Spotting and slow system after a few clicks

Similar Questions

• The mouse hangs after a few clicks on Windows 7.

  Why my mouse freez after a few clicks?

  Original title: after a few clicks my mouse freezes for a few seconds... Why?

  Hi Pierre,.

  Thanks for posting your question in the Microsoft Community Forums.

  You have a problem with the gel on the computer mouse. It can be difficult when something that is important to you does not work as expected. It's pretty simple and we're here to help you solve the problem. We work as a team and get this sorted out.

  Please answer these questions-

  (1) is it a laptop or a desktop computer?

  (2) what is the brand and model of the computer?

  (3) that you get an error message or error code?

  (4) what is the version of Windows installed on the computer?

  (5) did you do changes on the computer before the show?

   

  I would like more information about the issue.

  Method 1-

  I wish that you are running the fixit as it automatically installs the updates required for the mouse-

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

   

  Method 2-

  Note: assuming that you are running Windows 7, I would have you consult the troubleshooting steps.

   

  Step 1-

  You should check if the problem persists in Mode without failure.

  Check out the link-

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

   

  Note: Make sure you connect in Normal Mode after all the troubleshooting steps.

   

  Proceed to step 2, if the problem does not occur in Mode without failure.

   

  Step 2-

   

   

  I recommend you to perform a clean boot.

  Placing the computer in a boot minimum state helps determine if third-party applications or startup items are causing the problem. You must perform the steps in the article-

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: You must follow the step 3 of the article to return the computer to a Normal startup after you perform all the troubleshooting steps.

   

   

  Method 3-

  I would have you look at the article-

  Mouse, touchpad and keyboard with Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/Mouse-touchpad-and-keyboard-problems-in-Windows

   

   

  We know if you need help. We will be happy to help you. We at Microsoft, strive for excellence and provide our customers with the best support.

  Thank you.

   

• Sound stops and slows down after the installation of Microsoft Vista SP2

  Its malfunction after installing Microsoft Visa SP2

  I have a HP laptop. downloaded Microsoft Vista SP! and SP2.  Since installing the sound stops and slows down and jump to the high state that Adobe Player slows down the computer.  I remember checking the updates in the control panel and Microsoft Vista SP1 and SP2 has been selected and windows poped place provided a specific that warning after installation of SP1 and SP2, respectively, the user can experience sound defects or.  This window also provided a specific procedure to correct the problem of noise; However, I have noticed no procedure to revisit this window.  Need help, thank you!

  I have a HP laptop. downloaded Microsoft Vista SP! and SP2.  Since installing the sound stops and slows down and jump to the high state that Adobe Player slows down the computer.  I remember checking the updates in the control panel and Microsoft Vista SP1 and SP2 has been selected and windows poped place provided a specific that warning after installation of SP1 and SP2, respectively, the user can experience sound defects or.  This window also provided a specific procedure to correct the problem of noise; However, I have noticed no procedure to revisit this window.  Need help, thank you!

  Here's a thread on these forums on how to fix this: http://social.answers.microsoft.com/Forums/en-US/vistamedia/thread/f16247af-313a-418d-915e-6403012c25eb

• Do not get the audit trail for oracle solaris running. It starts and then stops after a few seconds. How can I set up a secure target Oracle Solaris? cure

  I have installation BSM on my solaris 10 Server. I configured BSM to be sent to syslog. I registered my target secure on the server of the AV type Oracle Solaris. Add an audit trail of pointing to the syslog file. The Audit Trail starts and stops after a few seconds. the error I get from the agent log is

  [2014 11-25 T 11: 36:38.647 + 02:00] [collfwk] [ERROR] [] [] [tid: 10] [ecid: 192.169.1.50:11353:1416908198895:0, 0] FVO-8015: initialization of the instanceCollectionController AuditEventCollector error: run: process() Exception. [[

  Instance of Error initializing AuditEventCollector

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.initialize(CollectionController.java:322)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.process(CollectionController.java:402)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.run(CollectionController.java:350)

  at java.lang.Thread.run(Thread.java:662)

