Special pool of memory detected corrupt ntoskrnl.exe

Similar Questions

• Configuring updates... Missing or corrupt NTOSKRNL.exe

  Hello

  I have a sony VGN NR260E, (Windows Vista Home Premium) recently on power, windows entered the dreaded

  Configuring updates 1 3 mode...
  She was followed by a reboot that caused the error

  Windows boot manager cannot start Windows...
  File ntoskrnl.exe
  Status: 0xc0000098
  Info: windows could not load because a required file is missing or damaged

  So, fortunately I have a recovery disk and I did a recovery to a previous restore point - and windows came fine. Since then, I have disabled the Windows updates

  The problem is in the power down and turn on the system back in the
  Configuration of updates (followed by a ntoskrnl.exe error restart failure) mode

  The result is that
  1. I cannot turn off without going through this lengthy procedure
  2. I can't get updates

  So, how to stop windows from "reflection", there is somehting to configure (new can't power upward).

  I also tried the fix Windows6. 0-KB937287-v2 - x 86, but when I run it it says it isn't neceassry (or something similar) on my system

  Please help because it is originally no end of grief

  Thank you

  Hello

  Yes it shouldn't affect other updates, however this never caused that it could.

  Good idea to run these just in case where after any hotfix:

  Try these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ---------------------------------------

  So don't forget to run these two:

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Description of the system update for Windows Vista, for Windows Server 2008 analytical tool, for
  Windows Server 2008 R2 Release Candidate for Windows 7 Release candidate
  http://support.Microsoft.com/kb/947821

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Vista sp1 corrupts ntoskrnl.exe

  Installed Windows Vista Home Premium 32 BIT of Dell supplied DVD of resettlement on new Western Digital HDD (1 TB green SATA600 HD 64 MB) in replacement of primary transmission single partition in Dell XPS 410 with 4 GB of RAM.  Tried to update with Windows Vista Service Pac 1, downloaded from the site Microsoft Web (http://windows.microsoft.com/en-US/windows/downloads/service-packs).  Both times I tried to perform the update the following appeared on the screen: "cannot start Windows.  A recent hardware or software change might be the cause.  To solve problem 1. Insert your Windows installation disc, and then restart your computer. 2. choose your language settings, and then click Next.  3. click on repair computer.  File: ntoskrnl.exe; status 0xc0000098; Info: Windows failed to load because a required file is damaged. "Completing steps 1 to 3 following the startup repair products:"Startup Repair cannot repair this computer automatically"and the details of the repair diagnosis says"C:\ntoskrnl.exe is corrupt ".  I had to do a system restore to before I tried the update for the restart of the computer.  Any idea what the problem might be with the installation of SP1?

  .. .are say you my best plan (perhaps only) action is to reformat the hard drive and upgrade to Windows 7?

  Assuming that the computer passes Win7 Upgrade Advisor with flying colors, you can format the HARD drive and then do a clean install of Win7 (which would need to buy a commercial full version of Win7) but you can not upgrade to Win7 computer (using a version upgrade from Win7) unless Vista SP1 is installed.

  Otherwise, the best solution would be to be formatting the HARD drive and then do a clean install of Vista exactly by the (my) message of reply in this thread: http://answers.microsoft.com/thread/c44429fb-3f7c-4646-8529-5a97bb3cd0eb

  Note: The computer must NOT be connected to the internet or local networks (i.e. other computers) in its current state. All your personal data (e.g., banking online & passwords credit card) must be considered at risk, if not already compromised.

  Wish I had better news for you. Good luck!

• Satellite M70 151: message: not found or corrupt ntoskrnl.exe

  Hello

  Since I am not native English, I try to explain my problem as exactly as possible:

  I've used this laptop for XP Prof. two days there are about 1 1/2 years, I did my full weekly
  all partitions with acronis true image backup.

  Yesterday, I had the following problem:
  BIOS showed RAM, HDD etc work, and then I thought: 'not found ntoskrnl.exe or damaged, please install '.
  a new copy"wow...

