SSD drive update

Similar Questions

• IdeaCentre 300 - ish - need to update information SSD drive

  Hi, if at some time I wanted to install an internal ssd drive in my Lenovo ideacentre 300-20iSH can you give me an idea on how to do it? Thank you

  Mod edit: additional information added to the subject for the clarity of the question line.

  You need a caddy for SSD support.

  http://muchorepuesto.com/es/hdadap25a35-HDD-Adaptadores/1369-Adaptador-Soporte-Caddy-HDD-25-a-35-par...

  Kind regards.

• Update: change of hard - ssd drive

  Product: computer hp laptop dv4 1220 US
  I'm lucky my HARD for one SSD drive, but I can not found in bios setup how to change sata ahci mode.

  The computer is configured by default to ahci... nothing to lose with. Install the SSD and good luck!

• Re: Tecra R950-18F: win 8 Pro starts a new SSD drive

  Hello

  Having a few issues with the victory 8 DVD pro included with my laptop.

  BIOS is set as UEFI + secure boot, win 8 pro dvd starts and I can start recovery, after a while, he asks disc 2 and starts to recover win 8.

  After completion and reboot, it does not start and shows just the toshiba logo.

  Factory hdd with SSD OCZ VERTEX 4 is replaced by the bios.

  What could be the problem?

  > Drive HARD factory is replaced with SSD OCZ VERTEX 4 recognized by the Bios.

  You have the same start-up problems 8 win using the original HDD equipped Tecra R950?

  From my point of view, it would be possible that this laptop does not start successfully because of the new SSD.

  I recommend you check the previous HARD disk.
  If the laptop could start correctly, the problem is related to the new SSD drive.

  In some cases, it would be possible that the SSD firmware must be updated.

• Satellite R830 - support Sata III for SSD drives

  Hello

  Why Toshiba Satellite R830 does not support Sata III, although the plug to motherboard. indicate that it is possible?

  So you can not significantly increase the performance of your laptop by replacing the HARD drive with disk SSD Sata III. Is it possible to activate the Sata III (6 Mbps) on R830?

  All the system settings? It's also kind of bios update request necessary support SSD and SATA III...

  Any help is appreciated! :)

  > It shows that SATA III is supported, but when you install the SSD SATA III disc it does not work with higher speeds to ~ 250 MB/s (cases Crucial M4).

  From my own experience many SSD readers need a updated firmware that is provided by the manufacturers of SSD drives.

  But readers in the R830 SSD seems to support these specifications:
  Host interface: Max 300 MB/s
  Reading data supported: Max 250 MB/s
  Writing data supported: Max 160 MB/s

  By the way: the R830 supports a Mobile Intel HM65 Express Chipset and the chipset supports the storage interface high speed supports up to 6 Gb/s transfer rate for improved data access. Provides up to 6 SATA ports, 3 Gb/s with up to 2 ports support 6 Gb/s transfer rate.

• Satellite R630 - 11L - sometimes did not recognize the SSD drive

  Hi all

  I have a portable Satellite R630 - 11L and I just bought a Corsair F120 SSD for her, but my laptop a few times did not recognize the SSD drive and fails to start occurs. I searched on the Internet concerning the issue, but there are any topic related to my problem. in recent days, I have updated my bios but the problem remains. for example if I put the computer to sleep and he never wake ups as it should be. the blue windows screen 7 failure comes and an error message 'could not access the windows volume. If portable succesful started without problem occurs until I reeboot the computer. so most of the time I have to restart computer about 5 - 6 times to work normal. At the same time, I opened a topic on the corsair website. They told me to test my drive on another computer, so I test it on laptops, dell and hp to my friends, but there is no any problem don't like this.

  So I test my ssd on an another toshiba laptop R630 which has a different hardware configurations, the problem remains that laptop too...

  So I think toshiba may provide a bios update to fix this problem. This laptop really great, so I don't want to buy another.

  y at - it advice to solve this problem?

  concerning

  Hi machka,.

  > I think that here is the toshiba support forum. is not here?
  Here he s a Toshiba forum, that of right, but you can only chat with normal users like you and me. You will not find someone from Toshiba here.
  The forum is provided Toshiba but for Toshiba users to exchange experience on different products.

  So I think that the Quad is just. No one can say that every SSD is compatible with all computers. You need to understand this!
  There are hundreds of different players and computers on the market and I m sure that no one can test a new computer with all SSD on the market. This is not possible, because it takes a lot of time and more expensive laptops that I think.