  Nested exception:

  java.lang.NumberFormatException: for input string: "invalid audit trail: / var/adm."

  at java.lang.NumberFormatException.forInputString(NumberFormatException.java:48)

  at java.lang.Integer.parseInt(Integer.java:449)

  in java.lang.Integer. < init > (Integer.java:660)

  to oracle.av.platform.common.exception.AuditException. < init > (AuditException.java:118)

  to oracle.av.platform.agent.collfwk.AuditEventCollectorException. < init > (AuditEventCollectorException.java:59)

  at com.oracle.solaris.SolarisCollector.initializeCollector(SolarisCollector.java:86)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.initialize(CollectionController.java:316)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.process(CollectionController.java:402)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.run(CollectionController.java:350)

  at java.lang.Thread.run(Thread.java:662)

  ]]

  [2014 11-25 T 11: 47:49.248 + 02:00] [collfwk] [ERROR] [] [] [tid: 11] [ecid: 192.169.1.50:11353:1416908869249:1, 0] FVO-8015: initialization of the instanceCollectionController AuditEventCollector error: run: process() Exception. [[

  Instance of Error initializing AuditEventCollector

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.initialize(CollectionController.java:322)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.process(CollectionController.java:402)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.run(CollectionController.java:350)

  at java.lang.Thread.run(Thread.java:662)

  Nested exception:

  java.lang.NumberFormatException: for input string: "invalid audit trail: / var/audit.

  at java.lang.NumberFormatException.forInputString(NumberFormatException.java:48)

  at java.lang.Integer.parseInt(Integer.java:449)

  in java.lang.Integer. < init > (Integer.java:660)

  to oracle.av.platform.common.exception.AuditException. < init > (AuditException.java:118)

  to oracle.av.platform.agent.collfwk.AuditEventCollectorException. < init > (AuditEventCollectorException.java:59)

  at com.oracle.solaris.SolarisCollector.initializeCollector(SolarisCollector.java:86)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.initialize(CollectionController.java:316)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.process(CollectionController.java:402)

  at oracle.av.platform.agent.collfwk.impl.controller.CollectionController.run(CollectionController.java:350)

  at java.lang.Thread.run(Thread.java:662)

  ]]

  Can you please help with instructions/solution implementation of Oracle Solaris secure target? A beginner in Audit Vault.

  I have the installation path for the database and which works very well

  concerning

  Thanks for the pointers. After you add hostname to the location of the trail, the audit trail is running

• Defective touchpad (Synaptics) and slow computer after extended use (memory leak)

  Two problems have been caused with my HP Split 2 x since I bought it 2 months ago:

  (1) the touchpad works sometimes for a few seconds, while the touchscreen still work OK.

  (2) the computer becomes slow after a while of use (which varies from a few minutes to a few hours usually). The Task Manager shows 98%-99% of memory, most of which use (3.6 GB / 4 GB) are not paged memory.

  I suspect the two issues are related to a faulty Synaptics driver, according to:

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/envy-X2-non-paged-pool-memory-l...

  and http://forum.notebookreview.com/razer/731374-memory-leak-synaptics-driver.html .

  I did the same test as the second link with the same result: Open "Task Manager" (Ctrl-Shift-Esc), on the 'Performance' tab, select 'memory '. Note the value for "Non paged memory. If I move the touchpad, it increases to about 1 MB every 5 seconds. If I stop moving, the value remains constant.

  I use the preinstalled Synaptics driver, version 17.0.10.9 (Sep 06, 2013) for 64-bit 8.1 window.

  Everyone has the same problem, or use it without these issues?

  I would like to know if a restoration system or factory reset may fix.

  FINALLY!

  Microsoft has just released an update for Synaptics Driver, not thanks to HP which has not found a way to provide the possible Synaptics driver as an OEM update.

