Status of ISDN

Similar Questions

• VWIC3-1MFT-T1/E1, showing no recorded in CUCM 10.5

  Hello

  I am trying to record E1 and FXO 8 with CUCM 10.5 using mgcp. FXOs are recorded in CUCM but not E1, it shows not registered. I have attached the configuration of the gateway and the CUCM screenshot. I use the software REL C2900, Cisco IOS Software (C2900-UNIVERSALK9-M), T3 Version 15.4 (1)
  EASY SOFTWARE. Please let me if there is no error in my configuration.

  AD_Voice_GW #show ccm-Manager
  MGCP domain name: AD_Voice_GW
  Host of priority status
  ============================================================
  Registered primary 10.20.13.9
  First backup ready 10.20.13.8
  Second backup none

  Current active call manager: 10.20.13.9
  Backhaul/redundant link port: 2428
  Failover interval: 30 seconds
  KeepAlive interval: 15 seconds
  Last keepalive sent: 14:39:48 GMT April 10, 2015 (duration: 00:00:12)
  )
  MGCP traffic last time: 14:39:48 GMT April 10, 2015 (duration: 00:00:12)
  )
  Last failover time: None
  Last hour switchback: None
  Switchback lifestyle: graceful
  MGCP rescue mode: unchecked
  Start time of last backup MGCP: None
  Last backup MGCP end time: None
  MGCP download ringtones: disabled
  TFTP retry count to close Ports: 2

  Backhaul link info:
  The link protocol: TCP
  Remote Port number: 2428
  Remote IP address: 10.20.13.9
  Current link status: OPEN
  Statistics:
  Recvd packages: 1
  Recv failures: 0
  Xmitted of packets: 2
  Xmit failures: 0
  PRI ports in return:
  Slot 0, VIC 0, port 0
  Automatic download of configuration information
  =======================================
  The current version id: 1428657466-23cb555c-fb36-457e-81fa-58438df308d4
  Last downloaded-config: 00:00:00
  Current situation: waiting for orders
  Configuration of download statistics:
  Download tried: 1
  Successful upload: 1
  Download failed: 0
  TFTP download failed: 0
  Configuration has attempted: 1
  Successful configuration: 1
  Setup Failed (Parsing): 0
  Configuration (config) Failed: 0
  Last command upload config: new registration
  FAX mode: disable
  History of configuration error:
  AD_Voice_GW #.

  ==============================================================================

  D_Voice_GW #show ISDN status
  Global ISDN Switchtype = primary-net5

  %Q.931 is back at CCM MANAGER 0 x 0003 lis 0. Out of layer 3 can not appl
  There

  ISDN Serial0/0/0: interface 15
  DSL 0, the interface ISDN Switchtype = primary-net5
  L2 Protocol = 0x0000 L3 = MANAGER of CCM protocols Q.921 0 x 0003
  Layer 1 status:
  SHUTDOWN
  Status of layer 2:
  TEI = 0, CES = 1, SAPI = 0, status = TEI_ASSIGNED
  Status of layer 3:
  0 active Layer 3 call (s)
  CCBs active dsl 0 = 0
  The free channel mask: 0x00000000
  Number of L2 ignores = 0, ID of Session L2 = 0
  Total allocated ISDN TSC = 0
  AD_Voice_GW #.

  =====================================================================================

  AD_Voice_GW #show mgcp endpoint

  E1 0/0/0 interface

  GIS-TYPE V-PORT ADMIN ENDPOINT NAME
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_G: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place
    [email protected]/ * / 0/0/0 _Voice_: 15 place

  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW
  [email protected]/ * / _Voice_GW

  AD_Voice_GW #.

  Since ISDN layer 1 was showing as Deactivated/Shutdown, crc4 framing so could cause.

  regds,

  Aman

• SX20 and link ISDN with TC6

  Hi guys,.

  I recently upgraded a SX20 and link ISDN to the new TC6 and after the upgrade, I can't make ISDN call.

  I can see and manage the ISDN link from the SX20 configuration web page, but the status of the ISDN connection is: error, SIP not saved.

  I use H323 network and I don't use SIP between SX20 and ISDN link and with the old version, I could receive and make calls. Now when I try to dial the ISDN using the new interface TC6 endpoint indicates that it does not find the ISDN link.

  Thank you for your help,

  Adrian

  Hi Adrien, Valentine's day.  Theres something happens with outgoing enabled on the link and the Codec for this, and we have two CDETS opened on them.  There are always SIP service is enabled on the Codec with link and link itself.  Codec uses IPV6 local links for the link itself.  Even if the sip xstatus on the codec has its inactive etc, the codec message still SIP REGISTER to the device registration link.  Link runs a FWD SIP process that handles the request.  Sorta like a mini SIP registrar if you want.  Codec will send the message to REGISTER using link-local IPV6 address.  Example of message is less than 200 Ok.

