SR520-FE-K9

Similar Questions

• issue of nat sr520

  Hi, I have configured the sr520 using the cca.

  Basically I have a device connected to the sr 520 wireless with the IP 192.168.200.160.

  The SR connects to internet via adsl and pppoe.

  I have configured NAT to the unit for a number of ports, but it does not work.

  I enclose an excerpt from the configuration, all the ideas I have a hurt

  Instead of...
  type of policy-card inspect sdm-inspect-voip-in
  class type inspect SDM-inspect-staticnat-in
  Pass
  
  Could you do
  type of policy-card inspect sdm-inspect-voip-in
  class type inspect SDM-inspect-staticnat-in
  inspect
  I think that will fix the problem.

• SR520, ping response

  Hello

  Not very familiar with the ZBF on the SR520, can anyone please provide me with a configuration allowing the SR520 send ping reply´s.

  Concerning

  Eivind

  Zone firewall configuration can be confusing, especially if one is used to the old configuration of the CBAC-type FW.

  Your best resource for this problem is the

  Design of the area Guide of Application and firewall policies

  http://www.Cisco.com/en/us/products/sw/secursw/ps1018/products_tech_note...

  Annex B has an example configuration that would allow ping responses.

  There are four basic steps to set up the firewall.

  (1) define areas

  (2) define the class cards to identify traffic between zones

  (3) create a strategy map that defines the action to be taken in terms of class

  (4) set up the pair area and apply the policy

  In Annex B, you'll see the class map specifying which traffic to inspect. The names of the class map and policy-map could be anything.

  class-map type inspect match-any L4-inspect-class
  
  match protocol tcp
  
  match protocol udp
  
  match protocol icmp
  
  The policy map here indicates what action to take, and in this case, the only action is to 'inspect'.
  
  If it was 'drop', the connection would be denied.
  
      policy-map type inspect clients-servers-policy
  
      class type inspect L4-inspect-class
  
        inspect
  
  Hopefully that helps!
  Addis
  
  

• IOS 15 for routers SR520

  Can someone tell me when the IOS 15 will be available for SR520 routers?  I am wanting to deploy IPv6 on some of those we have there, but I can't it supported are IPv6 ACL support, which is not in 12.4 (24), the latest version available online.

  .. as a quick update:

  ACL IPv6 are included 12.4 (24) T for the SR520, but they are hidden from the help of the CLI.

  If you go ahead and paste in your ACL configuration, it will be accepted in the running config

• Cisco SR520 - no outgoing access

  This is the current configuration of the router. Can someone tell me why my (192.168.x.x) clients cannot access the internet through that router?

  See the race
  Building configuration...

  Current configuration: 10699 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname SR520
  !
  boot-start-marker
  boot-end-marker
  !
  forest-meter operation of syslog messages
  enable secret 5 $1$ K5vy$ E90Ebf679MAMz.wglbYsJ.
  !
  No aaa new-model
  clock timezone STD - 7
  clock to summer time recurring MDT
  !
  Crypto pki trustpoint TP-self-signed-1548662293
  enrollment selfsigned
  -More - name of the object cn = IOS - Self - signed - certificate - 1548662293
  revocation checking no
  rsakeypair TP-self-signed-1548662293
  !
  !
  TP-self-signed-1548662293 crypto pki certificate chain
  certificate self-signed 01
  3082024E 308201B 7 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 31353438 36363232 6174652D 3933301E 170 3039 30383231 31393030
  33335A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 35343836 65642D
  36323239 3330819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  8100B9BC 7D728F83 7D6059FD 49210310 F04FB968 4440ACD0 B16C927B 8AA215C2
  829 166FC 79F9CF75 ADAADACE 97292EA9 3C7DAFF6 EA5F6B8C 1FD00813 144DB9E8
  613744 D 47D1BCEF 344B268B 4 CBDA8579 A8B3D367 480CD3E0 687ACBF1 3E578E7A
  5583BE8C 9DD04F27 4060299E 0F212CF5 50F1F237 BDFC3CE6 87385AD8 D403A9E1
  36510203 010001A 3 76307430 1 130101 FF040530 030101FF 30210603 0F060355
  551D 1104 1A 301882 16535235 32302E64 6F6D6169 6E2E6163 7464736C 746 7030 D
  1 230418 30168014 DB9949FB 24128D3B 7528E6F3 8DBE4409 D4342BAF 1F060355
  301D 0603 551D0E04 160414DB 9949FB24 128D3B75 28E6F38D BE4409D4 342BAF30
  010104 05000381 8100B95F C4A4AC82 57974A6D 181D601F 0D 864886F7 0D06092A
  A2189179 25D9764A FBA8513B 94FC17E4 34F2D097 C40DD507 F0595CB5 B 538, 0296
  -Other - 39866542 F1DA78C0 A09B469F 739C2FB0 A54B1367 DA88ECFF D51FE907 56E8E06D
  33412A9D C9A57B60 2DAF85E1 B5A84E60 C740962B 525D72B3 883BBBC1 47A5AD4A
  F8F25292 813AEC2B BD37B55A 96A2A177 666TH
  quit smoking
  dot11 syslog
  IP source-route
  !
  !
  !
  !
  IP cef
  name of the IP-server 209.161.4.218
  !
  No ipv6 cef
  Authenticated MultiLink bundle-name Panel

