VLAN N3048-PC6224

Similar Questions

• N3048 vlan trunk band guaranteed bandwidth

  Hello

  Ive got 2 batteries of n3048 which will be connected by a link of fiber shds 1 Gbps, there are several local networks virtual on each stack and some of them I want trunk on the binding fiber.

  an of vlan is for a balanced load diversely routed internet connection, there is a router on each site with 100 Mbps bandwidth, but also firewalls at each site that will be in the same vlan.

  I don't want no internet to run slow because something is hogging the bandwidth on the shds, so the question is how can I guarantee 100 Mbps of traffic for vlan 10 through the shds with us other traffic crossing of vlan?

  I have install other powerconnect switches and switches cisco with trunking VLANs between switches but I've ever done where I need to ensure a slice of bandwidth with QOS?

  I'd appreciate any help or advice to achieve this

  Thank you very much

  Hi Daniel,.

  Sorry for the late reply its been a bit choppy on other projects so just had time to test this out.

  Here's what I ended up using in the config:

  Console (config) # class - match-all card VLAN_10_MATCH
  Console (config-WCPA) # match vlan 10

  Console (config) # VLAN_10_MARK policy-map on
  class console(config-Policy-classmap) # VLAN_10_MATCH
  Console(config-Policy-classmap) # brand cos 5

  Console (config) # int item in gi1/0/48
  Console (Config-if-X/Y/Z) # classofservice trust dot1p
  Console (Config-if-X/Y/Z) # classofservice dot1p-mapping 5 3
  Console (Config-if-X/Y/Z) # cos - min - bandwidth tail 0 0 10 0 0 0 0
  Console (Config-if-X/Y/Z) # cos - queue strict
  Console (Config-if-X/Y/Z) # - political service on VLAN_10_MARK

  I applied the same configuration for the trunk on two piles of switch port
  

  Thanks for your help in pointing me in the right direction

  I used jperf on 2 laptops in VLAN 10, 1 in each switch then your laptop on the other switch into a vlan with jperf mode server and 3 computers, send traffic using jperf him around the trunk and which seems to work well. ive tried run qos traffic vlan first and then maxing the bandwidth through the traffic trunk vlan qos not and then vice versa with traffic vlan qos to a already maxxed bandwidth through the trunk and he still gave him its bandwidth of 100 Mbps in both scenarios.

   

  concerning
  

• N3048 tagging VLAN

  Just recently, we bought a n3048 to replace our PowerConnect 6248 failure. The section belonging to a VLAN on the 6248 allows to tag the ports for VLAN specific in four States. An empty box for unconfigured, U for unidentified, T for the tag and F I believe is forbidden. The n3048 has only two States: white and U. Can someone explain how to have a law on the port in the same way it would on the 6248 has been T tag?

  You need to set the port in general or Trunk mode settings in order to Tag VLAN. Page 663 user guide begins detailing options and how they are defined.

  http://Dell.to/1wlbEn2

  See you soon

• PC6224 Configuration of VLAN

  Hello

  I am desirous of VLAN my iSCSI data in two separate VLANS and think I understand what to do. I would like to just anyone for the validation test it before I go live and eventually get things horribly wrong.

  

  All i15 labeled ports must be configured as switchport access vlan 15
  All i16 labeled ports must be configured as switchport access vlan 16
  Four XG ports must be configured as vlan allowed switchport General add 15.16 tag.

  So far I think I have it but I'm not sure on how to get the traffic untagged crossing ports XG.
  It will do it automatically, or should I set switchport General pvid 1 for these ports, so all untagged traffic goes to the network vlan by default?

  I need to set the VLAN on LAG3 or will it not serious because the ports are marked? Or do I not have to label the ports if the OFFSET is the tag? Or I have to mark the two?

  Thanks for the help,

  Jim.

  Put a PVID on a LAG sets going what traffic VLAN not identified.

• pc6224 VLAN & routing

  Dear everybody

  I have a default vlan1 with the management interface and a port base vlan2 with "switchport mode access", gave vlan2 one IP address, and then "ip Routing" routing according to the docs.

  I must be missing something because I can't always ping as vlan2.

  Please advise, thank you very much.

