split 11i configuration

Similar Questions

• ASA 5505 Split Tunneling configured but still all traffic Tunneling

  Hello

  I installed an ASA 5505 running 8.3.2 and Cisco AnyConnect Client 2.5.2017.

  There are the DefaultRAGroup and a newly configured Group called SplitTunnelNets.

  I have 1 internal subnet (192.168.223.0/24) which has a matching ACL/AS configured on the DefaultRAGroup and the custom group policy called SSLClientPolicy.

  When I start the VPN with the ASA, I can indeed reach internal resources, but when I look at the routing table, I see a new default gateway route 0.0.0.0 / 0-> 192.168.25.2 (that is in the IP pool) with a metric of 2.  The default route before the start of the session AnyConnect now has a higher metric, so the 192.168.25.2 next hop is a priority.

  I don't see the routes in the routing table for 192.168.223.0/24 as I expect to see.  In the diagnosis of AnyConnect, I see that 0.0.0.0/0 is the policy applied to the client.

  Here's my setup.  Please tell me if you see something that I'm missing.

  ASA 8.3 Version (2)
  !
  host name asa

  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.223.254 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP x.x.x.x 255.255.255.240
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  boot system Disk0: / asa832 - k8.bin
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS lookup field inside
  DNS server-group DefaultDNS
  Server name 192.168.223.41
  domain Labs.com
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  vpn-client-net network object
  255.255.255.0 subnet 192.168.25.0
  network of the internal net object
  192.168.223.0 subnet 255.255.255.0
  the DM_INLINE_NETWORK_1 object-group network
  internal-net network object
  network-vpn-client-net object
  the DM_INLINE_NETWORK_2 object-group network
  internal-net network object
  network-vpn-client-net object
  SplitTunnelNets to access extensive ip list allow any 192.168.223.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  mask 192.168.25.1 - 192.168.25.50 255.255.255.0 IP local pool SSLClientPool
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ASDM image disk0: / asdm - 635.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (inside, all) static source internal-net net internal static destination vpn client vpn client-Net
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Labs-AAA protocol ldap LDAP-server
  AAA-server Lab-LDAP (inside) host 192.168.223.41
  Server-port 636
  LDAP-base-dn dc = labs, dc = com
  LDAP-scope subtree
  LDAP-naming-attribute sAMAccountName
  LDAP-login-password *.
  LDAP-connection-dn [email protected] / * /
  enable LDAP over ssl
  microsoft server type
  Enable http server
  http 192.168.223.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto ca trustpoint ASDM_TrustPoint0
  registration auto

  sslvpnkeypair key pair
  Configure CRL
  Crypto ca trustpoint ASDM_TrustPoint1
  ASDM_TrustPoint1 key pair
  Configure CRL
  string encryption ca ASDM_TrustPoint0 certificates

  Telnet 192.168.223.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 192.168.223.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  dhcpd outside auto_config
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP 192.5.41.41 Server
  NTP 192.5.41.40 Server
  SSL-trust outside ASDM_TrustPoint1 point
  WebVPN
  allow outside
  No anyconnect essentials
  SVC disk0:/anyconnect-win-2.5.2017-k9.pkg 1 image
  SVC disk0:/anyconnect-macosx-i386-3.0.0629-k9.pkg 2 image
  Picture disk0:/anyconnect-linux-3.0.0629-k9.pkg 3 SVC
  enable SVC
  tunnel-group-list activate
  internal SSLClientPolicy group strategy
  attributes of Group Policy SSLClientPolicy
  value of server DNS 192.168.223.41
  VPN-tunnel-Protocol svc
  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list SplitTunnelNets

  field default value Labs
  split dns value Labs.com
  the address value SSLClientPool pools
  WebVPN
  SVC Dungeon-Installer installed
  attributes of Group Policy DfltGrpPolicy
  value of server DNS 192.168.223.41
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list SplitTunnelNets
  coyotelabs.com value by default-field
  type of remote access service
  type tunnel-group SSLClientProfile remote access
  attributes global-tunnel-group SSLClientProfile
  CoyoteLabs-LDAP authentication-server-group
  Group Policy - by default-SSLClientPolicy
  tunnel-group SSLClientProfile webvpn-attributes
  allow group-alias CoyoteLabs
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:95b7ff58b54e02948a14b225eec1a990
  : end

  The split tunnel access list must be standard access-list, not extended access list.