  77582.64 SipPacket PacketDump: Proto: SIP, name: REGISTER sip: [0000::000:0000:0000:cd39]: 15070 SIP/2.0, Direction: outgoing, RemoteAddress: [0000::000:0000:0000:cd39]: 15070, GroupEntity: b27d07c1f5f298c492db68040b320ca6, time: 77582634 content:!

  77582.64 SipPacket REGISTER sip: [0000::000:0000:0000:cd39]: 15070 SIP/2.0

  77582.64 SipPacket Via: SIP/2.0/TLS [fe80::250:60ff:fe83:c52a]: 5061 branch; = z9hG4bK45a7681a50ebbdc5b98e2f91bff6b438.1; rport

  77582.64 SipPacket Call-ID: b27d07c1f5f298c492db68040b320ca6

  77582.64 SipPacket CSeq: 47083 REGISTRY

  77582.64 SipPacket Contact:

  «': 5061; transport = tls >; + sip.instance =»

  77582.64 SipPacket of:; tag = 116a994ac2281c72

  77582.64 SipPacket to:

  77582.64 SipPacket Max-Forwards: 70

  Road to SipPacket 77582.64:

  77582.64 SipPacket allow: INVITE, ACK, CANCEL, BYE, update, INFO, OPTIONS, CONSULT, INFORM

  77582.64 SipPacket User-Agent: TANDBERG/518 (TC6.0.0.876266)

  77582.64 SipPacket expires: 3600

  77582.64 SipPacket authorization: Digest-nonce = "d9605a7da8be22af8c0e7f52b3de4a5f5125fcd3", domain = "MARCIE", qop is auth, username = "djkvvknn", uri is "sip: [0000::000:0000:0000:cd39]"

  ", response ="3b27b753cb9bcf38cc2431b767bce643", algorithm is MD5, nc = 00000002, cnonce ="84addca2a68f6c5f9b657a94653a4bae"

  77582.64 SipPacket supported: replaces, timer, 100rel, gruu, way, way out

  77582.64 SipPacket Content-Length: 0

  77582.64 SipPacket

  77582.64 SipPacket >!

  -----------------------------------------------------------------------------------------------

  77582.65 SipPacket SIP/2.0 200 OK

  77582.65 SipPacket Via: SIP/2.0/TLS [fe80::250:60ff:fe83:c52a]: 5061 branch; = z9hG4bK45a7681a50ebbdc5b98e2f91bff6b438.1; rport = 41246; receipts = 0000::000:0000:0000:c52a

  77582.65 SipPacket Call-ID: b27d07c1f5f298c492db68040b320ca6

  77582.65 SipPacket CSeq: 47083 REGISTRY

  77582.65 SipPacket of:; tag = 116a994ac2281c72

  77582.65 SipPacket to:; tag = e84d13204776ebc2

  77582.65 SipPacket server: fwd

  77582.65 SipPacket Contact:; (+ sip.instance =""

  77582.65 SipPacket Content-Length: 0

  77582.65 SipPacket

  77582.65 SipPacket >!

  -------------------------------------------------

  I removed my own addresses, so you get the picture here.

  It is the same for the link.  Link will send REGISTRY as well to himself.

  Even if your using H320 as outgoing Protocol call, messaging between the codec and the liaison unit is still SIP as the outgoing call is still SIP of the codec for the link even if you chose H320.

  You can see all happening all by running: Journal ctx sippacket debug 9 and connect the output to see the messaging back and forth between devices.  This is why the Service SIP on the codec cannot be disabled.

  The outgoing enabled on both devices and it records not as what Adrian has met is odd. So the question has been filed and is under investigation.

  CSCue57128 - SIP in a strange state connecting to link ISDN (Codec)

  CSCue73049 - outbound SIP on ISDN link activation causes lose her registration (link)

  These are new, so the visibility may not be there yet.

  If you see a problem with the link is not not able to register, check to see if outgoing SIP are enabled on the link.  If so, turn it off and start.

  Do the same on the codec as well.  Disable outgoing SIP and restart the computer.  There may be some cases, you do not see this, as the investigation continues with the bug above two ID's

  I hope this helps.

  VR

  Patrick

• People scan status

  On my MBP, I see the the following information when I click on people in the sidebar of Photos.

  

  However, when I click on the people in my 27 iMac it goes always directly to page list all the people who exist in the data of my people.

  Is it possible to get the status information shown above for the MBP?

  If there is no statue, then the analysis is completed on this system

  LN

• Sierra, stuck in the 'Downloaded' status

  The Sierra dmg has failed with an error "invalid checksum". I would like to re - download the file to see if it has been altered during the download - but the app store has the gray Sierra drop-down selection in a status of "downloaded".

  How can I redownload the dmg file and try again?

  Finder > Applications

  Don't you see macOS Installer Sierra?

  If so, place the macOS Installer Sierra in the trash and try to download it again.

• Disappears from the status bar

  When I'm away from mobile data my status bar disappears.

  What mobile data?

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

• C error: ld: library not found for - introduction collect2: error: ld returned 1 exit status

  I'm trying to compile the "Hello World" code C base with gcc, but the following error message:

  LD: library not found for - introduction

  collect2: error: ld returned 1 exit status

  The code itself is nice, he ran into another computer with no problems.

