SSD Ultra II read &; write speed problem
Hello world
I'm hoping to get help please about an SSD, I just bought and do not seem to be getting anywhere near the advertised speed it is supposed to be able, I only spent by technical support yet as thought someone here might know the answer.
I bought the Ultra II capable of up to 550 MB/s write in reading and 500 MB/s, but after doing some 480 GB testing the 3rd party software and the State of SanDisk my speed to read dashboard is about 346 MB/s and writing is about 236 MB / s, is not anywhere near the announced speeds.
I made sure the drivers are up to date in the dashboard, checked my motherboard and confirmed he has 2 SATA2 and SATA3 2 ports, bought new cables SATA 6.0 GB of data and made sure that they are plugged on SATA3 ports using the manual of the motherboard, but I get still only these slow speeds.
Any help anyone can offer would be great, thanks.
What is the MB brand and model? Some MB have several SATA 6 GB ports on different controllers. Intel SATA chipsets tend to perform best. I have a MB with Intel and AS Media SATA 3 chipsets and I see the same performance you see if I connect an SSD SATA 3 ports that use the controller AS Media.
Tags: SanDisk SSD
Similar Questions
-
Hello
I want to know how read and write speed of the last GEN TC?
It varies a lot in fact.
My TC Gen5 is written rather slow... 20 Mbps but playback is ok... around 40-50 MB/s
Of course, it is via ethernet and is speed of copying a single large file. Several small files will go much more slowly.
-
Satellite A80 129 DVD-RAM write speed problem
Hi all!
I have a problem. the thing is that I want to write in NERO 6 (last version purchased) a CD or DVD, but we will only write to me at slow speeds. In this laptop I MAST * a DVD-RAM UJ-830 s with DVD-R 8 x and 24 x CD - R write speed said.
When I try to write on a CD it gives me only 16 x write speed, then where is x 24? It goes same for DVD, as I want to burn DVDs and it gives me only 2 x write speed.
Please, do not put this fault on a CD or DVD, cause in my country there are limited suppliers of this type of media, so I won't change my media. They worked with my previous PC CD - RW fine, no speed problem.
I want to know also if this is lack of DVD - RAM, where then find firmware for this burner?
Thanks for your replies.
BR, Kekec
You should try to update nero, it might solve the problem.
Also an update of the firmware can help, go to http://www.toshiba-europe.com/storage/index.asp?nav=HOM&page=HOM&frame=home
-
Dell XPS 600 read/write DVD problem
My system is a Dell XPS 600 and has a DVD/ROM drive & a DVD RW. The drive works fine, but the DVD RW will not read/write or recognize a disc is inserted. The original drive failed when running normally with WIN XP. I replaced the drive (w/Lite-on SOHW 1633 s), responsible for all the latest drivers, flashed the firmware of the disc and nForce4, changed discs and cables, from Win XP to WIN 64 bit with the same results. The drive won't work, except when I insert the boot disk WIN XP drivers he will read and open the files as it should. Can you help me?
Osprey4,
I think you're right. The new drive is the problem, and I'm going to get another to confirm.
I changed discs and the RW still does not work.
Thanks for your help.
jdm05klm
-
Wireless AC slow (and different) read/write speeds
Hi all
I just bought a new Mac Mini and unfortunately it is too far from my media server to run an ethernet cable (I just moved) so I use an Airport Extreme (new model with AC Protocol). But the read speeds seem to be slow I can't broadcast some movies from high on the server bandwidth. I tested the speed of transfer, and it seems that I get the following:
READ: 24 MB/s (or 192 MB/s)
WRITE: 8 MB/s (or 64 Mb/s)
Can someone explain to me why these speeds are not the same? And should not be a lot faster? I get full signal and I joined technical details if this helps to explain anything. I would like to know what speeds you guys get with your Airport Extreme.
Thank you!
How far is your Mac to your server?
There the walls or something in the line of fire?
Have you tried the 2.4 GHz connection instead?
-
Hello
I am facing an active time for intermittent drive 100% with 0 kB/s reading or writing speed with my G3 450 ProBook running on 10 to win.
Meanwhile, the laptop does not. This effect always lasts exactly 60 s (visible in the Task Manager), and after that, the hard drive still responds once. Looks like some kind of timeout that happens after 60 seconds before returning to normal behavior. Sometimes the 100% active time occurs every few minutes and sometimes I can work for hours without interruption. So far I was not able to trigger the effect.
A Google search on "100% active time" returns a lot of suggestions like disable the superfetch, windows search, and the background intelligent transfer service. None of this solves the problem. The hard disk drivers (Toshiba) and the (Intel) SATA controller are up to date. I already reinstalled Win 10 who do not help either.