  You can see the use of the ACL. Here are a few documents with information about the use of the ACL.

  http://Dell.to/1AACg9V

  http://Dell.to/1Ibp6yr

  http://Dell.to/1IhR169

  Page 111:

  http://Dell.to/1OQBo4S

  See you soon

• Chest N3048 stack N2048 stack

  I have 2 N3048 my heart for virtualization switches and 3 N2048 switches stacked to computer/phones.   I need to connect the two heaps, I have 4 cat6 cables, connecting so

  N3048 1/0 / 47-> N2048 1/0/47

  N3048 1/0 / 48-> N2048 1/0/48

  N3048 2/0 / 47-> N2048 2/0/48

  N3048 2/0 / 48-> N2048 3/0/48

  VLANs that need to communicate are VLAN 2, 5, 11, 23

  Computers are VLAN 2 (10.10.2.0/24)

  Serviers is VLAN 11 (10.10.1.0/24)

  The development is 23 VLAN (10.10.8.0/24)

  MGMT is VLAN 5 (10.10.5.0/24)

  Each of these VLANs have an assigned IP address on each switch interface.

  My question is:

  4 ports used to kill her?

  If it was a SHIFT / port channel?

  And how the hell set.  Currently, here is my config

  Kernel stack:

  interface item in gi1/0/47
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk
  output
  !
  interface item in gi1/0/48
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk

  interface Gi2/0/47
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk
  output
  !
  interface Gi2/0/48
  active in mode channel-group 1
  spanning tree portfast
  switchport mode trunk
  output
  !
  interface port-channel 1
  Description 'link - Stack1.
  switchport mode general
  pvid switchport General 11
  VLAN allowed switchport General add 2,5,11,23
  output

  User Stack1

  interface item in gi1/0/47
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface item in gi1/0/48
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface Gi2/0/48
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface IG3/0/48
  active in mode channel-group 2
  switchport mode trunk
  output
  !
  interface port-channel 2
  Description "link - TPL-Core."
  switchport mode general
  pvid switchport General 11
  VLAN allowed switchport General add 2,5,11,23
  output

  I can only ping the 10.10.1.0 interfacing switches... so I know I've got completely wrong thi... Thanks for the help!

  The amount of bandwidth for a network will vary from network to network. If you have connections to available ports 4 is perfectly fine. You can always expand or cut connections later.

  The stack will act as a logical device, so there is a LAG/portchannel. User guide page 945.  http://Dell.to/1H4xyD5

  When it comes to routing between VLANs. Usually only the main switch will have an IP address for all the VLANS. The other switches will have 1 IP address for management. Your clients will have an IP address for the subnet of the VLAN they are. And have the gateway on the IP address that is assigned to the VLAN on the switch that is configured for routing.

  For the port settings try this out.

  interface port-channel 1

  Description 'link - Stack1.

  switchport mode general

  pvid switchport General 11

  switchport general allowed vlan add 2,5,23 tag

  VLAN allowed switchport General add 11 untagged

  switchport vlan allowed General remove 1

  interface port-channel 2

  Description "link - TPL-Core."

  switchport mode general

  pvid switchport General 11

  switchport general allowed vlan add 2,5,23 tag

  VLAN allowed switchport General add 11 untagged

  switchport general allowed remove vlan 1

  Then for connectivity try Ping between customers and not pass interfaces.

  Keep us informed.

• Battery M8024-k (pair) M3048 (pair) battery gal, VLAN and port groups?

  Hi all

  I'm getting more confused by the minute.  I have a pair of M8024-k blade switches in a M1000e enclosure, outside, I have a pair of N3048 switches.

  I think I have the job of stacking on the M8024-k, but I found a configuration guide for Simple mode that says take port 17-20 outside the Group of ports on the pair aggregation and leave the stack ports and internally in the PA Group.  When I do that they remain outside the group, if I do it in the CLI or the GUI.

  Does anyone have a configuration guide that shows how I can pair trunk the 2 together and allow 4 VLAN that I keep coming without access to blade servers inside?  What I get out of simple mode on the M8024-k to achieve?

  Any help gratefully received.

  

  The best source of information is going to be the user guides.

  www.Dell.com/.../manuals

  www.Dell.com/.../manuals

  I would wear the 8024-k off simple mode.

  Console# not simple mode

  On two batteries, you will need to aggregate 4 ports together.  Here is an example to place a port in an aggregation group.

  Console (config) # interface gigabitethernet 0/1/5

  Console (Config-if-1/0/5) # channel-group mode 1 (active / Auto)

  Once the ports are in a channel-group 1, we can then configure the channel group to perform for several VLANs.