  The same in safe mode. My acronis rescue cd didn't start, a knoppix and linux cd does not start.
  and even trying to boot from my XP cd: 'error in txtsetp.sif, cannot continue. " BTW, all the
  CD dΘmarrez well on another xp laptop.

  Someone have an idea, or should I say goodbye to my laptop?

  Sincerely, Noelle

  [Edited by: admin]

  Hello

  might be possible that the RAM is faulty. Already tried a RAMtest with Memtest86? These things happen when the HARD or the RAM disk is defective. It sounds like a hardware problem, so I suggest you to bring your machine to an authorized service partner.
  Here is a link if you don t find a servicepartner:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT
  (Toshiba support - global ASP Locator)

  Welcome and good luck

• corrupt ntoskrnl.exe Vista configuration problem

  Windows Vista goes into an endless loop of updated Configuration, before he go to step 3, it will stop and restart with the message "Windows is loading files" then it trying to repair for 20 min, + manage to restore the system and return to the login screen. When I look at the log file, it states that the ntoskrnl.exe has been altered.

  I would really appreciate technical assistance to resolve this issue once and for all.  This problem seems to happen every now and then. Initially, I thought it was to do with Norton ISv10, but after the removal of this software, I still have the problem.

  Help please!

  mtang33,
  What version of Windows and level of service pack are you running?

  Take a look at this article as it can help with your problem.
  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Blue screen - ntoskrnl.exe was able to start: kernel missing/corrupted dxgkrnl.sys

  original title: BSOD and freezes, several errors reported, puzzled.

  Hello

  I've been struggling with trying to understand an intermittent problem for the last 3 weeks.  The problem has been around for one more month, but it seems to happen more and more often can't find the source.  I wish I could attach the dump files memory here, but don't see any option for this.  So here it goes...

  Have had this computer for 2-3 years and have not changed the material at all and only the drivers updated.

  CPU: Intel Core i7 CPU * address email is removed from the privacy *.

  Motherboard: ACPI x 64

  PowerSource: Power TX 750W.

  2 Hardrives: WDC - WD6401AALS-00L3B2 ATA

  6 GB OF RAM

  Graphics card: NVIDIA GeForce GTX 260

  I have wiped the two HD, reinstalled Vista.  I've updated the Vista completely.  I've updated the following drivers to their latest: graphics card, motherboard, map its (motherboard), LAN (motherboard).

  The computer crashes more often that the BSOD appears.  When it freezes, the sound plays all that was the last one on again and again and nothing does.  No data memory is dumped to the crash.  I checked with another computer that is on the network to see if she could still access shared files and that he could not.  It has frozen or gave the BSOD when just doing electronic-mail/surf net or playing dungeons and Online (DDO dragons).

  Challenges in a relationship with install/updates: SP2 would not install through normal updating, so a download and install manually.  DDO requires NET framework 1.1 to run.  Had to integrate the installation so that it can install.  Do not remember having to do in the past.  The point of freezing/BSOD is always the same before and after I did the complete wipe.

  Made the following stress tests:

  Don't use memtest 86 + (2.11 and version 4.10) x no errors, 8 longer past track.

  Used Furmark 1.8.2 V max stress test, ran all night without crashing.

  Used Video Card Stability Test (Group in stone), no problem.

  Used Seagate Diagnostics on HD, long and short no trials, no failure.

  Reported on BSOD errors:

  Ntoskrnl.exe could not start: missing/corrupted core

  dxgkrnl.sys

  driver_IRQL_NOT_LESS_OR_EQUAL nvlddmkm.sys

  More information on these if necessary.

  I get about 5 freezes with no info to each BSOD with info.  Very hard to debug with any info.

  I've had freezes/BSOD occur minutes after the computer starts and the hours.  Have the box to open with an external fan blowing into the case.  Don't think overheating is the problem.  No overclocking ever carried out on the system.

  I'm relearning all debugging stuff, did not have to do this in a long time any help would be very appreciated.

  Thanks in advance for your help.

  Hello

  If you do not remove ANY power and reconnect the cables (at both ends, memory and cards)
  When possible) - in fact, remove and replace - do not just tight.

