stop 0x0000007A address 80791A5C base at 80782000 datastamp b 45, 02660
What is this error?
Hello
1. when exactly did you receive this error message?
2 did you change on your computer?
3. What is the exact error message?
Method 1:
Step 1:
I suggest you to control in safe mode and run clean boot.
Advanced, including safe mode startup options
http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
Step 2:
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135
Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.
Method 2:
Stop error message when you put a computer that is running Windows Vista or Windows Server 2008 mode hibernation: "STOP 0x000000A0," "STOP 0x0000007a" or "STOP 0 x 00000077.
http://support.Microsoft.com/kb/967352
Tags: Windows
Similar Questions
-
I had this problem with my computer, running Windows Vista Home Premium 32 bit, for several months now, where it will show the blue screen of death shows the error message above. It will be at random times, it seems to just freeze and sit there for a few minutes and then display the error message. I tried chkdsk, System Restore, defragment the HARD disk, running analysis antivirus/antispyware, security scans, check the registry errors, have all the updates and everything I can think of nothing. I saved some of the previous error messages that he brang upward in the same way if they can help with what either.
* [date - 16/06/09; 8:00p.m.] KERNAL_DATA_INPAGE_ERROR
Stop: 0x0000007A (0xC0415BBO, 0x000000E, 0x35AED860, 0x82B76000)
Storport.sys - address 82B 76000 based B 82, 41000, Datestamp 49e01ef7.* [day - 17/06/09] Stop: 0x0000007A (0xC000000E, 0x259268C0, 0xC0438A40, 0x87148EC4)
* DRIVER_STATE_POWER_FAILURE
Stop: 0 x 00000095 (0 x 00000003, 0x83AD8B70, 0x8560D2B0, 0 x 84417808)* [day - 27/08/09] DRIVER_STATE_POWER_FAILURE
Stop: 0x0000009F (0 x 00000003, 0x8611E030, 0x8611E030, 0xAS09E5B8)Pura9910
Hello
If a PC you can try reseating all the memory cards and cables (both ends) - are not just tight - actually remove
and replace. Remove ALL power before opening the case.95 is a Plug n not specified ' error to play and no help.
9F is usually power associated - powersupply thouugh, there might be question of device or driver and antivirus related.
7A
Cause
Frequently, you can determine the cause of the error status (parameter 2) KERNEL_DATA_INPAGE_ERROR bug check. Some common status codes are:
- 0xC000009A or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of non-paged pool resources.
- 0xC000009C or STATUS_DEVICE_DATA_ERROR, generally indicates bad blocks (sectors) on the hard disk.
- 0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose wiring, termination or that the controller does not see the hard drive.
- 0xC000016A or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk.
- 0xC0000185 or STATUS_IO_DEVICE_ERROR, indicates improper termination or defective cabling devices SCSI or two trying to use the same IRQ.
These status codes are common ones that have specific causes. For more information about other possible status codes that can be returned, see the Ntstatus.h file in the operating system Microsoft Windows Driver Kit (WDK).
Another common cause of this error message is the defective material or failing RAM.
A virus infection can also cause this bug check.
Solve the problem
Solve a problem of bad block: Generally, a status I/O of 0xC000009C or 0xC000016A code indicates that the data can not be read from the disk due to a bad block (sector). If you can restart the computer after the error, Autochk runs automatically and tries to map the bad sector so that it is more used.
If Autochk does not scan the hard disk for errors, you can manually start the disk scanner. Run Chkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and run Chkdsk/r.
Warning If your system partition is formatted with the FAT file system the long file names that use the Windows operating system could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.
Solve a defective hardware problem: If the State of e / is C0000185 and the paging file is on a SCSI disk, check the cabling and SCSI termination for problems.
Solve a problem RAM failure: Run the hardware diagnostics feeding by the system manufacturer, especially the memory scanner. For more information about these procedures, see the manual of your computer.
Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.
Check the system log in Event Viewer for additional error messages that might help identify the device that is causing the error. You can also disable caching memory BIOS to try to resolve this error.
Make sure that the latest Windows Service Pack is installed.
If the previous steps do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can cause this error.
Solve an infection by the virus: Search your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.
--------------------------------------------------------------------------
It's my generic bluescreen convenience store which may help.
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
information on all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good.