  Update Windows Update to Sypatics HD TouchPad two days ago, but I would not be allowed to install as it kept then mainly in giving the 800F0100 error Code. After some research on the Internet I could find that an installation manual after the WU has downloaded the driver would be possible.

  So I went to the Device Manager > mice and other pointing devices > TouchPad Synaptics HID > properties > driver > Update Driver > Browse my computer for driver software and shown the finger/windows/C:\Windows\SoftwareDistribution/Download and everything worked like a charm = D

  I have no more memory leak and now after SEVEN MONTHS I finally can use gestures that it was supposed to.

  But I still annoyed gel problems which in my case is a dysfunction between the screen and the dock.

  Just that you wanted the guys at Microsoft to know is the solution, not the HP that would have had if they have signed and put the driver since November last at our disposal. Blame it on you, HP.

  Leo

• Fans of fast and slow mail after upgrade of Sierra

  So I too just upgraded to Sierra, and I have two problems.  The first I noticed almost immediately after a reboot is something is causing fans to run almost non-stop.  I looked at the level of the console and I see that several root applications use more than 100% of the time CPU.  What the hell is happening here?

  Second, Mail has now slowed down to the point that it is almost unusable.  I click on an email and it will literally be anywhere from 15 to 20 seconds for the mail to open.  Not a complex HTML with email of old thing plain video simple.  What the hell is happening here?  It's maddening.

  John W

  After installation of a new OS, there is a lot of cleaning up to do, just wait until she finishes

• Satellite P35-S605 slows down after a few minutes, then BSOD

  I am running Windows XP Pro and have contributed the most to the RAM on my P35.

  I had a local computer repair shop disassemble, clean all the dust and junk on, remove the processor and reinstall using thermal transfer compound. The computer has worked fine until I did this. When I came back and turned it on it started OK but started to slow down until the barley by working, and then I got the BSOD. After the memory dump, it restarted and repeat the process. After having tried several reboots, I finally gave up and called the computer repair shop I had used and returned to them. After a day, they said, it must be my drive hard because they replaced my hard drive with one of their and he ran all night with no problems. I had an old hard drive that I had removed from this machine, a few weeks before to move to a bigger so I put the old back road. The same problem remained. I again called the repair shop and told them what I had done, but they said they couldn't help me. I'm not recommedn this shop to anyone.

  I was myself so after that reading many articles on the Internet, I desided to try to fix it myself. I erased the hard disk using a set 0 wipe the program. I did a disk image using Acronis before I took the computer to the repair shop, so I have restored the image. I still have the same problem!

  Someone at - it suggestions on what I might try (other than a clean reinstall of Windows).

  Say the event viewer when you start after an accident?

  Personally I'll be back to the top of what you need and try a new installation of windows.

  Check Device Manager and see if there is something contradictory too...

  In fact what would be useful is if you can list the steps you have tried so far, so we don't waste your time with useless suggestions :)

  I'll be watching this thread for an answer, so I'll get back to you.

• Firefox is flickering and slow death after firefox update 33.0.2. How to remedy?

  Firefox is sparkling and is very very slow. Even typing is dead slow. JS intensive pages are completely slow and flickering. All this happened after updating to firefox 33.0.2. How to remedy?

  Start Firefox in Safe Mode {web link}
  While you are in safe mode;

  Type of topic: preferences< enter > in the address bar

  Select Advanced > General.
  Find and stop using hardware acceleration.

  Search web sites secure. Are there problems?

  Then restart.

• 11 Firefox crashes and is lagging after a few minutes. YouTube videos are lag while the sound is normal. Can you help me solve this problem?

  If I restart my browser everthing works very well for at least 5 minutes. When I watch several videos to youtube, the LAG comes back and the video begins to freeze aboud every second for just a fraction of a second. The sound is stil played properly it only affects the graphics...
  After about 10 minutes watching videos, the whole browser gets lag. Sometimes when I type fonts appear only about a second later. Scrolling is also affected. A few minutes later everything is back to normal, but it' not always t like that?