  As you re-installed Vista twice the question must be something that works with a low level
  as the BIOS, chipset of low level drivers or hardware.

  You can validate files minidumps on the SkyDrive or other file sharing sites so that they can be
  downloaded, and we will have a look. But to be honest they will reveal probably material
  or worth nothing useful, so.

  Use SkyDrive download collected files and after shot/screenshot.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  -----------------------------------------------------------------------------

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  I hope this helps and happy holidays!

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• boot critical file c:\ntoskrnl.exe is corrupt

  Every time I do windows update and then restart, when it configures updates that does not have the login screen, then on my laptop restarts and goes to startup repair. She does every time after that the update and I think it restore my laptop to a working state, because sometimes my files are missing, although she said that no change will be to your files. I used registry booster and there was problems 226 rate was high. When I had repaired problems I installed service pack 1 manually since it wouldn't do it through windows update. When he was made to install the same thing happens again. The problem was boot critical file c:\ntoskrnl.exe is corrupt. From start of the repair, I looked for booster registry to see if he can repair the file, but for some reason it was not on my laptop.

  "Windows NT did not start... Ntoskrnl.exe error message.
  http://support.Microsoft.com/kb/124550

  http://search.Yahoo.com/search?p=Ntoskrnl.exe+is+corrupt&EI=UTF-8&FR=HP-PVDT

• "When restarting, get the error, Windows could not start because the following file is missing or corrupt: < root Windows > \system32\ntoskrnl.exe.

  Original title: black screen

  Attempt to restart the Gateway system running XP Pro.  The message "Windows has not start because the following file is missing or corrupt: \system32\ntoskrnl.exe" Please reinstall a copy of this file.  What do I do and where is this file?

  There is a good chance that the disk check running the Recovery Console will solve the problem.

  1. Insert the Windows XP CD in your CD-ROM drive and restart your computer. If you are prompted, select any options needed to start (boot) on the CD.
    
  2. when the text portion of Setup begins, follow the prompts. Select the repair or recovery option by pressing R.
    
  3. If you have a dual-boot or multiboot system, select the installation that you want to access from the Recovery Console.
    
  4. When you are prompted, type the administrator password. If you have not set a password for the account admin simply press on enter
    
  5. at the command prompt, type chkdsk/r > press ENTER. (Note: there is a space between the slash and the letter k).
    
  6. at the end of the output of scan type > press ENTER.
    
  7 restart your computer.

  If you do not have a Windows Xp disk, follow the instructions HERE to create a Windows Xp Recovery Console

• Ntoskrnl;. exe that is missing or corrupt file error

  I have a laptop with a ntoskrnl;. exe file that is missing or corrupted and cannot rebuild or load from cd, can I download this file somewhere, or what I can do to re - install this file and how?

  Hi WEBERSCHLOTZSKY,

  1. When you receive the error message?

  2. did you of recent changes on the computer?

  3. what happens when you try to copy the file from the Windows XP CD?

  There are several reasons for this error message to occur.

  This problem is often caused when the boot.ini file is missing or misconfigured. This problem often occurs when a user has recently added or removed from an operating system on the computer or added or deleted hard disk drives in the computer.

  If you are unable to start Windows and the error message then consult the below Microsoft article and try the steps mentioned, check if it helps.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  http://support.Microsoft.com/kb/314477

• Windows (Vista) can not start because the following file is missing or corrupt: < root windows > \system32\ntoskrnl.exe

  When I start windows, the message that I get a black screen is Windows (Vista) cannot start because the file is missing or corrupt: \system32\ntoskrnl.exe. Please reinstall a copy of the above file.

  I tried to launch a system of diagnosis without a disk and everything going on. I then tried running windows in safe mode and it won't allow me. That's when I switched to an installation disc supplied with the system. I tried to recover the system from there, but it would not go beyond the option of choosing an operating system. Once I got to that screen, there was NO operating system choose.

  I tried to restore my computer and there is no restore point.