  So if the SSD doesn't work, there is nothing that you can wait for the BIOS update.
  Otherwise, you must purchase another SSD. Alternatively, you can ask a service provider allowed in your country, maybe that technicians have already experience with some SSD in Satellite R630. Just ask for that, they are the first contact for you! :)

• Satellite A500 - 14K does support SSD drive?

  Hello everyone,

  I'm considering buying an SSD to replace the old hard isk of my Satellite A500 - 14K with an SSD.
  I have a question: it's going to be that simple:
  -excerpt from my old hard drive
  -Insert the SSD 2.5 "
  -use the recovery DVD to reinstall vista and w7

  Is this laptop * tatooed * which would prevent this kind of replacement?

  a s SSD not as expensive as it was a few years ago but it is still expensive and I don't want to buy an SSD that I can't use!

  Thanks for your answers,

  Olivier

  Hello

  In most cases is not a big problem for the SSD drive works correctly.
  I made these updates on my old Toshiba laptop and it worked normally.

  Sometimes, it would be possible that an SSD would not be recognized in the BIOS. Such compatibility problem could be linked to the SSD drive firmware, but it happens in very rare circumstances

• Satellite A100 - compatibility SSD drive and recommendations?

  Hello.
  I want to replace the original HARD drive in my Satellite A100-811 with an SSD.
  What are the parameters for search? I can just about any 2.5 "SATA II SSD on the market?
  Intel X 25 - M Mainstream SATA SSD 160 GB G2 is compatible?
  Are there recommendations for Toshiba?

  Thank you!

  Hello

  A100 controller SATA HDD support.
  Generally, it should be possible to use the laptop as part of a SATA SSD drive.
  But I also read that not all laptops can properly manage the SSD drive.
  In some cases the SSD update the firmware of the player might help.
  So I can't say with certainty that the new SSD will work properly and that the BIOS would properly recognize the SSD.
  I think you'll need to test the SSD drive
  You could order it on Amazon and could test, in the worst case you could send again
  I did it too with some RAM modules that didn t work in my notebook.

  Please post some details if these updates succeeded or not, it would be interesting to know if you can use it in your A100 because I would use a SSD drive too

• Portege R830 - 111 BIOS can not find the SSD drive

  Hello
  Four days ago, I bought R830-111 [PT320E-00X00XPL] and a - DATA S599 2.5 "SATA II Solid State Drive 128 GB to replace the standard HARD disk drive. Unfortunately, the new SSD drive does not work with this laptop.

  Several times, after several reboots disc was visible in the BIOS.
  But there is not the possibility of a normal use of the SSD.
  I have day laptop BIOS [BIOS360_EC140_WIN] and SSD drive. That did not help.

  Can someone help and tell me how to work this SSD ADATA and Portege?

  Best regards

  Have you checked if the SSD drive needs a firmware update?
  In some cases, this is necessary, but in the worst cases, the SSD drive might not be compatible and this means that you need to test another :(

• Conversion of SSD drive for the reader to boot on m7 with Win8

  I just bought a new m7-j020dx (product code E4S19UA #ABA) with Windows 8 from Best Buy.  Unfortunately, it came with a standard hard disc (HDD), and I would like to install a Solid State Drive (SSD).  I have an Intel 320 and 530 series-reader.  But I was not able to get a bootable from that disc.

  The first thing I tried was cloning the drive to plant on a new disk of 530 series using AOMEI Backupper.  I got an error writing on the partition of the third.  I thought that maybe the drive was bad, so I tried again with an Intel 320 series SSD drive.  Same mistake.

  The next attempt was to clone the disk to another disk of 1 TB (connected via USB), reduce the main partition with MiniTool and clone of the 320 series SSD.  The cloning went well.  However, with the new installed SSD, the computer will not start, and I get "Error0x0000225", something about a file not found.  Disable "secure starting" in the BIOS setup has not helped (I did after the clone).

  So I thought I would do a clean install of win 8.  I generated a recovery on a 32 GB USB SanDisk player disc using Win8 recovery disk generator (as indicated on the site of HP).  I then ran the program of recovery out of the USB drive and after a few hours of software installation driver and several reboots, I get a message from HP, indicating that the installation was not complete.  Reinstall did not help.

  I don't know what the problem is.

  What the recovery disk USB one made from the original bad HARD drive (we get only a single shot at it)?  Do I need media of the order of HP on disks?  Are there problems with the use of SSDS on those computers?  Should I not a BIOS settig correctly (UEFI)?  Is there some Intel storage drivers clutter it?