-
Hi, I get a blue screen frequently with the below error message."Technical information:A problem has been detected and windows has shut down to prevent damage to your computer.
STOP: 0X0000008E (0XC0000005, 0XBF9568C8, 0XA6864C00, 0X00000000)Win32k.sys - address BF9568C8 base at BF800000, Date stamp 4ff2f633
Beginning physical memory dump.Complete physical memory dump.For more assistance, contact your system administrator or technical support. "I am using Packard bell Easynote MX45.XP Home edition Version 2002SP3Inter (R) CPU [email protected] GHz.3 GB Ramcould someone help me fix it please.N
You are better able to tell us if the problem is resolved. Continue to run Malwarebytes about once a week. If the BSOD ceased and MBAM does not show any other infection, you're probably good.
-
I have a Dimension 3000 bought in 2005, upgraded to 2 GB of RAM.
I recently implemented almost from scratch, because Opera program and profile would be repeatedly corrupted, making me lose the email. (This reappeared even after reinstall opera clean, do not use old messages or other profile files). Therefore, I restored a backup of the C: partition Ghost (there are others for my data and downloads) I did shortly after the purchase, after which I had installed only Ghost and two games (I uninstalled the games). I installed SP3 and ran Microsoft Update. I was trying to reinstall other programs that I use now. It's Rhapsody; one of my kids 'synchronize' a player MP3 Sansa Fuze with Rhapsody.
A few days ago when closing Internet Explorer, I got a message that should be closed and I could send a report to Microsoft. It is also used to happen before, from time to time.
Then, more recently, when I closed Rhapsody, I got a blue screen with a message that there was a problem. He said I could try to change some settings in the BIOS. I remember what happens before I restored the ghost of 2005 BU. I looked in the BIOS and not able to find the parameters referred to in (something like memory cache). I wish it were possible to print these messages on a blue screen. I didn't copy the entire message, but I write these references:
STOP: 0X0000008E (0XC0000005, 0XBF8B6C11, 0XA9538368, 0X00000000)
Win32k.sys - address BF8B6C11 base address BF800000 DateStamp 4C7d06ce
This means almost nothing to me. I hope that someone on the forum knows what this means and can suggest what could be the problem.
So far, I have not had more wrong with Opera, so there may be two distinct problems. OTOH, I reinstalled only Opera on 10/12/10; I can still have problems with it.
Hello
Here is more information on the bug 0x8E control: http://support.microsoft.com/kb/945658/
The 0x8E KERNEL_MODE_EXCEPTION_NOT_HANDLED can be caused by a faulty service/driver, damaged hard drive or defective display card not enough space, or memory, Hardware/software incompatibility and third-party remote control software. So to get started:
1. test your memory. Run Memtest you can download from http://www.memtest.org/#downiso. Download the ZIP file, extract the ISO and write on CD. Once written to CD, boot your PC with the CD and run Memtest. Allow the test to run by at least 3 passes or until it gives errors. If you have more than 1 memory module, run the test on each module separately. Try running Memtest from a cold - start unplug your PC for an hour to cool down, then immediately run memtest again when you next turn on the. This way memtest will run when the memory is cool and after the 3rd pass when the memory is hottest.
2. update your display driver. Reference Dell seems to have highlighted 3 different models of Dimension 3000 and so there is 3 different Intel display drivers. See if you can find an updated driver on the Intel Web site. If you use a graphics add-on card try to find an updated driver from the manufacturer's website. If you have any trouble finding a driver let us know what brand and model of graphics card you have.
3. update the Rhapsody software. (I think it's the software you using http://www.rhapsody.com/-software ?). If it's Rhapsody software I think it seems to integrate into your Web browser and it's perhaps why Opera and now IE are mistakes? You can uninstall Rhapsody for a while just to see if it is the reason for your BSOD.
4. when the 0x8E BSOD is caused by win32k.sys, yours, is it then possible, it is caused by control software remote third. It can include programs such as VNC, PCAnywhere, etc. of Teamviewer, RAdmin. If you use one of these programs, uninstall it and see if the PC stops mistakes.
5 run a scan on your hard drive. You can check your hard disk for errors by going toStart ->Run -> type chkdsk c: /r -> clickOk . When asked if you want to force a sayNodisassembly. When asked to plan the audit at the next startup, Yes. Reboot your PC to allow running chkdsk.
