stacking n3048

Similar Questions

• Add new N3048 to current stack of switch

  Hello

  I have a new N3048 switch to add to our current stack of 2 N3048 to provide more capacity. Before lighting for the first time, that I would like to know if I need to run through the initial configuration or can I just connect the new battery switch and power, it will then get the config of the switch?

  The firmware must also update on the battery, can I do this first or when all 3 switches are in the stack?

  Thank you very much.

  Since the existing battery and the new, we can have different firmware revisions, generally the best route is updating the firmware on the existing stack, and then on the new switch to add before attaching it to the battery. You should not need to do any initial configuration before attaching. As always recommended is to use a ring topology when stacking to avoid "split brain" IP address and duplicate problems are common with chain failures.

  B

• Chest N3048 stack N2048 stack

  I have 2 N3048 my heart for virtualization switches and 3 N2048 switches stacked to computer/phones.   I need to connect the two heaps, I have 4 cat6 cables, connecting so

  N3048 1/0 / 47-> N2048 1/0/47

  N3048 1/0 / 48-> N2048 1/0/48

  N3048 2/0 / 47-> N2048 2/0/48

  N3048 2/0 / 48-> N2048 3/0/48

  VLANs that need to communicate are VLAN 2, 5, 11, 23

  Computers are VLAN 2 (10.10.2.0/24)

  Serviers is VLAN 11 (10.10.1.0/24)

  The development is 23 VLAN (10.10.8.0/24)

  MGMT is VLAN 5 (10.10.5.0/24)

  Each of these VLANs have an assigned IP address on each switch interface.

  My question is:

  4 ports used to kill her?

  If it was a SHIFT / port channel?

  And how the hell set.  Currently, here is my config

  Kernel stack:

  interface item in gi1/0/47
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk
  output
  !
  interface item in gi1/0/48
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk

  interface Gi2/0/47
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk
  output
  !
  interface Gi2/0/48
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk
  output
  !
  interface port-channel 1
  Description 'link - Stack1.
  switchport mode general
  pvid switchport General 11
  VLAN allowed switchport General add 2,5,11,23
  output

  User Stack1

  interface item in gi1/0/47
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface item in gi1/0/48
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface Gi2/0/48
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface IG3/0/48
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface port-channel 2
  Description "link - TPL-Core."
  switchport mode general
  pvid switchport General 11
  VLAN allowed switchport General add 2,5,11,23
  output

  I can only ping the 10.10.1.0 interfacing switches... so I know I've got completely wrong thi... Thanks for the help!

  The amount of bandwidth for a network will vary from network to network. If you have connections to available ports 4 is perfectly fine. You can always expand or cut connections later.

  The stack will act as a logical device, so there is a LAG/portchannel. User guide page 945.  http://Dell.to/1H4xyD5

  When it comes to routing between VLANs. Usually only the main switch will have an IP address for all the VLANS. The other switches will have 1 IP address for management. Your clients will have an IP address for the subnet of the VLAN they are. And have the gateway on the IP address that is assigned to the VLAN on the switch that is configured for routing.

  For the port settings try this out.

  interface port-channel 1

  Description 'link - Stack1.

  switchport mode general

  pvid switchport General 11

  switchport general allowed vlan add 2,5,23 tag

  VLAN allowed switchport General add 11 untagged

  switchport vlan allowed General remove 1

  interface port-channel 2

  Description "link - TPL-Core."

  switchport mode general

  pvid switchport General 11

  switchport general allowed vlan add 2,5,23 tag

  VLAN allowed switchport General add 11 untagged

  switchport general allowed remove vlan 1

  Then for connectivity try Ping between customers and not pass interfaces.

  Keep us informed.

• Best wiring for blade M8024-k switch stack to ToR N3048 using 10GBe modules?

  

  I have a M1000e with 2 x M8024-k toggle (bunk) in B1 and B2 slots, I connected the switches rack via ports of 10GbE for the 2 x N3048 (bunk)

  What is the best way to connect?  And how do I add or number connections LAG as none of them are attached to the same switch?

  Thank you very much

  Battery

  Hello

  It is a good way to connect the two piles that you can configure the link as an aggregate of 4 X 10 giga links. You should use LACP rather than static, so that any broken link is quickly identified and thus will be abandoned in the aggregate.

• N3048 vlan trunk band guaranteed bandwidth

  Hello

  Ive got 2 batteries of n3048 which will be connected by a link of fiber shds 1 Gbps, there are several local networks virtual on each stack and some of them I want trunk on the binding fiber.

  an of vlan is for a balanced load diversely routed internet connection, there is a router on each site with 100 Mbps bandwidth, but also firewalls at each site that will be in the same vlan.

