Reference Dell D10S: Software 451dn Laserjet Pro 400 has error during installation.

Similar Questions

• Color HP LaserJet Pro 400 M451dw - error # 49

  We have the above printer. It has been working well for a long time now. It is configured with the ethernet cable.

  At this time, however, when the main user of the printer turns to for use, he first gets up says 'Ready', opens with the IP address then displays "error 49" "turn." This does not seem to do anything.

  I found a post that suggested by ensuring that the printer was not showing in the DHCP, and I do not see here.

  If anyone has any suggestions, please let me know. This is a printer that is much used by the primary user.

  Thank you.

  49 error usually means a firmware error (which could be due to a problem of trainer), but in some cases, it may be invoked by a sending system a use of "punk" (not necessarily a conventional print job) to the device.

  See thread http://h30499.www3.hp.com/t5/Multifunction-and-All-in-One/LJ-Pro300-color-MFP-M375nw-Power-cycling-displays-quot-49/m-p/6348735

• MFP HP LaserJet Pro 400 M425dn will not print the text to format 72 points or more

  My workplace has recently bought a M425dn of MFP HP LaserJet Pro 400 all-in-one printer. It works perfectly except for the fact that it will not print text that is 72 points or larger in size. I tried many fonts that are installed with Windows, and all them print correctly to the point size 71.5 or smaller; Another thing simply does not appear in prints. Content which is of size to 72 points or more * fact * affect the flow of the content printed on the page, however. It's like the 72 points or larger text takes up space, but it is completely invisible on the printed page.

  I tested using Microsoft Word 2002 on three separate computers, of which two have installed Windows 7 and Windows Vista installed. The problem is the same on all three computers. The printer is connected via an ethernet cable to our wired network. I have installed the printer software included, and I don't think that there are updates for it that have not been installed up to this point.

  Any thoughts on how to solve this problem?

  Hello, I just made an account to solve this problem for you guys because it has been a puzzle to me also...

  I apologize before the huge hand for the terrible grammar and punctuation that I'm in a hurry

  Now it does not work for everyone but I fixed it on my machine with the following

  now before you print it... .use (ctrl + p) in your text editor to open the print window, click (properties), and then navigate to the tab (Advanced) now, I have a section called the characteristics of the printer in this category there is an option to 'send truetype as bitmap' activate this and see if it can help someone of you, for me, with this PERMIT I can print any font size my processor will allow me to type

  in my machine's plug

  Reference Dell d6420

  Win7

  Msoft word 2007

  printer itself is

  HP laserjet 200 color m276

  printer driver is

  HP LaserJet 200 color MFP M276 PCL 6

  I understand that this printer and driver is not identical to yours in itself, but the nature of these drivers makes it highly likely that this solution works for most of you

  If this can help, someone else did post more because I'll probly do not sign in to this site I created this account just for this post and I hope to solve this annoying problem issue for many of you... .no necessary congratulations

• LaserJet Pro 400 M451dn: Problems copying documents from the printer scanner

  I use a Mark II of Canon Canoscan 9000F scanner to scan documents and copy them into the HP LaserJet Pro 400 451dn color laser printer.  I use the 'Copy' button on the front of the scanner function.  When a color or photo document is scanned this way the red and blue colors are reversed when it comes to the printer off.

  Both the scanner and the printer work perfectly in all other situations.

  Somehow the red and blue colors are to be swapped when a document goes to the scanner to the printer.

  I called the Support Canon technique and they told me that they have never heard of this problem and have never had it reported before.  When you use the "Copy" button function there is no setting that can be done. The scanner copy what he sees.

  So why the red and blue are exchanged on the printer?

  Teknishun

  What happens if you scan the document itself to the computer and then print the scanned copy? If it is ok, then the question must be the scanner software which sends the document to the printer and has nothing to do with the printer. Sorry, but it's a hot issue.

• Help! My M475dn MFP HP LaserJet Pro 400 color printer will NOT print!

