Startup after installation problem

Similar Questions

• Equium A200 - startup after update problems

  * After installation from what I understand, is the most recent update for windows vista and when the computer has re boots itself, I am greeted with the following message: *.

  ' + Cannot start WIndows. A recent change in hardware or software may be the cause. To solve the problem: +.
  + 1. Insert your windows installation disc, and then restart your computer.
  + 2. Choose your language settings, and then click "next". +
  + 3. Click on "repair your computer." +

  + If you don't have this disk, contact your system administrator or computer manufacturer for assistance. +

  + File: / Boot? BCD +.
  + Status: 0xc000000f +.
  + Info: an error occurred trying to read the boot configuration data. » +

  * Iv tried to start in safe mode by holding F8 when booting, but this causes just the start screen flashes that light while a sharp peak noise, like an alarm.*
  * Am I right in assuming that when he tells you to insert the disc of windows intillation that it is made reference on the recovery disk 'product' I got with the laptop? If so, I'm reluctant to use this drive as it says on the back of the box "WARNING: If you use the product recovery, you will lose all data on the hard drives..." It is the only option or offer just a funtion of repair that will remove all files that I have a number of very important issues that were yet to be supported in amont.*

  * Any help would be appreciated *.

  * Thank you *.

  * Stores *.

  Thanks for this info stores.

• Startup after installation of McAfee security poblems

  After installation of McAfee security I get say Windows blue screen not not close properly and have to restart in safe mode, then back to the previous state. I can then use Windows in normal mode. I tried to reinstall McAfee several times and each time get the same problem. Is this a problem with my laptop (Toshiba satellite) or security software

  Please uninstall the software and go to the support to McAfee.

• Blue screen on startup after installation of service pack 3

  Original title: big problems with Windows service pack 3

  My pc runs xp edition media with a processor intel dc. I had to reformat using recovery discs cleaning all ok using microsoft update until after that load successfully and the installation of Service pack 3. Start theres a brief flash of B.S.O.D. then it goes straight to load the page option of safe mode. Startup journal raises a whole series of errors. drivers of not start tearing my hair on it!

  If there is a problem starting, XP is configured to automatically try to start again and you can stuck in a loop not being able to go beyond the screen boot options, or none of these startup options you choose will work only.

  Sometimes, when XP has a problem starting or falls down and tries to start again, it will give you a "short" menu of boot options and none of them will appear to be good to get your system going again.  You have tried them all!

  The options are similar to the Advanced Boot Options menu XP, but the only option that you need (disable automatic error system reboot) are not offered, because XP went too far during the boot process and offers a limited number of boot options.

  If this is the case, you must call Options menu advanced boot yourself until you do not see the option:

  Disable the automatic restart in the event of system failure

  When you get the XP Advanced Options correct start menu you want to see, he has options on it like these:

  Safe mode
  Safe mode with networking
  Safe mode with command prompt

  Enable Boot logging
  Enable VGA mode
  Last good Configuration known (your most recent settings that worked)
  Directory Services Restore Mode (Windows domain controllers only)
  Debug mode
  Disable the automatic restart in the event of system failure

  Start Windows normally
  Reset
  Return to OS Choices Menu

  You need to choose in this menu is the option:

  Disable the automatic restart in the event of system failure
  
  Then if XP does not start normally, you will see an error screen with information and clues about the problem and then you can decide what to do next.

  If you do not see the automatic restart on system failure option turn it off, you must reset your system and start typing the key F8 on the keyboard until you see her disable automatic restart on system failure option.

  If you miss the window of opportunity F8, you must try again and start tapping the F8 key with more urgency (earlier and more frequently) until you see disable automatic restart on system failure, and then select.

  You must keep trying the F8 menu until you see disable automatic restart on system failure option, and select it.

  If your system has a Blue Screen of Death (BSOD), we need to know what the screen says:

  Here's a BSOD example showing information you provide:

  http://TechRepublic.com.com/i/tr/downloads/images/bsod_a.jpg

  Send for the nose and the Red arrows (3 to 4 lines total).

  Send all * line STOP message since there are clues in the 4 parameters.

  If it looks like there is some kind of name listed in the STOP message file, send this line also.

