Stop the system with 06000008e - ati3duag.dll

Similar Questions

• Want J010dx m7: windows will not start until after full recovery of the system with new HARD drive

  Hello world

  I need help here.

  My HP envy m7 J010dx works perfectly with my original hard drive (1 TB).

  I am preparing a second HDD (NEW 320) as backup.

  I took off the Moose HDD (1 TB) and replace it with the NEW HARD drive (320GB) and try to do a full recovery of the system with the HP recovery DVD.

  After full system recovery and laptop computer needs to be restarted in order to continue, the laptop keeps restarting on the logo of windows 8.

  I think it says device not found Boot. Also a test using the UEFI tool material HP and all pass.

  Replacing the NEW HARD drive with the original of the old HARD drive and it start normally.

  What can go wrong here in this case? Thank you very much for the help.

  Concerning

  John

  OK, I read through the thread and this is my point of view on this based on works including restore process with the user created a recovery (UCRDs) media which the user indicated that they used.

  If you just want to jump to the conclusion at the bottom, you can see my opinion. If you want to know 'why' Please read the entire post.

  Model No.: m7-j010dx

  Product #: E0K83UA #ABA

  Ships OS: Windows 8 (64-bit)

  Recovery HP part No. Kit: 730336-002 (3 DVDs + extra)

  User replaced the HARD drive with a 1 TB hard drive 5400 RPM with HP ProtectSmart hard drive Protection a new hard drive is a Seagate Momentus 7200.4 ST9320423AS 320 GB 7200 RPM 16 MB Cache SATA 3.0 GB / s 2.5 "Notebook internal hard drive.

  With the help of UCRDs sent media recovery media (SSRDs):

  When the UCRDs are created, only the drivers for the HW operation (this is a critical point, that I will look later) are burned to the user created a recovery media.  Consider this a snapshot of the current HW, the base drivers and software applications.   If you change the HW on your laptop or desktop where the additional device requires a different driver for these features, a few questions you might - recovery process could stop because he can't find the right driver, a blue screen, a lack of start-up or other unstable system.

  A few years ago, I had a PC that would not recover because the Blu - ray (ODD) optical disk drive did not work.  I replaced the WEIRD Blu - ray with a generic DVD/CD burner into the new part of Blu - ray is presented.   I got the PC using SSRDs thinking I would put some time and just install the Blu - ray after the PC has been recovered.   The PC recovered and when the new Blu - ray showed I installed the unit and guess what?  All PCs have shown in Device Manager and applications was a generic ODD - no Blu - ray capability and ability to read Blu - ray content in the default HP provided for multimedia applications delivered with the PC.  Applications were there but no Blu - ray capability.

  Huh?  It looks that I did not put any time at all.

  I inserted the new Blu - ray ODD and distributed recovery with the HP SSRDs.

  After recovery, I had all the Blu - ray drivers and applications supported Blu - ray.

  The difference between UCRDs and SSRDs:

  UCRDs provide a glimpse of what is installed and functional both disks are created.

  Version Digest of the player on what is happening with SSRDs to retrieve a PC (before Windows 10):

  SSRDs have all the drivers for all the HW and SW qualified for the unit.  There may be several drivers for hard drives, different types/screen resolutions, sides, etc.  Based on the characteristics of the specific laptop / desktop a process is run called "Do / don't.   After entering the recovery SDRD, the Notebook media boots to Recovery Manager.  The first step is a raw copy of all the contents of the disc on a temporary partition.  Following the Do / do not process looks at the characteristics of this specific unit and remove all other drivers and applications not used by this device.  Drivers and the only successful applications are the features supported.   And then, the new operating system and recovery partition is created.   The PC end recovery of cleaning process and restart the laptop / desktop. And, Yes, you guessed it, if you create the user created a recovery media, you only have the drivers for HW devices and applications of HP on the PC at the time.

  So, that being said, what could be the cause/solution?

  Hard drives can be different enough so that a different driver (not the UCRDs) is necessary for the newly installed HW.

  The SSRDs are supported on the new HARD drive installed?