  Console (config) # interface port-channel 1

  trunk mode console (config-if-po1) #switchport

  #switchport console (config-if-po1) trunk allowed vlan add 2-150

  This is done, you should have connectivity.

  Keep us informed.

• Help with the VLAN routing

  I'm pretty green when I just went and routing configurations please bear with me.  I'm available what I want to achieve and what I could do until now (although it may be completely wrong).

  I have an office where we run low on IP addresses for our local network, the obvious answer is to get VOIP phones on their own subnet.  So, I have a switch PC6224 I want to use to create the second subnet.

  Existing Workstation LAN = 172.22.144.0 (255.255.255.0)

  Default GW for the LAN = 172.22.144.1 for all devices on that subnet

  I would like to create an IPPhone = 172.22.145.0 (255.255.255.0) subnet

  Here's what I have "Achieved" so far:

  Currently, I can ping from a client on 172.22.145.x to the 172.22.144.12 (VLAN 3 ip interface) but cannot ping any other 172.22.144.x that is not directly connected to the 6224 switch device.  Trying to ping the network 172.22.145.x device leave a device plugged into the 172.22.144.x VLAN on the switch of packets results was sent to the default gateway for the network (172.22.144.1) who does not know what to do with them.

  Here is my config of 6224 switch operation:

  Console execution #show
  ! Current configuration:
  ! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.
  ! 3.3.6.4 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 2-3
  VLAN 2 1 routing
  VLAN 3 2 routing
  subnet of VLAN association 172.22.144.0 255.255.255.0 3
  subnet of VLAN association 172.22.145.0 255.255.255.0 2
  output
  battery
  1 1 member
  output
  IP address no
  IP routing
  IP route 0.0.0.0 0.0.0.0 172.22.144.1
  interface vlan 2
  name "IPPhone.
  Routing
  IP 172.22.145.1 255.255.255.0
  output
  interface vlan 3
  name "TWLAN".
  Routing
  IP 172.22.144.12 255.255.255.0
  output
  level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15
  !
  interface ethernet 1/g3
  switchport access vlan 3
  output
  !
  interface ethernet 1/g4
  switchport access vlan 3
  output
  !
  interface ethernet 1/g5
  switchport access vlan 2
  output

  !
  interface ethernet 1/g6
  switchport access vlan 2
  output
  !
  interface ethernet 1/g7
  switchport access vlan 2
  output
  !
  interface ethernet 1/g8
  switchport access vlan 2
  output
  !
  interface ethernet 1/g9
  switchport access vlan 2
  output
  !
  interface ethernet 1/g10
  switchport access vlan 2
  output
  !

  interface ethernet 1/g11
  switchport access vlan 2
  output
  !
  interface ethernet 1/g12
  switchport access vlan 2
  output
  !
  interface ethernet 1/g13
  switchport access vlan 2
  output
  !
  interface ethernet 1/g14
  switchport access vlan 2
  output
  !
  interface ethernet 1/g15
  switchport access vlan 2
  output
  !
  interface ethernet 1/g16

  switchport access vlan 2
  output
  !
  interface ethernet 1/g17
  switchport access vlan 2
  output
  !
  interface ethernet 1/g18
  switchport access vlan 2
  output
  !
  interface ethernet 1/g19
  switchport access vlan 2
  output
  !
  interface ethernet 1/g20
  switchport access vlan 2
  output
  !
  interface ethernet 1/g21
  switchport access vlan 2

  output
  !
  interface ethernet 1/g22
  switchport access vlan 2
  output
  !
  interface ethernet 1/g23
  switchport access vlan 2
  output
  !
  interface ethernet 1/g24
  switchport access vlan 2
  output
  output

  Console #.

  Any help would be greatly appreciated.

  Thanks, Grant

  What port connects to 172.22.144.1 the jump according to the internet?

  What should happen is we need a VLAN 'remote' separate just for the connection between the 6224 and your 172.22.144.1 jump following the internet device.

  If 172.22.144.1 remains the same, then you must create another local network VIRTUAL to "TWLAN".  Eventually, VLAN 4 with a range of ip addresses of 172.22.146.1 - 254 255.255.255.0.  Where the VLAN 4 interface has an IP address defined as 172.22.146.1.  Once that all connected devices again VLAN 4 that were in the VLAN 3 need to change there IPs and gateway 172.22.146.1

  So the only port that has configuration of VLAN 3 is the connection to 172.22.144.1 port next to the internet break.  The IP address defined on the interface VLAN 3 should be in the same subnet as 172.22.144.1 range.

