Spooler subsystem application order

My printers do not work I get the message that the Spooler Subsystem App stopped working and was closed. He repeated to me that I need to reinstall the drivers.

See if the FixIt can work his magic: http://support.microsoft.com/mats/printing_problems/en-us

Tags: Windows

Similar Questions

Spooler subsystem application does not

Title: spooler subsystem acpplication

I keep getting an error message indicating "Spooler Subsystem app works not. I'm unable to locate information on how to solve this problem. Please provide assistance.

Hello

-What is the operating system installed on your computer?

-When exactly you receive this error message?

-You are aware of any changes made on the computer before this problem?

If the question is everything when trying to print, I suggest you to follow the methods mentioned below and check if that helps.

Method 1: Run the FIXIT from Microsoft from the link below and check if the problem persists.

Diagnose and automatically fix problems printing and printer

http://support.Microsoft.com/mats/printing_problems/

Method 2: I also suggest you to see the link below and check if that helps.

Printer in Windows problems

http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

Response with more information to help you further.

Hope this information helps.

Had a blue screen and "Spooler SubSystem App stopped working.

"Spooler SubSystem App stopped working and was closed" appears whenever I turned on my laptop for a week. Also, a message appeared twice telling me: blue screen problem event name. I don't know what it means all the

Hello

1. have you done any change in software on the computer lately?

Please check if you face the same problem when recording in safe mode. It is a possibility that one of the non-Microsoft application or driver is causing this issue. Start in safe mode and make sure that us. If you are able to start properly in safe mode, we can perform a clean boot in order to find the root cause.

Step A.
a. restart your computer.
b. when the computer starts, you will see your computer hardware are listed. When you see this information tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows 7 Advanced Startup Options.
c. using the arrow keys, select the desired option of Mode without failure.
d. press the Enter key on your keyboard to start in safe mode of Windows 7 with networking.
e. when Windows starts, you will be at a typical logon screen. Connect to your computer and Windows 7 goes into safe mode.
f. do whatever tasks you need and when you are done, reboot to return to normal mode.

Step B.
If it works fine in safe mode try performing a clean boot in order to find the cause root.
See the article below for instructions on how to start your computer in a clean boot state.
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135
Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

I hope this helps.

Spooler Subsystem App stopped working:

Original title: Spooler Subsystem

Spooler Subsystem App stopped working:
Signature of the problem:
Problem event name: APPCRASH
Application name: spoolsv.exe
Application version: 6.0.6000.16386
Application timestamp: 4549b 734
Fault Module name: localspl.dll
Fault Module Version: 6.0.6000.16850
Timestamp of Module error: 49f06576
Exception code: c0000005
Exception offset: 0001317e
OS version: 6.0.6000.2.0.0.256.1
Locale ID: 1033
Additional information 1: 8 d 13
More information 2: cdca9b1d21d12b77d84f02df48e34311
Additional information 3: 8 d 13
Additional information 4: cdca9b1d21d12b77d84f02df48e34311

for some reason, I had this same problem a few days later but has a job waiting inside as well. In the end, I did a system restore to a previous point that seems not to give the same problem since

Vista SP2 after installing Spooler SubSystem App stopped working and was closed

After installing Vista SP 1 and 2 my printers no longer work. the message that I get when the computer is

"Spooler SubSystem App stopped working and was closed. A problem with the application to stop functioning properly. Windows will notify you if a solution is available.

When I try to print it says I have to install a printer but then says turn the spooler.
After turning on the spooler spooler turns his back on the coast.
I tried to uninstall and reinstall printers, but it won't let me install printers.
If I restore to previous date before installing SP1 and 2 printers work.

Online, I see that many people have the same problem.
I tried to contact Microsft but they tell me to contact HP
and when I contact HP they tell me to contact Microsoft, as it was their problem
I'm agree that Microsoft SP1 and 2 caused this problem.

Hello Lonny Jones,

Let's start by downloading the latest drivers and software from HP and see if that helps.

When you install the drivers, it is important to perform the following actions:

1. remove the printer from the PC.

2 uninstall the printer from the PC driver.

3 reinstall the printer driver.

4 reinstall the printer.

Several references to printer:

Open the printer Troubleshooter

http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

Why can I not print?

http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

Find and install printer drivers

http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

Spooler subsystem app has to stop

I've used two different 'fix it' programs on the application subsystem spooler who said he fixed it, but it will maybe print once and then comes back to the same problem. Help!

Hello

Check chan seen message here - one of the highest.

fixed spooler subsystem app stopped working
http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e

===================================

If the above didn't help:

Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
the latest driver).

Check Mr. Fixits here and if you use the other methods go back and try again later.