  I don't know, I have an office boy, and I have not tried on this model of laptop.

  If you have / acquire SSRDs, I recover the laptop with the new installed HARD drive and see if it works.  It may or may not.  I don't know what drives were qualified for this laptop.

  If this does not work, the last option is cloning via USB connection (old HARD drive in the PC, new HARD drive connected to a USB 3 via the SATA Adapter (dongle) USB port, install or download software cloning and cloning the old HDD to the new.)   I just did this on the two older Windows 7 computers laptops using a SanDisk Ultra kit.  He has worked on both units.

  Conclusion:

  I don't think that the problem is caused from a HARD drive of 1 to a 320 GB HARD drive, as it meets the minimum specs for a complete installation.  I think the problem is related to the use of UCRDs to retrieve and the UCRDs do not have the HARD driver/firmware/application disc.

  But then again, I know.

  I am an employee of HP...

• Partition problem after the recovery of the system with a single key 6.0

  I need your help!

  My Lenova Ideapad Y430 not more start and I had to restore the system with the recovery CD I burned with a recovery key 6.0. The restore process showed no defects and no error has occurred.

  Now, after restaring the system I only 0 with a C: partition (all program files, vista, drivers etc.) 104 GB and the 'part of recovery for a key' 14.75 working. D: partition where all my documents, pictures etc. are stored are listed, but idle and not accessible nor editable with the tool Vista Diskmanagement.

  No idea what I can do?

  You can download EASEUS partition manager. It will help you to reformat the D drive.

• Envy 17 2180el can I add a second hard drive, and then choose bios/boot of the system with which to start?

  Envy 17 2180el can I add a second hard drive, and then choose bios/boot of the system with which to start?

  in the case give me the link of a hard disk of type to add

  Hello

  While you can certainly add another HARD drive in the Bay of secondary drive (you must also support and the connection cable) you can't boot from it - only in the Bay of primary HARD drive is bootable.

  Kind regards

  DP - K

• I'm running a full scan of the system with my anti-virus software and it filled almost my laptop crashes, problem with the vga865.fon file

  I'm running a full scan of the system with my anti-virus software and it filled almost my laptop breaks down when it comes to: -.

  c:\windows\winsxs\x86_microsoft-Windows-font-bitmap-oem_31bf3856ad364e35_6.0.6000.16386_none_fb2d5aefb17b8d65\vga865.FON

  This file can be replaced.  When I scan this folder individually its fine, please help

  Thank you

  Hello

  What protection software antivirus you are running on the computer?

  Method 1: Check if you can run the scan in safe mode without in all questions

  Follow the steps mentioned in the link below to access the secure mode
  Startup options (including safe mode)

  Method 2: you can run Safe Mode security monitor, see the steps in the article below
  How to install the free Windows Live OneCare Safety Scanner and then scan your computer in Mode safe

  Method 3: Follow the steps mentioned in the link below to check your hard disk for errors, and then check if the problem is resolved
  Check your hard drive for errors

  If the problem persists,

  Method 4: Long file name could cause this problem, perform a backup of the file (copy it somewhere else), and then rename the file, check to see if that makes a difference

  Note: Copy the file to the original location.

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Pavilion dv4: Windows 7 does not start and I can't access the system with f11 recovery

  I use a Pavilion dv4. Windows just crashed on a blue screen with a message about physical memory dump. Now when I start the computer it will just a black screen with a blinking cursor to the place when windows normally should start. I can not access the system with the f11 key recovery. I went in with the f2 key diagnostic mode. Diagnostic tests except for the battery test that failed, but shouldn't the laptop to be able to run without a battery if it is connected? And besides, if the problem was the battery, the laptop wouldn't be able to turn on at all, no?

  I'm not about to spend all that money on a battery just to know that it is not the battery.

  Hello

  If you have the 64 bit rescue CD, you would have received an error if it was bad.

  Once you have all your data backup, try the following - which means that Windows has been installed on the C Partition.

  Boot from the new rescue CD, select repair your computer and choose the command line.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the rescue CD and try to restart now.

