Startup error code: 0xc0000225.

Similar Questions

• Error code: 0xc0000225

  Hello!

  On my Elitebook 850 with Windows 8.1 G1, now the 0xc0000225 error code appears.

  On Windows xp, 7, 8 and 8.1, I never had a problem with SpeedFan (to indicate temperatures in my notebooks), and it worked fine until I got the Windows updates for 8.1.  Error messages appeared. So I tried to see if it works in safe mode... is when the trouble started.

  I had already done a recovery flash drive on a memory stick before it happened, and when I insert it now and Press f9 I have the option "External hard drive USB" and that choosing the stick led flashes for a few minutes, then I get choose the language and keyboard map.

  After that I go to 'Advanced Options' (the others don't work) and choose "Recovery of System Image" > "Windows 8.1".

  Windows on a panel says that it cannot find a system on this same computer image when I attach an external hard drive with a backup of the system on it, so I cancel that and choose the "Advanced" option

  He 2 options appear:

  1. "looking for a system image on the network' (I have no connection nor a network.)

  2 install a driver.

  Choose option 2, I'm coming to a place where I can choose 'My Computer', where I see:

  "Local drive (" C").

  "RECOVERY (" D").

  "SAMSUNG (E" (the external drive with the complete system and incremental backups on it [made with a free software called "Backupper"]) ").

  "Boot (X (the flash memory stick drive.)).

  From there I don't know how to proceed.

  Any advice would be greatly appreciated.

  PS:

  After the display of the above, I see the ': 'and') ' turned into smileys... as well.

  PPS:

  I just got an email response from the online store, I bought the laptop for: call them tomorrow during the opening hours and they'lll walk me through the process.

  Besites one CD Pro 8.1 to Windows that they also send a CD Pro with Windows 7 with the laptop. It's one I'm going to install.

  I intend to be here tomorrow after the operation to give a report. (In which case it might be useful to other people with this problem).

  .......................................................

  Problem solved! I found a tutoral video, and it's that I posted just below:

  ...................................................

  "Fortunately I did a recovery flash drive on a memory stick." By inserting, turn on the laptop and typing on f9, the LED on the stick flashed for about 2 minutes. Then I could get to the command-line through troubleshooting > advanced options.

  I didn't type immediately in: bootrec /rebuildbcd
  After that, I typed in: output
  Then click on the upper right corner X so closed to the command prompt. Now, I was back on the bright blue screen and chose the closure of the computer option.

  Much to my surprise very happy that my familiar desktop screen has appeared in a few seconds! »

  ........................................

  So here's this video and I just followed the instructions starting at 11:40.

  https://www.YouTube.com/watch?v=o_BN5PPald8

  Thank you.

  The idea is that, by typing "0xc0000225" in the search bar that my message - I just tried - but I'm going to make it more attractive click Accept as Sollution.

  I'll try to post a link to this topic in the trade forum, although I still don't understand why this isn't a commercial part of it.

  I still don't know how to recover my HP Elitebook 850 G1 use my flash drive.

  Fortunately, I found this trick in this video clip that has worked. But I don't know if it will still work. So, it might be useful for many of us to know how the use of the flash (or disc) drive, we did for the recovery...

  PS:

  I just posted here for your suggestion: http://tinyurl.com/peb8hjs

• 13 - c010nr: error code: 0xc0000225

  My notebook said necessary computer factory reset. So I did now the HP logo comes up. I tried F2, F10 F12 and escape to enter in recovery mode is the error code that I said that I need CD installer or usb recovery although I created the recovery drive is no longer viable. What can I do if I need an impage and my warranty has taken late July?

  Miss You Pop!

  Hello

  You can probably buy the recovery cd or usb hp. com or contact hp at 1-800-474-6836

• Yet the startup error code: 1

  Hello. I have a problem. When I start again I get an error: "Configuration error, please reintall the program" I have reinstall but it did not help.

  Pre-training system:

  -Windows 7 64 bit Service Pack 1

  Please help really is important!

  

  (Polish language)

  Error code: 1

  I don't know what you have tried since there are several options to these links.

  You reinstall? If so, have you run the cleanup tool after uninstalling?

• startup error codes

  I get this message at startup 'c:\Windows\system32\config\systemprofile\AppData\Local\omonubil' access denied.  It doesn't seem to affect the operation of my computer, but it's annoying, someone knows how to fix this?

  You could have, or still are, infected by malware; and it could also be a starting top left him entry.

  Malware scan:

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight...

