spots on the sides of the paper LaserJet Pro 400

Similar Questions

• LaserJet Pro 400 M451dn: Problems copying documents from the printer scanner

  I use a Mark II of Canon Canoscan 9000F scanner to scan documents and copy them into the HP LaserJet Pro 400 451dn color laser printer.  I use the 'Copy' button on the front of the scanner function.  When a color or photo document is scanned this way the red and blue colors are reversed when it comes to the printer off.

  Both the scanner and the printer work perfectly in all other situations.

  Somehow the red and blue colors are to be swapped when a document goes to the scanner to the printer.

  I called the Support Canon technique and they told me that they have never heard of this problem and have never had it reported before.  When you use the "Copy" button function there is no setting that can be done. The scanner copy what he sees.

  So why the red and blue are exchanged on the printer?

  Teknishun

  What happens if you scan the document itself to the computer and then print the scanned copy? If it is ok, then the question must be the scanner software which sends the document to the printer and has nothing to do with the printer. Sorry, but it's a hot issue.

• LaserJet Pro 400 M401n: How to set the margins for binding up and left for LaserJet Pro 400 M401n

  I am connected to ePremis (medical site) that allows me to print the selected medical forms. ePremis uses the default printer to print the selected form.  The selected form should be printed on a preprinted form that I load into the tray of the printer.

  The problem is that ePremis does not provide an option to set gutter margins and print aligns correctly with my pre-printed form. The print position is a little weak and must also be shifted a little to the left. I need to reduce the high binding margin to move the position of superior print on the page and the left binding margin must also be reduced to move the print a little position to the left so that the printed data will properly align with my pre-printed form.

  Since ePremis does not offer an option to set the margins of the gutter, I need to be able to set the margins of the gutter through the printer driver, but there is also no option provided by the printer driver dialog box to set the margins of the gutter.  :-(

  Is it possible to set the printer LaserJet Pro 400 gutter margins?  I see the margins left and right options in the driver dialog box printer, but they are grayed out and cannot be changed.

  I have another printer, Kyocera laser printer, and I don't have this problem with the Kyocera because it offers the possibility to set gutter margins in the printer driver dialog.  I wonder why the LaserJet Pro 400 does not provide this option?

  I perhaps could solve this problem by sending PCL6 commands to the printer before printing?  I'm a programmer and am open to this option if it would work.

  Your help would be much appreciated.  Thanks in advance!

  Setting margins generally depends on demand - but (you say) that your application does not allow this.

  Some printers provide functionality of saving images , whereby the position of the image of the page onto a physical sheet can be adjusted to the printer, usually on a basis of by-tray.

  For example, with my Laserjet Pro MFP color 400 M475dn, the appropriate menu/menu item is described as follows:

  

  Note:

  • This setting applies to the bar up this that changed, so will have an impact on all the tasks using the specified status bar.
  • Not all printers support these features - I have no idea if your LaserJet M401 exercises or not.

  With regard to the '... sending the commands to the printer before printing... PCL6«» :

  • PCL6 (PCL XL) rather more autonomous than PCL5is, so I'm pretty sure that nothing you can "send" to the device to influence the outcome of the following printing.
  • Even with PCL5 print jobs, standard printer drivers are "overcome and-tail' with universal output language (UEL) escape sequences (which reset the device to the market environment (user - default)), which would be too mount sequences exhaust specific PCL5 previously sent to the device.

• Windows RT and HP LaserJet Pro 400 M401w

  I'm trying to connect the HP LaserJet Pro 400 M401w to my Surface tablet running Windows RT.

  I tried to put in the IP, wireless sensor and using the USB cable.

  He is not with the IP or wireless detection.

  With the help of the key USB Cable it things is a CD Rom   If I add a printer and trying to choose manually the printer isn't on the list.  Any help would be appreciated.

  Hi SydsMom, welcome to the Forums of HP. If a product contains the necessary built in the RT drivers, he just needs to be plugged and RT Windows should recognize and install it.
  
  I did a search for "HP LaserJet Pro 400 M401dw Laser printer" with the: Windows Compatibility Centerand it's Windows RT 8.1 compatible.
  
  Microsoft provides these simple instructions: install a printer in Windows 8.1, Windows RT 8.1
  
  In addition, I'm not familiar with that printer, as it is a business model supported. I suggest posting in the trade forums, to get more input. You can do this HERE.
  