  You must change the following:
  FROM: SplitTunnelNets access-list extended ip to allow all 192.168.223.0 255.255.255.0
  To: SplitTunnelNets standard access list allows 192.168.223.0 255.255.255.0

  You should be able to reconnect again and will be able to access the Internet after you set up the standard access-list split tunnel.

  Hope that helps.

• How can I return to a split-screen configuration?

  While I have is on a business trip, a colleague shared my computer and somehow changed the appearance of my Inbox a mode full-screen. I want to return to the split screen that allows me to see my emails and read the highlight in split-screen format, I had originally.

  Please keep your discussion on this topic. Do not PM me. Other people could benefit from the discussion.

  You say that pressing F8 does not turn on the message pane? You are in the main window with your Inbox showing right?

  In the Menu select View-Layout bar. Message pane is checked?

  No Menu bar? Press the ALT key.

  If it is checked, and still no message pane, maybe he dragged the bottom of the screen. Move your mouse down to the margin at the bottom of the screen and look for that to change in a double headed arrow. When it click and drag to the top to see if you can pull the top of the message pane.

• Oracle 11i - configuration of migration from development to production

  What is the recommended method to migrate the following configuration from development to production?
  automated tools? I tried Oracle planning, but I think it does not help much.
  
  (1) executable configuration
  (2) simultaneous program + configure settings of
  (3) updates of the application groups
  (4) fast code (all modules)
  (5) the profile options
  (6) files in the directory of the module (report oracle, sqlplus, etc.)

  First choice is FNDLOAD.
  See http://ioraclefusion.wordpress.com/2011/08/31/understanding-of-fndload-program/

  He's going to do a lot of what you're asking. The above link gives a good idea.

  For executables such as RDF, .sql etc. it is necessary to do it manually or use tools such as PVC.

  During the research, if planning has not worked for you, you will have to do it manually.

  Sandeep Gandhi

• Split mode configuration

  Hello

  Is it possible, on the split view, on the one hand to display code in a file and the other code in other files? So in the same window, I have two open files and can work with them.

  Of course, having two files open at the same time. Everyone is then able to be split Code view or Design view (or any other point of view that you want, such as Live View).

  Open your files (can be more than two!).

  Select the file that you want to appear on the left (go active by clicking on it).

  Do window > vertical mosaic if you're on a PC. There will be a similar command for Mac.

  If you have more than one open file, but I want to only work on the two files at once, you can then reduce the file you want to set aside. Do not close it, click the icon since that window and it will shrink down and allow you to organize the two windows open as you wish. Makes the active window that you want to appear on the left, and windows will reorganize in function, keep the reduced window minimized.

  To return all the display tabbed windows, just maximize any of them and they will increase all tabbed display.

• Split Tunneling does not

  I'm working on an installation of the laboratory program at home with my X-5506, and I got a split tunneling configuration problem.  Every change I seem to give me internet access, gives me access to the local network or remove both.  The current configuration, I took them both and I am a little puzzled.  I have attached the configuration.  Any guidance would be greatly appreciated!

  Change:

  split-tunnel-policy excludespecified

  TO:

  split-tunnel-policy tunnelspecified

  I notice you are using 192.168.0.0/24. Make sure that you do not work VPN'ing an address 192.168.0.0/24 as well (or a subnet that is also identical to your subnet that you are trying to access remotely) or it won't work. Overall, you should avoid using 10.0.0.0/24 and 192.168.0.0/24 in production networks because they are so frequently used in home networks. I also note that you have configured IKEv2. IKEv2 does not support split tunneling. SO be sure you use only the AnyConnect client in SSL mode.

• Cisco ASA ruled out a specific ip address of the split tunneling

  Hello

  I need help with a question on the split Tunneling Configuration.

  I have need exclude split tunneling networks already configured a specific ip address.