   

  How to use Malwarebytes once it is installed and updated:

  1. open Malwarebytes > click the update tab at the top > get the latest updates.

  2. on the Scanner tab, make sure that thePerform full scan option is selected and then click on theScan button to start scanning your computer

  3 MBAM will now start to scan your computer for malware. This process can take some time.

  4. when the scan is complete, a message box will appear

  5. you must click on the OK button to close the message box and continue the process of Malwareremoval.

  6. you will now be at the main scanner screen. At this point, you must click on the button toview the result .

  7. a screen showing all of the malware displayed the program that is

  8. you must now click remove selection button to remove all the listed malware. MBAM will now delete all of the files and registry keys and add them to the programs quarantine. When you remove files, MBAM may require a restart in order to eliminate some of them. If it displays a message stating that it needs to restart, please let him do. Once your computer has rebooted, and logged in, please continue with the remaining steps.

  9. when MBAM has finished remove the malware, it will open the scan log and display it in Notepad. See the log as desired, and then close the Notepad window.

  10. you can now exit the MBAM program.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the error persists after scanning, use the program to out startup:

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configureAutoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more. Autoruns goes way beyond the MSConfig utility bundled with Windows Me and XP.

  See you soon.

  Mick Murphy - Microsoft partner

• Error code: 0xc0000225 - /windows/system32/drivers/vtaahjnc.sys

  As the title says I'm having HUGE problems currently. I can't get my PC to work more. The error tells me to put on the Windows Vista CD - wich in fact, I did. But surprise - if I put in the disc, nothing happens. I tried to google the problems - and now I'm really clueless. I would REALLY love if someone could help me!

  Hi Draxion,

  A. when it last work very well?

  B. recent changes made on your computer?

  C. do you have external devices attached to your computer?

  D. when exactly do you get this error?

  E. did you restart your computer after you put the vista disc in the drive?

  You can try the following steps.

  Step 1

  Last known good configuration is a Windows startup option that uses the most recent system settings that worked correctly.

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-last-known-good-configuration

  Step 2

  Check if you are able to boot in safe mode.
  http://windowshelp.Microsoft.com/Windows/en-us/help/323ef48f-7b93-4079-a48a-5c58eec904a11033.mspx

  Step 3

  Try to perform a repair of the boot using your vista DVD. You must use a retail or a reinstallation disc disc to perform this step. Here is the link for the Startup Repair.

  Startup Repair: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

  The last step would be to complete the restore of the system on your computer

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  See this link: http://windows.microsoft.com/en-US/windows-vista/What-to-do-if-Windows-wont-start-correctly

  Bindu S -Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• HP15 startup: error code 59571929

  Get the admin. Or password when turned on startup

  Hello

  Try: 46459309

  Concerning

  Visruth

• 0xc0000225 error code - request installation media for Windows 8

  I recently got an Inspiron 15R SE 7520 with pre-installed Windows 8. It has a huge 1 TB hard drive, I decided to divide it into three easier to manage partitions and proceeded to do so using EaseUS Partition Master. When you restart the system, I got the following error message:

  Recovery

  Your PC needs to be repaired

  A required device is not connected or is not accessible.

  Error code: 0xc0000225

  You will need to use the tools of recovery on your installation media. If you don't have any facility (such as a disc or USB device) support, contact your system administrator or the PC manufacturer

  Press Enter to try again

  Press F8 for startup parameters

  Press ESC for UEFI firmware settings

  1. you press on enter. Nothing happens

  2. press F8. Managed to find the option "restore factory settings". Saved and restarted. Nothing happens.

  3 press Esc. Ran the system diagnostics and a few hours later, the result is that everything is fine. Restarted and I'm back to the blue screen with the first message.

  I googled this problem, and all the proposed solutions begin by booting from the Windows installation CD/DVD and run a command at the command prompt. But:

  I don't have any medium of installation of Windows and I can't go to the command prompt.

  I not create recovery discs.

  And the recovery on the hard drive partition does not work.

  My request:

  I obviously need an installation of Windows 8 media. How can I get? I contacted the store where I got the laptop, but they are not you answer, and the application form, I found online does not work for the United Kingdom.

  A final update on this issue:

  I got the DVD of the shop where I got my laptop since. But I couldn't boot from the DVD automatically.  in order to boot from the DVD, I followed the instructions here: http://www.ifixit.com/Answers/View/110162/Add+Boot+Option+using+Insydeh20+setup+utility

  After booting from the DVD, I got to the command prompt, and then run the commands like here: http://itsolutionsblog.net/solution-to-your-pc-needs-to-be-repaired/

  ! BUT! The last command line does not. It must be

  BCDboot c:\Windows /s /f UEFI z:

  without the : after the f. And then, there is a confirmation message that the boot files have been created

  And then my cell phone was able to start normally.