  Ignore the boring text unless it seems important to you.  We know what a BSOD looks like, we need to know what your BSOD looks like.

  If your ntbootlog is display messages «Is a not load driver...» ', this does not necessarily mean that a problem...

• I can only start my computer in Safe Mode - system hangs on startup after installation of updates

  Original title: UPDATES DOWNLOADED PROBLEMS to START NORMAL, MUST LOAD IN SAFE MODE - LOST AFTER 30-40 SECONDS VIDEO

  After the download and installation of updates on my desktop Gateway (FX7020) the computer freezes on me and was forced to shut down hard. After a few attempts to start the computer, I was able to get into safe mode. After some time in the exploration of the event viewer I tried out and re-start of normal BONE. I was unable to make it through the boot sequence and had to shut down hard again. I waited a while and it made back in safe mode, but this time after 25-40 sec. I lost the video, the mouse, the keyboard. Everything was running. I've read a few articles and I hope that I don't have a F... THE OS.

  Thanks any help will be graciously appreciated... RA

  Hello

   
  Method 1:
  You can try restoring the system to safe mode and check:
  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
  You can consult the links for:
  System restore
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions
  
  Method 2:
  If the problem persists, you can refer startup Repair in Windows Vista, which is a recovery tool that can fix certain problems. You can check the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

• HP Pavilion HPE h9-1100 Phoen: computer hangs during startup after installation of 970 GTX

  The problem:

  So here's the deal. I bought a new EVGA GTX 970 and installed in my office (after you have uninstalled the drivers for my old AMD GPU). When that I start it freezes on the BIOS screen. Press a button and the screen goes black; It is still frozen. Fan works in beast mode, until I turn it off.

  What I tried:

  • I checked for if sure it was well installed in the x 16 PCIE slot and connectors double checked.
  • Checked to see if my motherboard supports UEFI (it does)
  • Using another monitor using vga instead of as before display port.
  • EVGA called and suggested they updated my BIOS on HP site (I think I'm already on the latest version)?
  • Called HP and they said I have spend $250 to have a technician to work on it. (I'd rather not pay nearly as much as I paid for the card to install it if I can avoid...)
  • Remove the battery on the motherboard for 5 minutes then replace and powered with the new graphics card.

  None of these things had No effect. (with the exception of the money payer which I have not yet made). I put the old card (Radeon 7670) back in and it started late.

  I'm kind of grasping at straws at this point. Any help would be greatly appreciated.

  Model: h9-1100 (A5U16AV #ABA)

  OS: Windows 10 Pro (64-bit)

  Motherboard: Gigabyte 2AC8 (970 (RX980) + SB950 chipset AMD)

  Processor: AMD FX-8150 (3600,0 MHz)

  BIOS: Ang_716 (05/04/2012)

  I would like to know if there is relevant information, that I left out.

  -edit

  I tried to install the card in HP h9 1300 t friend (he also recently installed the same card) it worked fine, if the card is not defective. Then we installed his gtx 970 in my computer. Same results as before. Startup freezes on the bios screen.

  Sure that I narrowed down it to a compatibility problem with my motherboard. I ordered a new one, the ASRock 970 M Pro3 AM3 + / AM3 AMD 970 + AMD SB950 6 x SATA 6 Gb/s USB 3.0 Micro ATX AMD Motherboard (bite). I'll post here once again with results once it arrives here in a few days. I cross my fingers.

  Hello

  The level of the BIOS of your PC is not compatible with the video BIOS in the NVIDIA GTX 970.   You need a BIOS to version 8 HP which is not displayed for your PC.

  BTW - A replacement of the card mother not HP will require a new license of Windows.

• Black screen on startup after installation of the wireless router

  I recently installed a Netgear Wireless - G Router (WGR614) on my computer vista HP laptop and since then, I have experienced a few problems. One day my computer was working fine. I stopped it and when I went to leave the next day morning, the screen was black with a bunch of small lines. It would not load anything so I stop and tried again. It's the same thing. I turned on and close my count, and when I opened it upward a few minutes later the screen was beautiful. Then, I have lived the "Blue Screen of death" 3 times. I researched what the problem might be and thought that I might need to update a driver. I went to HP Health Check and there were a couple of updates on a wireless adapter and a card reader, so I installed the updates. I have not experienced the blue screen since then, but I still have problems with the black screen when starting upwards. If I leave the computer open the black screen turns to a white/blue color and nothing loads. But if I close it then after a minute or two everything is. This could be the cause?