  I don't know what to do, I already rebooted with disabled modules, but I did not notice any difference. My ati graphics card drivers are up to date and I have the problem with firefox, chrome works perfectly.

  Best regards, Jan

  The offset is now gone. Removal and reinstallation of the plugins and the deactivation of my modules to speed dial (which is sad cause I like them) fixed. I think that's their function to auto-update the previews leading the video shift.
  Thank you very much for your quick response and your help. I appreciate it.

• Playback stops after a few seconds when streaming, slows down after a few seconds, when I look at D/L had video offline.

  Hi all

  I'm having a bit of a hairy problem - * ANY * video streaming, whether it be HTML5 or Flash stops after a number of seconds (rare) seemingly random.  YouTube, I sometimes get a buffer wheel to turn constantly, sometimes nothing.  On Facebook or other sites, nothing happens - freeze just a video.  Internet high speed or bandwidth is not a problem - 50/50 FiOS here.  Sound œuvres until frost.

  I tried to download videos in FLV Downloader, but when I look in the Media Player, they slow down until they are very bad after a period similar to the streaming video.  His work sometimes until the downturn, sometimes does not at all.  VLC plays the video at the right speed, but without the sound.

  I tried deleting and re-installing flash player, run a restore point when the video was working and all the other stuff I tried, but nothing worked and I'm stuck.  I have no idea how to solve this problem.  It happened randomly yesterday (apparently).

  If anyone has any ideas, I'd appreciate a helping hand.  I am a student that takes about half of its classes online, so without flash or HTML5 video, I'm in all sorts of trouble.

  Thank you

  Matt

  * edit * on a whim, I just open Spotify to see if that would work.  No bone.  Nothing plays.  Not at all.  The music does not play in Media Player, (local or streaming)

  Well, it seems I solved the question - I have no idea why this is happening.  I have a Logitech G35 Headset.  Sometimes when I restart Windows, I get sound out of it (usually noticed during a Skype call).  If I unplug and re - connect the headset, everything is hunky-dory with the sound and Skype.

  I just had to do, and when I did, all the videos and other media began to work very well.

  I'm cursed confused.

• Update begins and ends abruptly after a few seconds.

  A couple of days that my MS Vista equipped computer stopped seeing the enternet.  Found a ton of register of the disabled items.  Corrected enough to rise again the computer.  Since then, when I update Security Essentials, the update runs for a few seconds and suddenly turns off.  I show 15 copies of the same update and

  Essentials asks me to update again.  Help, please!

  post moved from the other thread

  support case number: 1171844295.

  Have tried several things I found on the web. None worked.

  Get Windows Update error 80073712. Windows says no error. Can anyone help? Thank you. Cannot update my computer.

  I'm moving this thread on the forum Vista/Windows Update, because this issue is much broader than just the MSE updates * and * a matter of pension has been opened, by the Po.

  -steve

• Asks the plugin noise reduction effect-made clip jerky and slow down after application?

  I apply an effect - the neat video Plugin to reduce noise. for some reason when I apply the effect, playback of the clip is really slow and jerky. Why is this?

  Hi Dragonsfire,

  I'm looking at the rendering time and it's extremely slow, like the clip is 30 secs long 2mins but render time estimate is like 3 hours! My laptop is not the fastest, but it is not no more ancient. Any suggestions on the reduction to make time-no understood them with a much more powerful computer!

  You have met one of the intensive more rendered effects on the stage of post-production. Sorry if you think that something goes wrong. Likely, that's fine, except that it takes very long time to process images with that plugin.

  Here are some tips on the neat video forum:

  The real rendering for your clip speed should be around approximately 2 images per second. This value seems normal for a HD (1920 x 1080) image size and material to the average (you don't mention your hardware specifications). You can speed up a bit by disabling some of these filter options:

  • disable the very low freq, high quality options
  • some of the fixed noise reduction in some or all channels amounts (luminance / chrominance or Y/Cr/Cb) and/or ranges of frequency at 0%
  • reduction of the time filter RADIUS
  • disable the option of adaptive filtering

  These measures allow the filter a little faster, but at the expense of the quality of filtration reduced. Noise reduction is usually a compromise between quality and processing speed. When you need good quality, it makes sense to give some time to the process with the top of the settings page. When that is not necessary, you can use a less accurate and more rapid filtration.