I have another problem with this ProBook. I don't think that this is related to this problem. However, you never know...:
I'm out of ideas. Any input is highly appreciated.
Thank you
Martin
Well, in the meantime, I found a solution... I bought a new HARD disk that is supported to win 10. It's a little embarrassing that HP sells the laptop with Win 10 and it does not work as it should. But anyway: problem solved.
-
Re: Satellite A660-15t - read/write Bluray problem
Hello
Is it possible to burn a blu ray laptop drives that will play on normal (IE sony blu - ray player connected to tv) blu - ray player? I wrote discs in both formats available in the menu "burn", but neither will play on the sony reader. However, they will play on the laptop.
Any help appreciated
Thank you
Simon
Hello
It is possible that you external Bluray player is not compatible with the disk used for burning bluray
It would also be possible that you tired to copy a bluray disc when the content (film) is protected against copying of blurays wouldn t -
How do you know the speed of read/write of a flash drive?
Who knows a program to read/write speed?
Hi Cristi,
Thanks for posting in the Microsoft Community.
An indication of the standard flash drives read/write speeds is the following:
USB 2.0:
Sequential write speed range = 4-10 MB/S
Sequential read speed range = 15 to 25 MB/S
USB 3.0:
Sequential write speed range = upto20 MB/S
Sequential read speed range = upto45 MB/S
These reading and writing speeds offer a guide to the read/write Flash Drive performance and have been identified in recent tests. Please note that we are changing the components USB Flash Drive at any time based on the availability and cost. This means that the read/write speeds above cannot be guaranteed.
You can use your favorite search engine to search for this application that measures the speed of read/write of flash drives.
Warning: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.
Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.
-
Sony ILÇE-7R - what is the speed of read/write in the camera
I have several Sony ILÇE-7R cameras used for a given application where more than 80 panes in a row with 1 second interval occur.
When you are taking pictures on a 1 sec shutter time / 1.2 s, then the camera tends to slow when writing the buffer on the SD card. (A suitable high-speed sdcard has been used). When the buffer is disabled on the SD card, then the camera accepts no any command of the shutter (IR Led or cable gives the same question), so I'm missing components/images.
What is the read/write speed in the camera?
What are the compensation of buffer time?
Are there settings that can improve the buffer time on the SD card, while taking still pictures of compensation?
Is there firmware settings that have been implemented to improve the write speed camera?
Thank you very much
Kind regards
-
SSD on MPB early 2011 (13 inches) slow write speed
Hey all,.
I installed an SSD Crucial of MX300 in my MPB 2011 (13 inches). I get that I have probably will not hit the read/write 510/510, said the player, but right now I get only a writing speed of 240 vs a reading of 470.
Any ideas on why it's so slow?
Thank you.
What is it connected to internally? If we replace the optical drive, then it may be because it's a 3 Gb/s bus rather than the primary drive SATA 6 GB/s bus connects to.
Do you have your repartition and reformat the SSD drive before using it? It is not unusual to see some write speeds slower than reading speeds. The MX300 is a new economic model that may be slower than expected in real use.
-
Hello
I am writing a VI to control PWM with a microcontroller via a serial port. I wrote a simple code for the microcontroller that allows me to set the ratio of duty cycle on a scale of 0-65535. It works very well with Termite of Compuphase (RS-232 plug); The microcontroller invited me to an entry, expected that I would one, updates and expected another entry when I decided to send him. Now, I'm trying to get the same functionality on a LabVIEW vi but hit a snag.
When I tried to send my orders with a series read base and an example of writing, everything worked fine. I could see the prompt entry, write an entry and if I was quick enough, check out the update message. Even when I was not fast enough, I was able to check the update by monitoring the PWM pin with a Logic Analyzer. The problem with the basic example, however, is that I need to update the report to aura cyclical ratio, so I went for an example of reading continues writing. The problem I've met; is that I have to switch between reading and writing to make it work. When I do that, either I don't hold write it down long enough and nothing happens, or I get several updates when I switch to reading. Some of these updates don't even match and produce updates to defective upgrades for example; 16000 16000, 16000, 16000, 6000, 600, 60, 16000, 1600, 60, 0, 0, 0, 16000, 60, 0, 0 etc.
I tried which allows characters of endpoint in the hope that the writing would end at the end and go to reading where he would receive a termination character and wait for me allow writing once again, but nothing helped. I still have to alternate between the two and either get no response on reading several updates of variable accuracy. I tried to remove her allows read/write and their structures of matter in the hope that the loop flow, associated with the characters of endpoint would the case, but then the updates don't register at all. The funny thing is I did a VI like this before with an Arduino and that there not even no need to switch between writing and reading (I'm now using a Board of Freescale FRDM).