  parameter-card type urlfilter SDM_URLFILTER_MAP
  exclusive-domain license wendell.k12.id.us
  exclusive-domain license mail.wendellschools.com
  exclusive-domain license k12.id.us
  exclusive-area permit www.teenbiz3000.com
  exclusive-domain license mail.safelink.net
  exclusive-domain license www.sd232.k12.id.us
  -More - exclusive mail.wendellschools.org allowed domain
  exclusive-area permit bing.com
  exclusive-domain license google.com
  license exclusive-domain yahoo.com
  parameter-card type regex sdm-regex-nonascii
  model [^ \x00-\x80]

  type of parameter-map protocol-info msn servers
  Server name messenger.hotmail.com
  Server name gateway.messenger.hotmail.com
  Server name webmessenger.msn.com

  type of parameter-card aol-server protocol-info
  Server name login.Oscar.AOL.com
  Server name TOC.Oscar.AOL.com
  Server name oam - d09a.blue.aol.com

  type of parameter-map protocol-info yahoo servers
  Server name SCS.msg.Yahoo.com
  Server name SCSA.msg.Yahoo.com
  Server name scsb.msg.Yahoo.com
  Server name SCSC.msg.Yahoo.com
  Server name scsd.msg.Yahoo.com
  -More - cs16.msg.dcn.yahoo.com server name
  Server name cs19.msg.dcn.Yahoo.com
  Server name cs42.msg.dcn.Yahoo.com
  Server name cs53.msg.dcn.Yahoo.com
  Server name cs54.msg.dcn.Yahoo.com
  Server name ads1.VIP.SCD.Yahoo.com
  Server name radio1.launch.VIP.DAL.Yahoo.com
  Server name in1.msg.VIP.RE2.Yahoo.com
  Server name Data1.my.VIP.SC5.Yahoo.com
  Server name address1.PIM.VIP.mud.Yahoo.com
  Server name edit.Messenger.Yahoo.com
  Server name Messenger.Yahoo.com
  Server name http.pager.Yahoo.com
  Server name privacy.Yahoo.com
  Server name CSA.Yahoo.com
  Server name CSB.Yahoo.com
  Server name CSC.Yahoo.com