  I renounced restore my computer and thought I'll all start over and install windows vista all over again. This was not the case either. I followed these steps:

  1. Turn on your computer and insert the CD or the DVD of Windows Vista.

  2. Install Windows page, follow all of the instructions that appear, and then clickInstall now.

  3. On the Get updated important for installation page, we recommend getting the latest updates to help ensure a successful installation and to help protect your computer against security threats. You will need an Internet connection to get the installation updates.

  4. On the Type your product key for activation page, we strongly recommend that you type your 25-character product key in order to avoid problems during activation.

  5. On the Please read the license terms page, if you agree to the terms of the license, clickI accepts the terms of the license.

  6. Follow the instructions on each page. On the type of installation do you want? page, clickCustom.

  7. On the place where you want to install Windows? page, select the partition where you want to install.

  8. Click next to begin the installation. You can see a compatibility report.

  and then had this error that says;

  windows doesn't have can create a partition on disk 0. The error occurred when preparing the partition selected for installation. Error code: 0x80004005.

  Now I am stuck and don't know what to do.

  Someone at - it solutions for me. Help, please.

  Hello

  1. on which the drive was initially installed OS?
  2. What partition you selected to install Windows?

  You can try to perform a startup repair by using the Vista installation disc.

  Check out these links for help:
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions  

  How can I fix a startup (startup)?
  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-fix-a-boot-startup-problem 

  What to do if Windows does not start correctly:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly 

  What are the system recovery options in Windows Vista?
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista 

  If nothing helps, so please get in touch with the system manufacturer for assistance because it may be a hardware problem.

  Kind regards
  Afzal Taher - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Ntoskrnl.exe seems to be corrupted on Vista Home Premium

  Computer has Vista Home Premium installed.  Moments ago, ntoskrnl.exe has begun abandon.  Now, he gives up all the time, which means from 1 to 10 minutes after the computer starts.  May be a corrupted file.  Is it possible to copy the program from another computer and replace the one that keeps giving?  Have you tried different avenues and the program seems to always work it cannot be superimposed.  A useful answer or point in the right direction would be most appreciated.

  Hello

  try a restore of the system before this happened

  http://www.windowsvistauserguide.com/system_restore.htm

  If necessary do in safe mode

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Dell PowerEdge T300 ntoskrnl.exe missing or corrupt [MS]

  Dell PowerEdge T300
  To: Win server 2003 32-bit st
  pOWEReDGE Expandable RAID Controller BIOS
  LSI 2007
  PERC 6 / i adapter
  6.0.3 - 0002 Pack FW

  It operating system starta no segnalando immediatamente di installare una copia del file ntoskrnl.exe

  Diagnostica no notes problemi hw

  It is properly Marin raid:

  1Protection drive found on the host adapter
  1 virtual drive managed by the BIOS

  Per ripristinare it Sop ho tried a con un disco di install di w2003 startare my non vede he raid e non ho a disposizione I driver (f6).

  Buongiorno,

  pilot of the it by it e perc6i controller he following:

  http://downloads.Dell.com/FOLDER97889M/10/DELL_MULTI-DEVICE_A07_R211422.exe

  Speaking saluti

  Manual

• Receive lots of BSOD due to ntoskrnl.exe, they stopped, but started again after a month

  I get lots of BSOD. I installed "WhoCrashed" and analyze the dump files. Here's what he said:

  Saturday, October 3, 14 17:29:30 GMT PM your computer crashed
  crash dump file: C:\Windows\Minidump\031014-15147-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0x75B80)
  Bugcheck code: 0x4E (0 x 0x2007E, 0 x 2, 0 20075, 99)
  Error: PFN_LIST_CORRUPT
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that the page frame number (PFN) list is corrupted.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem. This could be a case of corruption of memory. The corruption of memory more often happens because of software errors in the defective drivers buggy, not because of RAM modules.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  I have this problem for a long time. I've updated the drivers, windows updates, no effect. But, for some reason, he did not seem since February. But Monday, I used MiniCygwin_GOptimize_v1.34.02 to compress files apk android. He uses a lot of CPU. And after that the BSOD began to reappear. I downloaded the Minidump file and Information System if someone wants to check.