Alternatively, you can run a diagnostic on your hard drive. This by downloading the diagnostic program from your hard disk manufacturer. A list of manufacturers and their diagnostic tools can be found here: http://www.tacktech.com/display.cfm?ttid=287. Once more, download the ZIP file, extract the ISO and write to CD. A time written on CD, boot your PC with the CD and run the test Advanced/extended.
Also make sure you have enough hard disk space. It is always recommended, if possible, to have at least 15% of your free hard disk capacity.
6. Finally, take a look in your event viewer when the BSOD for possible errors. You want to look especially in the system and Application logs (and maybe Internet Explorer connects). You can run Event Viewer by going toStart ->Run -> type eventvwr.msc -> pressOk -> event viewer screen opens. If there are errors listed in one of the newspapers type them in your next post if you are not right.
Reading your post I see 3 specific issues, that you might want to focus:
-The memory you added (run Memtest) and hard drive (run Chkdsk)
-The Rhapsody program - try to update or uninstall.
-The software was initially corrupted until you make the first image after the purchase. So you just ghost the problem on.
I hope this helps. Good luck.
-
I have a Hewlett-Packard HP ProBook 4510 s 32-bit with Windows 7 Home Premium and a blue screen appears always * STOP: 0x0000008E (0xc0000005, 0x00000000, 0x8BB32B66, 0xB6F93F6C) * iaStor.sys - address 8BB32B66 base at 8BAF1000, Datestamp 4a7c1b38
Hello
Check with the help of HP, their online documentation and drivers, diagnostics and ask
in their forums about known issues with this model.Support HP & drivers
http://welcome.HP.com/country/us/en/support.htmlContact HP
http://welcome.HP.com/country/us/en/contact_us.htmlHP forums
http://h30434.www3.HP.com/PSG/=======================================================
Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65===============================================================
BCCode: 8th 0x0000008E is the same as 0x1000008ETwo main causes of these blue screen video drivers and BIOS - check with the system manufacturer
Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
other pilots to check there. Disable the installation of self as those who are older and if
Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.See the methods of update driver generic and verify the implementation of driver verifier in the next
Message.BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.
0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
* 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers to 7
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlStop Windows 7 to automatically install device drivers
http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/How to disable automatic driver Installation in Windows 7 / Vista
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
Ultimate and Enterprise)
http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlHow to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">
-
BSOD Stop: 0x0000007A (0xC000000E, 0xF758c825, 0XC03DD630, 0X337F8860)
For the last two weeks, I received a stop erro: on the BSOD kernel_data_inpage_error. I tried to fix according to the instructions, but it happens more frequently now. The technical info is as follows:
STOP: 0X0000007A (0XC000000E, 0XF758C825, 0XC03DD630, 0X337F8860)
NTFS.sys - address F758C825 base at F7539000, DateStamp 48025be5
Thank you
Hello
Error code KERNEL_DATA_INPAGE_ERROR STOP: 0x0000007A indicates that the data page of the kernel of the required paging file could not be read into memory. It seems that there are some problems with the hard drive.
Use the check disk command for all errors on the hard drive.
Warning: We recommend not to interrupt the CHKDSK process. Microsoft does not guarantee the integrity of the disk if the CHKDSK program is interrupted. Security, you can back up your data before using check disk drive.
Use the drive control as follows:
1. click on start.
2. in the search box type 'cmd' and ENTER. Right click and select "Run as Administrator".
3. type at the prompt in the command CHKDSK/p and press ENTER to scan the drive.
4. type CHKDSK C: /F /R and press ENTER to repair corrupt sectors if there is.NOTE: The root of the drive should be C: and drive can schedule a task to start the system, if this is the case, press on is to schedule a task, and then restart the computer to run chkdsk.
Warning of Chkdsk.
Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost
When chkdsk is finished, boot up to the desktop, and then check.You can check the link below for more details - mentioned
http://msdn.Microsoft.com/en-us/library/ms793989.aspxSee also:
http://support.Microsoft.com/KB/174630
I hope this helps. Let us know the results.
-
STOP: 0x0000007A - new large hybrid drive; no model BSOD
I put a 1 to Seagate hybrid drive in a Samsung R580 laptop and reinstalled Windows 8 House (64-bit).