  HP LaserJet Pro 400 color MFP-M475dn-CE863A

  Printer on a network and can connect to multiple computers that include: Mac OS X, Windows 7 and Windows XP.

  When I try to print from my iMac, the print queue of the printer says "the printer is not connected.  When we try to print from Windows computers, it is in the right queue and does not print.  When I go the printer itself and try to print a page of demonstration or page supplies directly to him, it says on the screen which is printed, but nothing happens.  This is not hum or anything!  The port where the network cable is connected is switched on green that says HP which means that the network cable is connected.  We've had this printer for a year now, and something like that never happened.

  I did not have any software or anything like that until this happened.  It was working fine on Saturday when we used it, but when we arrived at work today, he just decided that it would interrupt printing!

  I'm puzzled!  I tried 'ping' IP address of the printer from my iMac and it pings fine.  Does anyone have advice?

  (I tried to make of the obvious like too switch the printer on and off and shutting the computer down and nothing!)

  Okay, so I feel a bit stupid right now.  I decided that I would be closed the printer for about an hour to see if it was there, and what you know-it has been!  I had to turn it off several times before but I guess it wasn't long enough.  What a pain!

  Thanks to everyone who took the time to read this!  Sorry to waste time everyone!

• LaserJet Pro 400 M451nw: Laserjet Pro 400 prints documents upside down

  My Laserjet Pro 400 prints documents upside down.  This only happens when you print in black and white, and from certain applications.  Files PDF and Word documents print very well, as plain txt files and files from my accounting software, but files CorelDraw and images in Photoshop CS5 reverse print.

  If I saved a CorelDraw file in PDF format, it will print correctly, but not the native file of COR.

  From Photoshop, it makes no difference what file format I print - jpeg, tif or even a file not saved - all printed reversed if I select black and white.

  Colour printing is fine for all applications.

  Like most of my needs to print b & w, I the printer defined as it as default and just change color when the need arises, but it means I lose lots of toner if I don't remember to print in color in CorelDraw or Photoshop.  Printing an image to grayscale in color also gives the evil eye.

  Any help appreciated.

  Hello

  Try to use a PCL5 driver, which is likely to solve such a.

  First, open the control panel > devices and printers, right click on the printer and select printer properties.

  Open the Ports tab, and take note of the path selected for the printer, and then close this dialog box.

  Download and install the driver HP UPD PCL5, follow the installation by selecting the traditional model.

  Follow the wizard of printwr indicated by selecting the same port as used by the original and complete its installation driver.

  The UPD driver can be downloaded from the following link:

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4157320&swItemId=ds_99378_6&swEnvOid=4158

  Once you have finished, try to print using the HP Universal printing PCL 5 driver and check for the difference.

  Please let me know if this can help,

  Shlomi

• LaserJet pro 400 mfp wil not install

  I tried setting my new laserjet pro 400 color mfp m475dn, two upward ways described in the installation guide; either via the automatic installation and CD rom. I followed the instructions exactly each 10 times I tried. I even downloaded the software again on the HP site and tried to install that. Each time the same result:

  "Install operation has been too long..." Fatal error etc."after he had reached and hung 99% installed.

  Any ideas guys?

  I am running Windows Vista Ultimate 64-bit.

  See you soon,.

  Neil.

  ndpadgett,

  You have two options:

  1. If you try to install this printer via a USB port, please do a network install and use the driver from hp.com.

  M475 solution print driver full

  2. If you unble to do a network installation, then please look to see if you have a universal print driver installed on your machine. If you do, then you must remove the UPD driver, re-boot and re - install the m475 SW.

• M475 MFP HP LaserJet Pro 400

  I just put a laptop for windows 7 64 bit. After you have installed the software package for a M475 MFP HP LaserJet Pro 400 via USB it analyzes not the sheet feeder. The scans are empty. Any ideas as to the cause.

  Lemmy25,

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a printer. You can do so at http://h30499.www3.hp.com/hpeb/ .

  I hope this helps.

• MFP HP LaserJet Pro 400 M425dn cold reset

  Hello!