Problems of print and error - a Mr Fixit of printing
http://support.Microsoft.com/GP/printing_problems

Solve printer problems - a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx

------------------------------------------------------
Logon as administrator

Start - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN

You can copy and paste each line except those brackets and press ENTER after each.

net stop Spooler

(echo suppression of all print jobs)<-- you="" should="" see="" this="">

ping localhost n 4 > zero

del/q %SystemRoot%\system32\spool\printers\*.*

net start Spooler

(sound Done!)<-- you="" should="" see="" this="">

ping localhost n 4 > zero

Another way
http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/

Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspx

If you use Control Panel - Classic - printers

Try after unplugging your printer if necessary.
-------------------------------------------------------------

Also check the spooler print and its dependencies and addictions Service.

Print Spooler service
http://www.blackviper.com/WinVista/services/Print_Spooler.htm

How difficulty Windows Vista print spooler starts do not
http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html

------------------------------------------------------------

Check this thread if necessary - to stop and erase the spooler

http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a15779d6-ac0d-42FD-9Ac2-a1da241ea19f/

and here
http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/58b54fa9-cf6f-40F7-90b2-8093c6777493

------------------------------------------------------
Clean the General corruption and repair or replace the damaged/missing files.

Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

Enter this at the command prompt - sfc/scannow

How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228

CheckDisk (chkdsk) runs at startup.

How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

Spooler subsystem app stopped working, was closed due to the DEP. How can I restart it.

How can I restart Spooler subsystem. Remember - this is a public forum so never post private information such as numbers of mail or telephone!

Ideas:
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
If you mean the Spooler Service, go to start / Control Panel / Administrative Tools / Services and scroll to spooler and make sure that it is set to automatic (put it in auto mode if it is not) and make sure that it is started. If it is running, stop it and then restart it again. If it is stopped, start it just.

If you speak another application, to be more specific and provide the name and version of the application as well as the EXACT text message you received (including all codes). Here is an article on how to enable or disable DEP using programs that can help: http://www.vistax64.com/tutorials/65790-dep-turn-off-programs.html.

I hope this helps.

Good luck!

Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

Photosmart C4485 Spooler subsystem app

I have a fairly new C4485, only bought last month. So far, I have had no problems at all with it.

But now when I log in there is an error message saying that the Spooler Subsystem App stopped working as was closed. The printer also is no longer recognized as connected.

However, I can still send print jobs, but it will print only a very small amount before stopping.

I went and downloaded the drivers and patches on the site of hp (However, I knew that the pilot was already up to date). But I can not install them in any case, as it says it cannot find the printer and the installation stops.

I use Windows Vista Business 32-bit.

Can someone advise me on how to solve this problem, thank you.

Message edited by David_David on 03/07/2009 02:03

OK, now press Windows + R key to bring up the run window and type 'cmd', make sure that the "run this program as an administrator" is checked and click OK. Now, type the 3 commands below in order.
```
net stop spooler
sc config spooler depend= RPCSS
net start spooler
```
Note the space between "=" and "RPCSS". This space is IMPORTANT. Once this is done, close the command prompt window and try printing.

I get a Spooler Subsystem app error. I have XP SP3. I tried several fixes no work no matter who else getting this error?

I have a Canon MG5220 printer. I can print from my wireless on my laptop that runs windows 7.

Hello
1. What is the full error message?
2. All changes made to the computer before the show?
Check out the link and follow the steps.
You cannot print and you receive the error message "Spooler subsystem app has encountered a problem and needs to close."
http://support.Microsoft.com/kb/810894

Important registry This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

Spooler SubSystem App has encountered a problem and needs to close. We are sorry for the inconvenience.

Spooler SubSystem App has encountered a problem and needs to close. We are sorry for the inconvenience.

Hello

1. When you get this error message?

2. that you get this error message when printing?

3. What is the brand and model of the printer?

4. don't you make changes to the computer before the show?

Please provide us with more information on this issue to help you best.

If you get this error when printing, follow the steps from the link below.

Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

http://support.Microsoft.com/kb/322756

How to back up and restore the registry in Windows

http://support.Microsoft.com/kb/810894

' error spooler subsystem app

How to fix Spooler subsystem errors

How to fix Spooler subsystem errors

Start off by explaining at least the following:
- The full error messages you get, without paraphrasing
- What version of Windows you have, including the service pack
- The circumstances in which you get these errors (i.e., what you try to do)
- What happens when you restart the computer after receiving such an error
- The brand and model of your printer
For most print spooler crashes (which may or may not apply to you):

Clean potentially corrupt print jobs:

Open a command prompt window (start > run > cmd > OK) and type the following commands pressing enter in the black command prompt window, after each command

net stop spooler
del "% windir%\system32\spool\PRINTERS\*.*" [press y when you are prompted.
net start spooler
output

Clean and reinstall your printer driver by using the instructions here . If you have or have had a Lexmark printer, use the directions here instead.

Spooler subsystem app has encountered a problem.

HP Laserjet 1020 printer does not work. Have used this printer for years. Last print job has stopped the printing process and give the spooler subsystem app has encountered a problem error message.