I now get to chance the Kernel_Data_Inpage_Error with the following code:
STOP: 0X0000007A (0XFFFFFFFFC000000E, 0X000000000DFE1860, 0XFFFFF6FC40006E00, 0XFFFFF88000DC0630)
Partmgr.sys address FFFFF88000DC0630 base at FFFFF88000DB2000, DateStamp 4f641bc1
Clearly, this means something, but how can I know what it means? Googling, it does not reveal anything!
I thank very you much in anticipation.
HelloDo you use a SSD? Or RAID? Double control "EVERYTHING" on the hard drive.
controller and wiring (from the discontinuation of ALL power first).
--------------------------------------------------------------------------------------------------------------Resolution in Windows 7 stop errors (blue screen) - has a section for if you can or cannot start Windows.
http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available the onedrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.Adding files to your OneDrive
http://Windows.Microsoft.com/en-us/Windows-8/getting-started-onedrive-tutorialA disk - sharing files and folders and change the permissions
http://Windows.Microsoft.com/en-us/onedrive/share-file-folderZIP or download the content of the C:\Windows\minidump
Use OneDrive to upload collected files
-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
(also Windows 7)
http://www.winvistatips.com/disable-automatic-restart-T84.html===========================================================
BCCode: 7A 0x0000007A
The main causes of this error are virus/malware, drivers, memory, and disk damage. And
It may even be combinations of those so meticulous control of all is needed. Possible addition
the causes are such as the motherboard damaged material errors or other materials.BCCode: 7A 0x0000007A
Bug Check 0x7A: KERNEL_DATA_INPAGE_ERROR
The KERNEL_DATA_INPAGE_ERROR bug control has a value of 0x0000007A. This bug check indicates that the data page of the kernel of the required paging file cannot be read into memory.Important info if you received a STOP Code
If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.
If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.
These actions could prevent a mistake like this does not happen:
- Download and install updates for your computer from Windows Update device drivers.
- Scan your computer for computer viruses.
- Check your hard drive for errors.
KERNEL_DATA_INPAGE_ERROR parameters
The four parameters that are listed in the message can have three possible meanings. If the first parameter is 1, 2 or 3 and the third parameter is 0, the parameters have the following definitions.
Parameter Description 1
The type of lock which took place (1, 2 or 3)
2
The error status (usually a State of I/O code)
3
If lock Type is 1: the current process
If lock Type is 2 or 3: 0
4
The virtual address that could not be paged into memory
If the first parameter is 3 (and the third parameter is nonzero) or 4, the parameters have the following definitions.
Parameter Description 1
The lock type that was held (3 or 4)
2
The error status (typically an I/O status code)
3
The address of the InPageSupport structure
4
Failing address
Otherwise, the parameters have the following definitions.
Parameter Description 1
The address of the page table entry (PTE)
2
The error status (usually a State of I/O code)
3
The PTE contents
4
Failing address
Cause
Frequently, you can determine the cause of the error status (parameter 2) KERNEL_DATA_INPAGE_ERROR bug check. Some common status codes are:
0xC000009A or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of non-paged pool resources.
0xC000009C or STATUS_DEVICE_DATA_ERROR, generally indicates bad blocks (sectors) on the hard disk.
0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose wiring, termination or that the controller does not see the hard drive.
0xC000016A or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk.
0xC0000185 or STATUS_IO_DEVICE_ERROR, indicates improper termination or defective cabling devices SCSI or two trying to use the same IRQ.
0xC000000E or STATUS_NO_SUCH_DEVICE, indicates a hardware failure or an incorrect drive configuration. Check your cables and check the disk with the available from the manufacturer of your drive diagnostic utility. If you use old PATA (IDE) disks, this status code may indicate a bad master/subordinate drive configuration.
These status codes are common ones that have specific causes. For more information about other possible status codes that can be returned, see the Ntstatus.h file in the operating system Microsoft Windows Driver Kit (WDK).
Another common cause of this error message is the defective material or failing RAM.
A virus infection can also cause this bug check.
Resolution
Solve a problem of bad block: Generally, a status I/O of 0xC000009C or 0xC000016A code indicates that the data can not be read from the disk due to a bad block (sector). If you can restart the computer after the error, Autochk runs automatically and tries to map the bad sector so that it is more used.
If Autochk does not scan the hard disk for errors, you can manually start the disk scanner. Run Chkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and run Chkdsk/r.