  This is my setup:

  Split_Tunnel list standard access allowed 192.168.0.0 255.255.0.0
  Split_Tunnel list standard access allowed 10.0.0.0 255.0.0.0

  attributes of Group Policy GroupPolicy_Anyconnect_Access_Exception_1
  WINS server no
  Server DNS value xxxxx xxxxxxx
  VPN - connections 3
  VPN-idle-timeout 480
  VPN-session-timeout no
  client ssl-VPN-tunnel-Protocol
  value of group-lock Anyconnect_access
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Split_Tunnel
  field default value xxxxx
  Split-dns value telefonica wh.telefonica cic.wh.telefonica telefonica.corp t380.inet
  mailar.telefonica.Corp mailar.telefonica.com tefgad.com telefonicaglobalsolutions.com
  telefonicabusinesssolutions.com

  I need to exclude the split tunnel, IP 10.0.0.50, my question is, if I change the list access deny this IP, the supplementary tunnel will exclude the period of INVESTIGATION.

  example:

  Split_Tunnel list standard access deny 10.0.0.50 255.255.255.255

  Split_Tunnel list standard access allowed 192.168.0.0 255.255.0.0
  Split_Tunnel list standard access allowed 10.0.0.0 255.0.0.0

  BR,

  Fidel Gonzalez

  Hi Fidel,

  Yes, it should work; as in your example deny 10.0.0.50/32 sholud exclude the traffic in the tunnel.

  I tried in my lab, and in my case, access-list is:

  split_1 list standard access denied the host 10.2.2.250
  split_1 list standard access allowed 10.2.2.0 255.255.255.0

  And it worked he excluded the 10.2.2.250 host.

  The screen shot of the AnyConnect added:

  capture.PNG

  

  Concerning

  Véronique

• access list of split tunneling

  Hello

  I have some problems on ASA 5520 split tunneling configuration.

  Here's the scenario:

  Number of remote users connects ipsec with ASA 5520 (in central) using ubuntu vpnc-client.

  Split tunneling is used, in order to allow remote users to surf the Internet using their ISP.

  The goal is to remove the possibility for ssh/telnet servers within the local enterprise network for remote users.

  Here is a part of the config:

  internal REMOTE_gp group strategy
  attributes of Group Policy REMOTE_gp
  VPN-idle-timeout no
  Protocol-tunnel-VPN IPSec
  Group-lock no
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list REMOTE_split

  tunnel-group type REMOTE access remotely

  tunnel-group REMOTE General attributes

  authentication-server-group RADIUSGR

  Group Policy - by default-REMOTE_gp

  REMOTE tunnel-group ipsec-attributes

  pre-shared-key *.

  ISAKMP keepalive retry threshold 15 10

  RADIUS protocol AAA-server RADIUSGR

  AAA-server RADIUSGR (INSIDE_LAN) 192.168.0.244

  REMOTE_split list extended access deny tcp 192.168.0.0 255.255.255.0 ssh telnet rank everything

  permit access ip 192.168.0.0 scope list REMOTE_split 255.255.255.0 192.168.100.0 255.255.255.0

  ip subnet ##192.168.100.0/24 - where from Radius Server to allocate ip addresses to remote users.

  INSIDE_LAN_in list extended access deny tcp 192.168.0.0 255.255.255.0 eq ssh 192.168.100.0 255.255.255.0

  INSIDE_LAN_in list extended access deny tcp 192.168.0.0 255.255.255.0 eq telnet 192.168.100.0 255.255.255.0

  permit access ip 192.168.0.0 scope list INSIDE_LAN_in 255.255.255.0 any

  It has nat enabled on the interface, but there is a special instruction in nat0 ACL for 192.168.100.0 subnet

  permit access ip 192.168.0.0 scope list INSIDE_LAN_nat0_outbound 255.255.255.0 192.168.100.0 255.255.255.0

  The problem is that the remote users can easily ssh and telnet servers in network INSIDE_LAN. Everything I put in INSIDE_LAN_in ACL, remote users still have full access to this network. Restrictions in the REMOTE_split ACL do not work either.

  You must configure vpn-filter rather to block telnet and ssh access as follows:

  Remote filter access list deny tcp 192.168.100.0 255.255.255.0 192.168.0.0 255.255.255.0 eq 22

  Remote filter access list deny tcp 192.168.100.0 255.255.255.0 192.168.0.0 255.255.255.0 eq 23

  distance-filter 192.168.100.0 ip access list allow 255.255.255.0 192.168.0.0 255.255.255.0

  attributes of Group Policy REMOTE_gp

  VPN-value filter-remote control

  Split tunnel acl has the following statement and it should be extended to standard ACLs instead of:

  REMOTE_split list of permitted access 192.168.0.0 255.255.255.0

  Hope that helps.

• Split tunneling issue

  Hi all

  What is the best way to install a split tunneling on a network, Cisco ASA 5510 I with cisco vpn client.

  Thank you

  This is the on the split tunneling configuration guide:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml

  Hope that helps.

• Split tunnel

  Hi guys,.

