrity_check.sh...) After that, I got error.

  I have version of the sensor - 5.3.0.8, may be I have to install another version (not 5.4.0.)? Thank you!

  Hello team,

  The upgrade looks like a failed in the FS integrity check error. It will be the same error even if you install 5.4.0 without solving the problem.

  Could you please try to run the following command and restart the upgrade.

  Connection to the CLI of the device that is having the problem to upgrade.

  Raise to the root user and run the following command: -.

  Touch .skip_fsic

  Rate if this is useful.

  Concerning
  Jetsy

• Update S160 physical to virtual.

  We have a webfilter S160 and I was playing around to update because the performance is subpar after Async 8 outputs.  We got the price to upgrade to a S170 or S380 but the rep adds that we can use virtual appliances for free.  We already have a nice vmware infrastructure in place, so I have a few questions on this.

  How do you manage the interface monitoring L4 in the virtual world?

  I found the downloads for the virtual appliance, but there are three versions.  That are needed?

  S000V, S100V, S300V?  No reason not to go to the S300V so it is the best?

  Yes, for the moment, although I'll probably go with something else for L4...  (Snort and Sourcefire...)

  We smartnet material and you pay your license fee, just like usual.  Deploy 1000 vms, they don't care, as long as you are only serving many users covers your license, you good to go.

  You jump through the hoops on the site of license to obtain your license file and apply it to each virtual computer that you deploy.

• Update installation failed: [0%] fatal error running script 000_start 001_check_models.pl

  try to upgrade to a fire power (formerly sourcefire) DC750 to 6.0.0.0...

  ram upgrade

  5.4.1.6 running

  Get the following error shortly after the beginning of the upgrade.

  Update installation failed: [0%] fatal error running script 000_start 001_check_models.pl

  Hello

  This indicates that the version of the software that you use may not be for this model.

  If you use any sensor series 2 old on this domain controller, which would need to be removed.

  Can you check software 6.0 again to make sure that its for DC 750 and also go in the repertoire/var/log/sf/6.0. Check the content of /000_start and then the tail 001_check_models.pl.log

  It will erase more log details.

  Rate if helps.

  Yogesh

• Sourcefire Defense Center Upgrade version (local installation) failed

  Hi team,

  I had a problem during the upgrade of our CME to 5.4.0.

  Alerts

  Task notification

  Task status of your version upgrade of defense Center S3 task installation Sourcefire 3D: 5.4.0 - 763 (local installation) failed in the sea 25 09:46:02 Nov 2015

  Could not update the State: DB connection has been lost prior: new loading database...

  Hi John,.

  This error appears rarely. It is a known issue: CSCze94563

  Reference: https://tools.cisco.com/bugsearch/bug/CSCze94563/?reffering_site=dumpcr

  I just edited the bug to contain more information. It may take some time to reflect it.

  The task status page can present the error above, however, the help > on of interface user page indicating that the system in question is running version 5.4

  You can also view the logs to confirm this.

  Cat/var/log/sf /<5.4_upgrade_directory>main_upgrade_script.log

  The last line should read "success, removed the upgrade lock.

  Thank you

  Guillaume

• Update failed geolocation

  Hello

  Under the status of the task that I see

  installation of Sourcefire Geolocation Database Update version: GeoDB-2015-07-18-001 Local installation     Need to know why this update fails?   Concerning   Mahesh

  Cannot install the update of geolocation. Please contact the support of Sourcefire.

  What do you get if you check the following:

  https://support.sourcefire.com/auto-update/auto-dl.cgi/<> key>/GetCurrent/sf.xml license

  If you go back and do an update initiated by the user now it work?

  If it continues to fail, your best option is probably to contact the TAC. They can quickly break into newspapers in the file system to see exactly what is happening.

• FMC will recognize not update version 6.0.1 - 1214

  Hi all

  In light of reviews cisco-sa-20160330-fp (CVE-2016-1345), an attempt to upgrade 6.0.1 build CME - 1213 build 6.0.1 - 1214 is not recognized.

  First attempt was to let FMC detect/download the update, but this resulted in the following message if poster "no new update currently available."

  Second attempt involved manually download the update (6.0.1 - Sourcefire_3D_Defense_Center_S3_Upgrade - 1214.sh) file of the site Web of Cisco and the Uploader on CMF and then try to install it. This resulted in the following message not "valid devices available for Sourcefire Defense Center S3 upgrade 6.0.1 3D - 1214." This update is intended for software versions higher or equal to 6.0.0 and less 6.0.1 - 1214. »

  This updated version 6.0.1 - 1214 is required to install the recent hotfix (Sourcefire_3D_Defense_Center_S3_Hotfix - 6.0.1.1 - 4. short), as shown in the download software page.

  Someone facing similar problems? All possible solutions?

  Thank you.

  MP

  Looks like they took this package on the download site.

  The fix for the CMF is however is displayed with a date of April 1, 2016:

  https://software.Cisco.com/download/release.html?mdfid=286259687&RelType...

  I was able to download and install successfully on my 6.0.1 - 1213 version virtual CMF.

  firepower_hotfix_success.PNG

  

• Since update 10.0.2 at 6s "trash all ' in the Inbox.

  Since I did the update (10.0.2) I can no longer just "trash all ' mail inbox (Verizon).  Because I get emails 300 + a day, I need to be able to empty my Inbox easily without deleting all of them individually.  It is very irritating and time consuming.

  Anyway around this?  Thank you...

  sharikay wrote:

  Anyway around this?  Thank you...

  Not at the moment. Tell Apple you want to come back.

  http://www.Apple.com/feedback/iPhone.html

• Uninstall software update Apple says error in seller contact package package unstaller

  Try to get itunes working to make a backup of my faulty iphone before repair.

  First-itunes does not start says error. I'm trying to fix it, who said success but same error when you try to start it.

  Then uninstall completely worked. Then reinstall that seemed to be over except for a message "an older version of Apple software update already exists" then he went down and install itunes apparently had not been completed.

  Then I try to remove the update from the apple software and executed by an error in the installation program - it says there is an error in the installation and contact the supplier of the installation package. Same error if I run the uninstall command line program.

  Try to repair the Apple Software Update of programs & features Control Panel and then try to update iTunes again.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  The more information box has direct links with the current and recent if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit - for older video cards) as a workaround for problems with installation or operation, or compatibility with third-party software.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Since the update for Sierra, contacts do not appear in Messages - just phone numbers.

  Since the update for Sierra, Messages no longer displays Contact names - only phone numbers.  No instructions on how to remedy this.  Ideas?

  Hello

  Go into the Contacts application and ensure that it uses the same account synchronization like the iPhone and other devices you may be using.

  Also check the part of the accounts of the Contacts application preferences and make sure that it's only using one account.

  

  21:34 on Friday. 7 October 2016

   iMac 2.5 Ghz i5 2011 (El Capitan)
   G4/1GhzDual MDD (Leopard 10.5.8)
   MacBookPro (Snow Leopard 10.6.8) 2 GB
   Mac OS X (10.6.8).
   iPhone and iPad (2)