WARNING if your system partition is formatted with the FAT file system, the long line that names the windows operating system uses could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.
Fix a defective hardware problem: If the State of e / is C0000185 and the paging file is on a SCSI disk, check the cabling and SCSI termination for problems.
Resolve a problem RAM failure: run the diagnostics of material feeding by the system manufacturer, especially the memory scanner. For more information about these procedures, see the manual of your computer.Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.
Check the system log in Event Viewer for additional error messages that might help identify the device that is causing the error. You can also disable caching memory BIOS to try to resolve this error.
Make sure that the latest Windows Service Pack is installed.
If the previous steps do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can cause this error.
Solve an infection by the virus: check your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.See also - control bug 0x77 (KERNEL_STACK_INPAGE_ERROR)
BCCode: 7A 0x0000007A<-- read="" this="">
* 1137.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-Data-InPage-Error-0x0000007A-=============================
If you need search malware here's my recommendations - they will allow you to
scrutiny and the withdrawal without ending up with a load of spyware programs running
resident who can cause as many questions as the malware and may be more difficult to detect as the
cause.No one program cannot be used to detect and remove any malware. Added that often easy
to detect malicious software often comes with a much harder to detect and remove the payload. Then
its best to be thorough than paying the high price later now too. Check with them to one
extreme overkill point and then run the cleaning only when you are sure that the system is clean.It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
the regular windows when you can.TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
It will display all the infections in the report after you run - if it will not run changed the name of
TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
check with the other methods below.
http://support.Kaspersky.com/viruses/solutions?QID=208280684Download malwarebytes and scan with it, run MRT and use scanners online and other methods.
Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Malwarebytes - free
http://www.Malwarebytes.org/products/malwarebytes_freeSuperAntiSpyware Portable Scanner - free
http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGEAdwCleaner
http://www.bleepingcomputer.com/download/adwcleaner/
Run the malware removal tool from MicrosoftStart - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can
Download it here.Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=enTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
(viruses, Trojans, rootkits, etc.). who infected your computer despite safe
what you have done (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro--------------------------------------------------------
If necessary here are some free online scanners to help the
Microsoft safety scanner
http://www.Microsoft.com/security/scanner/en-us/default.aspxScan online ESET
http://www.eset.com/onlinescan/Scan Kaspersky online
http://www.Kaspersky.com/virusscannerOther tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------------------
After the removal of malicious programs:
Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
system files.Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
=======================================
=======================================Tests of memory intercept all errors such as memory do not match (possible even for sticks
seemingly identical) and when the faster memory is placed in system behind more slowly
memory. So it is best to also exchange the rods in and out to check these even if all memory
tests fail show a problem.To test the RAM here control - run 4 + hours or so.<-- best="">
www.memtest.orgFor Vista/Windows 7 memory diagnostics tool
Start - type in the search-> memory box - find top - click - right Memory Diagnostics tool
RUN AS ADMIN follow the instructionsWindows Vista: How to scan / test your RAM or memory with Windows Vista Memory Diagnostic
Tool
http://www.shivaranjan.com/2007/11/01/Windows-Vista-how-to-scan-test-your-RAM-or-memory-with-Windows-Vista-memory-diagnostic-tool/How to run the diagnostic tool memory in Windows 7
http://www.SevenForums.com/tutorials/715-memory-diagnostics-tool.html----------------------------------------------------------------------------------------
Could be a driver related issue however less inclined than memory. Update your drivers
manually looking at system and sites of the manufacturer of the device manufacturer.References to Vista also apply to Windows 7.
It's my generic how updates of appropriate driver: (look for updates to the BIOS and the driver).
This utility, it is easy see which versions are loaded: run DriverView - define the VIEW
for the drivers Microsoft hide - updated those without drain in their names. (Also updated
the BIOS and chipset drivers.)-Free - DriverView utility displays the list of all device drivers currently loaded on your system.
For each driver in the list, additional useful information is displayed: load address of the driver,
Description, version, product name, company that created the driver and more.
http://www.NirSoft.NET/utils/DriverView.htmlFor drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
Control Panel - device - Graphics Manager - note the brand and complete model
your video card - double - tab of the driver - write version information. Now, click on update
Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
Uninstall - REBOOT it will refresh the driver stack.Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
with their own software and drivers and all other main drivers that you have.Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
BIOS, Chipset and software updates on the site of the manufacturer of the system here.)Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
each installation.Always check in the Device Manager - drivers tab to be sure the version you actually install
presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
in particular that) so to install a driver - reboot - check that it is installed and repeat as
necessary.Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
manually by model.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers under Windows 7 (updated drivers manually using the methods above
It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
ORIGINAL TITLE: help... Blue error screen?