  I don't want no internet to run slow because something is hogging the bandwidth on the shds, so the question is how can I guarantee 100 Mbps of traffic for vlan 10 through the shds with us other traffic crossing of vlan?

  I have install other powerconnect switches and switches cisco with trunking VLANs between switches but I've ever done where I need to ensure a slice of bandwidth with QOS?

  I'd appreciate any help or advice to achieve this

  Thank you very much

  Hi Daniel,.

  Sorry for the late reply its been a bit choppy on other projects so just had time to test this out.

  Here's what I ended up using in the config:

  Console (config) # class - match-all card VLAN_10_MATCH
  Console (config-WCPA) # match vlan 10

  Console (config) # VLAN_10_MARK policy-map on
  class console(config-Policy-classmap) # VLAN_10_MATCH
  Console(config-Policy-classmap) # brand cos 5

  Console (config) # int item in gi1/0/48
  Console (Config-if-X/Y/Z) # classofservice trust dot1p
  Console (Config-if-X/Y/Z) # classofservice dot1p-mapping 5 3
  Console (Config-if-X/Y/Z) # cos - min - bandwidth tail 0 0 10 0 0 0 0
  Console (Config-if-X/Y/Z) # cos - queue strict
  Console (Config-if-X/Y/Z) # - political service on VLAN_10_MARK

  I applied the same configuration for the trunk on two piles of switch port
  

  Thanks for your help in pointing me in the right direction

  I used jperf on 2 laptops in VLAN 10, 1 in each switch then your laptop on the other switch into a vlan with jperf mode server and 3 computers, send traffic using jperf him around the trunk and which seems to work well. ive tried run qos traffic vlan first and then maxing the bandwidth through the traffic trunk vlan qos not and then vice versa with traffic vlan qos to a already maxxed bandwidth through the trunk and he still gave him its bandwidth of 100 Mbps in both scenarios.

   

  concerning
  

• VLAN N3048-PC6224

  Hello world

  I'm trying to configure a valn between 2 switch (real-time 4 switches but stacking 2 / 2)

  My config is quite simple:

  N3048:

  ethernet interface 2 / g26-> first computer
  switchport access vlan 2
  output

  interface tengigatethernet 2/0 / 2-> optical fiber
  switchport access vlan 2
  output

  PC6224

  ethernet interface 2 / g26-> second computer
  switchport access vlan 2
  output

  ethernet interface 2 / g47-> optical fiber
  switchport access vlan 2
  output

  I use a transcevier SFP 1000BASE-SX 850nm wave 550 m, even on the 2 switches.

  The fiber link is in place on the device but no work from rose.

  Need help!

  Thx for the answers of the future

  Hello

  I have add this command:

  Console #configurer

  Console (config) #interface Tengigabitethernet 2/0/2

  access mode console (config-if-Te2/0/2) #switchport

  Console (config-if-Te2/0/2) #switchport access vlan 3

  Console (config-if-Te2/0/2) #exit

  Console (config) #exit

  #show running-config Tengigabitethernet 2/0/2 console interface

  switchport access vlan 3

  Console #.

  Why when a glance running, 0/Te2/2 interface configuration does not accept "switchport mode access"?

  I will configure the other switch and try to ping everyone together

  EDIT:

  Ping does not work.

• I can rearrange the email component and seen to be side by side rather than stacked?

  I can rearrange the email component and seen to be side by side rather than stacked?

  What does that mean?

• We can handle groups of tabs in the tab tool bar, dragging and stacking style tabs Opera 12?

  The groups are an interesting alternative to the tab stacking Opera12 (manage a sort of Group of Opera from the toolbar of the tab drag / combined). It might be useful to combine the two, in keeping the Group window, but to also grouping and movement to the toolbar of the main tab. I was hoping to find a complement to this (?) but no luck so far.

  It is listed as a feature description for Tab Utilities #21.

  • https://addons.Mozilla.org/firefox/addon/tab-utilities/

  This feature was proposed 3 (bug 642100) years ago, but no developers have shown no interest so far.

  • https://wiki.Mozilla.org/Firefox/projects/TabCandy/design/MiniGroups

• User profile of Stack overflow is not displayed correctly

  User Stack overflow profile page is displayed wrongly, hides an empty space at the top of the page and some info.

  I see what you mean. It seems that the dropdown that says 'Summary' push this content to the large block to the right (sometimes you can see a small piece of it on the right edge of the page). This problem does not occur in the (2.3.4) stock Android browser.

  If I use a Fennec useragent string in the User Agent Switcher extension, I can reproduce the problem on a desktop browser (13 Firefox beta 4). The drop down menu is floated in a container that uses 100% of the width of the screen. The next element floats upward alongside < select > rather than fall under this one, because this next item is not a specified width or the minimum width.