Used Mr. Fixit. Have the print spooler service manually restarted and the RPC service. When I try to print, Spooler Subsystem App Error message appears and printer spooler stops,

OS is XP Home Edition Service Pack 3.

Cannot remove hardware HP Laserjet 1020 and reload HP Laserjet 1020 download did not fix problem.
Often, but not always, the symptoms you describe are caused by a corrupt print job stuck in the queue or a damaged printer driver. However before you clean things up, on general principles, that you can download, install, update and run full scans with each of these two free programs:

AntiMailware MalwareBytes
SUPERAntiSpyware

Do not operate the two scans simultaneously. Each will take a long time, so start it and then go do something else for a while.

Cleaning of printers

NOTE: If after completing step has the print spooler is not always running after you launched the command "net start spooler", you will not be able to follow all the steps in "First Article". Use of the special procedure for printers Lexmark described below and follow in its first Article. If still no joy, use the alternative method that is linked below.

A. Clean on print jobs pending
- Open a command prompt window (start > run > cmd > OK)
- Type the following in the black command prompt window, and then press ENTER after each line
net stop spooler
del/q '% windir%\system32\spool\PRINTERS\*.* '.
net start spooler
output

B. clean the old printer drivers and install the latest drivers by using the directions in One Article.

A special procedure for computers that have or had a Lexmark or Dell-badged Lexmark printer.

Open a command prompt window (start > run > cmd > OK)

Type the following in the black command prompt window and press enter

dependent on the spooler of sc config = RPCSS
output

Note that there is no space before the =

If you want to use a Lexmark or Dell-badged Lexmark printer after having done the above, you will need to reinstall it.

Alternative to the method of his first Article: http://members.shaw.ca/bsanders/CleanPrinterDrivers.htm
Use of SuperAntiSpyWare found two serious problems. Could cross printer of pending work. Printer works fine. Thanks for your reply and advice.

Best regards

Spooler Subsystem App has encountered a problem and needs to close

We cannot print anything on my computer. the message is that the Print Spooler Subsystem App has encountered a problem and needs to close. How to get the print spooler to run and work my printer start?

Hi Saeed,

1. were you able to use the printer before without any problem?

2. did you of recent changes on the system?

3. What is the brand and model of the printer?

Method 1:

You can try to start the Fixit from the following link and check if it helps.

Problems printing and printing errors

Method 2:

You can also read the following article and check if it helps.

You cannot print and you receive the error message "Spooler subsystem app has encountered a problem and needs to close."

Spooler SubSystem App error in windows xp

I am running windows xp and have had a HP photosmart printer installed for over a year. From now on I get the error: Spooler SubSystem App has encountered an error. I can print the screen and print from IE8, but whenever I try to print from Adobe Pagemaker I get this error.

Adobe has a forum for all their products, including PageMaker:

http://forums.Adobe.com/community/pagemaker_general

I've never seen your problem, but if you search the forum Adobe PageMaker for:

Spooler Subsystem App

You will see that you are not alone and find some discussions that involve more than one printer HP and PageMaker and maybe some of these ideas will be a source of inspiration or help.

If you find nothing inspiring, I post there and see what they have to say.

Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

Error message Spooler SubSystem App

Hi - my computer has received an automatic update from Microsoft some time this morning and now I get the following message appears and cannot print: "Spooler SubSystem App has encountered a problem and needs to close. We are sorry for the inconvenience. "I'm lost as how to solve this problem. Can you help me?

See how it works:

We are going to stop the Print Spooler Service and delete any backup up/stuck/in waiting it for print jobs and restart the Print Spooler Service.

To clear the print queue, stop the print spooler service and delete all the pending print files.

You cannot delete all print jobs in the queue so that the Print Spooler Service is running.

To stop the Print Spooler Service, click Start, run and enter in the box:

services.msc

Click OK to open the Services Applet.

Locate the Print Spooler Service, right click and choose 'Properties' and then click on the "Stop" button to stop the Print Spooler Service is running.

The option "Startup Type" of Service properties print spooler is usually set to "Automatic" (which is now a good time to check it out).

If the "Startup type" is not set to "Automatic", set the "Startup type" to "Automatic" If that is your desire (which now is the time to check it out).

Do not try to start or restart the Print Spooler Service again...

Then, delete all updates pending upward and forward to printing from XP. If they do not print before, you will need to send the to the printer again.

Using Windows Explorer, navigate to the following folder (assuming that Windows is installed on your C drive):

C:\WINDOWS\system32\spool\PRINTERS

Delete all the print jobs in queue (select and delete all the files) in the folder if the folder is without waiting for print jobs. The folder must be empty when you are finished.

Reboot your system and check the Print Spooler Service again to make sure the Print Spooler Service restarts automatically restart (given that the startup type is set to automatic).

After the reboot, check again the spooler service for printing and the 'Status' column for the print spooler must be read "started."

Submit new failure of print jobs.

Spooler subsystem application order

Similar Questions

Maybe you are looking for