  !
  !
  username admin privilege 15 secret 5 $1$ $9EbE 21QHkuUvg3blkmWNXibqM1
  !
  !
  --More--                           !
  Archives
  The config log
  hidekeys
  !
  !
  !
  type of class-card inspect any match of sdm-app-smtp smtp
  corresponds to the length of the gt 5000000 data
  type of class-card inspect any match http sdm-app-nonascii
  req-resp header sdm-regex-nonascii regex match
  type of class-card inspect any match of sdm-app-imap imap
  match zero-order
  type of class-card inspect all match sdm-cls-Protocol-p2p
  edonkey signature Protocol game
  match the signature of the gnutella Protocol
  match the signature of Protocol kazaa2
  match the signature of the fasttrack Protocol
  match the signature of bittorrent Protocol
  type of class-card inspect all SDM-voice-enabled game
  h323 Protocol game
  Skinny Protocol game
  sip protocol game
  -More class-map type - inspect correspondence sdm-protocol-pop3
  pop3 Protocol game
  type of class-card inspect all match sdm-cls-icmp-access
  match icmp Protocol
  tcp protocol match
  udp Protocol game
  type of class-card inspect all match sdm-cls-Protocol-im
  yahoo-servers Protocol ymsgr match
  msnmsgr msn-protocol servers match
  match aol aol-protocol servers
  type of class-card inspect all sdm-cls-insp-traffic game
  dns protocol game
  https protocol game
  match icmp Protocol
  match the imap Protocol
  pop3 Protocol game
  tcp protocol match
  udp Protocol game
  type of class-card inspect any match of sdm-app-pop3 pop3
  match zero-order
  type of class-card inspect correspondence sdm-Protocol-p2p
  corresponds to the class-map sdm-cls-Protocol-p2p
  type of class-card inspect any match http sdm-http-blockparam
  -More - match request port-abuse im
  request game port-bad use p2p
  match request port-abuse tunneling
  req-resp-violation of Protocol game
  type of class-card inspect correspondence sdm-Protocol-im
  corresponds to the class-map sdm-cls-Protocol-im
  type of class-card inspect correspondence sdm-invalid-src
  game group-access 100
  type of class-card inspect the correspondence dhcp_out_self
  match access-group name dhcp-RESP-licensing
  type of class-card inspect the correspondence dhcp_self_out
  match access-group name dhcp-req-licensing
  type of class-card inspect any match http sdm-app-httpmethods
  request method bcopy game
  request method bdelete game
  request method bmove game
  request method bpropfind game
  request method bproppatch game
  method of application for game connect
  match request method copy
  delete the method of application of game
  match request edit method
  match request method getattribute
  -More - match request getattributenames method
  match request getproperties method
  is the index of request method
  request method lock game
  match request mkcol method
  match request mkdir method
  method of application for game go
  method of application for match report
  match the options request method
  survey method match request
  request method post game
  match request propfind method
  match request proppatch method
  put request method match
  match request method revadd
  match request method revlabel
  match method revlog request
  request method revnum game
  method of application for game save
  is looking for the query method
  match request method setattribute
  request method startrev game
  match request method stoprev
  -More - match request method to subscribe
  match request method trace
  match unedit request method
  method of application for game unlock
  unsubscribe request to match method
  type of class-card inspect correspondence sdm-Protocol-http
  http protocol game
  type of class-card inspect correspondence sdm-protocol-smtp
  smtp Protocol game
  type of class-card inspect correspondence sdm-Protocol-imap
  match the imap Protocol
  !
  !
  type of policy-card inspect sdm-permits-icmpreply
  class type inspect dhcp_self_out
  Pass
  class type inspect sdm-cls-icmp-access
  inspect
  class class by default
  Pass
  type of policy-card inspect http sdm-action-app-http
  class type inspect http http-sdm-blockparam
  Journal
  -More - reset
  class type inspect http sdm-app-httpmethods
  Journal
  reset
  class type inspect http sdm-app-nonascii
  Journal
  reset
  type of policy-card inspect sdm-action-smtp smtp
  class type inspect sdm-app-smtp smtp
  reset
  type of policy-card inspect sdm-action-imap imap
  class type inspect sdm-app-imap imap
  Journal
  reset
  type of policy-card inspect sdm-action-pop3 pop3
  class type inspect sdm-app-pop3 pop3
  Journal
  reset
  type of policy-map inspect sdm - inspect
  class type inspect sdm-cls-insp-traffic
  inspect
  class type inspect SDM-voice-enabled
  Pass
  -More class type - inspect sdm-invalid-src
  Drop newspaper
  class type inspect sdm-Protocol-http
  inspect
  policy-service http sdm-action-app-http
  class type inspect sdm-protocol-smtp
  inspect
  policy-service smtp sdm-action-smtp
  class type inspect sdm-Protocol-imap
  inspect
  SDM-action-imap imap service-policy
  class type inspect sdm-protocol-pop3
  inspect
  SDM-action-pop3 pop3 service-policy
  class type inspect sdm-Protocol-p2p
  Drop newspaper
  class type inspect sdm-Protocol-im
  Drop newspaper
  class class by default
  drop
  type of policy-card inspect sdm-inspect-voip-in
  class type inspect SDM-voice-enabled
  Pass
  -More - default class
  drop
  type of policy-card inspect sdm-enabled
  class type inspect dhcp_out_self
  Pass
  class class by default
  drop
  !
  security of the area outside the area
  safety zone-to-zone
  safety zone-pair sdm-zp-self-out source destination outside zone auto
  type of service-strategy inspect sdm-permits-icmpreply
  safety zone-pair sdm-zp-out-in source out-area destination in the area
  type of service-strategy inspect sdm-inspect-voip-in
  source of sdm-zp-out-auto security area outside zone destination auto pair
  type of service-strategy inspect sdm-enabled
  safety zone-pair sdm-zp-in-out source in the area of destination outside the area
  type of service-strategy inspect sdm - inspect
  !
  !
  !
  interface FastEthernet0
  switchport access vlan 75
  --More--                           !
  interface FastEthernet1
  switchport access vlan 75
  !
  interface FastEthernet2
  switchport access vlan 75
  !
  interface FastEthernet3
  switchport access vlan 75
  !
  interface FastEthernet4
  Description $FW_OUTSIDE$
  DHCP IP address
  NAT outside IP
  IP virtual-reassembly
  outside the area of security of Member's area
  automatic duplex
  automatic speed
  !
  interface Vlan1
  no ip address
  !
  interface Vlan75
  -Description $FW_INSIDE$ more.
  the IP 192.168.0.1 255.255.252.0
  IP nat inside
  IP virtual-reassembly
  Security members in the box area
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 FastEthernet4
  !
  IP http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  the IP nat inside source 1 list the interface FastEthernet4 overload
  !
  IP access-list extended dhcp-req-enabled
  Remark SDM_ACL = 1 category
  allow udp any eq bootpc any eq bootps
  IP access-list extended dhcp-RESP-enabled
  Remark SDM_ACL = 1 category
  allow udp any eq bootps any eq bootpc
  !
  access-list 1 permit 192.168.0.0 0.0.0.255
  -More - access list 100 remark SDM_ACL category = 128
  access-list 100 permit ip 255.255.255.255 host everything
  access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
  !
  !
  !
  !
  !
  control plan
  !
  connection of the banner ^ CSR520 basic Config - MFG 1.0 ^ C
  !
  Line con 0
  local connection
  no activation of the modem
  line to 0
  line vty 0 4
  privilege level 15
  local connection
  transport input telnet ssh
  !
  max-task-time 5000 Planner
  end
  -More-
  SR520 #.