  Here is a diagram that can help you to see the whole upward.  VLAN 100 in the diagram represent VLAN 3 in your case.  Switch 2 would represent your device from the internet of next hop.

  

• PowerConnect 6224 VLAN Routing, unable to connect out of VLAN but able to connect by entering.

  To set up a new VIRTUAL local network to separate the common workstation network and obtain new DHCP scope, I had a few questions and found advice in the post of http://en.community.dell.com/support-forums/network-switches/f/866/t/19370806.aspx?PageIndex=3 but now I find that my traffic is not going through properly so I'm starting a new thread to get help shows all of working.

  Current primary network 192.168.1.0/24 (192.168.1.200 DHCP server). Adding new perspectives to the server for 192.168.3.0/24 active.

  Gateway default 192.168.1.0/24 is 192.168.1.254 (Cisco ASA, it was set up like that when I arrived and no room to insert the dedicated router). Adding route to 192.168.3.0/24 > 192.168.1.253 (PC6224 and VLAN 1 management interface). I also added exceptions NAT asa for the 192.168.3.0 network.

  I was still having some problems of scathing to the 192.168.3.0 network from the DHCP server and I added a static route on the server for this network, bypassing the ASA for routing to the switch.

  From the DHCP server, I am able to ping 192.168.1.253, 192.168.3.254 but not a laptop that runs Windows XP configured with 192.168.3.1 address connected to port 22 of the 6224.

  The XP laptop, I am able to ping 192.168.3.254 but not 192.168.1.253 or any other address in the 192.168.1.0 network.

  The switch CLI, I am able to ping on both networks destinations.

  Here is my config of switch. I have it set to scrape factory reset so there is no buried old ACL inside.

  console #show run
  ! Current configuration:
  ! Description of the system «PowerConnect 6224P, 3.3.5.5, VxWorks 6.5»
  ! 3.3.5.5 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 2
  VLAN 2 1 routing
  output

  IP 192.168.1.253 255.255.255.0
  by default-gateway IP 192.168.1.254
  IP - domain.local domain name
  name-server IP 192.168.1.11
  name-server IP 192.168.1.200
  IP routing
  IP helper-address 192.168.1.200 dhcp

  interface vlan 2
  name 'common '.
  Routing
  192.168.3.254 IP address 255.255.255.0
  IP netdirbcast
  bandwidth 10000
  business assistance-address IP 192.168.1.11
  field of IP helper-address 192.168.1.200
  IP helper-address 192.168.1.200 dhcp
  IP mtu 1500
  output

  l2relay DHCP
  DHCP l2relay vlan 2
  !
  interface ethernet 1/g21
  switchport access vlan 2
  output
  !
  interface ethernet 1/g22
  switchport access vlan 2
  output
  !
  interface ethernet 1/g23
  switchport access vlan 2
  output
  !
  interface ethernet 1/g24
  switchport access vlan 2
  output

  
  

• VLAN in point to point T1

  OK, here is what I am wanting to try:

  PC6248 > Cisco 2800 <---T1--->router Cisco 2800 router > PC6224

  I have 4 VLANS which would go through this link: 8 100 102 and 103. And that's how I think I will need to configure the VLAN:

  6248:

  switchport mode trunk

  switchport trunk allowed vlan add 8

  switchport trunk allowed vlan add 100

  switchport trunk allowed vlan add 102

  switchport trunk allowed vlan add 103

  2800:

  interface FastEthernet0/1.1

  encapsulation dot1q 8

  IP 192.168.8.10 255.255.254.0

  interface FastEthernet0/1.2

  encapsulation dot1q 100

  IP of 192.168.100.10 255.255.255.0

  interface FastEthernet0/1.3

  encapsulation dot1q 102

  IP 192.168.102.10 255.255.255.0

  interface FastEthernet0/1.4

  encapsulation dot1q 103

  IP 192.168.103.10 255.255.255.0

  OK, so I think I will need to add these two ends. Would this work?

  Thank you

  Travis

  
  

• App 5.1 server does not not on different VLANS

  Helloooo

  I just installed a new server and I use the server application. Everything seemed to work fine until I moved my iMac to a VLAN different. Profiles and update settings do not push to the iMac and sit at a stadium in waiting. Also to register the new iMacs on the server I get to the login server window and it crashes it and does not authenticate. Screen opens by saying that I can open a second window and registration. When I try to register, I get an unknown error and that it fails. It seems timeless. I tried to change a lot of settings prescribed by other users, but nothing helped. Someone at - it advice on what could be the problem.