Help I get this blue screen error whenever I start up my dell computer... A problem has been detected and windows has shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: make sure that you have enough disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try which video cards. Check with your hardware vendor for updates to the BIOS. Disable the BIOS memory options such as implementing caching or shading. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical information: (0xc0000005, 0xF7c2815E, 0xf7C66864, 0xF7C66560 kdcom.dll - address F7C2815E base at F7c27000 Datestamp 4ed8a0bd
Thank you, I actually set myself a few hours after the announcement by starting in safe mode and scan with norton :) But thank you very much for the reply!
-
Help to fix the blue screen error: STOP: 0x0000007A
Original title: I get the BSOD on my Dell Inspiron 14 stop information is at the bottom. What means this dose-specific code and how can I solve this problem?
STOP: 0x0000007A (0xFFFFFFFFC0000056, 0x0000000058DB3860, 0xFFFFF8A000E42A48, 0xFFFFF960001E082C) he begins again each time after it happens like nothing ever happened, but I don't want my computer any crash if there is an easy way to understand what it means and set it would be nice.
Hello
Here are some of the more general methods that could help solve the problems of use as
necessary (same as in the link below).Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65-------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
This would help. Such as ITC and 4 others entered at the bottom left. And another error
information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
http://www.NirSoft.NET/utils/blue_screen_view.html
hangs and displays information about all accidents of a table - freeBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers under Windows 7 (updated drivers manually using the methods above
It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlHow to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">
-
Why this keep happening? -STOP: 0X0000007A
Sometimes my computer (running Windows 7 32 bit) will crash with a blue screen with this error code:
STOP: 0x0000007a (0x00000020, 0xC000009D, 0x86F29BDC, 0x00000000) and made a crash dump.Hello
Do you use a SSD? Or RAID? Double control "EVERYTHING" on the hard drive.
controller and wiring (from the discontinuation of ALL power first).
-----------------------------------------------------------------------------------------------------------------------Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
(also Windows 7)
http://www.winvistatips.com/disable-automatic-restart-T84.html===========================================================
BCCode: 7A 0x0000007A
The main causes of this error are virus/malware, drivers, memory, and disk damage. And
It may even be combinations of those so meticulous control of all is needed. Possible addition
the causes are such as the motherboard damaged material errors or other materials.BCCode: 7A 0x0000007A
Cause
Frequently, you can determine the cause of the error status (parameter 2) KERNEL_DATA_INPAGE_ERROR bug check. Some common status codes are:
0xC000009A or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of non-paged pool resources.
0xC000009C or STATUS_DEVICE_DATA_ERROR, generally indicates bad blocks (sectors) on the hard disk.
0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose wiring, termination or that the controller does not see the hard drive.
0xC000016A or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk.
0xC0000185 or STATUS_IO_DEVICE_ERROR, indicates improper termination or defective cabling devices SCSI or two trying to use the same IRQ.
These status codes are common ones that have specific causes. For more information about other possible status codes that can be returned, see theNtstatus.h file in the operating system Microsoft Windows Driver Kit (WDK).
Another common cause of this error message is the defective material or failing RAM.
A virus infection can also cause this bug check.
ResolutionSolve a problem of bad block: Generally, a status I/O of 0xC000009C or 0xC000016A code indicates that the data can not be read from the disk due to a bad block (sector). If you can restart the computer after the error, Autochk runs automatically and tries to map the bad sector so that it is more used.
If Autochk does not scan the hard disk for errors, you can manually start the disk scanner. RunChkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and runChkdsk/r.
Warning If your system partition is formatted with the FAT file system the long file names that use the Windows operating system could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.
Solve a defective hardware problem: If the State of e / is C0000185 and the paging file is on a SCSI disk, check the cabling and SCSI termination for problems.
Solve a problem RAM failure: Run the hardware diagnostics feeding by the system manufacturer, especially the memory scanner. For more information about these procedures, see the manual of your computer.