  OK, I heard about this once before, where the default basic configuration has been changed at the beginning of the life cycle of this product and WAN access problems were solved using a newer base from config.  Depending on your router, I have attached the default config, you can start with (or compare to yours).

  I'm not sure what has changed (I'm sorry)

  https://www.myciscocommunity.com/docs/doc-5167

• By default the SR520 impossible

  I can't the router to work at all. I want to default. CCA leaves me no default configuration for this router for some reason any. The box reset config is missing.

  I backup upward configs using tftp and then copied the config to factory V9 to the router.

  I made a flash copy start then the new mem config then wr

  When I reload the router an automatic backup and copy the operation during the start-up

  So I did the process again and then made a copy start run and had all kinds of errors.

  What exactly is the default method of the router

  I'm really starting to think that you should go directly to the TAC. Looks like you had 3 separate issue with this SR520.

  Your other post, it seems that we have:

  (1) SSL VPN connectivity problems

  (2) port forwarding problems

  (3) Config reset problems

  I'm looking what whether in the common COUNTRY assessment that could contribute to the problem here, but I don't not nailed all the answers yet.  (and I hate the idea that you're waiting on something useful here and it does not come fast enough)

  I'm still digging.

• 'How to' set up a VPN between a UC540 and a SR520 with remote IP extension

  Hi all

  I need help in establishing a link between a head office UC540 and a distance SR520 I want to use a PC and an IP phone in. This remote site is the first of many.

  I found several examples of IPsec VPN site, but none with references to some VLAN voice and data, should I worry or the phone will only work.

  All the tips and suggestions accepted with gratitude,

  Jerry

  Here is an example of configuration LAN-to-LAN VPN between 2 IOS routers:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080194650.shtml

  Assuming that your example:

  VLAN 1 - data - 192.168.19.0/24

  VLAN 100 - voice - 10.1.1.0/24

  And on the other side:

  VLAN 1 - data - 192.168.20.0/24

  VLAN 100 - voice: 10.2.2.0/24

  The crypto ACL would be:

  access-list 150 permit ip 192.168.19.0 0.0.0.255 192.168.20.0 0.0.0.255

  access-list 150 permit ip 10.1.1.0 0.0.0.255 10.2.2.0 0.0.0.255

  Crypto ACLs on the other side are the following:

  access-list 150 permit ip 192.168.20.0 0.0.0.255 192.168.19.0 0.0.0.255

  access-list 150 permit ip 10.2.2.0 0.0.0.255 10.1.1.0 0.0.0.255

• Feature SR520 DMVPN problem

  Hello people,

  I have a serious problem with SR 520 and feature cisco router, what is written on the paper!