  I wonder if remote access VPN with split tunnel is using the home user or the corporate to surf internet connection own internet connection?

  Any help will be greatly appreciated.

  Thank you

  Lake

  Dear Lakeram,

  Split tunneling allows you to access certain resources through the tunnel and all other traffic will be sent to your local proxy.

  VPN traffic is defined by the VPN endpoint, for example:

  192.168.1.0/24---Internet---ADSL ASA VPN client-

  You can have the ASA push the network 192.168.1.0/24 to the customer. Once connected if the client tries to access everything that comes out of the scope of the network, this traffic will be sent to the LAN...

  Here's an example with ASA and router.

  ASA/PIX: Allow the tunneling split for the VPN Clients on the example of Configuration of ASA

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml

  ASA 8.x: allow the tunneling split for AnyConnect VPN Client on the example of Configuration of ASA

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080975e83.shtml

  Router allows the VPN Clients to connect to IPsec and Internet using Split Tunneling Configuration example

  http://www.Cisco.com/en/us/products/HW/routers/ps274/products_configuration_example09186a0080819289.shtml

  I hope it helps.

  Thank you.

• AnyConnect VPN and HP Office Jet Pro 8500 A910

  I can print from my laptop IBM T400 running Windows 7 64 bit. However, when I log in work AnyConnect VPN, I can't print. He says that the printer is disconnected from the network, even if it is connected. IT support at work said he can't change or adjust the VPN settings. The only way I can print is to disconnect from the VPN. Is this what I can adjust on the software of the printer or the printer itself?

  Hello

  To be able to print on the local network when you are connected to a network remote VPN might be possible by changing the VPN split tunneling configuration.

  However, it is depands on the VPN features and cannot be authorized because of the security requirements of your IT Department.

  Anyway, there is no way to configure such a thing by the printer or the printer software... It is directly affected by the configuration of the network and therefore require to modify VPN settings.

  Kind regards

  Shlomi

• AnyConnect VPN site to site fiber destined

  I'm installing AnyConnect in two places. There is a fiber point to point between the two locations, and they can communicate through it without any problem on the spot. I want to use AnyConnect to connect to A branch then also be able to access resources through the PTP Protocol to branch B. I tried some with split tunneling configuration changes, but nothing seems to be convey me. I have attached two ASA configs. Any help would be greatly appreciated!

  A: the 192.168.1.x site

  B: from the site 192.168.200.x

  On each ASA you need two lines below.  One for the local internal lan subnet and one for the remote lan subnet.  IN the case of the AESC, it must use the subnet VPN global (the address pool).

  nat (inside,outside) source static INTERNAL_SUBNET INTERNAL_SUBNET destination static VPN_SUBNET VPN_SUBNET

• Allow Inet access to VPN customers

  Hello

  my network is 10.21.21.0/24 as well as a local pool for the VPN Clients 10.21.21.100 - 200. Crypto map ist so the External value. There is no split tunneling configured for them. How can I get NAT Inet access clients? With any ACL I create, he got forward with their private IP (10.21.21.100).

  Any ideas?

  Thank you

  MB

  This document describes how to configure a firewall PIX 7.0.1 and later to run IPsec on a stick. This configuration applies to a particular case where the PIX does not allow the split tunneling, and users connect directly to the PIX until they are allowed to go to the Internet.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080103ed0.shtml

• ASA Anyconnect

  I have everything works, except that I can't connect to internet when connected to the VPN. Any help would be appreciated.

  You have the split tunneling configured? or you want to route all your internet traffic connected via AnyConnect through your ASA?

• AnyConnect to ASA 5505 ver 8.4 unable to ping/access within the network

  My AnyConnect VPN to connect to the ASA, but I can not access my home network hosts (tried Split Tunnel and it didn't work either). I intend to use a Split Tunnel configuration, but I thought I would get this job until I've set up this configuration. My inside hosts are on a 10.0.1.0/24 network and networks 10.1.0.0/16. My AnyConnect hosts use 192.168.60.0/24 addresses.

  I saw the messages of others who seem similar, but none of these solutions have worked for me.  I also tried several configurations NAT and ACLs to allow my internal network to the ANYConnect hosts and return traffic shaping, but apparently I did it incorrectly.  I undestand what this worm 8.4 is supposed to be easier to achieve, NAT and others, but I now have in the IOS router it is much simpler.

  My setup is included below.

  Thanks in advance for your help.

