sr1403wm re - turn on my bios

Similar Questions

• Recovery (aka 'turn off system') BIOS admin password

  Hello

  I'll be very grateful if someone could help me to reset the BIOS on my HP Pavilion tx2500 admin password - I didn't use it for more than a year so the forget password of course.

  After invalid 3 attempts it displays "system turn off the key: 72015992.

  Thank you!

  Use the posted above unlock code to access the BIOS

  Disable all passwords that are enabled

  If current password request - type the unlock code

  New password, simply press the ENTER key
  Repeat the same thing to check the password column.

  Then exit the BIOS saving & exit option to save the changes.

  Concerning

  Visruth

• fan noise noisy dv6 when you turn on / prior bios version?

  I just got a brand new Pavilion dv6-2150us. I used it a few hours, with several Turn-off & ons, and everything was nice and quiet in the ignition until I flashed the BIOS to the F.1A version. Now when I turn it on - the second, I click the power button - the fan goes full bore (whooOOOOOOOOOOSSSHHHH) for 3-4 seconds, then settled into a low hum. This happens even after it sat overnight, it is not a question of latent heat. I disabled the 'fan always on' setting in the BIOS, but I still get the WHOOOOSH. Anywhere where I can find the previous BIOS and this flashback in time?

  I get the same thing on m Dv6 after upgrading the BIOS. He was supposed to "improving fan behavior" so maybe it's a function of power management where the fan will operate at different speeds what do your do, rather that running at a constant speed. It's the only thing I can think of. My GPU and CPU appear to be running a little hotter on idle but (I have a model with an i7 and GT 230 M). Who knows, he has installed fine, just different past, thus the exact improvement, I don't know.

• Satellite C855-1j4j does not turn on - the Bios Update interrupted

  Hello

  I did the update on my laptop Satellite C855-14 days, and all of a sudden the power went out,
  now the pc running either party but not nothing DON'T get PAST...

  What should do?

  + The message was edited: message has already been translated.

  From my point of few the EPROM module must be re-flashed once more with special BIOS crisis recovery disk.

  Usually, this procedure could be done only by authorized service provider available in your country.

  But I found an interesting announcement about how to flash the BIOS on U400 series.
  See the last post [here: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=62852]

  But I don't very well if this info would be useful and if it would work in your laptop to Mr. However, in case this would not work, contact the ASP from Toshiba for help

• Satellite L650 - Touchpad turn off after BIOS update

  Hello
  I recently got a new laptop, a L650-1CN,.
  I run different types of software from Toshiba, and one of them is Tempro,
  He shows me messages when a new update is available.

  Today I saw the message that a new BIOS update v.1.80 was available.
  I downloaded and installed. After installing my laptop closed. Then I started again.
  But after a few minutes, I noticed that my touchpad disable itself more.
  I usually use a logitech wireless mouse.

  Now, I wonder if I should do a system restore and not install this update of the BIOS or find another solution for this problem. Because it's really boring.

  Thanks in advance.

  Hey Buddy,

  Usually the touchpad disable automatically if an external mouse is connected, but only if you enable this option in the touchpad settings.

  I also use an external Logitech mouse and have enabled this option. You can find it in Control Panel > mouse. Go to the device settings tab and mark the internal pointing device option disable when the external USB pointing device is attached.

  I hope it works :)

• Question of updating the BIOS for Qosmio F50 - 10 k

  Hiya:

  + This Bios update adds functionality to your system. +
  + (BIOS stands for Basic Input and Output System. This program is stored in a chip memory dead on the motherboard. +
  "+ When the computer turns on, the BIOS is launched to perform various functions to start). +

  + For detailed updated information, please refer to Toshiba-setting to update BIOS Information +.

  + Toshiba - 2.00 - WIN32 Qosmio F50 +.

  It will work on toshiba F50 - 10 k, Windows xp, sp 3?

  [Notebook-> Qosmio-Qosmio series > F-> Qosmio F50 | http://eu.computers.toshiba-europe.com/innovation/download_bios.jsp?service=EU]

  Post edited by: kirekk

  Qosmio F50 - 10 k belongs to the series of PQF55E.
  If you want to update the BIOS, you will need to use the BIOS exactly for the F50 PQF55E series.

  The European driver Toshiba page provides BIOS for Vista 32-bit and 64-bit OS.
  But this does not mean that you cannot use the Win XP

  I think you can use the Win XP but the fact is that the BIOS has been optimized for Vista and not XP

  The BIOS update should work also on XP, but in some rare cases the update cannot be performed and in this case, you will need to the Toshiba preinstalled the operating system in order to update the BIOS

• HP 2570p: Virtualization enabling bios hp2570P

  Hello

  I need to enable virtualization in the BIOS, I turn on the BIOS, but when I try to install HAXM an error appeared on screen that says virtualization is NOT impossible.