  Hello

  Start with the wireless router is not the cause of the problems. It is a stand-alone device that simply provides a network connection for your system. Offhand, I would say that you experience a hardware failure, and perhaps the time is simply coincidence. Knowing what was the error message stop can help to indicate where the problem lies, but your description of the problem is quite indicative of a hardware problem. Solve it will probably require involving a technician (contact HP if it is still under warranty).

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• PC crashes and a blue screen on startup after installation of updates

  My pc stops and restarts a blue screen when there is an update to download and install. It is well after I installed the update. Is there an automatic Start Up in the "Local View" app that I can start

  [Original title: updates Crash]

  Hi William,.

  If the PC crashes and displays a blue screen whenever you try to install an update, then it could indicate some other underlying problems in the computer. What was the error message displayed when the computer has started a bluescreen?

  Alternatively, you can refer to this article for more information on blue screen errors:

  http://Windows.Microsoft.com/en-CA/Windows-8/resolve-Windows-blue-screen-errors

  Get back to us with the exact error message with any error code displayed in the blue screen, so that we can understand what caused this problem and help you accordingly.

• My effect after installation problem!

  Please help me my Creative could have no effect... and when I try to download it from " " https://creative.Adobe.com/products/AfterEffects "he still will not download starting but other works suitable as well as downloads, but just after the effect not! Please see the vedio to publicize my problem!

  Your computer will not work with the current version of After Effects

  (version 12).

  It will not work with the previous version either.

  Or the version before that.

  Since CS5 (version 10) of After Effects, it has been the 64-bit software. You

  cannot run it on a 32-bit system.

  In addition, you don't have enough RAM.

  See the system requirements for After Effects here:

  http://www.Adobe.com/products/AfterEffects/tech-specs.html

• Dual monitor boot problem with Windows 7 Professional 64 bit after installation of any graphics program like a game.

  I have built this platform with the help of the owner of a store of 4 cumputer teir 2 years ago. We initially put Windows Vista 32 bit on the system to Vista 64 bit unstable atm. For 2 years, the computer worked like a dream. Last week I made a clean wipe of windows vista and windows 7 professional 64-bit installed. The system has two monitors. The primary monitor is a sony bravia with 26 "led and secondary for watching movies is that a 55 '' led Samsung 1080 p 240 Hz. The graphics card is a geforce GTX 295 nividia. It has 12 GB of Ram and the CPU is an i7 965 @3.20.

  The problem I have is this. After the installation of any game average to work with windows 7, the screens to reset their resolutions automatically more than a few times as they are confused. Sometimes, I have to return the screen to its correct resolution after installation in full. Most of the games and then run fine. After installing the game or any game designed for win 7 startup of computers is all messed up for the monitors. After starting hand 26 "sets its resolution and then after about a second 30 pause the computer makes the sound (the double) that it is resolutuons to reset monitor again? After that this second reset about 1-2 minutes the computer is good to go, unless it sets the res evil. The problem is the computer has never done that with vista and it is very annoying say the least. It still freezes the installation of some games. The only way to resolve what I found is the restoration of the system. The computer starts normally and screen ground is defined once she has always been. The only problem is when you install another game, the problem is their new. This problem is worse in some games.

  The latest nvidia drivers have been installed. There is no conflict in the device with the exception of an old printer Manager. The two comes is set to 60 hertz. I searched all over the internet and there seems to be a problem with windows 7 without solution. I am at a loss. Any other information that you need let me know and I'll post it. Thank you!

  Hi ancientone618,

  It sounds almost as if there is a Windows update that is in conflict with your NVIDIA Driver Installer.  I would say to disable automatic updates of Windows to see if it might help:

  http://Windows.Microsoft.com/en-us/Windows7/turn-automatic-updating-on-or-off

  In addition, please see the article with some useful information:

  http://Windows.Microsoft.com/en-us/Windows7/work-and-play-better-with-multiple-monitors

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Boot problem after installation of Linux Mandrake 10

  Hello!
  I installed Mandrake 10 on my computer toshiba tecra S1 laptop.
  But after installation and restart, the laptop stops in sequence starting with the toshiba logo.