• HP Envy 17: 0xc0000225 error code won't BOOT HP ENVY 17

  Trying to turn on, get the Error Message:

  0xc0000225 error code

  Your PC could not start properly

  The NEW blue screen of death!

  The computer was loaded just a few Microsoft updates last night before stopping.

  10 64-bit Windows

  Where do we go from here?

  The error code and the situation are not addressed by Microsoft and hours of work-around so did not work.  Recovery disk was ineffective as a myriad of Internet solutions.

  I had to buy a CD of Windows 10 for $150, and enter the BIOS to boot from the CD Ms.  Once I had the opening screen, I selected "REPAIR".  2.5 HOURS later, I was back to and all running programs.

  MS scammed me once again... Thank you Bill Gates!

  SDJL THANKS for the reply.

• HP 250 Portable G2: 0xc0000225 error code. Hard drive is not accessible, computer laptop HP 250 G2

  I'm doing a clean Windows 8.1 64-bit as a result of a fall, but I'm getting 0xc0000225 error code, using built-in HP recovery utility. Installing Windows also says: Windows could not retrieve information about the disks on this computer. Kindly help. Thank you

  If your computer is originally shipped with Windows preinstalled by HP (as it should) - it would be better to use the HP recovery media that will repair Windows, applications, and all the default partition to factory. It will use the license of your machine for Windows and should automatically active Windows after installation.

  If you are using the 8.1 Windows installation media, you may need a facility to post license Win (depending on the type of used windows).

  -If you want to use the original that are preinstalled windows, you can get a HP recovery media as described above

  -If you are using the 8.1 Windows installation disc and install Windows from using your driver's license, follow these steps:

  1 boot from the Windows DVD
  2. click on install now
  3. in the configuration screen, click Custom (Advanced)
  4. click on Drive Options
  5. Select the partitions to format
  6. click on Format - this will delete EVERYTHING on this partition - format and delete all partitions
  7. create a new partition, and then select a partition to install Windows on.
  8. continue the installation.

  If the Windows installation disc does not work for the above you can do the following to reformat your hard drive:
  1. download a Gparted ISO from here:
  http://gparted.org/LiveCD.php

  2 burn the ISO to a CD or DVD
  2. start from the CD/DVD of Gparted disk.
  3. use Gparted to delete all partitions on the hard disk.
  4. under 'Device' choose Create Partition Table to a new table partition.
  5. create a NTFS partition (or you can wait and create a partition during the installation of Windows).

  Finally, boot from the Windows installation disc and install Windows.

  Let me know if it works for you

• The configuration of your Pc startup data is missing or contains errors: 0x000014c error code

  Hello

  See if any body can help here... I get this blue screen:

  ************

  RECOVERY

  Your PC needs to be fixed:

  The Configuration of your PC startup data is missing or contains errors.

  file:\\EFI\Microsoft\Boot\BCD

  Error code: 0xc000014c

  You will need to use the tools of recovery on your installation media. If you do not have any installation media (like a disk or a USB device), contact your system administrator or the computer manufacturer.

  Press ESC for UEFI firmware settings

  ******

  First of all, I could enter option 11 and run the factory reset, I was so happy because I thought it won't be easy... but then after I did the factory reset... I get this blue screen. If I press ESC I get into this next screen:

  F1 system information

  F2 System Diagnostics

  F9 boot device Options

  F10 BIOS Setup

  F11 recovery system

  ENTER - continue starting.

  This is what happens when I click on one of these options:

  F1, I enter the system of information without any problem, then I click on to continue and return to the screen last... so I press F2 and super, I'm able to run the Test of memory and hard drive check 100% without any problem in one of those who, after that I'm done with my tests I press exit and I'm back to F1 , F2, menu etc... now I want to try F9, F10 or F11. disappointment in this option 3 I go back to the blue screen described at the beginning of this post. (I already plug in a USB key with a bootloader, which works perfectly)

  so I can't do anything, nothing at all! crazzines.

  So what I did to check why I can't enter BIOS or at least to boot from my USB... I removed the lid of my laptop botton and removed the hard drive and is then, how I was or I am able to log in the BIOS - I made the changes to start USB first, then the HD and that's how I was able to boot from USB - BUT if I connect the hard drive back I'm not able to enter the BIOS or boot from USB - so basically I'm stuck in this blue screen and I can't boot from a USB key, if I connected HD... I can't use any option... no BIOS, nothing... So yet again, I disconnect the HD.