  StackOverflow can solve this problem by changing the CSS to include a rule of compensation:

  
  .inner-wrap {
   	padding: 5px;
  	overflow: auto;
  	clear: left;
  }
  

  However, as end users, I don't know if there is something we can do.

  This problem appeared in the sites for years, and it seems unlikely that Firefox will change the way it handles the floats to work around developers who forget to erase. (Guess as to what the developer must have wanted was something that IE is long, but I think even Microsoft starting to require developers to pay more attention).

• HP50g: HP50g - hot to check if the object of the stack is a number?

  How to check if an object on the stack is a number or another type of data? There seems to be no any function to check on 50g.

  50 g advanced users to see, page 1-13:

  "The order TYPE ([left SHIFT] PRG-> TEST-> NXT-> TYPE) accepts any object as argument and returns the number that identifies the type of this object." For example, 'HELLO' TYPE returns 2, the value of a string object. See table of object types in Chapter 3, in the command TYPE, to find objects of calculator and corresponding type numbers.

  Generally want to DUP the object to the level of the stack 1 first of all, because likely you want to do something with it, after checking his type.  The following RPL program checks the type of the object in level 1 of the pile and adds a string to the stack indicating its type.  Only some of the possible types are checked and a generic "something else" translates to others:

  «
  
    TYPE OF DUP
  
    CASE
  
      DUP 0 == THEN DROP 'real number' END
  
      DUP 1 == THEN DROP "complex number" END
  
      DUP 2 == THEN DROP 'chain' END
  
      DUP 3 == THEN DROP "real array" END
  
      DUP 5 is THEN DROP 'list' END
  
      DROP "something else"
  
    END
  
  »

• How to make a stacked cluster chart?

  I am creating a cluster diagram, classified by different emails sent to customers (let's call them 1, 2 and 3 Email) and has each kind of stacked e-mail based on the answer (opened, clicked).  Is it possible to have your chart be grouped and stacked?  The x-axis are labeled by the day of the week, and I would be more group by email (1, 2 and 3) every day.

  Thanks in advance for the help!

  Numbers isn't a stacked column cluster chart. But you can use a 3D stacked column and can 'cheat'similar to the way you would in Excel.

  

  The trick is to leave blank lines in the table of data which, when the fill color is removed, the differences between the clusters form.

  I don't understand how to get the labels for each cluster in the right place.  When the two left columns are defined as cluster labels column headers appear where it is indicated in the screenshot, is not ideal.  It is possible that the days of the week may have to be manually labeled with text boxes.

  SG

• Problem to download Bluetooth stack file - file is corrupt

  Hello

  I am trying to download the driver for Win7 bluetooth stack (installed on A300-1 MB)
  The file available for download is corrupt.

  Is this only a problem for me?

  Thanks a bunch for the help ():
  return on investment.

  Hello

  Please, check

  http://Support1.toshiba-tro.de/tools/Bluetooth/BT-stack.zip?submit=download for Windows 7 32 bit

  http://Support1.toshiba-tro.de/tools/Bluetooth/64-bit/BT-stack-64bit.zip?submit=download for Windows 7 64-bit

• Satellite P750: Impossible to install the Bluetooth Stack on Windows 7 (x 64) driver

  Hello.

  I own a * Satellite P750-02 t * (part No. * PSAY3A - T 02 001 *).

  In the order I did:

  (1) I formatted the HARD drive and reinstalled the operating system of * Windows 7 x 64 Ultimate SP1 *.

  Then I downloaded * ONLY the BIOS and drivers * of [his downloads page | http://www.mytoshiba.com.au/support/computers/satellite/p750/psay3a-02t001/download?os=25]:

  (2) I've updated the BIOS for * v1.90* (the laptop came with v1.80)

  (3) I have installed all drivers:
  -LAN and WiFi
  -Chipset Intel latest (available)
  -all video drivers (NVIDIA Graphics, Intel HD Graphics and Intel HDMI)
  -Card reader
  -Realtek HD Audio (later)
  -Synaptics Touchpad
  -USB3.0
  -IR
  TV tuner
  However, I * cannot install Bluetooth driver (v8.00.06 (T) *)...

  When I run the installation program of the [aforementioned page | http://www.mytoshiba.com.au/support/computers/satellite/p750/psay3a-02t001/download?os=25] it detects partially *'Bluetooth USB Controller-10 TOSHIBA'* (USB\VID_0930 & PID_0215 & REV_001)
  and then the installation freezes simply displaying + "install the Bluetooth driver. Please wait +.' and stay like that forever...

