redirection of IP in FWSM in routed mode.

Similar Questions

• ASA 5510 - possible to fill the 2 interfaces in routed mode

  Cisco ASA 5510 with security more license, version 9.1 (5) running in routed mode.

  I want to fill two interfaces for example: eth0/2 and 3/eth0 and configure an IP address / network while leaving the ASA 5510 in routed mode. I know that this is possible in transparent mode, but I need to keep this in routed mode. I know I could configure a single interface and connect a switch but my client does not want to do.

  Otherwise, my only thought would be to configure each interface eth0/2 and eth0/3 as a network traffic and the route of subnet separate between the two.

  Any help would be appreciated!

  Thank you

  Andrew

  Andrew

  That would help us answer you better if we understood more about what your client and you want to accomplish. But to answer the specific question you asked, I don't think it is possible in an ASA5510 in routed mode configuration Eth2 and Eth3 to share a single IP address.

  Linking to Eth2 and linking to Eth3 Are they really the same subnet?

  HTH

  Rick

• ASA 5505 in router Mode can implement the MAC ACL

  Hi all:

  My client request can the Cisco ASA 5505 implement MAC ACL in Cisco ASA 5505, who is now running in router Mode.

  Can anyone help answer this?

  I tried to search the document and also tried the ASDM in the Cisco ASA 5505 but couldn't see a way to do the ACL by MAC address.

  At the same time can also help me find the command line using the ASA 5505 able to run MAC ACL in router mode?

  Thank you very much!

  Warm greetings,

  TangSuan Tan

  MAC ACL is not supported in Routed mode, only in Transparent mode.

  Here is the command for your reference:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/A1.html#wp1598101

  And here is the ethertype supported:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/access_rules.html#wp1083699

• Need to put the modem/router mode single modem

  I have a netgear router and a modem/router of calix. I want to say as a modem. I called my ISP and they are no help. I have connected to the gateway and I have experience with the network settings. How can I put it in the modem settings, strictly without the help of my ISP? Thank you

  Who needs to put the router in Bridge mode. The router would then become transparent. Unit acts as a modem only. If you don't know how, ask your ISP.

• WAP54G Repeater, which router mode?

  I have two WAP54G that I used to set that repeaters, but then I had to change my router to a WRT120N... But then I discovered only works with WRT54G Repeater mode, so I had to buy another.
  I bought a WRT54GH.

  I was not able to repeat the operation successfully with this router.   This is what happens to be WRT54GH will not be repeated like the WRT54G? So which router do I need?  If I didn't change my router, how to repeat the signal?

  Thank you.

  Yes. You can use WAP54G and connect directly to the modem to provide a wireless connection. Then, try to repeat the WAP54G signal rather than the signal from WRT54GH. I think WAP54G can repeat if connected with WAP54G wireless signals.

• Router mode in RV042G

  Is there documentation on setting fashion RV042G router and change that to its topography?  The manual tells simply click on the button to change the mode! 4th grade student could understand that - but what is his role in the unit?  It essentially becomes a glorified with Internet switch?  The 2nd WAN port can be used as a switch node?  Is there a white book somewhere that gives this info?  I looked for hours.

  Gateway with a subnet of the DMZ mode.

  -Tom
  Please mark replied messages useful

• East-redirection of possible connection when the routing service is disabled?

  Possible when connection redirection is the routing service is disabled in win7? I find that this is the case on the following resource monitor. It comes to my ISP. They can redirect my connection like that?

  Hello Newman,

  Thank you for your response.

  I would like to inform you that if any Internet Service provider changes of place, it's legal and it does not affect Internet connectivity.

  Please let us know if you need more help.

  Thank you

• Redirection of files that previously were routed on Vista Home Premium

  Hello

  I'll explain that a little more in detail. Before a BSOD that required me to use the image of a Builder to retrieve, I had a few user folders redirected to C: files on the D: drive on drive D: files were left intact i.e. they were not affected by the image recovery. Only C: drive has been restored to the original image.
  I need to implement a method that will be the Windows files on the D: drive when normal access Windows for new user on C: files occurs.
  I tried a redirect that seems to move files that I don't want to do. Because the files on the D: drive came out of the original redirection, if I use the option "Restore Default" on these files, and then to have the original values for drive c: means that they copied just return, once again something I want mainly because it reduces the space on the C: partition.
  Can I create a kind of link to point (and not move) on the D: drive?
  TIA

  I'm glad to know that you have solved the problem. In case, if you need help you are always welcome to post your questions and your valuable suggestions in this forum.