  This is one:

  HP ENVY Sleekbook TS 4

  If you can't access BIOS with the HDD connected, you certainly won't be able to start on the recovery USB. This is indicative of a failing hard drive.

  Install a new drive hard and then start on the recovery key.

• error code 2718 at system startup

  Original title: error code 2718

  I tried to install a HP scanjet 2200c scanner and couldn't make it work. I then uninstalled! Now, when I turn on the computer, I get an error message 2718! It is annoying and would like to know how to solve this problem!

  Hi Boltman619,

  Try these steps and check the result.
  Step 1: Re-enter the Setup engine
  a. Click Start, click Accessories and then click command prompt.
  b. at the command prompt, type the following and press ENTER after each line:
  MSIExec /Unregister
  MSIExec/regserver
  c. start the computer and check the difference.

  Step 2: If the problem continues, check if this error is associated with linked any program currently running on the computer. To do this, try the following steps:
  a. open the article: http://support.microsoft.com/kb/310353
  b. method 2, follow steps 1 and 2, and then restart the computer to see if the problem persists.
  c. If the problem does not persist in the boot, then follow step 3 and step 4 to find out which is the origin of the problem, and once you have found the culprit, uninstall the program and check the result.

  Note: Don't forget to follow the steps in the steps to configure Windows to use a Normal startup state"" section.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• I get the error "on the volume C: default transaction resource manager encountered an error during startup and its metadata has been reset. The data contains the error code. »

  original title: NTFS problem
  Every 5 seconds, I get a warning (event ID 136) that says: "on the volume C: default transaction resource manager encountered an error during startup and its metadata has been reset. The data contains the error code. »

  Immediately followed by an error (event ID 137) that says "on the C: volume default transaction resource manager encountered a one-time error and could not start. The data contains the error code. »

  I am running windows 7 ultimate in any way to solve this problem?
  

  Hello

  This problem occurs if the Windows file system transaction log is damaged. The Windows file system uses the transaction log to retrieve the system transactions when a file error occurs. The system of common log (CLFS) transaction logs may be left in an inconsistent state. When the CLFS transaction logs are in an inconsistent state.
  To resolve this problem, delete the files .blf and .regtrans-ms in the folder % Windir%\System32\SMI\Store\Machine.
  After you restart the computer, the registry regenerates the deleted files. These regenerated files are in a consistent state.
  1. click on Start , type cmd in the Search box, and then click cmd in the list of programs .

  2. click on run as administratorand then click continue.
  If you are prompted for an administrator password or for confirmation, type the password, or click allow.

  3. at a command prompt, type the following command and press ENTER:
  fsutil resource setautoreset true c:\
  Note these steps assume that Windows is installed in the default location, drive C. If this is not the case, adjust the drive letter of the path of the folder to match your configuration.

  4 restart the computer.

  I hope this helps.

• HP Stream x 360 PC Convertible: 0xc0000225 error code

  I decided to do a restore to factory on my HP Stream x 360 Convertible PC and only got halfway through and said that he was able to complete the factory restore.  He wouldn't do anything to get out of this error message, so I restarted the computer.  It now only starts with the HP Logo and reboots, time and again the HP logo.  I tried to do the recovery through the bios, but I got the error mess "error Code 0 x 0000225.  It doesn't let me do anything else.  I don't have a recovery disk.  I used another program of the partition of the diisk and they seem to be there.  It must have been some files that have become corrupt or foires somehow.  I need to know how I can get a recovery disk or usb drive?  I'm really upset because I've had this laptop for a few weeks.  Thank you in advance.

  #HPExpertDay

  This error occurs when the surface of the disc is dirty or issue with parth of recovery on USB.

  For a new set of recovery media, see:

  http://support.HP.com/us-en/document/bph07143

  See also

  http://support.HP.com/us-en/document/c00707939

• Pavillion G6 - 1a52nr: my Pavillion G6 - 1a52nr gets error code (ks.sys) at startup

  My computor keeps restarting because of the error code (ks.sys), it automatically restarts and I can't do anything. All of the suggestions.  And I am not able to troubleshoot since I can't keep it long enough. THX

  The computer back and the main problem was that Skype updated and my laptop computer webcam didn't like that. The conflict was between Skype and Webcam.  He took care of that and also replaced the hard drive had a few deaths on an area if I had them replace the hard drive. The hard drive was not the issue, but I replaced it because they had it.