  Series HP LaserJet Pro 400 printer M401 Support

• Reference Dell D10S: Software 451dn Laserjet Pro 400 has error during installation.

  LaserJet works fine when plugged in to USB, but now moved to a place wireless. The software will not work.

  I tried install printer Win 10: "the pilot is not available.
  Tried to uninstall the universal printer driver, restart, reinstall the HP driver, error (without code).

  HP Print doctor can find the device downloads the latest version, but it crashes every time (error, no codes).

  Win 10 can see the printer... it is therefore in the range wireless.

  I tried all the software different packaging to win 10 on HP site... all get an error during installation.

  Here's what worked.  I downloaded the universal print driver from HP.  These installed to their default location.  Taking note of where they have installed.

  Then, 10 Windows, try installing the printer laserjet Pro 400.  "Missing drivers".<- this="" is="" an="" important="" step.=""  leave="" the="" printer="" icon="">

  Then go to control panel, small icons.  Device Manager.  Search for printers, find the Laserjet printers.
  Right-click and choose update drivers.  Do not update automatically.  Choose the manual option.

  Look for the universal printer driver.  Wait a minute... BOOM.  All right.  Printing of all wireless PC and laptop.

• Where is the location of the fonts on LaserJet Pro 400 MFP M425dn dimm?

  I recently bought a LaserJet Pro 400 MFP M425dn and to install a strip of memory custom font I bought for another printer that accepts fonts DIMM.

  The problem is that I can't find the font dimm location, even if the configuration of the printer said very clearly that there is a 'Slot DIMM 1. Said user's Guide: 'this product includes a panel of memory which will accept the following third party font and barcode... '. "- but it does not say where is this"sign of memory. "

  There is a door on the left side of the printer, but it has only a rectangular socket, not a DIMM slot.

  Can anyone solve this mystery? Thanks much for any help.

  Thanks - but it was not the question. I'm not trying to add memory to the printer, but instead to add a MEMORY programmed bar that includes additional fonts.

  For the love of someone else who may be interested, I finally found the answer to my own question on TypeHaus website:

  This side door on the left (in fact) the door to the DIMM of fonts. I didn't recognize it as a door of police-dimm because the last style font dimm HP uses different hardware than what they used in the past. The new design doesn't have the pins on one edge of the DIMMs, as do the older styles, but instead uses a rectangular connector on the underside.

  You can see the answer here:

  http://typehaus.com/pubs/custom/Fcd1/insg/Custom_Fcd1InsgHpxx120611AS.PDF

  The illustration is specifically a D401, but the design of the door and socket are identical to the design door and taken on the M425dn.

  I hope this can help someone else who may be as puzzled as I was!

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

• MFP HP LaserJet Pro 400 M425dn will not print the text to format 72 points or more

  My workplace has recently bought a M425dn of MFP HP LaserJet Pro 400 all-in-one printer. It works perfectly except for the fact that it will not print text that is 72 points or larger in size. I tried many fonts that are installed with Windows, and all them print correctly to the point size 71.5 or smaller; Another thing simply does not appear in prints. Content which is of size to 72 points or more * fact * affect the flow of the content printed on the page, however. It's like the 72 points or larger text takes up space, but it is completely invisible on the printed page.

  I tested using Microsoft Word 2002 on three separate computers, of which two have installed Windows 7 and Windows Vista installed. The problem is the same on all three computers. The printer is connected via an ethernet cable to our wired network. I have installed the printer software included, and I don't think that there are updates for it that have not been installed up to this point.

  Any thoughts on how to solve this problem?

  Hello, I just made an account to solve this problem for you guys because it has been a puzzle to me also...

  I apologize before the huge hand for the terrible grammar and punctuation that I'm in a hurry

  Now it does not work for everyone but I fixed it on my machine with the following

  now before you print it... .use (ctrl + p) in your text editor to open the print window, click (properties), and then navigate to the tab (Advanced) now, I have a section called the characteristics of the printer in this category there is an option to 'send truetype as bitmap' activate this and see if it can help someone of you, for me, with this PERMIT I can print any font size my processor will allow me to type

  in my machine's plug

  Reference Dell d6420

  Win7

  Msoft word 2007

  printer itself is

  HP laserjet 200 color m276

  printer driver is

  HP LaserJet 200 color MFP M276 PCL 6

  I understand that this printer and driver is not identical to yours in itself, but the nature of these drivers makes it highly likely that this solution works for most of you

  If this can help, someone else did post more because I'll probly do not sign in to this site I created this account just for this post and I hope to solve this annoying problem issue for many of you... .no necessary congratulations

• turn off the broadcast without wire - HP laserjet pro 400 color mfp m475dw

  How do I disable broadcasting SSID for HP laserjet pro 400 color mfp m475dw.  I disabled the configuration via the web console wireless printer, but it is still broadcasting.  I also updated the firmware to 20131028 last available.