  Jerry

  *************************************************************

  ASA Version 8.4 (4)

  !

  hostname mxfw

  domain moxiefl.com

  activate the (deleted) password

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  Shutdown

  !

  interface Ethernet0/4

  Shutdown

  !

  interface Ethernet0/5

  switchport trunk allowed vlan 20.22

  switchport mode trunk

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.0.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  interface Vlan20

  nameif dmz

  security-level 50

  IP 172.26.20.1 255.255.255.0

  !

  interface Vlan22

  nameif dmz2

  security-level 50

  IP 172.26.22.1 255.255.255.0

  !

  passive FTP mode

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  name-server 208.67.222.222

  Server name 208.67.220.220

  domain moxiefl.com

  permit same-security-traffic inter-interface

  network of the Generic_All_Network object

  subnet 0.0.0.0 0.0.0.0

  network of the INSIDE_Hosts object

  10.1.0.0 subnet 255.255.0.0

  network of the AnyConnect_Hosts object

  192.168.60.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.60.0_26 object

  255.255.255.192 subnet 192.168.60.0

  network of the DMZ_Network object

  172.26.20.0 subnet 255.255.255.0

  network of the DMZ2_Network object

  172.26.22.0 subnet 255.255.255.0

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 dmz

  dmz2 MTU 1500

  local pool VPN_POOL 192.168.60.20 - 192.168.60.40 255.255.255.0 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  NAT dynamic interface of Generic_All_Network source (indoor, outdoor)

  NAT (inside, outside) static source INSIDE_Hosts INSIDE_Hosts static destination AnyConnect_Hosts AnyConnect_Hosts-route search

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.60.0_26 NETWORK_OBJ_192.168.60.0_26 non-proxy-arp-search to itinerary

  NAT (dmz, outside) dynamic interface of Generic_All_Network source

  NAT (dmz2, outside) dynamic interface of Generic_All_Network source

  Route inside 10.1.0.0 255.255.0.0 10.0.1.2 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  AAA authentication http LOCAL console

  Enable http server

  http 10.0.0.0 255.0.0.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec ikev2 AES256 ipsec-proposal

  Protocol esp encryption aes-256

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES192

  Protocol esp encryption aes-192

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal AES

  Esp aes encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 proposal ipsec 3DES