  I tried the F12 key to select the boot device, but it does not work.

  If you have a solution to this problem please tell me.

  Thanks in advance.

  Hello

  It is not easy to tell what the problem may be, but it is possible that the boot manager not properly installed.

• Problem with the areo and transparency in Windows 7 after installation of Nvidia Geforce go 6200

  Am having problem with the areo and transparency in Windows 7 after installation of Nvidia Geforce go 6200

  * original title - I'm having a problem *.

  You have the latest drivers?
  http://www.nvidia.com/page/support.html

  Aero - Windows 7 - How to troubleshoot problems with Aero

  (1) first of all, click on the Start button and type in Aero. Now, click on find and fix problems with transparency and other Visual effects of link.

  (2) a new Wizard dialog box opens. Make sure that you click Advanced to solve all problems automatically.

  (3) either the problem will be solved or not. If this isn't the case, you will get a list of items that are potential problems.

  (4) If you want to see more details about the problem, you can click View detailed information. This will give you a list of potential problems that have been verified and those that pose problems.

  If it does not---> click Start---> right click computer---> click Properties

  Click the link for 'Windows performance index' and then click 'rerun the assessment"to refresh your WEI score and try again.

  Note: If you have Windows 7 Starter, or if your system does not meet the requirements for Aero you will not be able to use Aero.

• Had problems with Windows 8 Pro that I bought after the pre version, seems when I tried to reinstall it, kept getting no configure after installation.

  Had problems with Windows 8 Pro that I bought after the pre version, seems when I tried to reinstall it, kept getting no configure after installation.  So I tried a full install without success.  Can you please give some tips to overcome this problem?  I lost the back upward with the resettlement, don't know how, but I have a QuadCore intel 9650 memory of 8 GB, 560 GTX GPU, 120 GB SSD.  Can I install windows 7 ultimate, but I prefer Windows 8 Pro and don't want to pay for it again.

  I suggest you reinstall Windows 7 first, then use your existing Windows 8 Pro key and reinstall Windows 8 Pro from the following link:

  You can download it from there and use your product key to upgrade:

  http://Windows.Microsoft.com/en-GB/Windows-8/upgrade-product-key-only

  You will need to reactivate by phone:

  Activation of the phone:

  1. press the Windows key + X , and then click run, and then type: slui.exe 4

  2. then press the ENTER"" key.

  3. Select your "country" in the list.

  4. choose the option "activate phone".

  5. stay on the phone (do not select/press all options) and wait for a person to help you with the activation.

  6. explain your problem clearly to the support person.

• After the startup Effects CS6 problem

  Hey all,.

  I was wondering if I can get some help. I just summer buy a new Macbook Pro for work, and had Production Premium CS6 installed on it. Ive started all the apps and they work fine after installation and the Enter key.

  For After Effects, however when I try and start it up, I don't not even a splash screen. Just the problem attached dialog. I tried to look on the forums but couldn't find anything on boot problems before the splash screen - the custom of the same program are beginning to start.

  I tried an uninstall and reinstall, the same problem again. When I press OK, it takes me to a screen to suggest a work around, but usually I would like to open the link when it says its got a solution.

  Any help would be greatly appreciated.

  Here is the error screen with what happens:

  

  Thank you

  Adam

  After Effects CS6 must be updated to version 11.0.4 work on modern Mac OS.

• Installation of elements of problems. I always get the info to download the Advisor after installation

  Version of 64-bit items downloaded 4times, installed a desinstallion delete all including the time adobe in the registry. I have alwas get the info to download the Advisor after installation! I have the file on my desktop, but nothing else!

  Hi gerhards34108030,

  I'm sorry that you are having a frustrating installation. You receive the prompt to download the Advisor because a previously installed Adobe app has been incorrectly removed. You can use the Adobe Creative Cloud cleaning tool to resolve installation problems.

  If this does not resolve your problem, we need additional information to solve problems. What is your operating system and which version of elements are you installing? This is Photoshop or Premiere elements?

  Best,

  Del