  Can I activate something more in the BIOS as well? or I did something wrong?

  Kind regards.

  Ho

  I found the answer to my question:

  Of Microsoft Hyper-V must be uninstalled.

  When we Hyper-V hypervisor, installed Microsoft takes over and will not let VirtualBox or VMware access Intel VT - x, despite the VT - x hardware is installed you can not install haxm, the Hyper-V uninstalled unless.

• BIOS shows 4 GB for HP 15-E041CA E5D76UA

  Hello

  I ordered a HP 15-E041CA E5D76UA from NewEgg, however, once I turned it the BIOS displays "Total memory" like 4 GB instead of the 8 GB in the specification. NewEgg staff said because VGA use 4 GB of memory, is that OK since in VGA mode VGA shouldn't take 4GB. Is it broken?

  Thanks for your reply.

  The computer does not start... and this means that the other is wrong. If you get one and it won't start not very well and the BIOS shows 4 GB, confirmed by the permutation. You should hear a beep. This means that the module inside does not work very well. However, I would call HP and ask them to take your computer hitting stick that replaced under warranty from the manufacturer. They are 4 GB sticks!

• Satellite A-C55-1N1 - how to fix Windows 8.1 after trying Linux?

  Hello

  Laptop: Satellite C55-A-1N1

  In my infinite wisdom, I tried to install Linux in dual boot as my old laptop scenario. I have narrowed the main partition of windows in windows 8.1 first and then installed linux on this partition. After the reboot, Linux worked, but not windows, because I had to disable the secure boot and set bios to the CSM for linux to load.

  After turning on and bios secure boot to EFI, windows boot more. I tried to repair the windows operating system by running the repair of another DVD of Win8.1 tools, but they do not have repair startup. I learned eventually to zero to start takes you to the... except hidden restore partition my not!

  So, I checked the windows and the recovery partitions are intact but I can't access the recovery partition or repair the windows installation with windows 8.1 repair tools. No, I have not all backups, other images or system restore options. Clever, aren't I? I don't have the original recovery partition (which I can't access) and the windows partition to play with. I don't want to lose my license OEM Windows 8.1...

  Any ideas how to save this installation of windows?

  Thanks in advance for any help.

  You have made the same mistake as many other people. On this forum, we discussed many times how it works and tried to explain how it works.

  In s manuals are described clearly that each owner of the laptop must create a recovery (DVD or USB) media and this created recovery media can be used for recovery image installation where this HARD drive recovery option does not work or if the HARD drive is faulty and should be replaced.

  As I see that you do not have this recovery media. Is that HARD drive recovery facility can be started if laptop has only factory settings. Your experience of Linux, this option disappeared and there is no way to start it again.

  What can you do now? I know it may seem stupid now, but if you want to install original recovery image you need to order new media of recovery and it can be done on https://backupmedia.toshiba.eu/landing.aspx

• Satellite M60 - controller keyboard may be defective

  Hey all, first of all I apologize for my bad English.

  I have a Satellite M60-149, and since 2 days no longer start.
  It stops to load in the Bios Phoenix with 'Please wait' screen the fast flashing of the status bar.

  So I think that the problem is the bios error. But if I hold down Fn + ESC when I turn on, the Bios boot, then windows also.
  In windows, the mouse is OK, but keybord does not work.

  I assume that the problem is as a broken hold down the key. So I physically removed the keyboard and I try with a keyboard external usb.
  Nothing doesn't change, "Please wait" still on the screen of the bios or windows start pressing Fn + Esc to power.

  In my view, keyboard controller is damaged. But I wan't to pay 300 euros for the new motherboard.
  Anyone have other tests/solutions?

  Hi Gianluca_1,

  I m not a technician for computer laptop, but even the keyboard is removed and you get the same problem it seems that the keyboard itself isn't affected but he s strange that it starts when you press FN + ESC

  I think that in this case you need an answer to an authorized service because they can give you an official statement so I recommend contacting the guys and ask for help.

  An alternative, try to load the default settings in the BIOS and try a BIOS update.

• Satellite L750 - 22 X - fan stops working

  Replaced the fan with a new one and paste, heat sink applied, but same problem persists as in the old fan, it stops spinning randomly after 30 min - 2 hours and then the laptop turns off. BIOS is on the latest version.

  Help, please

  Hello

  The cooling fan is controlled by the fan which is stored in the BIOS table.
  It of really difficult to say why the cooling fan is not working properly, but I guess that there must be a problem with the BIOS settings of DMI, or probably with the motherboard.

  I think that the laptop must be verified by the authorized service provider.