  On the cisco site, I found that SR 520 support DMVPN, I ordered the router and it came with IOS:

  (SR520-ADVIPSERVICESK9-M), Version 12.4 (20) T6. Later, I found that it does not support

  Protocol PNDH, which constitutes a basis for DMVPN feature and speak-to-speak of VPN tunnels.

  I guess that the problem is in the IOS version that comes with the router.

  Tell me please, if you know, is the problem and the IOS version which should choose?

  Should I take later (12.4.24T6) or some special release?

  Thanks in advance,

  Vladimir

  Hi Vladimir

  Support DMVPN on SR520 was indeed only added 12.4 (24) T so I suggest you go for the last, which is 12.4 (24) T6.

  HTH

  Herbert

• SR520 VPN

  I have a router 2901 ISR in the main site. I want to build a site to site vpn using a SR520W-FE-K9 to the branch.

  I want to know if the 2901 <--vpn--->vpn site to site SR520w is possible.

  Thank you.

  Yes, without a doubt is possible to establish VPN site to site between 2901 and SR520W routers.

• DVP-SR520 how to unlock the lock on DVP-SR520P

  Hello

  I cannont find SR520P manual on Sony support, I need to turn off the child lock, I tried the procedure described in the manual of SR510P, but they do nothing. Its a surprise that the owners manaul is not on the site of sony, taken in charge is limited. In addition there is no support for DVD title, posted under blue-ray, assumed that sony are not interested in the technical support of the products back.

  Hi scotty1511,

  While the player is on, press and hold the RETURN, ENTER and POWER button on the remote control to open the drawer.

• Vs SA 520 520 SR

  Hello

  What is the diference between the family series SA 520 and SR 520 series family?, technically of course.

  Thank you

  Rolando

  Here is a list of major differences between the SA500 and SR500 series:

  • SA500 series and the SR520-T1 are considered Small Business Pro products, while the SR520-ADSL and SR520-FE are considered traditional Cisco products.
  • SA500 platform based non - IOS-, while all the current models of SR500, including SR520-T1, are based on IOS.
  • The SR520-ADSL models SR520-FE are supported by the traditional TAC and SMARTnet service is offered on these models, while Small Business Pro services are offered on the SR520-T1 and SA500 series.
  • SR520-ADSL, FE-SR520 and SR520-T1 models are designed to be configurable CCA, but have characteristics that are not configurable of CCA. SR520-ADSL and SR520-FE models have made improve the features which are not available on UC500 series / SA500 series (but which are available on ISR platforms). On the other hand, the SA500 is not configurable in CCA again (even if the basic configuration of the SA500 has been added to the CCA 2.2.1 and later versions).
  • The SA500 supports QuickVPN and SSL VPN, while the SR500 series supports easy VPN, AnyConnect VPN SSL technology and the Web SSL VPN.
  • The SA500 supports ProtectLink Gateway, and the SR500 series doesn't support ProtectLink Gateway.
  • The SR500 (and UC500 and ISR platforms) supports the routable IPsec VPN tunnel interfaces, while the SA500 does not have routable IPsec VPN tunnel interfaces. However, the site-to-site VPN are always supported on the SA500.
  • SSL VPN on the SR520 series (and the ISR platforms) requires a separate VPN SSL license, while the SA520 is bundled with 2 licenses of SSL VPN client (Extensible to 25 licenses of SSL VPN via a license update) and the SA540 comes with 50 SSL VPN client licenses.
  • The SR520-T1 is supported in the CCA multisite Manager, but the SR520-ADSL, SR520-FE, SA520 and SA540 are not yet supported in the CCA multisite Manager.
  • Whereas the SA500 platform had known bugs and was unstable at the time of its release, the platform based on IOS SR520 tends to be more stable. There was even some first SA500 customers who were planning on trading in their SA500s to the traditional products of Cisco because bugs found in the SA500 firmware release of SA500 versions. Bugs on the UC500 platform tend to be in the communications unified in the characteristics and safety components.