  Kind regards

  DP - K

• Blockages of the system with El Capitan

  How can I stop my system crash after installation of El Capitan in October?  He planted 3 times since then. Would not boot.  Instead of the Apple logo - was a circle with / thru in the middle.  I used Firewire for restore from my MacPro.  Have currently updated to OS X 10.11.3 installed.

  Is there no remedy?  I am so disappointed with this product!

  Start in safe mode

  <http://support.apple.com/kb/ht1564>

  In almost EVERY case to install El Capitan and experience an accident, it is caused by the 3rd party software previously installed by the user.

  Start in safe mode does NOT load that 3rd party software, causing the crash.

  Thanks for posting the reports Kernel Panic: "/ Library/Logs/DiagnosticReports".

  <http://support.apple.com/kb/ht2546>

  <http://support.apple.com/en-us/HT200553>

  The panic report should have "panic" in the name of the file.

  You could also post the EtreCheck output for the forum to analyze and made suggestions on your system.

  <https://discussions.apple.com/docs/DOC-6174>

  <http://etrecheck.com>

• How to restart and stop the system by running a batch file?

  Can any body give the command batch file for restart and stop of the system.

  My requirement is to reboot or shut down the system at a specific time. So I think that by creating a batch file, that I can schedule the file to run at a specific time of the scheduled task...
  With regard to:
  Rahma.

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited on MSDN. Please post your question in the MSDN forums. You can follow the link to your question:

  http://social.msdn.Microsoft.com/forums/en-us/categories

• Error message: "Preparation set up windows, do not turn off your computer" when to stop the system.

  Original title: closure of the problem

  Almost everytime I turn off my laptop, I get the message ' Preparation set up windows, do not turn off your computer . Then it takes forever to finally stop. Suggestions for this problem?.

  Hi ArthurCosford,

  This screen appears when you have pending Windows updates must be installed on the system or when you installed the Windows updates on the system.

  Step 1:

  You can check the windows updates history to discover updates recently and failed to install.

  For more information, you can consult the following article:

  See the Windows updates are installed

  Step 2:

  If there are updates failed, then try to download and install the stand-alone package with updates from the Microsoft Download Center.

  a. to download updates from the Microsoft Download Center

  b. Enter the item number in the field search and download the same.

  c. double-click on the downloaded file.

  d. click on run and follow the wizard to install it.

  Hope this information is useful.

• Stop the preloader with a keyboard shortcut?

  Can I stop preloader with a keyboard shortcut?

  Sometimes I go to a site, & the preloader takes a loooong time. I already saw that I don't want to stay there, but are unable to leave until the site to load completely.
  Y at - it a shortcut that will stop the preload, & perhaps leave the site?

  CTRL + W seems to do the job when I tried earlier. If I have other problems, I will try other solutions.

  THANKS for the quick help!

• Mail creation of massive log files and stop the synchronization with the server

  Since the upgrade to El Capitan (10.11.1), Mail presents two problems persist:

  (1) it generates massive log files, e.g. 2015-12 - 03_IMAPSyncActivity.log these files regularly exceed 10 GB and block Mail and freeze the Mac. Mail can be over 8 GB of RAM. Once removed, Mail recreates the file and fills again, ends up doing more massive files that must also delete.

  (2) mail stop sync with my different IMAP e-mail servers. The only solution I've found that it completely delete the or the e-mail accounts and reinstalls the account. It works for a day (or even a few hours) before it just stops the synchronization, even if a connection test shows he connects with the server. This problem seems to occur on two e-mail accounts separately on two different servers / hosting companies, but not on my Gmail accounts.

  These two problems occur on both my iMac (21.5 ", mid-2011, 2.5 GHz Intel Core i5, 8 GB RAM) and MacBookPro (13', mid-2011, 2.5 GHz Intel core i5, 4 GB RAM).

  Full of ideas gratefully received!

  Thank you!

  Please take these steps to remove the mail folders 'sandbox '.

  Step 1

  Back up all data.