  I think my next step will be to create a disc Image and place it on the SSD drive.  But I doubt that this solves the problem with the start to it.

  Another option might be to build fresh using Win8 media, then download and install each driver from the HP website.

  Any ideas out there in the land of the experts?

  Vachsen wrote:
  

  Thank you, erico, for advice.

  I tried this with 320 (160 GB) series and SSD 530 series (120 GB and 240 GB).  Actually, I have not tried on the 240GB again, just two other. . The 240 GB SSD is the best candidate. During cloning, using a larger SSD is the best for worms down the road when other programs are installed.

  So far, I've done everything suggested this that caramel:

  -Updated the BIOS for later: F.43. 03/01/2014 (HP support site).

  -Installed Intel Rapid Storage Technology v. 12.9.0.1001 (taken from the Intel site).

  -Updated the firmware of the 530 series 120 GB using Intel SSD Toolbox v2.0.10 of 06/20/2013 (from Intel).

  -The series 160 GB 320 firmware was up to date.

  -Installed the Data Migration Software Intel v. 2.0, dated 29/04/2013 (taken from the Intel site).

  -Updated environmental Support UEFI v5.3.3.0 dated 26/09/2013 (on the HP support site)

  -Enabled secure boot.

  Even using Data Migration tool Intel did not work.  Before Support UEFI environment, data migration tool would go to the step to reset but does not start what whether manually or to another.  Support UEFI environment, the software says simply "Operation failed." Following the manual data migration softwarecan be a bit tricky. There are a few things about the bootind of the Acronis loader * which must be carefully designed for the operation to succeed.  Intel also has a forum which can help as well.

  
  

  When I hit F10 and in the Configuration of the system, the Intel RST is not available.  So I suspect there is something not right here. The suggestion of updating the BIOS of caramel didn't across before it was made. It was not necessary and therefore not a good plan. I suggest that you use the Diagnostics UEFI and rollback to the previous BIOS. If you need advice with those just let me know. I have a few images that should show you what you should see. 

  A number of things, I noticed I did upgrades:

  -The site of HP support for my computer has Intel Rapid Storage Technology 12.0.7.1002 v, dated 30/06/2013 is earlier than on the Intel site.  Maybe I should roll back. That must be rolled back to the version shipped by HP. I see you introduced makes as stated in a previous post.

  -The HP support site has two distinct "RST", storage technology products a quick and a quick start technology.

  Intel has "RST" next to their rapid storage technology, so I might be confused.  I have installed the driver of the technology of quick start on the HP support site so if it is not already on the computer, perhaps it is not running and is the "RST" which is the missing piece.  In fact, same caramel said I need fast boot technology driver and then linked to download Rapid Storage Technology driver. Do not pay attention to what it says caramel.

  Here are two of the same?  Support site of HP with two drivers and version numbers, I suspect not.   Any ideas would be useful.  They are indeed different.

  The Intel Rapid Storage Technology softpaq sp61600.exe driver provides NCQ (native command qeueing) features for the SATA controller.

  The Intel Rapid storage Technology driver softpaq sp61325.exe is supposed to improve the SSD or mSATA consumption of hibernation and also imrove the resume from hibernation.

  You can't even consider installing either softpaq to clone the drive. It is always better to keep things simple.

  The SATA cable USB you use has two connectors usb at one end?  It is necessary to provide enough power for the SSD for data migration is not. Connect each usb connector to a different usb port.

  Dan

  Intel also recommends the free use of third parties such as cloning utilities

  http://www.EASEUS.com/disk-copy/

  http://Clonezilla.org/downloads.php

  http://www.partitionwizard.com/products.html

  EASEUS is, in my opinion, the best of the three.

• have replaced my HARD original with an SSD drive, but now my laptop does not recognize HP support assistant?

  Dear Forum,

  I replaced my original HARD with a SSD drive, but now HP support assistant recognizes my phone? The program runs but updates always fail and when I look at general specifications the serial number, product name, number of product, microprocessors, system memory, motherboard, bios system, drive hard (s), and optical drive (s) are all empty. Interestingly, it recognizes the device to display (s) as being mobile intel (R) HD graphics and current resolution of 1366 x 768 and refresh rate 60.

  My laptop is an Australian model HP DV4 3029tx, which is an intel i5 14 "(2ème génération) with AMD graphics 6750" I replaced the original 640 GB hd with a 180 GB ocz vertex 2 using acronis to clone the drive.