  Let me know the reason for these BSOD and how can I solve this problem.

  Hello

  We have many bug different controls:

  PFN_LIST_CORRUPT (4th)

  This indicates that the page frame number (PFN) list is corrupted.

  This error is usually caused by a driver passing a list of descriptor of bad memory. For example, the pilot could call MmUnlockPages twice with the same list.

  MEMORY_MANAGEMENT (1A)

  This indicates that an error occurred serious memory management.

  Error checking 1A, {5003, fffff780c0000000, 6933, 64ba0002d266}

  -1 setting of the bug check is 5003 which lists free work is corrupt. It is probably a hardware error.

  We also have another 1st parameter:

  Error checking 1 a, {fffff6800005cf40, eab00001beb34867,403, fffff6fc00df59a0}

  - Parameter 1 of the bug check is 403 which indicates the page table and NFPs are out of sync. It is also probably a clerical error.

  ^^ Pointed out that both of the above can still be caused by a driver causing corruption, but it is generally unlikely.

  And another...

  Error checking 1A, {41284, 159a0e001, 104 d 57, fffff70001080000}

  -1 setting of the bug check is 41284 indicating a PTE or the fixed work list is corrupted.

  BAD_POOL_HEADER (19)

  This indicates that a pool header is corrupt.

  Error checking 19, {20, fffff8a00b91df40, fffff8a00b91e020, 50e040c}

  6: kd >! pool fffff8a00b91df40
  Pool page fffff8a00b91df40 region is unknown
  fffff8a00b91d000 size: 4 d 0 previous size: 0 Ntff (allocated)
  fffff8a00b91d4d0 size: 30 size: 4 d 0 PfFK (allocated)
  fffff8a00b91d500 size: 30 size: 30 PfFK (allocated)
  fffff8a00b91d530 size: 10 previous size: 30 (free) NtfE
  fffff8a00b91d540 size: 30 size: 10 Ntf0 (allocated)
  fffff8a00b91d570 size: size previous 10:30 (free) Nbmc
  fffff8a00b91d580 size: 40 previous size: 10 DxgK (allocated)
  fffff8a00b91d5c0 size: c0 size previous: AfdX (protected) process (allocated) 40: fffffa801098c7f0
  fffff8a00b91d680 size: 170 previous size: c0 MPsc (allocated)
  fffff8a00b91d7f0 size: size previous c0: 170 FIcs (allocated)
  fffff8a00b91d8b0 size: 40 size: c0 (allocated) NtFs
  fffff8a00b91d8f0 size: 30 size: 40 (allocated) PfFK
  fffff8a00b91d920 size: 30 size: 30 Ntf0 (allocated)
  fffff8a00b91d950 size: 150 size: 30 FMfn (allocated)
  fffff8a00b91daa0 size: size 160: 150 FMfn (allocated)
  fffff8a00b91dc00 size: 40 size: 160 (allocated) MmSm
  fffff8a00b91dc40 size: c0 size previous: 40 FIcs (allocated)
  fffff8a00b91dd00 size: 10 size: c0 sect (free)
  fffff8a00b91dd10 size: 170 previous size: 10 MPsc (allocated)
  fffff8a00b91de80 size: size previous c0: 170 (allocated) NtFs
  * fffff8a00b91df40 size: size previous e0: c0 (free) * FIcs
          PoolTag FIcs: Context of FileInfo FS-Filter binary stream: fileinfo.sys

  ^^ Block of pool who looked in the page pool belongs to the context of FileInfo FS-Filter flow. This is related to the file system.

  6: kd >! poolval fffff8a00b91df40
  Pool page fffff8a00b91df40 region is unknown

  Validation of the headers of pool the pool page: fffff8a00b91df40

  [Fffff8a00b91d000] page pool is __inVALID.

  System_service_exception (3B)

  This indicates that an exception happened during execution of a routine that passes from non-preferred to the privileged code code.
  
  This error has been linked to the excessive use of expanded memory and resulting from user mode graphics drivers enjambment and passing data incorrect of the kernel code.

