Start PC fail

Similar Questions

• Starting test FAILED - HP ENVY 1191-NR

  Hey guys/girls,

  New to the forum - need some tech support.  I have a HP ENVY3D 1191-NR running Windows 7.  He recently began closing before you start completely.  I ran a Test at startup and for the following results:

  Memory test: FAILED

  FAILURE ID: QE40XL-5GE6G4-XD0141-400103

  PRODUCT ID: YL748UA #ABA

  Memory module

  Starting test: FAILED

  I wonder if that means the RAM of the computer has gone wrong and I need to replace, or else... ?

  Thanks in advance to all.

  Hello:

  Yes, that could indicate a possible memory module failure.

  What I would do is unplug the PC and remove the battery.

  If the laptop has two memory modules, remove one of them and plug the power adapter.

  See if the PC starts and works normally.

  If so, unplug the adapter, remove the other memory module, put in the first one you took, connect the a/c adapter and see what's the result.

  If the PC does not start, you have isolated the bad chip and you can just buy a new one with the same characteristics.

  If the PC is still under warranty, contact HP for a replacement.

• Starting test failed

  I have a HP Pavilion g4-1125DX with Windows 7. A few days ago while I was downloading the files that it hung. I was able to move the cursor, but could not close the browser window, nor could I stop him. I push the power button down for a few seconds for a hard stop, when I tried to connect the system to the top it wouldn't boot Windows. He gave me several options to save and I tried to perform a restore of Windows, which did not work, tried to start it in safe mode and still have the same error, I gave up trying to save my files that I have most of them supported anyway if I tried to perform a full recovery of the system to the factory settings. He went through the process of recovery worldwide and says that it is successful. When I tried to reboot after recovery, he hung up on the trunk again. He didn't try to make me the same recovery menu. He just hung. I tried another hard stop and restart to get to the HP Advanced System Diagnostics and tried the start-up Test and he FAILED.

  He gave me the FAILURE ID: M4H27W-5NR5SC-MFPV5G-60UQ03.  I don't know what to do with this information. I need help. I just want to get this thing back operational.

  Thank you.

  Hi, LBG,.

  An error 303 is a failure of the short drive self-test and definetely suggested that tough is a failure.

  As your laptop is still under warranty, contact HP by simply using the relevant link below and make arrangements for the disk needs to be replaced.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• HP ENVY laptop - 15-k101nx: HP envy 15 does not start after failing to set up

  Failed to configure Windows (it took so long and shows no percentage) so I turned off my laptop, removed and unremoved battery and turned on it. The problem is it does not start and the screen is all black with little light on it.

  What I've done so far:

  -J' tried to restore the BIOS by following the instructions here say: http://support.hp.com/ee-en/document/c02693833 ; However, I still have the same problem after restoring the BIOS.

  -J' also tried a few hardware diagnostic test, he failed in the test of ' disk hard short dst check "and gave me chess and product IDS.
  -He also failed in the Startup Repair tool

  My laptop is still covered with warranty accdg here 'http://h10025.www1.hp.com/ewfrf/wc/weInput?lc=en&dlc=en&cc=us&tmp_weCountry=&tmp_weSerial=&tmp_wePro... '. but the characters upon receipt of my laptop is already melted aways since they are written on a thermal paper.

  BTW, I can always open the command prompt and the research on the C: drive and see my files, but don't know what to do whenever I used the chkdisk command, it asks me to do things I'm not familiar with.  I just heard that the chkdisk command solves the problem temporarily.
  
  What do you think are the alternatives and solutions to the problem of my laptop?

  Yes the hard drive needs to be replaced. Just call support and they will have it replaced for you under warranty.

• starting system failed at checkpoint [USBd]

  Fact a reboot after upgrade to Office 2000 to 2003 and the screen froze with a blinking cursor in the dark.

  F2, F11 or F12 does nothing.

  Ctrl + alt + tab produces a momentary vision of the start screen and changes to a black screen with the message: «...» "Previous attempts to start this system have failed at checkpoint [USBd]... »

  I need help to get back on the pc. (Dell Dimension 2400 Series, version of the Bios A02), Win XP.

  Hi Befudd,

  We are happy to know that your computer works as expected. Please do not hesitate to answer, in the case where you are facing in the future other problems with Windows.

• Start-up failed, cannot fix, no restart of drives available

  PC HP with Vista. Will not start. Installed recovery options failed and no reboot disk available. All downloadable options which can be copied and used in the option "reboot with the disk?

  Hello

  I suggest that get you in touch with HP for better help.