  Thank you

  Kevin

• Remote Desktop connects then stops after a few seconds

  I have two laptops to Windows 7.  We run OpenVPN which I will refer to the VPN server.  The other is the Client and with me on trips.  Open VPN is configured on the Client and the VPN server, and I can connect from inside and outside the network without any problems.  I also have an Open VPN Client with another port configured on a server QNAS.  I can connect without any problems.

  I want to run the OpenVPN server on one VLAN separated to prevent users to see my internal network and only sees another NAS.  I also use the VPN to offer our few users (3) the ability to connect and use my static IP address.

  I have a router TP-Link-ER-6120.  I can configure the three ports to run in 3 separate VLANS.  When I configure the VPN server works on my regular network to exploit the VLAN1 and VLAN2, I can always connect to OpenVPN and all I want to do works (NAS and Internet access with my static IP).  However, when I try to establish a Session to the VPN server computer remote desktop, I get the login and enter my user name and password.  I see the remote desktop window, open and usually see the remote desktop wallpaper and loading the desktop icons.  Then it crashes.  If he does until I can see the desktop, it automatically attempts to reconnect.  If she makes it that far, it stops with a window that says Remote Desktop connection has been disconnected.

  If I come back in the configuration of the router and change the configuration of VLAN for the server VPN is on the same virtual network, I can connect and the remote desktop connection is successful, as long as the customer is located on my network.  If I connect the Client to the VPN server from outside my network in this configuration, the remote desktop will always fail in the same manner described above.  I also have a QNAS on my network with OpenVPN configured and operational.  If I connect the Client computer to the QNAS, I can connect to the VPN server until the VPN server is placed in its own VIRTUAL LAN.

  Thus, work Desktop connections to local computers.

  However, since a remote off-grid remote office connections begin to work, but are stopped when connecting.

  -J' I ping the VPN server during connection attempts and never lose the connection.

  -J' used telnet to Server VPN 3389 port and it connects.

  -J' turned off the firewalls on both sides and went up to remove Symantec on the VPN and BitDefender server on the side side Client to use Windows Firewall on both.  And then disabled Windows Firewall as well and still no joy.

  Is there a setting in Windows I'm missing that allow the desktop connection remote on the LAN, but not enable during login remotely even if I can ping, telnet and usually access the rest of the network?

  Is it maybe a configuration problem on the side of the router?  Installation side route is a very simple graphic interface.  I configured for the VPN service roads and they remain in place (one for the QNAS) and one for the OpenVPN server.  I set up a static route (virtual server) for port 3389 go directly to the IP address of the VPN server, but that did nothing.

  Miss me probably something simple, but it launched my ass for weeks now.

  Any ideas?

  Hello Michael,

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  By the description, I understand that the problem with remote desktop connects and then stops after a few seconds on the system.

  Certainly, I understand your concern and will try my best to help you.

  To get more information about it, we have a dedicated forum where these issues are dealt with and would be better suited to the TechNet community.

  Please visit the link below to find a community that will provide the best support.

  http://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

• I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  You probably should have updated to 10.5.8 first.

  Installation or update of Snow Leopard:

  http://manuals.info.Apple.com/en_US/Snow_Leopard_Installation_Instructions.PDF

• I recently bought creative cloud, and after a few updates and downloads, my desk right icon now produces an empty rectangle if clicked. How to bring back my list?

  I recently bought creative cloud, and after a few updates and downloads, my desk right icon now produces an empty rectangle if clicked. How to bring back my list?

  I ended the application of uninstalling and reinstalling and that seems to have done the trick. Thanks for the help - it lead me to the right place