  I also tried to download a driver [another location | http://aps2.toshiba-tro.de/bluetooth/index.php?page=download-toshiba] for laptops TOSHIBA - v8.00.02 (T):
  and followed installation instructions displayed under "Details".
  but he had the same result: the installer simply crashes...

  Install fix (* KB978258 *) recommended it did not work either - the message "+ update is not applicable to your computer +" appears.
  And I understand why - this fix is [already included: http://download.microsoft.com/download/E/B/A/EBA55FE2-373A-4351-9346-6D762B79AA69/Updates%20in%20Win7%20and%20WS08R2%20SP1.xls] in Service Pack 1 for MS Windows 7.

  I spent hours searching the Internet for a solution. Although there are some similar cases, none of the recommendations actually worked. I tried to install:
  -WiFi driver before installing the Bluetooth (someone suggested that these two are parts of the same card);
  -Repeat Mode Setup without failure;
  -* Toshiba value added package * hoping that somehow these tools will kick in.
  Nothing has worked...

  It is interesting to note that when, in the interests of experimentation, I tried to run installation for my generic Bluetooth adapter (using the driver [for non-TOSHIBA notebooks | http://aps2.toshiba-tro.de/bluetooth/index.php?page=download]) then everything runs smoothly!

  * Using connection Bluetooth on this laptop is absolutely crucial for TI
  I hope that I won't get back this beautiful laptop as I know that TOSHIBA is one of the best manufacturers and I am sure, that there is a solution to this problem.

  Thank you very much.
  Evgeny.

  Post edited by: cardiovascular disease
  specified on the use of another generic Bluetooth adapter with non-TOSHIBA driver

  You can use the key combination FN + F8 to toggle WLAN?
  You can also see BT symbol there?

  Before you begin installation battery BT try to activate BT module by using the FN + F8 key combination.

  Generally avoid some problem with it. Toshiba BT stack is tested on al models proposed by Toshiba and fireplace installation BT has, in my view, nothing to see what version of Win7 you use.

  Do not return this laptop. It has to do is just install drivers, tools and utilities. Please note: BT stack is included in the recovery image so BT must work.

  Also, I must say that OS installation of drivers, tools and utilities on Toshiba laptop must / should be installed in the correct order. Many tools can work only and must be installed on basic stuff that can be installed with other specific tools of Toshiba.

  Please send a few comments if this FN + F8 will work.

• Audio stream OF Android to win 10 PC + Toshiba BT Stack

  First of all, I don't mean ways to listen to music from the PC to the tablet.

  I am looking for a way to play music, e-books, etc. that I have on my Tablet and hear it through the speakers connected to my PC.

  I'm used to be able to do this with a laptop running Windows 7 HP.

  In a previous life, a Windows XP box, I used the Toshiba Bluetooth Stack, so I thought I could give it a try. I downloaded a file, TC00636200A, which, after installation, tells me it's "Bluetooth Stack for Windows by Toshiba, Version v. 9.10.32 (T). I had to re-pair of my keyboard, mouse and tablet, and I can transfer files from the PC to the table and the tablet to the PC. If the basics seem to work.

  But how do the audio of the tablet to the PC and the speakers? I see a checkbox for 'Service to flow' Audio in the Panel settings of Toshiba BT and that looks promising, but when I hoover the mouse over it I get a message about how this allows the audio synchronization of the remote device service and something about a microphone? Hardly what I'm looking for.

  Someone at - it runing Windows 10 (Pro?) with the Toshiba BT Stack and is able to stream music from a phone or tablet to the PC?

  No answer seems to be coming. Guess I'll go ahead and uninstall the Toshiba stack. Good bye.

• Satellite U940 - BT does not work after update from BT Stack

  Hello

  The bluetooth in my U940 Satellite with Windows 8, 1-update stopped working properly after I updated the Bluetooth Stack version: v9.10.32T because one of the programs pre-installed Toshiba told me to do.

  The option of connection / disconnection of Bluetooth in windows discovers tiles disappeared. There is no information on the bluetooth it more.

  Bluetooth seems to be installed and when I try to pair a bluetooth Toshiba bluetooth speaker Manager opens (until I could only connect the windows bluetooth devices). The connection with the speaker sometimes is done properly, but after you connect and reconnect the audio speaker is not passed over.

  I tried to reinstall the battery Bluetooth and then trying with an older version, but nothing works.
  Also, I tried to reinstall the filter of Bluetooth driver Package (bfdp - 20131011123106.zip), but the installation does not start when the files are extracted.

  Can someone help me to fix it?
  Thank you

  PS: The laptop is still under warranty, could it be refunded?

  Very quick and good solution.
  The key is that you can use BT again.
  Thanks for the comments.