Check that all the cards in the computer are properly housed. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.
Look in the Event Viewer system log for additional error messages that might help identify the device that is causing the error. You can also disable caching memory BIOS to try to resolve this error.
Make sure that the latest Windows Service Pack is installed.
If the previous steps do not solve not the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can cause this error.
Solve an infection by the virus: Search your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.
BCCode: 7A 0x0000007A<-- read="" this="">
* 1137.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-Data-InPage-Error-0x0000007A-=============================
If you need search malware here's my recommendations - they will allow you to
scrutiny and the withdrawal without ending up with a load of spyware programs running
resident who can cause as many questions as the malware and may be harder to detect as
the cause.No one program cannot be used to detect and remove any malware. Added that often easy
to detect malicious software often comes with a much harder to detect and remove the payload. Then
its best to be thorough than paying the high price later now too. Check with them to one
extreme overkill point and then run the cleaning only when you are sure that the system is
clean.It can be made repeatedly in Mode safe - F8 tap that you start, however, you should also
Run them in regular Windows when you can.TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
It will display all the infections in the report after you run - if it will not run changed the name of
TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
check with the other methods below.
http://support.Kaspersky.com/viruses/solutions?QID=208280684Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
(If Rootkits run UnHackMe)Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Malwarebytes - free
http://www.Malwarebytes.org/products/malwarebytes_freeSuperAntiSpyware Portable Scanner - free
http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGERun the malware removal tool from Microsoft
Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can
Download it here.Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=enalso install Prevx to be sure that it is all gone.
Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
here or use Google to see how to remove.
http://www.prevx.com/ <-->
http://info.prevx.com/downloadcsi.asp?prevx=Y <-->Choice of PCmag editor - Prevx-
http://www.PCMag.com/Article2/0, 2817,2346862,00.aspTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
(viruses, Trojans, rootkits, etc.). who infected your computer despite safe
what you have done (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro--------------------------------------------------------
If necessary here are some free online scanners to help the
http://www.eset.com/onlinescan/
-----------------------------------
Original version is now replaced by the Microsoft Safety Scanner
http://OneCare.live.com/site/en-us/default.htmMicrosoft safety scanner
http://www.Microsoft.com/security/scanner/en-us/default.aspx----------------------------------
http://www.Kaspersky.com/virusscanner
Other tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------------------
After the removal of malicious programs:
Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
system files.Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
=======================================
=======================================Tests of memory intercept all errors such as memory do not match (possible even for sticks
seemingly identical) and when the faster memory is placed in system behind more slowly
memory. So it is best to also exchange the rods in and out to check these even if all memory
tests fail show a problem.To test the RAM here control - run 4 + hours or so.<-- best="">
www.memtest.orgFor Vista/Windows 7 memory diagnostics tool
Start - type in the search-> memory box - find top - click - right Memory Diagnostics tool
RUN AS ADMIN follow the instructionsWindows Vista: How to scan / test your RAM or memory with Windows Vista Memory Diagnostic
Tool
http://www.shivaranjan.com/2007/11/01/Windows-Vista-how-to-scan-test-your-RAM-or-memory-with-Windows-Vista-memory-diagnostic-tool/How to run the diagnostic tool memory in Windows 7
http://www.SevenForums.com/tutorials/715-memory-diagnostics-tool.html----------------------------------------------------------------------------------------
Could be a driver related issue however less inclined than memory. Update your drivers
manually looking at system and sites of the manufacturer of the device manufacturer.References to Vista also apply to Windows 7.
It's my generic how updates of appropriate driver: (look for updates to the BIOS and the driver).
This utility, it is easy see which versions are loaded:
-Free - DriverView utility displays the list of all device drivers currently loaded on your system.
For each driver in the list, additional useful information is displayed: load address of the driver,
Description, version, product name, company that created the driver and more.
http://www.NirSoft.NET/utils/DriverView.htmlFor drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
Control Panel - device - Graphics Manager - note the brand and complete model
your video card - double - tab of the driver - write version information. Now, click on update
Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
Uninstall - REBOOT it will refresh the driver stack.Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
with their own software and drivers and all other main drivers that you have.Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
BIOS, Chipset and software updates on the site of the manufacturer of the system here.)Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
each installation.Always check in the Device Manager - drivers tab to be sure the version you actually install
presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
in particular that) so to install a driver - reboot - check that it is installed and repeat as
necessary.Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
manually by model.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers under Windows 7 (updated drivers manually using the methods above
It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
My navigation bar has been accidentally closed (file, tools, refresh, and stop buttons, address bar, etc.) and now I can't get it back. I tried pressing F11 as someone suggested, but nothing happened. Please notify.