• No boots motorcycle no G580 os

  Hello everyone, I don't know why this is happening to me. My laptop is lenovo G580 i5 4gbddr3 500 GB hard drive. There after Win10 Win7 Ubuntu14 config default os is win10. I was using the shut down windows 7 lappy and went to play. Now, if I try to launch it boote, lenovo display anything after that no boot loader screen. Hard drive is detected as I removed the battery, turn off the bios reset after boot uefi. But without success it just does not start. Linux Live USB is detected and the hard drive is also detedcted. Any help. I need in an emergency. Thanks in advance.

  I would like to use EasyBCD bootable CD/DVD to see if it can restore your bootloader files. Also go with Mint Live DVD and see if you can mount the hard drive, if tests above to see if you have failures showing so try SMART running.

  Also - good idea to back up user files / documents / music / etc... on a flash drive when running Mint of the DVD - in the case, you will need to replace the hard drive.

  Finally - if nothing else does, try to boot from the button Lenovo, go to BIOS and run the diagnostic disk, if all claire - restart and use recovery tools to take back to factory settings. This destroys all the (data) partitions on the hard drive and back to the loadout plant.

  Good luck.

  CB

• HP touchsmart 310 screen for 1 second and then black screen

  This is ridiculos, I want to say I can't believe I'm seeing, the pc shut down correctly, next day pc started acting, funny, when turn on, displasy bios screen for a second then goes black forever, trying to solve the problems he me i remove the cmos battery, it does not display black screen just after inserting the cmos battery same problem occurs , pls I need help facilitating the sky of my client a date limit and it's killing time of y. HP pls help...

  to make the light on the screen?

• Pavilion dv6 3015sa: incomplete error on restore in recovery through recovery discs

  Hello

  I have a pavilion dv6 3015sa and since I bought it, I have the recovery disks. now I want to recover my original win 7 and its drivers with his records, (I have no installed win now) I go through its process and I put all 5 lights up disk in the drive and the recovery process. When it is finished with discs, asks me to remove last disk and click on continue (and I do)

  After this system charges with no disc in the drive, but after a few seconds it stops with this error: "Restoration incomplete" and it has 3 options which nobody works. but when I press RETRY its tells me insert recovery media and I insert it, it restarts, but comes back with the same error this time when I click on start AGAIN, he said "a file without a name is not found" no matter what disk I insert. I tried so many ways, but nobody is working, I did these things:

  1 wipe the entire disk with Paragon (and I formatted the disc after that) (shoudn't I format the drive after?)

  2. turn the defult Bios (my version of the bios is F.27)

  3. remove the disc quickly before restarting

  Please help me, what should I do?

  This question seems unsolvable!

  Thank you since it is a very strange problem, nobody answered me, I fixed it by the following process:
  1. I rewiped the entire disc and formatted, it
  2. I changed the date of the bios in 2012 and he's fine now I'm back to the original win 7, the performance of my pc now are really good and does not to overheat again and I rarely hear fan noise!

• Acer aspire s7-392-9439: lack of default boot device or startup failed.

  Hello
  I bought an Acer aspire s7-392-9439 3 months ago. It has been working fine, until yesterday.
  I turn on the computer and it poped a blue screen with the error: 'lack of default boot device or startup failed'.
  This error reminded me that a message on a bios updated poped over a few days and I have the chance to install it.

  I contacted acer support, I was told that the update of the bios would have avoided this problem. Also, they told me to try things that can help, but unfortunately none of them has:
  1 restore the default bios settings.
  2. change the bios settings: uefi to legacy.
  3 type the Windows key + c when the computer starts.

  When these options do not have they said it is probably a hardware problem and I should send my computer to their repair center.
  My questions are:
  1. If they updated bios would have prevented the problem, how can it be a hardware problem?
  2 - does anyone know how to solve the problem?

  I would appreciate your help,
  Michael

  I had the same problem.  Tried the diskette of starting BACK and did not work.

  Here's how I solved it:

  (apologies to memory are some terms is not on-site)

  1. download the Setup file of the BIOS - link provided above in this thread (isST2212.exe)

  2. on a Windows 8 machine that works - search for 'Create a recovery disk' and run on a USB drive

  3. copy the file #1 to the USB drive once it's done make a recovery disk

  4. in the Acer BIOS (press F2 during startup), change to the method of priming of the legacy

  5 save and exit

  6. turn in the BIOS and move the option USB HDD as first boot device

  7. Save and exit

  8. you will end up in a Windows 8 recovery console

  9. go to Advanced Options - find the option that leads you to the command prompt

  10. from there I went to d: drive and found my file isST2212.exe - run by typing the file name when you are in the folder

  Make sure that you are connected to power - let it run.  It should install, automatic restart and you should be in business.

  I had an Acer offer to fix it for free with a 7-10 day turn around and at the risk of losing all my data.  It's a much better solution!