  Azeez Nadeem - Microsoft Support [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Waterfalls of error on the camera on the Blackberry emulator: starting viewfinder failed

  I try to open a Blackberry device stunts 10.2
  import bb.cascades.multimedia 1.0
  import bb.multimedia 1.0
  import bb.cascades 1.2
  import bb.system 1.2
  {Page}
  title bar: title {} bar
  Title: "QML camera Sample App.
  }
  content: camera}
  ID: qmlCameraObj
  Boolean photoBeingTaken property
  Notecard: {}
  If (photoBeingTaken == false) {}
  photoBeingTaken = true;
  qmlCameraObj.capturePhoto ();
  }
  }
  onCameraOpened: {}
  qmlCameraObj.startViewfinder ();
  }
  onCameraOpenFailed: {}
  Console.log ("camera open failed")
  }
  onViewfinderStarted: {}
  photoBeingTaken = false;
  }
  onViewfinderStartFailed: {}
  Console.log ("ErrorType" + error)
  Console.log ("viewfinder failed")
  }
  onPhotoCaptureFailed: {}
  Console.log ("picture capture failed")
  photoBeingTaken = false;
  }
  onPhotoSaveFailed: {}
  Console.log ("picture save failed")
  photoBeingTaken = false;
  }
  onPhotoSaved: {}
  photoBeingTaken = false;
  }
  onCreationCompleted: {}
  qmlCameraObj.open (CameraUnit.Front)
  }
  }
  }

  I also add appropriate in the .pro and these libraries line at my bar - descriptor.xml

  run_native
  use_camera
  access_shared

  But when I run this code on the emulator, I got in the console: ErrorType 2 viewfinder has failed. If anyone has any idea why the viewfinder does not start, it will be useful.

  You can try on 10.2.1?

  If this does not work, please connect has a bug about the developer Issue Tracker: SAID

• My HP dv6t starting test failed. I can't start windows 7 USB/dvd-drive

  Internet did not work and other things on hp dv6t laptop my son with windows 7 I did a system of resettlement.  It worked for a day and now can get right after loading windows files and then a blue screen with the rays of the Sun.  I can't do anything.  I tried to do a start-up test and it said that the memory test and a smart test passed but the shore that DST has failed.  What does that mean?

  DST-short is the hard drive, he has failed the test, replace the hard drive.

• Disk HARD - short test error start DST FAILED

  Hello!

  I have a problem with my Inspiron 8600 (don't model no PP02X) that started 2 days ago... hard drive appears to be faulty

  It started with the PC freeze, well, I just restarted and after have connected you on the deskop screen came, then it just froze again... and again... and again...

  (discovered an old topic about the same problem here: http://delltalk.us.dell.com/supportforums/board/message?board.id=insp_harddrive&message.id=45306 )

  I ran the F12 diagnostics, he said:

  -Start the test short dst.
  test results: fail
  error code: 1000-0146
  MSG: Unit 0: dst log contains previous error

  and when you run intensive scrutiny with the CD of diagnosis CRITERION of the READ and CHECK it seem to fail (error code 0F00:1344 and 0F00:1 A 44)

  That said this is no longer the original HARD disk, I replaced it with a bigger and a half year ago. I have a box external 2.5 "and when I connect with my other PC HARD drive, it seems, can be accessed without any problem... so can't quite see that HARD drive is 'destroyed '.

  Help, please

  Message edited by HighVoltageHerbie on 04/01/2008 09:54
  
  

• Phone start-up failed

  I bought the new Satellite from Toshiba. Followed the instructions on how to start. He asked me if I would like to remove the hard drive. And don't give me the opportunity to say 'no' so I went with it. It now comes with the following message and I have not found anything on how to fix this.

  * For Atheros PCIE Ethernet Controller v2.0.1.9 *.
  * Check the cable connection! *
  * PXE - MOF: exit Intel PXE ROM.*
  * No boot device - insert boot disk and press any key *.

  Do I need to buy a disc of "boot"? And if so where can I find one?

  Thank you

  Hey Buddy,

  This error message means usually only in the BIOS, an incorrect boot order is set. Have you checked the BIOS? You must set the HARD drive as first boot device.

  > I bought the new Satellite from Toshiba
  Is what laptop exactly?
  For me this seems strange that you have to format the HARD disk on a new computer laptop purchased.

• HP probook 4520 s: start test failed

  Hello, could you help me with the error that I have? Because I can't install windows.

  Hello

  Product number? --
  http://support.HP.com/us-en/document/c00033108

  Which indicates a failing or hard drive and you need to replace the hard disk drive.

  I suggest that to do fast & Extensive tests in the system diagnostics hard drive by typing F2 away as soon as you turn on laptop, to be confirmed. If you get the ID of failure 24 characters or other error codes, it is time to replace the HARD drive.

  If you are in warranty, HP may send you a free of cost.
  http://h10025.www1.HP.com/ewfrf/wc/weInput?cc=us&LC=en

  Otherwise, you could buy any laptop brand to retail SATA HDD at least the same capacity as the one supplied with your laptop. (Eg. 500 GB, 750 GB)

  If you do not have a recovery until now media, must order them for resettlement to the factory settings.

  Contact HP:
  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

  Concerning

  Visruth

• re black screen: start: last good known Config, Windows starts normally begins to start and fails

  This screen offers safe mode options that I didn't choose. When I select to start Windows normally the computer starts to boot and I see the Windows Logo, then it switches to the Logo from my computer with 2 different keys of F and when I looked into it and I tried again, I got the black screen again with these options and it keeps cycling.