• (Redirected) Dell Inspiron 15-5568 in tablet mode using - how to pull up a Yahoo email message

  I just bought an Inspiron 15-5568.  I put it in tablet mode, and I'm trying to get back an email in my Yahoo Inbox using IE.  I double click on one of the messages of email in my Inbox to pull up.  Instead of pulling up the message, double-click zooms the screen IE.  Another double click the zoom back again. I tried a number of different operations to get back an e-mail message, but nothing works.  I can get a context menu to appear next to a message, but there is no option to read or view the message.  If I was using a mouse, I would double click on the message and it would come.

  I have reviewed the user's guide, but it is not a great help.

  Can someone tell me please how to pull up an email message in Yahoo or Google Mail with an Inspiron 15-5568 in tablet mode?  It seems like it should be very simple, but it isn't.

  Thanks in advance.

  Hi RexFarris,

  Please repost this in the laptop computer Forum help.

  http://en.community.Dell.com/support-forums/laptop/f/3518

• FWSM Configuration problem

  Hello

  Please can someone help with the following problem:

  I have 659 with FWSM, I configured the FWSM in routed Mode unique.

  My requirement is to make the MSFC behind the firewall, so I need only two VLANS to act as a firewall interfaces, all other VLAN should through the MSFC.

  I used the vlan 100 as inside of VLANs and vlan 101 as Vlan outside and I did all the required configurations on the 6509 (switch, MSFC) and the firewall.

  The problem is: outside VLAN (101) is not coming on the MSFC even if there is an active port on this vlan (which is the router connected to the VLAN outside!)

  Why this vlan is not coming? Help, please

  This is the configuration I used on 6509 and FWSM (I included only the related configuration)

  ON FWSM:

  -----------------

  nameif vlan101 off security0

  nameif vlan100 inside the security100

  IP outdoor 62.149.76.2 255.255.255.248

  IP address inside 10.8.100.2 255.255.255.0

  Route outside 0.0.0.0 0.0.0.0 62.149.76.126 1

  Route inside 10.8.0.0 255.255.0.0 10.8.100.1 1

  6509 (Switch):

  --------------------

  name of vlan 100 inside set

  name of vlan 101 Set out

  define the vlan 100-101 firewall - vlan 8

  6509 (MSFC):

  -------------------------

  interface Vlan100

  Description inside of vlan

  IP 10.8.100.1 255.255.255.0

  !

  interface Vlan101

  Besides description of vlan

  IP 62.149.76.1 255.255.255.248

  ----------------------------------------------

  Yes, that's correct. This way you will get a unique link between the MSFC and FW.

  For your MSFC your default gateway will be 10.8.100.2. Inside networks for your FW, will point to 10.8.100.1, that you specified. There is no need for interface VLAN 101 of the MSFC. Keep 101 as is, otherwise.

  I hope this helps.

• Bridge mode... Router and TC

  My internet does not work if I have my xfinity on bridge mode router and my TC on mode bridge?

  Bridge on the modem/router and Bridge Mode on the TC will not work.

  Xfinity modem/router must be configured as a modem only simple only (in bridged Mode), and the TC must be configured in router Mode of DHCP and NAT

  or

  Xfinity modem/router must be configured normally as a modem/router, and the TC must be configured in Bridge Mode

• Bug of Linksys WRT54GC Mode of operation of "router"?

  I use a Linksys WRT54GC router and I experience a behavior that I don't expect.
  You give me your opinion?
  This is the case:

  My assumption of "Gateway" or "Router" operating Mode is:
  Gateway mode means NAT that makes invisible LAN subnet side WAN addresses. NAT is disabled by activating the Mode of operation of 'Gateway' to 'router '.

  I have connected a PC (192.168.2.100) to port the router WAN and another (192.168.23.100) PC on a LAN (192.168.23.1) of the router (192.168.2.2) port.
  When I switch my WRT54GC "Router" mode I can't always ping the PC on the site of the side router LAN WAN. SPI Firewall protection and block anonymous Internet requests are disabled. Firewalls on both computers is disabled.

  I saw a similar problem at the forum "Connecting two routers via WAN" 08/28/2008 Victor Tang.

  Don't you think that it is a bug in the mode of operation of the WRT54GC software?

  I reported the bug to Linksys.