I was also the frequency of timeout errors; Error-1073807339 at VISA Read, reason Possible: VISA Hex 0xBFFF0015. I removed the option to stop the while loop if there is an error so I can run but always pops up an error on the judgment occasionally. Could the problem of synchronization always cause me problems?
Would appreciate all advice really, I am providing my slightly modified example screws and can provide the code for microcontroller on request, even if it's very simple.
Thanks in advance, it is
Yusif NurizadeIn other words, frankly, a good bad example you according to your code. Also, you have the order of writing and read upside down in your amendment if the instrument requires a command to return something. It should really be using a structure of the event. The structure of the event around a write and read and use a value change event. I have attached a quick change. This mod is still a reading after writing. If necessary, you may have two separate events to write and read.
-
a speed of read/write DAQ card mode change will reach 200K
HEY, man,
I have a project needs to test two points I name them point A and point B, the first time, I should point A 5V DC input, voltage inductive test point B, sencodly, give point B 5V DC input and inductive point test output voltage, this means and two analog ports must read and write sharing mode , and the test speed must be 100 KB, if I have a 200 KB data acquisition card, can the speed of read/write mode change reach 100 KB for an analog port? or, please give your suggest for my this kind of situation, thank you.
Hi API,.
I see that you are trying to measure voltages using a single channel at a time on a data acquisition card.
Unfortunately, you cannot change the inputs to the outputs or vice versa on a map of data acquisition, they are static.
What I recommend is either using a switch like this: http://sine.ni.com/nips/cds/view/p/lang/en/nid/207130 where you will need a high chassis.
Or, having four channels, 2 inputs and 2 outputs and try to measure it. You should have the necessary speed as well.
If you have any other questions, I'd be happy to answer.
Thank you very much
-
Several problems of reads/writes of Visa
Hi all.
I've been using labview VISA to communicate with an I/O device called a µChameleon.
I need to monitor the status of mutiple pins by sending an entry VISA to query the PIN then use a read VISA to identify the State of the PIN.
The problem I have is when I use several reads/writes VISA. When I run the present, only one VISA reading returns the corresponding pin State, but everything else show nothing. The funniest is when I use run highlight, they will return all the State of the PIN.
The photo below shows the basic principle of what im doing by simply copying the base serial number read and write code. For example, I send the string 'State of pin 1' followed by a carriage return and if it works correctly it should return a string Read VISA saying ' pin 1 1 "(top) or" pin 1 0 "(low)." ""
Can someone help me witht that. Is this a timing problem with the VISA of the readings?
-
any ideas? ~ macbook pro (13-inch mid 2009) speed problem & sound a1278 ~ el capitan 10.11.5 (15F34)
EtreCheck version: 2.9.12 (265)
Report generated 2016-06-25 16:47:10
Download EtreCheck from https://etrecheck.com
Time 02:21
Performance: Excellent
Click the [Support] links to help with non-Apple products.
Click [details] for more information on this line.
Verify the signatures of Apple: enabled
Problem: Computer is too slow
MacBook Pro (13-inch, mid 2009)
[Data sheet] - [User Guide] - [warranty & Service]
MacBook Pro - model: MacBookPro5, 5
1 CPU 2.53 GHz Intel Core 2 Duo: 2 strands
8 GB of RAM expandable - [Instructions]
BANK 0/DIMM0
OK 4 GB DDR3 1067 MHz
BANK 1/DIMM0
OK 4 GB DDR3 1067 MHz
Bluetooth: Old - transfer/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Battery: Health = Normal - Cycle count = 7
NVIDIA GeForce 9400M - VRAM: 256 MB
Color LCD 1280 x 800
OS X El Capitan 10.11.5 (15F34) - since startup time: less than an hour
SAMSUNG SSD 840 EVO 250 GB disk0: (250,06 GB) (Solid State - TRIM: No.)
EFI (disk0s1) < not mounted >: 210 MB
a /Volumes (disk0s2) / has: 50,00 (GB 49,84 free)
b (disk0s3) /: 199,07 go-go (160,81 free)
Recovery HD (disk0s4) < not mounted > [recovery]: 650 MB
HL-DT-ST DVD - RW GS23N)
Built-in ISight from Apple Inc..
Card reader Apple
Apple Inc. Apple keyboard / Trackpad
Computer, Inc. Apple IR receiver.
Apple Inc. BRCM2046 hub.
Apple Inc. Bluetooth USB host controller.