Use the ALT key on the keyboard if you can't see the menu bar, then
- View-> toolbars-> and select'Navigation bar tools "(and the Bar Menu)
- See the Navigation buttons such as back, home, bookmarks and recharge are missing
-
wdf 0x0000007E (0xc0000005, 0x88a56c9b, 0x8afca948, 0x8afca520) 01000.sys - address 88a56c9b base at 88a 12000 date stamp 4a5bbf28
BSOD happens only to reboot or shutdown.
Hello Pim857,
Often, we see crashes as a result of a program from loading at startup.
To solve these, we use the clean boot troubleshooting.
The following describes this process:
Windows XP:
http://support.Microsoft.com/kb/310353
http://support.Microsoft.com/kb/316434
Windows Vista and Windows 7:
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
Best regards
Matthew_Ha
-
Now PC crashes with the error"SPCMDCON. "SYS at ADDRESS FBFE7617 base at FBFE5000 date: 3dbdd" any suggestions? How to protect my pc and solve my problem and frequntly turn off my pc what I would do now?
Hello
When exactly do you get this error message?
Perform a clean boot to verify if a third asks the origin of the problem.
Refer to this article for help:
http://support.Microsoft.com/kb/310353Kind regards
Afzal Taher - Microsoft technical support.
Visit our Microsoft answers feedback Forum and let us know what you think. -
Get an error: PCI. SYS - address F76130BF Base at F760C000, Datestamp 3b7d855C
I had to repair windows XP home because of problems does not properly. Everything is well spent up to what I have turned off the PC & unplugged to replace the battery because she would not keep the time or date that the PC was unplugged. After that I started having a bsod with the following error "PCI. SYS - address F76130BF Base at F760C000, Datestamp 3b7d855C". There is more information above this error while ensuring that the hard drive is not complete & update bios I did everything but nothing seems to be working & whenever I boot from the XP CD I get only so far this error keeps coming back. I'm out of ideas & all my experience is not to help me with this error. Can someone help me with this little problem turning into a big headache?
Additional info: Asus M/B rejki Bios update applied, Intel Dual Core CPU E5000 @2. 60 - GHz, 1 GB ram, 160 GB hard drive 70% free, running XP Home SP3 fully up-to-date with.
Thanks for any help on this one.
Chris
Hello
You have windows XP CD with service pack 1/2 in it?
Step 1: Using Windows XP CD with service pack 1/2 he helped little to solve similar problems. Please make sure the installation disc has service pack inside.
Step 2: Try to switch to the original battery (if you have it yet) again to see if the problem persists.
Step 3: If you are able to enter the Recovery Console, and then run the following command at the command prompt.
CHKDSK /R
-
This error on a blue screen when I boot Windows xp pro. Welcome suggestions please.
Hi John,.
You can check the following thread link and advice given by Matthew_Ha, moderator of the Forum.
You can read the following article and check.
Maybe you are looking for
-
Auto unblocking "null" Apple Watch
My Apple Watch connects my rMBP and everything with macOS Sierra very well, but when my watch sends me a notification says "null" unlocked by this Apple Watch. How to replace the text "null"?
-
Force removal code error-8072 files.
I've had. MobileBackups.trash who took 600 GB of space, and I need to remove it. So I mv it was /Trashme and put it on my desk. Delete immediately will not work if its basket, used to empty the trash. File is locked. Nothing tried chflags-r nouchg, n
-
I tried packerguy solution and it didn't work. Any other suggestions?
-
Password login screen blackBerry Z10
The login password for the Z10 screen driving me crazy. It is too small and if I try to enter the password quickly, I end up by making an input error and wasting time to have to re-enter the password again. Is it possible to download a different op
-
EX90 to connect older home router (DSL Fritzbox 7390)
Hello My Cisco Ex90 is connected to the DSL connection at home. I want to call to an IP endpoint with accessible as IP as Cisco C20or EX90. I put the EX90 in H323 setting--> NAT the public IP address of my public IP address and it also has an interna