  My first experience with Linksys technical support is very good.

  They take the serious problem, ask for the discharge of Wireshark and send me an update of the firmware of the router.

  This fixes the bug with the mode of operation, now I can without NAT on and outside, very well!

  I don't have firmware update earlier because the release notes did not mention my bug, I read in the forum a lot of users having problems after the update of the firmware, so I followed the policy do not update unless it can solve your problem.

  There are some things perhaps worth mentioning:

  You should be careful to use the right firmware for your router.

  Not only the model of the router is too important, the hardware version and too country!

  I've got a WRT54GC, hardware version 1, and it is the type of the EU.

  Of this material, there's also a different US with versions of firmware version!

  The latest version of the firmware to the US type is v1.60.1, the latest version of the EU type is 1.60.0 v.

  Thus, you should take care of this website, you download the update to get the right version and read the release notes. These release notes, you can check if your current firmware version is part of the history of this firmware, so you know that you have the right one. I was so very accurate because many have reported problems in the forum with updates.

  Now I'm able to Exchange traffic between computers and printers in different subnets and I can access the Internet from each subnet gateway I want.

  It is important to think about the configuration of your PC and routing tables.

  The firewall on the computers must be configured on the additional subnet.

  A PC has a default gateway to reach a device on another subnet.

  Most of the time these are devices on the Internet, so if you create additional internal subnets that your traffic will be by default will be send to the Internet and will be lost. To define additional gateways where your additional subnet can be found to avoid this.

  This can be done on a PC with the command: route add (IE 192.168.23.0 mask 255.255.255.0 192.168.2.2) or you define a static route to your router (the latter is preferable).

  The problems I've had, forced me to consider how does networking, with the help of the users on this forum, I would conclude that this is a bug, with the support of very good Linksys everything now works as expected.

  Thank you.

• Switching mode of EPC 3925 / router E3000 speed 20% loss

  my setup is EPC 3925 Switch mode - E3000 router mode

  my ISP speed is 200 Mbps I only have 160 MB/s maximum and is not stable

  When I use the EPC 3925 I get 200 Mbps

  can someone explain why this happens

  takwansani wrote:

  Thanks Meegosh and nerD_sayer for answers

  one last question what happens if ask my ISP to swap the 3925 to a modem router as the 3208

  I gain speed?

  Yes. It is better to have just a modem ordinary to avoid double NAT issues as well as port easier opening if it is necessary to do so.

• WRT600N: How to switch mode to 'Bridge' to 'router '?

  I already posted a messageasking if the WRT600N could be wireless connected w / my new WRT610N. The answer I got was no, I had to wire up together. Well, fair enough - it's been a long shot. The person who answered referenced this set of instructions, I've read before, when I linked the WRT350N w / my previous 600N (cable).

  The problem now is that in these instructions, when he says to go the the "advanced routing" page and change the mode in the drop-down list of 'Gateway' to 'Router', the WRT600N does not have a drop down box - all there is "NAT", radio buttons marked "enable" or "disable." (I tried to insert a picture of the page, but cannot find a way to do that here.) Even the little "help...". "link out side says that there should be a drop-down list box, but there is not.

  I guess I should I put 'NAT' to people with disabilities, that would achieve the same thng than to change the 'Gateway' to 'Router' mode, but I wanted to check here first and see what the official word. So should I set 'NAT' to disable to move my 600N mode to the "router"?

  Thank you! This is good info to have. And looking at the "Advanced Routing" instructions, I notice now that they have dynamic RIP (Routing) active, but the "yellow flag" instructions don't say nothing about it, so I didn't change the disabled. The dangers to do these things later in nite!

• Router WRT54GS, how to set up the infrastructure mode.

  Hello

  I'm new in this forum.  I have been using this router for many years.  I have two desktop computers and a laptop computer, the first two connected by cable, wireless laptop.  I got a lcd tv got a (wireless) lan connector and want to access the internet with my TV as well.  The manual of the TV says that he accepts the router mode infrrastructure and no ad-hoc.  According to me, the first time that I have configured the router was punctual and now I want to change to the infrastructure.   I've looked everywhere and many people say to go to set up the wizard provided in the cd of the router but I did and I don't see the option to select the option at all.  Could someone help me to find a way to fix it?  I'd really appreciate it.

  Thank you guys for your help.  Tonight, I tried several times until it worked.  No idea, but it works now.  Case is closed.  Thanks again.