• Replacement for an AM200/RV042 configuration?

  My trusty AM200 modem died and it apears it is no longer available.  I thought that the AM300 looked ok but I can't one of these no more, at least not in Europe.

  I have it used to power the internet to my RV042 and then on my WRVS4400 and a few of WRT54GL and it was awesome.  It is difficult to try to find a replacement.  I tried a D - Link DSL-320 b, because it resembled a similar product, but it does not work.  In the United Kingdom, the modem needs to do all so we only PPPoA authentication.  The D-Link will do but if DHCP is activated it automatically falls in half-bridge mode but the RV042 won't work with it in this mode.  I used my AM200 half-bridge, just for try earlier but did not like the fact, became invisible on the network, so it could not be easily given but I don't know how it should work.  The DSL-320 with disabled DHCP does not give the RV042 port WAN IP to MAC cloning should fix it, is not so I am stuffed as they say.  Also, if you Google DSL - 320 b, PPPoA, routers and UK ISP you would not have bought one in the first place.  Fortunately, it was cheap!

  My work is about using a Netgear DG834PN with wireless off and DMZ active (with active DHCP and functioning properly to give the RV042 a WAN IP address, but without interfering with the RV042 the DCHP) feeding the WAN port.  It works well but does not give the same speed of line like the AM200.  Also, he loses the lock from time to time and must be restarted so that is a temporary solution.

  It doesn't seem to be many products out there, so I'm open to suggestions.

  Furthermore, the Forum configuration has changed since my last message for the Linksys one, so if there is a better Forum for this question please suggest what he.  Thank you

  Graeme Smith

  Graeme,

  This forum is specific to the Cisco Small Business product range, like the RV042 you.  In the closest Cisco Small Business portfolio, we would have to the modem AM200 ADSL is the Secure Router 520 (SR520), model ADSL (SR520-ADSL-K9).  There is also a wireless version of the router that should be required (SR520W-ADSL-K9).  I'm not familiar with the AM200 personally however the product match nearest you, we in small businesses is the SR520.  To read the the SR520 line sheet, click here!

  Hope this helps,

  Glenn

• Replacement SR520W-FE-K9 AC adapter part number

  Someone at - it helps me to get the part number on the AC Adapater and reference numbers we AC adapter power cable to the router SR520? I have a client who has both "lost" and needs a replacement. Any help is appreciated. I searched all over the documentation for Cisco for the part number, but couldn't find a CAB - AC2, which seems not the adapter power cord only.

  Thanks in advance for your help.

  Hi Michael,

  The uses of SR520-FE the same food as the 870: PWR-850-870-WW1 =

  This can be used with a power cable 2-pin CAB - AC2

  Hope that helps,

  Andy

• Router Cisco 877M ability to use UC technology?

  Hi all

  Router Cisco 877 M can cause functionality or the ability to use VOIP technology or UC?

  See you soon,.

  In the Cisco Small Business portfolio, we offer Smart Business Communications System (SBCS), which is a suite of products providing small business with UC.

  This includes remote teleworkers, namely SRI 871W and the SR520, if you need ADSL interface.  This includes the management GUI and configuration using the CCA (Cisco COnfiguration Assistant).   This suite of products have been designed and tested to work together and supported that was as well.

  You can introduce other products and attempt to interoperate, but you will drift away from the value added by sticking to patterns and best practice deployments, we recommend you.

  More on 8xx SRI:

  http://www.Cisco.com/en/us/products/ps6202/index.html

  More SR520 on:

  http://www.Cisco.com/en/us/products/ps9305/index.html

• Block URLs and instant messaging applications

  Hello

  I'm on a UC540 that I installed the customer of the United Nations and it would like to be able to block access a certain web sites and instant messaging applications type live Messenger.

  I think pour ca url blocking should happen at the level of the ACl but is not at all an expert I don't know she procedure put in place to achieve this. Idem pour applications.

  I saw that by switching the FW from one level to the other, it blocks certain services or not but I do not know what create or modifier.

  If someone has an idea, I want although it me informed because I think that this is a request that is not unique, and so I will have to reproduce on other facilities.

  Thanks in advance,

  Roman

  Hello Romain,.

  Yes, url filtering is not available in the UC. However it is available the of SR520 and with VAC.

  Hervé