  Esp 3des encryption protocol

  Esp integrity sha - 1, md5 Protocol

  Crypto ipsec ikev2 ipsec-proposal OF

  encryption protocol esp

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  registration auto

  domain name full anyconnect.moxiefl.com

  name of the object CN = AnyConnect.moxiefl.com

  Keypairs AnyConnect

  Proxy-loc-transmitter

  Configure CRL

  string encryption ca ASDM_TrustPoint0 certificates

  certificate 439 has 4452

  3082026c 308201d 5 a0030201 9a 445230 02020443 0d06092a 864886f7 0d 010105

  05003048 06035504 03131641 6e79436f 6e6e6563 742e6d6f 78696566 311f301d

  6c2e636f 312530 2306092a 864886f7 0d 010902 1616616e 79636f6e 6e656374 6 d

  2e6d6f78 6965666c 2e636f6d 31333039 32373037 32353331 5a170d32 301e170d

  33303932 35303732 3533315a 3048311f 301D 0603 55040313 16416e79 436f6e6e

  6563742e 6d6f7869 65666c2e 636f6d31 86f70d01 09021616 25302306 092a 8648

  616e7963 6f6e6e65 63742e6d 6f786965 666c2e63 6f6d3081 9f300d06 092 has 8648

  86f70d01 01010500 03818d 00 30818902 8181009a d9f320ff e93d4fdd cb707a4c

  b4664c47 6d2cc639 4dc45fed bfbc2150 7109fd81 5d6a5252 3d40dc43 696360d 5

  fbf92bcc 477d19b8 5301085c daf40de5 87d7e4aa f81b8d7f 8d364dfa 0a6f07d7

  6a7c3e9b 56e69152 aa5492d8 e35537bd 567ccf29 7afbeae8 13da9936 9f890d76

  1d56d11d da3d039a 0e714849 e6841ff2 a3633061 03010001 300f0603 b 5483, 102

  1301 01ff0405 30030101 ff300e06 03551d0f 0101ff04 86301f06 04030201 551d

  23 04183016 80142f27 7096c4c5 e396e691 e07ef737 af61b71f 64f1301d 03551d

  0603551d 0e041604 142f2770 96c4c5e3 96e691e0 7ef737af 61b71f64 f1300d06

  092a 8648 86f70d01 01050500 03818100 8f777196 bbe6a5e4 8af9eb9a 514a 8348

  5e62d6cd e430a758 47257243 2b 367543 065d4ceb 582bf666 08ff7be1 f89287a2

  ac527824 b11c2048 7fd2b50d 6aa00675 e4df7859 f3590596 b1d52426 ca 35, 3902

  226 dec 09 713f7ba9 80bdf7bb b52a7da2 4a68b91b 455cabba 4e77f4b0 1e97a52c

  0cc4c6f3 f244f7d9 0a6e32fb 31ce7e35

  quit smoking

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 10

  aes-192 encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 20

  aes encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 30

  3des encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  IKEv2 crypto policy 40

  the Encryption

  integrity sha

  Group 2 of 5

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Crypto ikev2 access remote trustpoint ASDM_TrustPoint0

  Telnet timeout 5

  SSH 10.0.0.0 255.0.0.0 inside

  SSH timeout 5

  SSH group dh-Group1-sha1 key exchange

  Console timeout 0

  dhcpd dns 208.67.222.222 208.67.220.220

  dhcpd outside auto_config

  !

  dhcpd addresses 10.0.1.20 - 10.0.1.40 inside

  dhcpd dns 208.67.222.222 208.67.220.220 interface inside

  dhcpd allow inside

  !

  dhcpd address dmz 172.26.20.21 - 172.26.20.60

  dhcpd dns 208.67.222.222 208.67.220.220 dmz interface

  dhcpd enable dmz

  !

  dhcpd address 172.26.22.21 - dmz2 172.26.22.200

  dhcpd dns 208.67.222.222 208.67.220.220 dmz2 interface

  dmz2 enable dhcpd

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL-trust outside ASDM_TrustPoint0 point

  WebVPN

  allow outside

  AnyConnect essentials

  AnyConnect image disk0:/anyconnect-win-3.0.2052-k9.pkg 1

  AnyConnect profiles AnyConnect_client_profile disk0: / AnyConnect_client_profile.xml

  AnyConnect enable

  tunnel-group-list activate

  internal GroupPolicy_AnyConnect group strategy

  attributes of Group Policy GroupPolicy_AnyConnect

  WINS server no

  value of server DNS 208.67.222.222 208.67.220.220

  client ssl-VPN-tunnel-Protocol ikev2

  moxiefl.com value by default-field

  WebVPN

  AnyConnect value AnyConnect_client_profile type user profiles

  password username user1 $ $ encrypted privilege 15

  password username user2 $ $ encrypted privilege 15

  tunnel-group AnyConnect type remote access

  tunnel-group AnyConnect General attributes

  address VPN_POOL pool

  Group Policy - by default-GroupPolicy_AnyConnect

  tunnel-group AnyConnect webvpn-attributes

  enable AnyConnect group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  Review the ip options

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:f2c7362097b71bcada023c6bbfc45121

  : end

  Hello

  You may have problems with the NAT configurations

  Look at these 2 high page configurations

  NAT dynamic interface of Generic_All_Network source (indoor, outdoor)

  NAT (inside, outside) static source INSIDE_Hosts INSIDE_Hosts static destination AnyConnect_Hosts AnyConnect_Hosts-route search

  The solution is either to reconfigure the dynamic PAT with the lowest priority (goes tearing down the current normal outbound connections) OR reposition the exempt NAT / configurations NAT0

  Dynamic change of PAT could be done with

  no nat dynamic interface of Generic_All_Network source (indoor, outdoor)

  NAT automatic interface after (indoor, outdoor) dynamic source Generic_All_Network

  NAT0 configuration change could be done with

  no nat source (indoor, outdoor) public static INSIDE_Hosts static destination INSIDE_Hosts AnyConnect_Hosts AnyConnect_Hosts-route search

  NAT (inside, outside) 1 static source INSIDE_Hosts INSIDE_Hosts static destination AnyConnect_Hosts AnyConnect_Hosts-route search

  Changing the order of the NAT0 configurations as described above is probably the simplest solution and does not cause a teardown of connections for users. Of course change the dynamic configuration PAT would avoid future problems if it can generate. For example, it could overide static PAT (Port Forward) configured with Auto NAT configurations.

  Try option suites you best and let know us if it solved the problem

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary

  -Jouni