  Since it is wiered one of the scenario, I could solve this with the help of the HP Support is by doing factory reset/NVRAM reset the unit by turning the printer and holding right arrow and cancel on the touch screen of the device (cancel is on the lower right of the touch screen on the black area and right arrow is just above him (one in the middle of the Panel) in the same black box) and the device of turning on until the message something like storage reset... is displayed and can release the two buttons/zone button.

• LaserJet pro 400 m425dn mfp: mfp laserjet pro 400 m425dn will not connect to the network

  I just bought a mfp laserjet pro 400 m425dn printer/phtocopier and I can't seem to connect to our network.  I have it plugged into the router and it says "cable disconnected" without an IP address.  I don't have the USB cable to configure the machine and I was hoping to do it via the network (which tells me is an option).  I don't know if that has something to do with it.

  Any help would be greatly appreciated.

  The printer should be released the box set up using DHCP for addressing.

  When plug you it into the router it should pull an IP address, if it is its cable disconnected then you might have a bad port on the router, a bad cable or a bad printer.

  Plug something else into the same port with the same cable and see if it works, if you have a defective printer and need to return it and get a replacement.

  You may also be able to find someone to replace the trainer who has the network port to it.

  If my post is solved your problem and click the accepted as button solution under him.

  In order to thank a Tech for a post click the thumbs up button under the post.

  You can even click on the two keys...

• Help! Accidentally updated the firmware of the Laserjet pro 400 with firmware Laserjet CP4525

  Help!  Accidentally updated the firmware of the Laserjet pro 400 with Laserjet CP4525 firmware.  The printer is now just spit out pages and never reaches a State ready for the correct firmware.  I really hope that I don't have it bricked just with a click of silly.

  Can someone help or suggest a way to put the appropriate firmware?

  See you soon

  Glyn

  I got it due sort connect the laptop via USB drivers install and then deploy the firmware.

  I then had to delete and add the printer on our print server.

  See you soon

• Unboxing and configure the HP LaserJet Pro P1102W printer

  Learn how to perform a unboxing conversion and configure the HP LaserJet Pro P1102W printer.

  For other helpful videos, go to hp.com/supportvideos or youtube.com/hpsupport. Several support options for your printer are available at hp.com support.

  This video was produced by HP.

  I hope you find this useful and informative video.

• When you try to use the texture of the paper adobe pro, I get: error a reference to a file / folder: 104

  When you try to use the texture of the paper adobe pro with CC2015, I get: error a reference to a file / folder: 104

  left Adobe Creative Cloud for General Photoshop Discussion

• LaserJet pro 400 m401 will not pick up paper

  My laserjet pro 400 m401 will pick up paper from the tray. I have not changed the paper I use. It's # 20 at Georgia-Pacific paper. The printer has not been dropped or abused. If anything, we have treated the printer very carefully and gently. Therefore, I suspect any damage physical/mechanical/electronic. The feed roller makes a squeaking/squealing noise when it runs. The printer then times out and the screen displays the message "no paper pickup. All stop there.

  I fixed it myself! One of the springs two compression at the end of the paper closest to the front of the printer tray became weaker. I've removed, carefully strained it and reinstalled it, and it works as good as new.

• HP LaserJet Pro 400 MFP M425 - paper supply is still legal

  HP LaserJet Pro 400 MFP M425

  IM unable to have paper paper feed use.

  I can scan with the scanner bed and there select the paper letter correctly, but when I try to use the paper feed its still legal size

  Ive has restored to the default factory settings, but still the problem persists.

  How can I make the change to have select letter size.

  Thank you

  Hi @biggddc and welcome to the Forums of HP.

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do to Commercial Forums of LaserJet HP.

  I hope this helps!