  2: kd > fffff960000a874f ln
  (fffff960'000 a 8720)   win32k! NextOwnedWindow + 0x2f |  (fffff960'000 a 8770) win32k! xxxRemoveDeleteMenuHelper

  ^^ The exception is produced in win32k! NextOwnedWindow.

  -----------------------

  Overall, this looks like the faulty RAM. It's not like there is a foul-smelling waters driver causing memory corruption here, but it is possible. The reason I mention this is because I see it in the crash dumps after dumping the! v

  OVERLAPPED_MODULE: Address overlap 'WinUsb' and 'ssudbus.sys'.

  ^^ WinUsb.sys - pilot class USB Windows system, it is a part of Windows. ssudbus.sys-

  SAMSUNG USB Composite Device Driver. Probably a part of Samsung Kies. Uninstall everything that you can find this topic.

  -----------------------

  Please run Memtest for NOT LESS than 8 ~ (several hours):

  Memtest86 +:

  Download Memtest86 + here:

  http://www.memtest.org/

  Which should I download?

  You can either download the ISO pre-built you want to burn to a CD and then boot from the CD, or you can download the automatic installer of the USB. What this will do is format your USB drive, make a boot device and then install the necessary files. Both do the same job, it's just you that you choose, or you have available (be it CD or USB).

  Note that some older generation motherboards do not support USB boot, your only option is CD (or floppy if you really wanted to).

  How Memtest works:

  Memtest86 writes a series of test patterns for most of the addresses of memory, reads the written data and compares it to find errors.

  The default pass is 9 different tests, varying in the modes of access and test data. A tenth test, bland, is selectable in the menu. He wrote all the memory with zeros, then sleeps 90 minutes before checking to see if the bits have changed (perhaps because of refresh problems). This is repeated with all those for a total time of 3 hours by pass.

  Many chipsets can report RAM speed and timings by SPD (Serial Presence Detect) or EPP (Enhanced Performance Profiles), and some even support changing the expected memory speed. If the expected memory speed is overclockee, Memtest86 can test that memory is free of error with these faster settings.

  Some hardware is able to report the status of the "PAT" (PAT: active or PAT: disabled). This is a reference to the Intel performance acceleration technology; There may be the BIOS settings that affect this aspect of memory synchronization.

  This information, if it is available for the program, can be displayed via a menu option.

  Other questions, they can most likely be answered by reading this excellent guide here:

  http://Forum.canardpc.com/threads/28864-FAQ-please-read-before-posting

  Kind regards

  Patrick

• Ntoskrnl.exe SYSTEM_SERVICE_EXCEPTION

  Hello

  I get BSOD at random times, and the use of blue screen I determined the problem with ntoskrnl.exe file. Although I had similar problems with dxgkrnl.sys. The problem is very annoying and can happen completely randomly.

  A problem has been detected and Windows has been shut down to avoid damage
  on your computer.

  The problem seems to be caused by the following file: ntoskrnl.exe

  SYSTEM_SERVICE_EXCEPTION

  If this is the first time you've seen this stop error screen,
  Restart your computer. If this screen appears again, follow
  the following steps:

  Check to make sure any new hardware or software is installed correctly.
  If this is a new installation, ask your hardware manufacturer or software
  the Windows updates, you might need.

  If problems continue, disable or remove any newly installed hardware
  or software. Disable the BIOS memory options such as implementing caching or shading.
  If you need to use safe mode to remove or disable components, restart
  your computer, press F8 to select Advanced Startup Options and then
  select Safe Mode.

  Technical information:

  STOP: 0X0000003B (0X00000000C0000005, 0XFFFFF80002507F4F, 0XFFFFFA600E2D30C0,
  0 x 0000000000000000)

  Ntoskrnl.exe - address 0xfffff800022a3450 base at 0xfffff80002249000 DateStamp
  0x4a7801eb

  Thanks for your help

  Luke

  Hello

  1. turn your Page file - change anything to the value if you plan to leave it like that (make a little
  (- reboot - largest) then go back and revert to the DEFAULT value.