  I tried F8 and I don't know enough to navigate. Can I get help? My windows disc seems to be broken, so I'll try another disc. I ran it under Configuration now it says: for installation: format the Partition using the NTFS file system. I don't know how to repair Windows on mine.
  The disc seems to be higher my score 1 digit. It is Windows XP Home Edition. The Windows disk that is scratched is not this edition. I do not know what form of Windows is installed in my BONES.
  I move files off my hard drive when this problem occurred and I got a blue screen and the computer began to dump physical memory... I turned off my computer. Recently, I had the memory stick inside, but it starts normally after that I did until this happened, I thought that this can happen because I changed the memory stick... not sure

  Hello

  Are you trying to clean windows install? Do not pass without taking your databackup as format NTFS means it will erase all your data on the disk, you will have:

  Validate windows

  Reinstall windows update

  Install all required software

  Restore your data

  What, exactly, is the problem. Remove first the cd boot pc, at the prompt when it asks for safe mode - select Safe mode, connect to pc using administrator.

  Click Start-> run, type &-> chkdsk /f c :-> OK

  He may ask you to schedule the scan of the drive-> select Y for Yes, restart your computer.

  I hope this helps.

• Error starting program: failed to initialize the graphics system

  I just upgraded to Windows Vista 64 bit to Windows 7 64 bit.  I now have problems of execution of Roller Coaster Tycoon 2.  I get an error that says: "failed to initialize graphics system '.  I think the problem has something to do with the program you want to run in 256 k colors.  I installed the new video drivers on the Dell Web site, but it did not help.  Any ideas?  Thanks in advance.

  See if you can use a Compatibility Mode setting to run in 256 colors?

  How to troubleshoot a program that does not run as expected once it is installed on Windows Vista
  http://support.Microsoft.com/kb/931362/en-us

  Make older programs in this version of Windows
  http://windowshelp.Microsoft.com/Windows/en-us/help/bf416877-c83f-4476-a3da-8ec98dcf5f101033.mspx

  Windows Vista Compatibility Center
  http://www.Microsoft.com/Windows/compatibility/details.aspx

  Windows 7 Compatibility Center
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

• Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

  Original title: Windows could not start the service of connection manager on the local computer remote access

  amplifier

  Windows could not start the service of connection manager on the local computer remote access

  Error 1068: The dependency Service or group could start.

  Hi sunelchandraoli,

  1. when exactly you receive this error?

  2. you remember to make changes to the computer before this problem?

  Step 1:

  "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

  a. Click Start, type services.msc in the box start the search.

  b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

  c. right click on the Remote Access Connection Manager service and then click Properties.

  d. under the general tab, click Manual next to startup type.

  e. under the general tab, click Start under the service status and then click OK.

  f. also check for long-term services.

  The dependency of 'Remote access connection manager' services include:

  i. secure Socket Tunneling Protocol Service

  II. telephone

  III. Plug-and-Play

  IV. Remote Procedure Call (RPC)

  c. of DCOM Server process Launcher

  VI RPC end point mapper.

  Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

  Step 2:

  You can also try a system restore to a prior restore point you have been affected by the issue.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  To run the system restore, you can consult the following link:

  System restore

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Hope this information is useful.

• 11g - emctl start dbconsole fails

  I have a server that is running OEL 6 64-bit. I installed the 11.2.0.3 Patch Set 2 database. The installation of the database has gone well except for that I can't start the dbconsole.
  
  "emctl start dbconsole" error
  
  I look in the logs located in - /u01/app/oracle/product/11.2.0/db_1/host.domain.com_orcl/sysman/log
  
  First, I look at emdctl.trc and see:
  2012-06-12 09:14:42, 566 ERROR Thread-403838720 hand: nmectla_agentctl: error connecting to the https://olympia.glasfloss.com:3938/emd/main. Return status code
  
  I figure above error is perhaps the result of rather than a cause, so I go to emdb.nohup and see the following:
  
  The most relevant appears to be-
  
  -Tue Jun 12 09:10:41 2012::tzOffset to - 06:00-360 (min), but agent is runnning with tzOffset-300 (min)
  -----
  -Tue Jun 12 09:10:41 2012::trying again after a wait of 1 second to account for the transition from the light of day
  -----
  -Tue Jun 12 09:10:41 2012::tzOffset to - 06:00-360 (min), but agent is runnning with tzOffset-300 (min)
  -----
  -Tue Jun 12 09:10:42 2012::Mismatch detected between the time zone in env (U.S. / Central) and /u01/app/oracle/product/11.2.0/db_1/host.domain.com_orcl/sysman/config/emd.properties (-06:00). Forcing value to...-
  
  
  My OS time is correct
  
  No. date + %z # name of the zone
  product
  -0500
  
  Date
  Kill Jun 12 10:07:17 CDT 2012
  
  It's OK for me since we are in the Central time zone
  
  
  so is this the dbconsole which is misconfigured? did I miss a patch? is the problem with the agent instead?

  Hello

  Have you tried the following:

  #> emctl config agent upadateTZ
  #> emctl resetTZ agent
  #> emctl reload agent
  #> emctl start agent 
  

  Jan S.