  See you soon

  Sean

  Hello

  I took the easy on this way and bring a USB ethernet to my mac so that I have two physical interfaces. An in each VLAN.

  There are other ways to do this, and this is a good article:

  https://blog.Pivotal.IO/Labs/Labs/using-deploystudio-across-Subnets-a-Path-Not-t Aken

  Kind regards

  Erik

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• 2910al - 48G Switch: problem with the VLAN

  Hi all,

  I write a new message because I don't know what is happening on my SW series 2910al - 48G and v1910 - 48G.

  I put on the main core SW VLAN 610 and I put to this VLAN IP addreess 100.110.10.1 24-bit etc and it worked fine until yesterday. I change only PLEASE and I enebale STP - loop protect for ports in the range 1-52. (now I rolback this settings as was before)

  

  STP configuration

  

  Now, every PC that has for a long time what IP range 100.110.10.1 24-bit works fine, but new PC have problem with to get the new IP address. I tested it add a static and same address does not work.

  Introduced in second v1910 SW - 48 G VLAN as below

  I connect this flexible switch this \port SW 2910 - G 48, 46 (Vlan 610 tag) <>- at v1910-48G\ port 50 SW (Vlan 610 tahgged) other ports on this switch I put not marked.

  Configuration file for sw v1910 - 48G looks to below:

  #
  activate default domain system
  #
  LLDP enable

  #
  domain system
  disable the access limit
  Active state
  Disable Idle-cut
  self-service-url disable

  #
  rstp STP mode
  enable STP
  #
  NULL0 interface
  #
  GigabitEthernet1/0/1 interface
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/2
  access port vlan 610
  #
  interface GigabitEthernet1/0/3
  access port vlan 610
  #
  interface GigabitEthernet1/0/4
  access port vlan 610
  #
  interface GigabitEthernet1/0/5
  access port vlan 610
  #
  interface GigabitEthernet1/0/6
  access port vlan 610
  #
  interface GigabitEthernet1/0/7
  access port vlan 610
  #
  interface GigabitEthernet1/0/8
  access port vlan 610
  #
  interface GigabitEthernet1/0/9
  access port vlan 610
  #
  interface GigabitEthernet1/0/10
  access port vlan 610
  #

  #
  interface GigabitEthernet1/0/49
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/50
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/51
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/52
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1

  etc...

  Could you help me when I made a mistake?

  THX

  The problem was that solve this problem.

  I have blocked all ports. It was a problem. I change several settings and everything works well.

• Problem VLAN HP Mini 110-4101er

  Hello. We have a level 2 + switch with VLAN. This netbook is unable to obtain an IP address from the DHCP server. Parameters default network has been applied. The same thing with another HP laptop with the same NIC Realtek. But another Acer netbook works fine on the same switch port. We do not know why.
  
  Any help would be appreciated.

  The problem is resolved. Had to download the new drivers and the utility of diagnosis on the Realtek site. With the help of the utility put in place of VLAN ID 0. Everything works fine.

• Ping GS752TP Cant VLAN IP

  I have a switch are not currently connected to the network, which will be repalce one switch of aging there address static IP address 10.100.6.225 and created a virtual local network 50 that will be for the devices of shoretel, put in place a VIRTUAL LAN, whose 10.100.50.227 and active in IP Routing IP address.

  The new switch has a gbic for current media converter will disappear, but I have all ports currently left the vlan1 and ports 1-46 Untagged on vlan 50, if I connect a pc on any port 1-46 I can ping 10.100.6.227 but not 50.227, what don't get me? and how do I configure port 48 which will have a shoretel switch on the network connected on 50?

  Thank you

  Hi Dakota68,

  Sorry for the late reply,

  Please check if the VLAN ID 50 is defined as the PVID for ports 1-46 by going to

  Switch > VLAN > advanced > Configuration of Port's PVID.

  The PVID column for the port 1-46 should say '50' (VLAN ID for VLAN.50)

  Please see more on page 113 here PVID:

  http://www.downloads.NETGEAR.com/files/GDC/GS728TPS/GS7xxTS_GS7xxTPS-SWA_1Mar12.PDF?CID=wmt_netgear _...

  And Yes, I recommend that you create another virtual local network for servers.

  Try and let us know if it works