  Help me! How can I make cold reset HP LaserJet Pro 400 MFP M425dn ?

  You can do 'factory reset' menu of the control panel; or permanent initialization of power first, holding and cover the corner area to the right / left of the control panel when you feed on... release your finger when you see «initialization permanent...» ». After you complete and return the loan, it indicates the reset is complete.

• LaserJet Pro 400 color m451dw: printer Laserjet Pro 400 color m451dw for window 10 drivers

  I can't find the drivers for a m451dw Color Laserjet Pro 400 running on Windows 10.  The only available operating systems are Mac.  Is there another place to look for drivers window other than the drivers regualer section 10?

  10 64-bit Windows

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5076462 & swLangOid = 8 & swEnvOid = 4192

  10 32-bit Windows

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5076462 & swLangOid = 8 & swEnvOid = 4191

  ------------------------------------------------------------------
  Say 'Thank you' by clicking the Bravo (Thumbs up) button in the post helped you.
  Please indicate the position that solved your problem as "acceptable Solution".

• laserJet Pro 400 color: printer

  Hello Mr President
  I want a help on your part I have a Color LaserJet Pro 400 m475dw MFP
  and when I turned it on. I show masseage like this {10.1002 electric memory error}
  How can I solve this problem, Mr President

  Hello Sir,

  The error that you expose is a problem with one of the toners.
  The magenta to be precise.
  
  In this case, the recommended action is to replace the magenta toner with an original RESUME.
  
  Kind regards

• Windows RT and HP LaserJet Pro 400 M401w

  I'm trying to connect the HP LaserJet Pro 400 M401w to my Surface tablet running Windows RT.

  I tried to put in the IP, wireless sensor and using the USB cable.

  He is not with the IP or wireless detection.

  With the help of the key USB Cable it things is a CD Rom   If I add a printer and trying to choose manually the printer isn't on the list.  Any help would be appreciated.

  Hi SydsMom, welcome to the Forums of HP. If a product contains the necessary built in the RT drivers, he just needs to be plugged and RT Windows should recognize and install it.
  
  I did a search for "HP LaserJet Pro 400 M401dw Laser printer" with the: Windows Compatibility Centerand it's Windows RT 8.1 compatible.
  
  Microsoft provides these simple instructions: install a printer in Windows 8.1, Windows RT 8.1
  
  In addition, I'm not familiar with that printer, as it is a business model supported. I suggest posting in the trade forums, to get more input. You can do this HERE.
  
  Series HP LaserJet Pro 400 printer M401 Support

• HP LaserJet Pro 400 m401dne: print from Notepad

  Hello! I have a new HP LaserJet Pro 400 m401dne. Everything works fine except when I try to print both sides of a Notepad document copies. As soon as I select the duplex option, the entire document disappears. We had an another HP LaserJet only printed on one side of the paper; who would have something to do with it? Still, I have this printer on the printer list but am selecting a new. I can print any other documents on 2 sides; just don't leave the notebook. Thanks for any help you can give me!

  Thank you, HP! The warranty issue has been resolved and so was the two-sided printing problem. The technician had to install Universal printing and now I can print copies front and back of notebook and everywhere else.  )

• HP LaserJet Pro 400 M401dw: HP ePrint App and Android 2.2

  Hello

  I hope that all is well.

  How can I find and install HP ePrint for Android 2.2? I just found this link https://play.google.com/store/apps/details?id=com.hp.android.print for Android 4.0 and more. For your information, my printer 'HP LaserJet Pro 400 M401 dw' and my smartphone ' HTC Desire, Android 2.2 ".»

  Thanks in advance for your help.

  We wish you the best.

  Mrwan

  Hello @Pooneh,

  Welcome to the Forums of HP's Support. I understand you are trying to install the HP ePrint app on Android 2.2 device. The ePrint application is only available for Android 4.0 versions and later versions. It is not supported for earlier versions of the Android operating system.

  Sorry if this isn't the answer or the solution you're looking for. If you have any other questions, feel free to ask.

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.