/ etc/sudoers, 1242 but file size expected 2299
Protection of the integrity of system status: disabled
Any where
/ System/Library/Extensions
[no charge] com.native - instruments.driver.NIUSBDeviceHelper (1.0.8 (R32) - 2016-06-25) [Support]
[loaded] 7 tasks Apple
[loading] 165 tasks Apple
[operation] 66 tasks Apple
[loaded] 47 tasks Apple
[loading] 164 tasks Apple
[operation] 79 tasks Apple
[loading] com.adobe.fpsaud.plist (2016-06-14) [Support]
[loading] com.malwarebytes.HelperTool.plist (2016-06-25) [Support]
com.apple.CSConfigDotMacCert [fail]-[...] @me.com - SharedServices.Agent.plist (2016-06-23) -/System/Library/Frameworks/CoreServices.framework/Frameworks/OSServices.framewo rk/Versions/A/support/CSConfigDotMacCert: Executable not found!
[loading] com.google.keystone.agent.plist (2016-06-23) [Support]
gfxCardStatus Application (~ / Downloads/gfxCardStatus.app)
Hidden Google Chrome application (/ Applications/Google Chrome.app)
NIHardwareAgent Application hidden (/ Library/Application Support/Native Instruments/Hardware/NIHardwareAgent.app)
[ongoing] com.Apple.XPC.launchd.oneshot.0x10000002.Google Chrome
[ongoing] com.eidac.smcFanControl2.54432
[ongoing] com.etresoft.EtreCheck.6112
com.google.Chrome.47072 [loading]
com.native-[ongoing] instruments.NIHardwareService.54752
[loading] 411 tasks Apple
[operation] 176 tasks Apple
FlashPlayer - 10.6: 22.0.0.192 - SDK 10.9 (2016-06-23) [Support]
QuickTime Plugin: 7.7.3 (2016-06-25)
Flash Player: 22.0.0.192 - SDK 10.9 (2016-06-23) [Support]
JavaAppletPlugin: 15.0.1 - 10.11 (2016-06-23) check the version of the SDK
Default browser: 601 - SDK 10.11 (2016-06-25)
Flash Player (2016-06-14) [Support]
Time Machine not configured!
28% by mail
11% WindowServer
6% kernel_task
2% hidd
1% fontd
Top of page process of memory: ⓘ
1.65 GB Google Chrome Helper (13)
563 MB kernel_task
Mdworker (19) 360 MB
221 MB Google Chrome
Com.apple.WebKit.WebContent (2) 131 MB
3.77 GB of free RAM
used 4.48 GB RAM (2,40 GB being cached)
Used Swap 0 B
25 June 2016, 16:18:23 self test - passed
24 June 2016, 18:55:37 ~/Library/Logs/DiagnosticReports/WebProcess_2016-06-24-185537_[redacted].crash
com.apple.WebProcess - /System/Library/PrivateFrameworks/WebKit2.framework/WebProcess.app/Contents/Mac OS/process Web
MacBook Pro, average vintage thrash?
Your hard drive may be faulty, run disk utility > first aid your recovery volume or another hard drive under OS X on it and let us know what he reports.
https://support.Apple.com/en-us/HT201639
Edit: you 2009 isn't a recovery, run it from your installation CD original or other dislk with OS X on it.
-
MacBook Pro SSD 7.1 more slow speed 200 MB
Hey,.
I bought an SSD of Sandisk and 480 GB (http://www.amazon.de/SanDisk-Plus-480GB-Interne-schwarz/dp/B018X8LB2G) with a speed of 480 MB/s reading and writing speed of 400 Mbps. I compared with Blackmagic Disk Speed Test and the result seems to be horrible. Speed of 250 MB/s read and 180 MB/s write speed.
The Macbook Pro 7.1 is not compatible with these speeds or I do something wrong? Would be happy for any response.
See you soon
Maybe you are looking for
-
Fastest way to an average of images (imaqdx)
Hello I'm looking for a faster way to images on average. I take each pixel value intensity, then divide by the number of images at the end and convert it back into an image. There are currently 3 s for medium 10 images which is not ideal for the real
-
Try to pay my subscription to Xbox live with another card, the payment option freezes.
Original title: freezing payment options I'm trying to pay my subscription to Xbox live with another card that the original one was cancelled. When I pay the screen goes to a standby screen and stays there forever. (with the small blue dots going rou
-
XP computers cannot locate Vista printer on LAN
I'm trying to set up a home network. I have 2 older computers running SP3 of XP and a Vista Premium 32. The Vista computer will not locate the other 2, and other computers will locate the Vista computer, but cannot access the printer on it. I have
-
Why used my computer let me download yahoo Messenger it repeat myself the firewall blocks?
Why used my computer let me download yahoo Messenger it repeat myself the firewall blocks?
-
BlackBerry smartphones add to main Menu
How can I add a button to the main menu for an app I have installed. Won't click applications, then the app