  Triple-click anywhere in the line below on this page to select this option:

  ~/Library/Containers/com.apple.mail

  Right-click or Ctrl-click on the highlighted line and select

  Services ▹ Reveal

  the contextual menu.* A Finder window should open up with a folder named "com.apple.mail" selected. If this is the case, move the selected folder - not only its content - on the desktop. Open the window Finder for now.

  Restart the computer. Launch Mail and test. If the problem is resolved, you may have to re-create some of your e-mail settings. Any writing paper custom that you created may be lost. Ask for instructions if you want to keep these data. You can then delete the folder that you moved and close Finder.

  CAUTION: If you change the content of the sandbox, but leave the folder itself in place, Mail may hang or starts any. Remove the tray to sand everything will be rebuilt automatically.

  Step 2

  If step 1 does not resolve the problem, repeat with this line:

  ~/Library/Containers/com.apple.MailServiceAgent

  * If you do not see the item context menu copy the selected text in the Clipboard by pressing Control-C key combination. In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

• Stop the loops with a button

  I have an infinite loop is and display of data. How can I end the loop with a button or a keypress?

  Periodically perform a ProcessSystemEvents() call inside the loop. In a reminder of the STOP button, set a flag to indicate your loop to stop.

  stop unsigned int = 0;

  While (! stop) {}

  data getmeasured

  display the data

  ProcessSytemEvents()

  Sleep (250);   to be polite: it is impolite to spinlock, since you will monopolize the CPU and other threads can get hungry

  }

  then, in the reminder for a STOP button

  STOP the button callback routine

  stop = 1;

• Recover the system with recovery disks

  I have a Pavilion Elite desktop computer. I tried to reset/recover my system with the recovery disks that I created when I bought the system. But I get the following messeage: "system recovery disks do not support this computer. You cannot restore this system with these discs. "GOOD, then I thought that my disks must be bad and ordered a set of HP. I come from them and tried again to restore my system... EVEN COMING? What's wrong? Need help.

  The recovery disk problems Troubleshooter need effects?

  There is another thing that you could do that provide the Windows key is always visible on your COA sticker.  Since it was a multi-configurable system you should know it was professional, Home Premium or ultimate edition. Please be aware that what I propose will not contain the goodies HP provided with recovery disks, you will need to reinstall all your programs and data.

  Go to this site and download the version of Windows 7 ISO which matches what you had initially and have your key ready.

  http://www.heidoc.NET/Joomla/technology-science/Microsoft/14-Windows-7-direct-download-links

  Once downloaded the file ISO, you can burn on a DVD using the Windows 7 DVD drive or another DVD burner you have:

  http://download.CNET.com/Windows-7-USB-DVD-download-tool/3000-18513_4-10972600.html

  See also this site for more information:

  http://www.microsoftstore.com/store/msusa/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Once downloaded and burned to DVD, use it to try to install Windows 7 on your computer.

• How to stop the program with 2 cases of event

  I know that this is a very easy solution, but I can't seem to find it.

  I have two cases of the event in a while loop. I worked previously with the case of an event, so I placed the button stop in the case of the event. However if I have 2 cases of the event can't place the button stop in one of them so, how can I stop the program then?

  If the stop button is outside of the case that the program will not stop.

  Here's my vi of adding two different values for output according to which key

  Add a change event value case more for wire to terminal under condition of loop and stop button.

  find the attached VI

  Kind regards

  Chick S

• I can't access the folder of "OWNER" in a "MY BACKUP" folder after restoring the system with a backup.

  I did a restore of the system a couple of weeks.  I have an emachines with AMD 64.  I chose the backup option which programs, files, etc., placed in a folder "my backup".

  I tried to find photos and music in the folder, but I could only access the music folder.  When I try to go further in the folder, I get in the 'owner' folder but a message box appears and says that I don't have access to this folder.

  I am sure that my photos are of him, but I need to be able to access the folder.  How can I change the settings so I can access?

  Try "taking possession" of this file...

  "How appropriate a file or a folder in Windows XP"
    <>http://support.Microsoft.com/kb/308421 >

  HTH,
  JW