  I would be grateful is anyone know how to get hp support assistant to recognize my computer.

  Thank you very much

  Hello
  Try this: http://h30434.www3.hp.com/t5/Desktop-Operating-Systems/HP-Support-Assistant-not-working-on-Win7/m-p/736511#M34734
  I think that cloning might be the question because the original configuration has been changed. Simple uninstall and reinstall again could possibly solve the problem as well...

• Spectrum XT 13: Spectrum HP XT 13 2215TU SSD Drive upgrade

  Is it possible to upgrade SSD drive en 128 GB to 256/512 GB?

  Would update the warranty?

  See page 35 of the manual here:

  Manual of spectrum

  Yes, you can switch to a 512 GB SSD. This is the form factor that you need:

  

  This is an image of the drive 256 GB HP 689955-001 part number

  You may install this:

  http://www.bhphotovideo.com/BNH/controller/home?O=&SKU=1123186&gclid=CKH8hqXby8cCFQ2OaQodtk8Gjw&is=reg&m=Y&A=details&Q=

  Let us know if you need more information. It is quite a difficult question, and this to jeopardize security. HP would not save you if something is broken in the process, but the warranty will remain if you remove without damage.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Aspire One d255 does not recognize the usb connected external ssd drive

  I want to replace the original HDD 160 GB with a 120 GB Samsung ssd 750 evo but bios and win 10 does not recognize the ssd drive as an external drive connected via a usb connection, so I couldn't create an image of my internal hard drive.  Is there a way to clone my hard drive SSD, so I can exchange the disc later?  I need to update the bios, install a missing driver, etc. ?

  I used two different connections: one is a 2.5 "SATA case disc that I used with a disk 2.5" HARD and works very well with the HARD drive and the other is SATA/IDE connector combination with cables for SATA and power and none of these works.  I read in another forum during my research that the Aspire One d255 doesn't recognize any external SSD connected through a USB either.  Since my netbook has no data, and I had just a pure 10 Windows installed on his drive HARD internal, I removed the 160 GB HARD drive and replaced by a 120 GB SSD and installed another Windows own 10.  It worked and my system boots now in less than 20 seconds.   We can close this thread now since I now have a faster machine fully function.  Thank you!

• Application of NEWBIE - SSD firmware update help

  Hello

  New Member looking for advice on where to start with maintenance of Sandisk ssd firmware update.

  I use an SSD on an acer AOD270 netbook. So, small screen, no CD drive etc. I couldn't not, fo are the life of me, get my Win7 starter HDD cloned on the SSD and start with reliability.

  I made the big jump, installed the SSD, installed Linux Mint with all faults, made a few adjustments and controls for noatime and trim and I am very satisfied with what I have.

  I would now like to update SSD firmware. I searched these forums and a couple other places, but I'm still a little lost. Y at - it a kind soul who can tell me the right place to start or a thread where this issue has already been resolved?

  I would be very grateful. Thanks in advance.

  The SanDisk SSD dashboard notifies you when FW updates are available, but it is for Windows only. Since you are on Linux, you can keep a watch on this forum. If a FW update is released it will be posted and stickied at the top of this map. They will post a link to the ISO standard for the FW. You can burn it on a CD or create a USB bootable out of it. Below, a message from FW update for the Extreme Pro SSD for an example. There is currently no FW for the Ultra II SSD update.

  http://forums.SanDisk.com/T5/SanDisk-Extreme-Pro-SSD/firmware-update-X21200RL-released-for-SanDisk-E...

• hpdskflt.sys of loading for unnecessary ssd driver

  Windows 7 64-bit sp1 does this driver

  hpdskflt.sys

  What is useless for one ssd drive. I tried to remove it from sys32 but computer BSODed. Where this driver comes from the bios, registry, etc.?

  Thank you.

  I found the answer that's coming from the BIOS HP and land in the registry. Suggestions on how to remove it would be appreciated.

  Thanks for the reply. I forgot to mention in my post that I replaced my original drive with an SSD. If I didn't like the idea of a file .sys running for the reader who clearly didn't have mechanical protection. I have no idea, but if the pilot was originally a useless, but little problem for the SSD then I tried to stop.

  I found the answser: replace accelometer.sys .xxx and the same dll .xxx. Go to the Device Manager, expand System devices and uninstall "sensor protection". Who did.

  Now Windows Update asks me to replace the driver. I just ignore and see if there entry registry to remove.

  Problem solved from my point of view.