  How to change the virtual memory paging file in Vista
  http://www.Vistax64.com/tutorials/132201-virtual-memory-paging-file-change.html

  2 do these to erase corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  3. update your video/display drivers manually using these methods.

  It's my generic how updates of appropriate driver: (you must manually update the video/display drivers)

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Stop: 0x000000d1 the problem seems to be caused by the following file: ntoskrnl.exe DRIVER_IRQL_NOT_LESS_OR_EQUAL

  I get the BSOD every once in a while during a variety of programs. I've updated all my drivers. I use bluescreenview watching dump files and that's what I have.

  A problem has been detected and Windows has been shut down to avoid damage
  on your computer.
  The problem seems to be caused by the following file: ntoskrnl.exe
  DRIVER_IRQL_NOT_LESS_OR_EQUAL
  If this is the first time you've seen this stop error screen,
  Restart your computer. If this screen appears again, follow
  the following steps:
  Check to make sure any new hardware or software is installed correctly.
  If this is a new installation, ask your hardware manufacturer or software
  the Windows updates, you might need.
  If problems continue, disable or remove any newly installed hardware
  or software. Disable the BIOS memory options such as implementing caching or shading.
  If you need to use safe mode to remove or disable components, restart
  your computer, press F8 to select Advanced Startup Options and then
  select Safe Mode.
  Technical information:
  STOP: 0X000000D1 (0XFFFFB880018FA1A0, 0 X 0000000000000002, 0 X 0000000000000008,
  0xffffb880018fa1a0)
  Ntoskrnl.exe - address 0xfffff800030dc1c0 base at 0xfffff8000305d000 DateStamp
  0x4fa390f3

  Hello

  Ntoskrnl.exe is a component of Windows which means than anything else he has led astray.

  BlueScreenView is a great tool for searching for information on minidumps. In particular
  the bottom panel where display the information on 3rd party drivers is useful. Of course
  other debuggers, such as WinDBG, might be able to glean information from minidumps.

  ------------------

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  For the methods of troubleshooting blue screen using BlueScreenView and MyEventViewer see my answers
  in this thread - top 3 RESPONSES (+ 1 other).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  ==============================================================

  BCCode: D1 0x000000D1

  Check these KB

  Stop error when you resume a computer that is running Windows 7 or Windows Server 2008 R2
  from sleep or standby extended: "STOP: 0x000000D1".
  http://support.Microsoft.com/kb/978982

  Stop error on a computer based on Windows Server 2008 R2 or Windows 7 during operation
  system uses a storport virtual miniport driver to save a dump file or a file of hibernation: "0x000000D1.
  http://support.Microsoft.com/kb/2320550

  Those 7 other KB Articles are available
  http://support.Microsoft.com/search/default.aspx?mode=a&query=0x000000D1&SPID=14019&catalog=LCID%3D1033&1033comm=1&Res=10

  --------------------------------------------------

  Think video drivers especially if it may be others. Refer to the section of driver in my credits
  methods of troubleshooting blue screen below. BIOS, chipset of low level drivers and
  antispyway/antivirus/security programs can also cause this. Check the resolution of the problems and
  When you arrive at the driver and tests of memory sections do reference to generic methods in following
  message and then back to the if necessary troubleshooting tool.

  Cause

  A driver tried to access a pageable (or that is completely invalid) address while the IRQL was too high.

  This bug check is usually caused by drivers who used a wrong address.

  If the first parameter has the same value as the fourth parameter, and the third parameter indicates a runtime operation, this bug check was probably caused by a driver who was trying to run code when the code itself has been paginated outside. The possible causes for the error page are:

  • The function was marked as pageable and was operating at an IRQL higher (including obtaining a lock).
  • The function call was made to a function in another pilot, and that this driver has been unloaded.
  • The function was called by using a function pointer that was an invalid pointer.

  
  BCCode: d1 0x000000d1<-- read="" this="">
  * 1210.html? order = votes http://www.faultwire.com/solutions-fatal_error/Driver-IRQL-not-less-or-Equal-0x000000D1-

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers to 7 (update drivers manually using the methods above is preferred
  to make sure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for the professional, full and Enterprise edition)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">