  First gcc had manually, the problem, installed and then uninstalled and installed with homebrew and still have the problem. How can I fix?

  (Have the 5.1.0 version of gcc)

  Okay, so nobody has responded, but I found a solution. This is the version of gcc, apparently more recent versions have this bug, one that works and compiles the codes is the 4.9 version, in case it would be useful to someone.

• Is it possible to add a mute icon on the status bar

  I understand the desire to keep the clean status bar, but a mute icon would be really useful for many users. This is my first iPhone and I had a LIFEPROOF case to protect it. The problem is that this case does not allow me to determine the setting of the switch ring looking from the side of the phone. The only way that I can know if the ringer is on is to flip the switch back and forth while watching the status of ringtone icon screen.

  Yyou possibly tell there is a problem with the case, but I bet it's true for most cases, in particular the raincoat water ones.  If Apple does not support to add even an icon to the status bar at least Apple could put on display today ' hui / Notifications of menu drop-down.

  You can provide feedback to Apple here, http://www.apple.com/feedback. This is a user to user support forum, and Apple is not here involved. It is the only way for them to know you want to see a change.

• check the status of the guarantee

  I don't know the date of purchase my Iphone. How can I check my warranty status?

  https://checkcoverage.Apple.com/

• iCloud Apple music status is incorrect

  I have about 50 + songs that tend to sync my iPod Classic because they (wrongly) show Apple music iCloud status.

  The songs are all ripped to my own CD or LP/EPs and imported music in iTunes.

  I use two Match iTunes and am a subscriber of Apple's music. My version of iTunes is 12.4.3.1.

  Old bandages show removing the download (song) and the new download should be properly thru, but a test of several different songs give the same incorrect state music Apple iCloud.

  Someone at - there a way to fix this?

  Thank you

  David

  Yes, I had this problem also. I contacted apple support and their engineers reset my library to an end and it solved the problem, but there are a few songs that could not be reset, in which case Apple gave me the credit to buy the song again, and that fixed the issue

  bbEst thing to do is to contact Apple support speak to a Manager or consultant and explain to them and you want to reset your library. You may need to disable iCloud music library while reset happens that it worked for me, it will be useful

• I just installed an airport extreme router and WiFi works, but the status light still flashes.

  I just installed an airport extreme router and WiFi works, but the status light still flashes.

  Open airport utility... Click EI... and see what the cause of the problem. It will give the list of questions on the summary page. Click on each of them and he will offer you even solutions.

  for example the firmware needs to be updated... nothing major... or DNS is wrong or double NAT...

  Without our crystal ball, we do not know what is the issue.

• What happened to the download status bar in Firefox 42?

  I can't say when a download is finished, what happened to the status bar in Firefox version 42?

  Type of topic: customization< enter > in the address bar.
  In the new window, look for the icon. When you find it, press and hold
  the left button on it and move it to where you want it to be.
  You can move the icons you want here, but
  some icons are locked in place.

  Also, there is a default button in the Middle at the bottom.

  Photo 1, that's what it looks like in the window customize.
  Photo 2, this is what it looks like on the toolbar.

• How to follow the direction of Adobe 'Flash uninstall"to check the Firefox browser for the 'status' of Adobe Flash? --

  I downloaded Adobe uninstall (for Mac, OS x 10.4ff) and he ran to get rid of old shards of Adobe Flash, be very careful to follow the Adobe provided through their Web site. The last thing they ask you to do is to "Check that the uninstall is complete", by restarting your computer and then open your browser and check the status of the Flash Player. BUT it seems not to be a way to check the State of Adobe Flash Player on current versions of browsers Mozilla product.
  How can I check that the old version of 'Flash Player' is really gone?

  Firefox 41.0.2 on Mac OS X 10.8.5

  edited by e-mail from the public and robots to spammers

  See also the "tools > Modules > Plugins" (topic: addons) page and all: plugins page.

• Why Techtool and disk utility reports different SMART status?

  my laptop sometimes starts the sign of prohibition, and some start successfully.

  I guess it's the HARD drive, that this assumption holds up to what otherwise. All the Apple hardware test has passed including the extended version.

  the image below illustrates the tool of technology S.M.A.R.T status report is a failure because of "current pending sector count", while the State SMART Disk utility report is checked.

  who should I believe? or should I suspect the flex cable?

  

  

  Hi chemotkbiloIn, first of all save all your data now. I would tend to believe TT. But you don't have to guess, the best way to find out would be to bring your Mac to any Apple store for a free evaluation.

• extend the status bar

  the Manager of the activity is not real-time enough, the status bar I cannot get to expand.
  imap accounts migration from one server to another, really needs to see the overall situation in real-time with what thunderbird done and finished. IM open to the addition of an addon, but have not found a good fit for this challenge.

  Try mailtweak, with the option "Cache status message" .

  If it does not immediately install, install first of all this add-on .

  Alternative download site: http://mirrors.ibiblio.org/mozdev.org/mailtweak/